E4200 Bridge Mode

Can someone please point out what I am doing wrong here.....
I have my main router, a E4200v2 which I use as a router and it provides wireless signal throughout my house, however reception is not as strong on the upper floor and there is a slight dead spot, so I purchased an E4200 for the uppermost floor.
I set the E4200 to bridge mode so it will act solely as an AP.
However connecting the two routers LAN to LAN and the AP does not access the internet
Setting a static IP for the router, instead of acquiring one via DHCP causes me to not be able to access the admin page on the AP.
Connecting WAN on the E4200 to the LAN on the v2 does not work either.
My goal here is to have my main router on 192.168.1.1 and the AP on 192.168.1.2 where I can access the admin settings for both routers in case I need to make changes.
Can someone point me in the right direction here.....
thanks,
Solved!
Go to Solution.

There are two (2) ways to cascade a Linksys router to another router:
1. LAN to LAN – Connecting one of the Ethernet ports (LAN ports) of the Linksys router (router A) to one of the Ethernet ports (LAN ports) of another router (router B).
This type of cascading requires the main and the secondary routers to be on the same LAN IP segment to allow the computers and other devices to connect to both routers. This configuration is recommended if you want to share files and resources within the network.
2. LAN to WAN – Connecting one of the Ethernet ports (LAN ports) of router A to the Internet port (WAN port) of router B.
This type of cascading requires the main router and the secondary router to have different IP addresses. This connection makes it easier to identify which router the computers and other devices in the network are connected to since they will have different LAN IP segments. However, computers that are connected to router A will not be able to communicate with router B, and vice versa since there are two (2) different networks.
Here is the link for the same: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=785463d9ecaf4cac84aed245b08d615f_3733.xml&pid=80&r...

Similar Messages

E4200 Bridged Mode - Wireless and Management fail after 36 hours

Greetings all,
I am trying to see if anybody else is having this problem. I have the E4200 and have it configured in bridged mode. Once configured, everything works great for 36 hours.
After 36 hours, all wireless devices are unable to pull an IP address and the management IP address of the E4200 stops responding. The only way to restore service is to reload the router.
I took the first one back to Best Buy and they gave me a new one, however the new router has the same issue.
It seems to me that after 36 hours, the E4200 fails to renew its management IP and also stops forwarding wireless broadcasts (DHCP) requests to my DHCP server.
Thoughts?

Thanks. The new E4200 firmware has "bridged mode" so basically I just have this thing acting as a Wireless access point that has 5 Gigabit ethernet ports.
This disables the routing engine in the E4200 and it acts as a wireless AP and switch. The E4200's WAN port then connects to a Gigabit switch located in my telco closet, which is connected to my FiOS Router.
Reason for this setup is so that devices connected to either the Gigabit switch, or to the E4200 via hardwire or wireless will all remain on the same subnet, and not cause the broadcasts to block as packets traverse subnets.

E4200 Bridge Mode + Guest Access?

Hi,
I'm trying to set up my E4200 in "Bridge Mode," but want to enable a few things in the wireless settings, such as:
a) choosing SSIDs and network keys,
b) enable Guest Access
I've been able to get things working without too much hassle:
* factory reset
* set wireless SSIDs and network keys
* enable guess access and set password
* turn on bridge mode
Everything is basically fine, except that when the device goes into bridge mode it seems that it shuts off *all* web UI. This kind of makes sense, but do I actually understand that correcty? (Or have I simply not found the right connection method?)
If so, it leads to a couple follow-on questions:
a) How do I disable Bridge Mode if I want to change any settings? (Is the answer just 'factory reset'?)
b) Can Guest Access mode work in Bridge Mode?
So far, I have not been successful in getting the device to display the login page for Guest Access. I'm not sure if that's a config problem with Guest Access or if that just doesn't work in Bridge Mode.
Any tips/advice appreciated.
thx

