E3200 not saving port forwarding settings

I have tried numerious times to set my port forwarding settings.  Everytime I setup and fill in the appropiate ports and hit the save button my setting are lost.  I go back into the port forwarding setting page and literally after a fews secondsof  inputting the ports and nothing is there and everything is zeroed out .  Has anyone experienced this problem.  Do I have to set my ip address to static before I can put my port forwarding settings in.

Yes to all.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Similar Messages

  • Linksys E1200 Router not saving Port Forwarding changes

    Hi!
    I am currently attempting to port forward on my Linksys E1200 Router and am not succeeding in saving my settings. I am attempting to open port 25565 though both Single Port Forwarding and Port Range Forwarding, and whenever I click the "save settings" button, I receive a full window message stating that my changes have been saved. Upon clicking this, I return to the previous screen whereupon my changes have been erased and my port has not been forwarded. Can anyone assist me with this? I've searched for hours through forums and tech help websites, but I can't find anyone else with this issue.
    Issue:
    Linksys E1200 Router not saving Port Forwarding changes.
    I have tried:
    -Restarting the Modem
    -Restarting the browser
    -Restarting the computer
    -Tried to Port Forward through both the Single and Ranged Port Forwarding

    Hi there. You can try another browser or a different computer. If it is the same thing, upgrade the firmware of the router. You can refer to this link on how to http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0a6881b90224439b92c8d8f19ca42e5d_21511.xml&pid=80&...

  • WRT54GS Not saving port forwarding info.

    I gave up on an older router, and had the wrt54gs sitting in my closet. I  had to set it up for the PSN and COD4, but everytime I enter the port forwarding info, it says its saved, but erases it.
    The info is:
    TCP 80
    TCP 443
    TCP 5223
    UDP 3478 - 3479
    UDP 3658
    All enabled on PS3s IP
    Click SAVE SETTINGS
    It opens a black window that says settings saved
    I click OK
    and everything has been erased. 
    Im on firmware 7.50.2.
    Ive tried both firefox 3 and internet explorer. (ff3 error console gave me no errors)
    DMZ is enabled for my PS3.
    Ive tried both a wired and wireless connection.
    I can use my PS3s browser (if that matters)
    Any suggestions?

    You need to Upgrade the Firmware on your router...Download the Firmware from here , Follow these steps to upgrade the firmware on the device: -
    Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
    Leave the username blank & in password use admin in lower case...
    Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
    Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
    Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router and do the port forwarding and check if it saves the settings...

  • Airport Extreme removes port forward settings every reboot

    I have set up various port forward settings on my Airport Extreme from OS X Server. However, every time I reboot the Airport, all port forward settings are lost except Contacts, Calendars, and DNS. It gets very troublesome to constantly readd all my settings in there. Port forwards are the only settings that are lost.
    Please help!

    I found the issue – and it's fairly simple and obviously really.  I'm guessing you were adding the ports from OS X Server in the order they are listed within Server.app (where they are listed in alphabetical order).  After Calendar, Contacts and DNS is "File Sharing".
    If this is enabled, whilst File Sharing is enabled on the AirPort Extreme, the port forwarding entry for File Sharing, and anything below is removed.
    Simply disable "File Sharing" from AirPort Utility before continuing (as recommended by Server.app when setting up the service for File Sharing).
    I understand you replaced your AE and no longer have the issue – I thought I'd leave the explanation should others encounter it.

  • WRT160Nv3 port forwarding settings not being saved

    Hello there.
    I am using a WRT160Nv3 router and am having trouble getting port forwarding to work. 
    Specifically, my settings are not being saved properly. 
    I am trying to set up a server to run for Minecraft, and I have eliminated all issues save port forwarding.
    I open up the router's settings by going to 10.10.10.1 in my browser.  I go to "Single Port Forwarding."  I then choose a blank spot on the left and label the application (in this case, Minecraft), then I type in the ports I want to forward (minecraft uses 25565).  I check the box "Enabled."  Then I go down to the "Save Settings" button below and click it.
    This brings me to a mostly black screen with a white box in it, and big black letters saying "Settings are successful" and a button to click, labeled "continue."  I click this, and it returns me to the last page I was on (Single Port Forwarding).
    But here is the problem- that page is EXACTLY the same as when I began.  None of what I typed in or changed is actually saved on the screen o_0
    This definitely baffles me, as it seems as if I did nothing in first place.  I use the program whose port I wanted to forward and it still doesn't work, the error messages being the same as always. 
    So what is the matter here?  Why aren't my settings being saved properly?  Do I need to get a new router-this one is only a year old...
    Any ideas?
    PS- I also tried to do port range forwarding, and the same thing happens there too.

