E3000 High strength, low speed

I have a laptop that's G band wireless, the top speed that get is 2.0 Mbs. WHen I swap it out with my old Linksys, I get top speed of 54Mbs. I tried "all" settings on this router. BTW I get the same low speed with my other G devices too. I'm beginning to feel that the e3000 is not G band friendly.

Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
This settings are for 2.4GHz wireless network :
- Here select manual configuration...Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbors network...
- Set the Channe Width to Standard-20MHz and change the channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select TKIP...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and remember the key.
NOTE : Passphrase should be more that 8 characters...
Click on Advanced Wireless Settings
Change the Beacon Interval to 50,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 and Click on Save Settings...
Now see if you can locate your Wireless Network and attempt to connect...

Similar Messages

High speed and Low Speed CAN

Hi
This is my first time to use CAN.
I have LabVIEW 2010 and LabVIEW FPGA
I have NI 3110 Dual-Core Industrial Controller with Windows OS, NI 9157, NI 9852 CAN Low Speed Module and NI 9853 CAN High Speed Module to be used to monitor the CAN messages from an ECU unit.
The connection is done as the following:
·         The High speed CAN is connected to the NI-CAN 9853 (Port 0)
·         The low speed CAN is connected to the NI-CAN 9852 (Port 0)
·         The baud rate of the 9853 is 500kbps
·         The baud rate of the 9852 is 50kbps
·         Both modules are set to “Listen Only”
·         “Module Clock” in both modules is set to 20MHz
·         CAN networks are 29-bit and 11-bit.
My consideration is to read all the messages from both modules without losing any message. Below is a picture from the block diagram on the FPGA target, is this the best way to read CAN messages from both modules? Also, could you please suggest what is the best way to read the messages on Host vi?
Unfortunately, I do not have the module right now to do some test, so that I cannot get the iteration time (“CAN Low Speed Loop” and “CAN High Speed Loop” show in the picture below), could you please tell how to calculate the iteration time needed for each loop depending on the above information.

The way that you have proposed to use the CAN module to monitor the BUS is a bad idea. We have a prebuilt driver that will do most of this work for you. You will need to download and install the NI-CAN 2.7.3 and then you will be able to use the example finder. In the example finder look for.
The example finder is accessed through the Help menu.
Jacob K || Applications Engineer || National Instruments

Low speed connection, but still have input history.

Hi there,
We have done some tests in our business to see the performance difference between "low speed connection" being enabled and disabled for a system, both from a network perspective, and from a performance perspective on Citrix servers.
We have determined that the 'input history' feature doesn't cause much performance impact, but a lot of the other 'high-speed' features like images and tool tips do.
We would like to be able to have "low speed connection" for our system, but still enable 'input history'. Is there any way this can be achieved, such as through INI or registry changes?
Thanks,
Michael.

I raised a message with SAP, and they responded saying that this is not possible

Netflix movie resolution phases in and out of high and low.

When I'm watching a netflix movie even with WiFi the resolution phases in and out of high and low resolution. Does anyone know what is causing this?

Yes, you download speed is changing. If the download speed is not great enough for HD it reverts to SD.

USB Mouse:usb 2-2: new low speed USB device using uhci_hcd and address

usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: new low speed USB device using uhci_hcd and address 2
again , again...
My mouse not working.
Please help me.Thank you.

I have same problem. The command "lspci" return for audio card:
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06)
When "modprobe oss_hdaudio" system freeze.

How to use PCI-CAN LS (low speed can bus card) with hi speed devices

I'm having problems connecting the low speed card to the hi speed devices: I've setup the bus with 120 ohms resistors terminating it. The devices seem to be working fine but the can card doesn´t seem to receive or send anything. It has rth and rtl of 510ohms. The card and devices are at 125kbps. I ran the card diagnostics and it passed them. Is it really possible to use this low speed card with a hi speed bus? Don't I have to do something special for it to work on hi speed bus? Any sugestion is highly appreciated! thank you

Hello Danut,
I was able to set up a Low Speed CAN card to talk to a High speed port on another computer( simulating a high speed device). I did not have any termination resistors on the cable. Initially, I saw the same Comm errors you mentioned and this was because the cable I was using was internally terminated. So please check that the cables are not terminated. Also , verify that the high speed device itself is not terminated ( measure the resistance between CAN_H and CAN_L, with the cable connected and without the cable).
Let me know if you were able to get the system up and running. Also do you have any low speed devices that can be used to test teh CAN card with?