Dude buddy. This is your post:
gv
Expert
Posts: 11,833
Registered: 07-16-2006
0
Re: E4200 Guest Network Not Working [ Edited ]
06-24-2011 10:40 AM - last edited on 06-24-2011 10:41 AM
It's not possible to use guest access in bridge mode. Guest access is only possible when the E4200 operates as router. In bridge mode any wireless network goes directly into the same LAN. Guest separation would not be possible.
Also don't disable the SSID broadcast.
http://homecommunity.cisco.com/t5/Wireless-Routers/E4200-Guest-Network-Not-Working/td-p/406345/highl...
What I'm saying is that it is possible and that I am doing just that on our LAN here at work.
You pegged me on the linksys devices not allowing higher subnets. Alas, I am used to using DD-WRT and Tomato for years now (where you can use any subnet mask) and took for granted that I have not seen a stock linksys GUI in a long time. However, in bridge mode on the E4200 you are able to set subnet masks as you wish...

E4200 bridge mode question

So, with the latest firmware update I could add a second e4200 to my network to use as a bridge or access point? What I need is another device in my living room that can pick up the wireless signal and dish out network connectivity to my receiver, xbox360, and ps3. With the new firmware update can this be done with a second e4200?
How does one connect to each e4200 on the network for setup (dohave to change the default ip address of 1?)
I just bought a trendnet TEW-687GA 450 mb/s wireless gaming adapter and a trendnet 5 port switch to accomplish what I mentioned above. I'm just wondering if there is an advantage to switching over to two e4200's. The trendnet adapater does not have a 5ghz channel.
Thanks!

The bridge feature doesn't support wireless bridging. It just dumbs it down to a switch and AP. So unless you flash it with a 3rd part firmware such as dd-wrt, what you are trying to accomplish will be impossible.
I've heard multiple people say that 3rd party firmware for this router is buggy so I would either go with the trendnet and switch setup or the 5ghz capable Linksys WES610n. The 5ghz is ideal for for gaming and streaming media because of less interference compared to the 2.4ghz band. You'll more than likely be able to bond channels with the 5ghz network so that = more bandwidth.
I don't work for Cisco. I'm just here to help.

E4200 guest wireless redirect failure in Bridged Mode: cause & solution.