    hi there and welcome to the forums!
    try to clear your browsers' cache..and delete cookies then try again

  • WRV210 loses port forwarding settings after reboot

    Along with wireless problems that have already been documented about this device I am having problems with port forwarding where it will lose all its settings after losing its power.  I then try to go into the management for port forwarding and am not able to put the settings back in as every time I hit 'Save' it just loads the page back up with no settings applied.  Another strange thing is that the protocol comboboxes only have options for UDP or Both. 
    I then reapply the latest firmware and am able to enter the settings again.
    Any help would be greatly appreciated as I'm at my wits end with this one.
    Thanks,
    Paul

    Dear Paul,
    Thank you for reaching the Small Business Support Community.
    If you are already running the latest firmware release version 2.0.1.5, all I can suggest you is to contact the Small Business Support Center directly to determine if this is a hardware related problem, notice this product is already End of Life/End of Support and therefore the support is subject to warranty or contract terms and conditions;
    https://supportforums.cisco.com/community/netpro/small-business/sbcountrysupport
    Please do not hesitate to reach me back if there is any further assistance I may help you with in the meantime.
    Kind regards,
    Jeffrey Rodriguez S. .:|:.:|:.
    Cisco Customer Support Engineer
    *Please rate the Post so other will know when an answer has been found.

  • Port forwarding settings don't last

    Hi I have a synology NAS I set up the port forwarding and all worked fine, confirmed open port 80, all OK
    All settings within home hub 2 have not been changed but now the NAS does not respond, and port 80 can no longer be seen  any ideas please

    There is a guide here.
    Port forwarding problems
    I assume that you are using a DDNS service to update your IP address, and you have manually configured a static IP address for the device on your LAN?
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • Cannot save Port Forwarding Settings

    I have a Wireless-N Home Router WRT150N (firmware upgraded to v1.01.9 ).
    When I try to set Port forwarding, I get the screen "Settings are successful. Continue". When I click Continue, the Port forwarding page comes back with empty fields, like if I did not enter anything. I tried to reset the Router twice. No result.
    The same thing happens for Port Range and Single Port forwarding... Impossible to save any settings in there...
    Any suggestion welcome...

    Correction: caching was not the problem.
    The problem was that before posting on this forum, I did not enter a existing IP for destination (left the default 192.168.1.0. What got me confused is that the Linksys interface comes up with a message saying that the settings have been successfully updated, even though nothing was done for lack of an existing destination IP, hence the virgin table served back.
    I think Linksys should revise the GUY to alert the user when the destination IP is not properly set rather than pretending to have registered a new non functional setting.
    Message Edited by lou_boumian on 01-12-2008 10:15 PM

  • WRT610N V1 will not allow port forwarding via HP Mediasmart Server

    I have the WRT620N router and an HP MediaSmart server connected to it.  My source is a cable modem.  WHen I try to set up the server for remote access, the router is not found.  I am continually getting "Port Forwarding failed" errors from the server.  I also have several iPhone apps used to control devices on the network (DVR, BluRay player,etc) that will not connect.  (These worked before I changed to this router.) 
    I have verified that the UPnP is enabled.
    I have been struggling with this issue for several months and have not had any luck getting help from the forums, but will tryi again.
    Any help would be appreciated.
    Thanks,
    Joel WZ
    Thanks,
    Joel WZ

    Did you tried to enable Remote Management Access on the router setup page?
    If no, then Enable Remote Management Access under Administration tab and then check.

  • Help please, with port forwarding settings

    I have an MSI RG60 wireless router (Ethernet hard wired to my XP Home PC) and don't know what settings to use for port forwarding, to enable my WinMX and BitTorrent clients to work successfully.
    I have the port numbers, and assume that this information goes in the Service Port box, i.e. 6699, or 6881-6889.
    I know which ports are TCP and which are UDP, but I don't know what IP address to enter or which Common Service Port type to choose. Can anyone help please?
    I'm pretty sure that other settings in my PC are OK as I have successfully been running a Belkin router for a couple of years, and have only replaced it with the new MSI unit due to reliability problems.

    It does indeed have port triggering, but it wants incoming and trigger port protocol info, along with trigger and incoming port numbers.
    How can I type ipconfig into either of teh clients...WinMx or Bit Torrent?

  • Is there a fix for SL not saving Logic Pro settings?

    Hi all, I am stuck in SL but don't mind that if there is a way to fix this problem of settings not being saved. I had the problem first in Mail,it refused to save my ISP Password and was fixed by a software update mentioned on this forum. Does anyone know if such an update for Pro apps was ever available? And is it still there for downloading?