Low Speed Connection

Hello all,
Do some of you have idea of the impact to unset low speed connection option in saplogon.ini file ?
We have about 10000 users on 20 SAP productions systems in Europe.
At the moment, our saplogon setting is with low speed connection option but a lot of users required historic functionality in input field and we ask ourself to unset this option to allow high speed connection.
The problem is that we don't know exactly what can be this impact on this on our network bandwith ?
Any suggestion ?
L HENRY

Hello Laurent
please pay attention to the SAP notes
161053 -> https://service.sap.com/sap/support/notes/161053 and then
1250939 -> https://service.sap.com/sap/support/notes/1250939 and then
203924 -> https://service.sap.com/sap/support/notes/203924
Hope that will clarify your questions...
Best regards
sven

Receiving 'low speed usb 1.1' error when syncing

I updated itunes to 10.0.1 a day after it was released and have synced my ipod a few times without any problems. A few days ago, an error message popped up when I connected my ipod saying that my ipod was connected to a "low-speed usb 1.1 port" and says I should "connect to a high-speed usb 2.0 port if one is available on my computer". The sync seemed to be slower than usual. My mac mini only has usb 2.0 ports and was connected directly into the computer and not to a usb hub.
I have reset my ipod, restored it, and restarted my computer and still receive the same error message.
Has anyone received a similar message and have any suggestions on what I can try next? Any information would be greatly appreciated. Thanks.

Receiving an 0xE error you will want to run through the following:
http://support.apple.com/kb/TS3221

Low Speed Internet - on iMac Only

Hi,
I have an early 2008 iMac running 10.9.5.
Recently the WiFi on it has been running painfully slow, compared to the other devices in my home. I thought it was due to the location in my home but it doesn't appear so as I've compared it to a Macbook.
The iMac's speed test results in download speeds between: 1.2 and 5.6 mps.
The Macbook's speed test results, when right next to the iMac: 25 mps.
Around where my airport is (downstairs), speeds on the Macbook are 50+ mps, which is what I am paying for.   (The iMac is upstairs.)
Is there a way to fix this so the iMac runs at the ~25 mps like the Macbook does? Is this a general problem with Mavericks, which I've read from others?
One solution I tried which did not work is: Go To> /Library/Preferences/SystemConfiguration > Delete the files, reconnect and get a fresh reconfigure. This did not solve the problem.
Any help would be greatly appreciated!

On the iMac (machine getting the low speeds)
PHY Mode: 802.11n
Channel:   1 (2.4 ghz)
Security: WPA2 Personal
Signal/Noise or RSSI: -81
Transmit Rate: 39
On the Macbook Pro 10.9.5 (machine getting high speeds)
PHY Mode: 802.11n
Channel:   1 (2.4 ghz)
Security: WPA2 Personal
Signal/Noise or RSSI: -75
Transmit Rate: 156
Hmmm, so clearly the Macbook Pro has a much higher transmit rate. Is that fixable?

When home sharing songs are transferring at an extremely low speed. why is this happening??

Hi
I shared my library with my Husband's library using the same apple id. I then tried to copy songs from that library to mine. But the songs are transferring at a ridiculously low speed. When he copied the songs from my library it did not take as much time. Can you please tell me why this is happening?? Is this a problem with the itunes??

Hi systemBuilder, you are not alone in your frustration. The problem is the plugin model: plugins are allowed to do much more than they can be trusted to do intelligently. Without a change to that, Firefox cannot stop the Flash player from changing window focus.

How can I extract high and low parts of a string that represents a 64bits decimal number?

I want to extract the high and low parts to interpret it and convert to binary code, but such a hugh number (represented by a string) isn't easy to extract from the string directly its high and low parts.

LabVIEW can't handle a 64-bit integer. You will have to store it as two 32-bit integers. If you need exact math on those 64-bit intergers you will have to make up your own routines to handle the carries and what not. If you just need pretty good accuracy, covert both 32-bit integers to double, multiply the upper 32-bit number by 2*32 (also a double) and then add the lower 32-bit number to it.
Good luck.

I Can't Burn a CD any more! and a lower speed does nothing - HELP!

I have been burning CDs on this machine (imac 10.3.9) the same way for years and years. (7)
Up till last month.
This is what I get when I burn a playlist.
"itunes can not burn this cd because your burn speed is too fast for you cd burner or media. Choose a lower speed in the burning pane then try burning again."
I've tried that - even though that seems silly considering I've had no problems at my current settings until now. The lowest burn speed (1) gives me the same error.
I'm hating life and my mac right now, something I though I'd never say.
Anyone?

If you don't have Nero, check out http://discussions.apple.com/message.jspa?messageID=9229334#9229334. I think some people have found a way to get just the Burn Rights program.
If that doesn't work, some people seem to have luck with editing the registry or messing with filters or gear drivers. Check out this discussion starting with Tytus (he came up with the Nero fix) on March 22:
http://discussions.apple.com/thread.jspa?threadID=1939904&tstart=0
Hope this helps!