Background:
I have two E4200 v1 routers, both running the 1.0.04 firmware, both running in Bridged Mode.
On one, guest wireless redirect works perfectly: select the Network-guest SSID, open a browser and you get the Cisco login page, enter the passphrase and bingo, you're connected.
On the other unit, the redirect seems to fail. You are never presented with the login page and so, you are never connected.
After hours of mucking about, including some time on the phone with a very patient engineer, I believe I have stumbled on what's actually going on and possibly, what needs to be done to fix it.
The Problem
The firmware assumes that in Bridged Mode, DNS should come from the Gateway IP address.
The Fix
Linksys should include a field in Bridged Mode that allows you to specify an IP for the DNS server.
Diagnostics
To diagnose the problem, I used a Mac OS X machine.
The network is set up like this:
Router (not the E4200) is at 10.0.0.1
DNS server is at 10.0.0.2
E4200, Bridged Mode as a WAP, is at 10.0.0.253.
E4200's network settings are:
IP: 10.0.0.253
Subnet: 255.255.255.0
Gateway: 10.0.0.1
The problem is that the Linksys firmware assumes that DNS and the gateway are at the same IP. You will note that there is no place in the Bridged Mode settings to specify a DNS server IP address. You can prove this by doing the following:
1. Connect to the guest wireless.
2. In a Terminal window, type cat /etc/resolv.conf and press Enter. You'll see this:
nameserver 10.0.0.1
nameserver 192.168.33.1
This tells us that when you're on the guest network, your machine is looking for DNS results from 10.0.0.1. Except that on many networks, the gateway does not supply DNS. You can prove that DNS is working by typing this into a Terminal window:
dig yahoo.com
You should see a result similar to this:
; <<>> DiG 9.6-ESV-R4-P3 <<>> yahoo.com
;; global options: +cmd
;; Got answer:
;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 45182
;; flags: qr rd ra; QUERY: 1, ANSWER: 3, AUTHORITY: 13, ADDITIONAL: 13
;; QUESTION SECTION:
;yahoo.com.           IN   A
;; ANSWER SECTION:
yahoo.com.       3063   IN   A   209.191.122.70
yahoo.com.       3063   IN   A   72.30.38.140
yahoo.com.       3063   IN   A   98.139.183.24
;; AUTHORITY SECTION:
.           24651   IN   NS   a.root-servers.net.
.           24651   IN   NS   j.root-servers.net.
.           24651   IN   NS   l.root-servers.net.
.           24651   IN   NS   c.root-servers.net.
.           24651   IN   NS   e.root-servers.net.
.           24651   IN   NS   d.root-servers.net.
.           24651   IN   NS   f.root-servers.net.
.           24651   IN   NS   m.root-servers.net.
.           24651   IN   NS   g.root-servers.net.
.           24651   IN   NS   b.root-servers.net.
.           24651   IN   NS   i.root-servers.net.
.           24651   IN   NS   h.root-servers.net.
.           24651   IN   NS   k.root-servers.net.
;; ADDITIONAL SECTION:
a.root-servers.net.   24651   IN   A   198.41.0.4
b.root-servers.net.   24651   IN   A   192.228.79.201
c.root-servers.net.   24651   IN   A   192.33.4.12
d.root-servers.net.   24651   IN   A   128.8.10.90
e.root-servers.net.   24651   IN   A   192.203.230.10
f.root-servers.net.   24651   IN   A   192.5.5.241
g.root-servers.net.   24651   IN   A   192.112.36.4
h. root-servers.net.   24651   IN   A   128.63.2.53
i.root-servers.net.   24651   IN   A   192.36.148.17
j.root-servers.net.   24651   IN   A   192.58.128.30
k.root-servers.net.   24651   IN   A   193.0.14.129
l.root-servers.net.   24651   IN   A   199.7.83.42
m.root-servers.net.   24651   IN   A   202.12.27.33
;; Query time: 73 msec
;; SERVER: 10.0.0.1#53(10.0.0.1)
;; WHEN: Thu Apr 5 10:51:02 2012
;; MSG SIZE rcvd: 494
Note the section at the bottom that says ;; SERVER: 10.0.0.1#53(10.0.0.1). This tells you that the DNS query was answered by the DNS server at 10.0.0.1.
But in fact, if DNS is NOT served by your Gateway, you'll see this:
dig yahoo.com
; <<>> DiG 9.6-ESV-R4-P3 <<>> @10.0.0.1 yahoo.com
; (1 server found)
;; global options: +cmd
;; connection timed out; no servers could be reached
Lucky:~ aball$
As a side note: the reason that the login page is never presented is most likely that the login page is only presented the first time that your Mac OS X machine connects to the network. Thereafter, the network is remembered and the WAP allows you access without a password. So, once you've connected a second time to the network, the WAP says "I know you" and lets you sail on through to wherever your browser is pointed, but then the browser, unable to find a DNS server, returns a blank page which appears to be a failure to present the login page but is, in fact, a DNS failure.
Hope someone finds this useful. And here's hoping that Linksys fixes this obvious issue with the firmware.

I do understand what you were trying to do here since you would like to have only 2 SSIDs (main & guest) for perhaps easy connectivity. The reason why you were not having problems getting online wirelessly when you were connected to the main network it’s because the computer was connected to only one DHCP server since the 2 bridge routers were just acting as a switch or a passthrough device. Now with guest network access it is a different scenario, a guest network is a virtual network meaning to say it’s like your having another router embedded on your router. Since it is a virtual network, then it does not follow the parameters of the main network, hence even if the router was set to bridge mode those routers will still have their own ip address of either 192.168.33.1 or 192.168.3.1.

E4200/E3200 in bridge mode...Guest access works, but does not roam between routers...any ideas?