    I commend your perserverance but 5.1 is newer than 7, that is what is posted in the above screen shot. Here are some things left over from attempting to install #7
    I know it seems strange, but it seems to be true,Jobs is turning in his grave. The screen shot in my previous post shows it even better,hard to read[too small] but it was a fix for just these things. Click on that image in post above and it will appear in a larger window,these small 2 ones will as well. It isn't even possible to trash that pref[plist] it restores its' self instantly,no time to install #7,and I trust developed to avoid that being done. The new Apple boss man no like Pro apps,only want to sell new hardware.

  • Ichat port forwarding settings

    Can someone point me to the open port settings for ichat? I cannot find them on the web and the hints and tips section above this forum says I do not have permission to read.
    There used to be a document with the UPD and TCP settings, they are the ones I want.
    Cheers

    See also my reply to Greg's post.
    Apple has two Articles on the subject both are shwon as the two first hits in a Google Search (iChat Ports)
    This was the 9th item http://www.ralphjohns.co.uk/iChatPicsFolder/6%20iChat%20Ports/index.html But I am baised.
    I may receive some form of compensation, financial or otherwise, from my recommendation or link.
    7:19 PM Sunday; November 8, 2009
    Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"

  • Sent items not saved -- delete accounts/settings/preferences

    I have mail accounts with AOL and Mobile Me. I understand that to save sent items on the server, I must use the setting "Mailbox > Use This Mailbox For."
    For both AOL and Mobile Me accounts, I successfully set up the sent items folders. Under the paper airplane icon, both are reporting "Contents stored on server. Namer on server: Sent."
    However, only the Mobile Me account is functioning properly. If I uncheck the mail preference "store sent messages on the server" for my AOL acconts, then Mail will store sent items locally in Mail.app, but this is not what i want.
    It is possible this is a problem with AOL. I have two AOL accounts, and they behave a little differently, so I think I have an issue with my settings or preferences. I'd like to know how to completely remove all mail accounts/setting/preferences from Mail.app. All my accounts are IMAP accounts, so I don't need to save anything that is stored locally.
    I thought I had removed all accounts/settings/preferences related to mail.app, but when I go to add an account, my AOL account info is already populated in the first screen, so I don't think I deleted everything.
    Thanks for any help with deleting preferences/settings related to mail.app.

    I have mail accounts with AOL and Mobile Me. I understand that to save sent items on the server, I must use the setting "Mailbox > Use This Mailbox For."
    For both AOL and Mobile Me accounts, I successfully set up the sent items folders. Under the paper airplane icon, both are reporting "Contents stored on server. Namer on server: Sent."
    However, only the Mobile Me account is functioning properly. If I uncheck the mail preference "store sent messages on the server" for my AOL acconts, then Mail will store sent items locally in Mail.app, but this is not what i want.
    It is possible this is a problem with AOL. I have two AOL accounts, and they behave a little differently, so I think I have an issue with my settings or preferences. I'd like to know how to completely remove all mail accounts/setting/preferences from Mail.app. All my accounts are IMAP accounts, so I don't need to save anything that is stored locally.
    I thought I had removed all accounts/settings/preferences related to mail.app, but when I go to add an account, my AOL account info is already populated in the first screen, so I don't think I deleted everything.
    Thanks for any help with deleting preferences/settings related to mail.app.

  • Logic Express 9 not saving transport bar settings

    I changed my transport settings by adding buttings and clicked the 'save as default' button, but the the settings do not stay when I quit logic and reopen the project file.

    Well,
    What I have to say is that the Roland's support helped me to find an answer. We tested the controller with another computer and everything was fine. The main problem was about software. When I formatted my computer almost everything was solved. The only problem that still remain is the midi oscillations in MIDI OUT display when ACT is lit. Now I can control LOGIC, and there is no strange advise when I start it. About the detail of the oscillations, maybe is a problem of configuration in LOGIC, maybe is a problem of hardware in my computer, I still don't know.
    I wrote this because if anyone in the world is in the same situation, who knows, these words could help in any way.
    Best

  • Camera not saving manual mode settings.

    As the title says, everytime I choose a scene mode and go back to manual mode the settings gets reset. (i.e. focus mode, ISO, metering mode)
    It is annoying to set it everytime. Why can't the app remember my settings.

    As far as I know this is how the phone is intended to work. Manual mode is intended to be used for a specific photo, and the settings is normally not preferred in other situations.
     - Official Sony Xperia Support Staff
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

Maybe you are looking for