Make USB-6001 digital output always high or low in C

Hello all,
I am new to the NI DAQ interface. I have an USB-6001 and I am trying to use this device to control some logic circuit in C. So what I want to do is:
* set some digital output lines to high or low levels, and change their status when needed (in C).
I have tested the device in NI MAX -> Test Panels, and found that the device is able to do this. Then I try to do it in C. I hace checked the examples, and the function I should use is the one called "DAQmxWriteDigitalU32". I have problem in understanding its input parameters. I have tried something with my own understanding, but it does not work as I expected. Here is one test I did:
uInt32 data=1;
int32 written;
TaskHandle taskHandle=0;
DAQmxErrChk (DAQmxCreateTask("",&taskHandle));
DAQmxErrChk (DAQmxCreateDOChan(taskHandle,"Dev1/port0/line7","",DAQmx_Val_ChanForAllLines));
DAQmxErrChk (DAQmxStartTask(taskHandle));
DAQmxErrChk (DAQmxWriteDigitalU32(taskHandle,1,1,10.0,DAQmx_Val_GroupByChannel,&data,&written,NULL));
taskHandle=0;
DAQmxErrChk (DAQmxCreateTask("",&taskHandle));
DAQmxErrChk (DAQmxCreateDOChan(taskHandle,"Dev1/port0/line0","",DAQmx_Val_ChanForAllLines));
DAQmxErrChk (DAQmxStartTask(taskHandle));
DAQmxErrChk (DAQmxWriteDigitalU32(taskHandle,1,1,10.0,DAQmx_Val_GroupByChannel,&data,&written,NULL));
I want to simply set "Dev1/port0/line7" and "Dev1/port0/line0" to high level, but only "Dev1/port0/line0" responds me. The second parameter of the function DAQmxWriteDigitalU32 corresponds to numSampsPerChan. If i replace it (currently 1) with a larger value, e.g. 100, I can see that "Dev1/port0/line7" sends a number of 1 out, then return back to 0. So I guess the problem is just that I do not understand well all parameters of the function DAQmxWriteDigitalU32. Can anyone please tell me how I can set a digital output line to 1 or 0?
Thanks!
Hongkun
Solved!
Go to Solution.

Hello,
Here is a link explaining the inputs of function:
http://zone.ni.com/reference/en-XX/help/370471W-01/daqmxcfunc/daqmxwritedigitalu32/
Also here you can find a lot of examples in ANSI C
http://www.ni.com/example/6999/en/
Randy @Rscd27@

HT1695 In case any Wi-FI is available and if I choose not to join wi-fi, on iPhone 5 it does not connect to my 3G cellular data network but it connects to 2G data network forcing me to lower speeds in Wi-Fi enabled ares

In case any Wi-FI is available and if I choose not to join wi-fi, on iPhone 5 it does not connect to my 3G cellular data network but it connects to 2G data network forcing me to lower speeds in Wi-Fi enabled areas.

This might help
http://support.apple.com/kb/ht3406

What are high and low values in sharepoint 2013 user permissions?

So I hit this api:
http://win-a3q7ml82p8f/sharepoint_site/_api/web/roledefinitions/
And got the different high and low values. But I am not clear with what they mean:
For eg:
High: 176, Low: 138612833
and
High: 176, Low: 138612801
So for different values of Low how does it change the permissions?
For 176 its binary is 10110000. So looking at this table here: http://www.dctmcontent.com/sharepoint/Articles/Permissions%20and%20Mask%20Values.aspx
I can understand that 176 would mean the following set of permissions:
DeleteVersions
OpenItems
ApproveItems
But what's confusing me is, that user has OpenItems permissions but not ViewListItems permission? Am I wrong in understanding this?
Also how does the value of Low change the overall user permissions?
Note: I looked at this answer: http://social.msdn.microsoft.com/Forums/sharepoint/en-US/9d6df168-e8f5-4323-8c34-0646c03eff68/rest-api-what-are-high-and-low-in-effectivebasepermissions-and-getusereffectivepermissions?forum=sharepointdevelopment
But honestly I cant understand what that means. Can someone help please?

check this blog may explain you...
http://jamestsai.net/Blog/post/Understand-SharePoint-Permissions---Part-1-SPBasePermissions-in-Hex2c-Decimal-and-Binary---The-Basics.aspx
Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem. ****************************************************************************************** Thanks -WS MCITP(SharePoint 2010, 2013) Blog: http://wscheema.com/blog

E3000 High strength, low speed

Similar Messages

Maybe you are looking for