I have installed wireless in my church...main router is E4200 in the office set up as follows:
IP: 192.168.0.1
Subnet: 255.255.255.0
DHCP enabled (Range = 192.168.0.4-192.168.0.103)
Guest network enabled
Static DNS (for content filtering)
NAT: Enabled
Second router E3200 (in bridge mode) - connected LAN to WAN
IP: 192.168.0.2
Subnet: 255.255.255.0
Guest Network enabled
DHCP (obviously disabled)
Static DNS (for content filtering)
NAT: Enabled
Third router E3200 (in bridge mode) - Connected LAN to WAN
IP 192.168.0.3
Subnet: 255.255.255.0
Guest network enabled
DHCP (obviously disabled)
Static DNS (for content filtering)
NAT: Enabled
The 2 routers in Bridge mode are connected to a 16-port unmanaged switch (with other PCs, etc.), which is then plugged into the main router in Port 1.
SSIDs on all 3 routers are exactly the same for both main and Guest networks.
The main network works flawlessly. The router in the office hands out IPs in the 192.168.0.XX range and you can wander throughout the church and maintain a persistent Internet connection. File and print access works fine too from anywhere in the building.
For the Guest network, you can set up a laptop next to each router, obtain an IP address, reach the logon page and surf the Internet without issue. So, the Guest Network works fine from each router.
However, if you wander around the church while on the Guest network (such as with a smart phone), the following happens:
-On either of the E3200 routers (in bridge mode) you get the login page as you wander into the range of each router. I would have thought that if you logged in once, you would be good to go.
-You get a different IP from each router. On the E3200's in Bridge mode, you get a 192.168.33.XX address. Additionally, the gateway is 192.168.33.1. On the E4200 (main router) you get a 192.168.3.XX IP and a gateway of 192.168.3.1.
-As a result of getting different IPs, the smart phone becomes confused and generally won't connect to the Internet.
So, it looks like each router maintains a separate list of who has entered the correct password to get onto the Guest network. Additionally, it appears as if each of the 2 routers, supposedly in Bridge mode, is still handing out IP addresses on the Guest Network, rather than deferring to the router in the office like they do for the main network.
I have seen a lot of postings about how to put routers into Bridge mode and problems with the Guest Network, but posts that I've seen point to the Guest network not working at all, as opposed to this issue where it works; the bridged routers, though, continue to like to hand out IP addresses on it, making wandering around the church while connected to the Internet not possible while connected to the Guest network.
Anyone else experience as similar situation? Any possible solutions out there?
Thanks!
-Gil
Solved!
Go to Solution.

I do understand what you were trying to do here since you would like to have only 2 SSIDs (main & guest) for perhaps easy connectivity. The reason why you were not having problems getting online wirelessly when you were connected to the main network it’s because the computer was connected to only one DHCP server since the 2 bridge routers were just acting as a switch or a passthrough device. Now with guest network access it is a different scenario, a guest network is a virtual network meaning to say it’s like your having another router embedded on your router. Since it is a virtual network, then it does not follow the parameters of the main network, hence even if the router was set to bridge mode those routers will still have their own ip address of either 192.168.33.1 or 192.168.3.1.

Can I use multiple E4200's in bridge mode, to enable a "guest wifi' mesh?

I have four E4200 units on my network, each with an unique IP address, in bridge mode to act as a wireless mesh across my entire building. They are all connected to my central L3 switch, via their Internet ports.
Is it possible to enable the Guest network on each unit, to create a 'Guest Wifi' mesh (providing that I allow the 192.168.33.0 network to route across my network fabric), or will this not work because each indivudual AP will be assigning IP address 192.168.33.1 as it's gateway address meaning that I would have four distinct MAC addresses within the network, each trying to claim that they are IP 192.168.33.1?

As soon as you enable guest access on the router, it will start providing the IP address 192.168.33.x to the clients connecting to the guest network and we cannot change the IP address range of guest network.
Since you have 4 units (E4200), you can enable guest wi-fi of each of them however cannot create a guest wi-fi mesh as all the 4 units have different IP address.

E4200 limitations in Bridge Mode

Hi,
My setup goes like this: I have a Fiber to Ethernet connector from my ISP. The Ethernet cable goes to an iSP issued Zyxel router. Into this router the landline phoneservice connects to give us VoIP landline service (which is cheaper). An Ethernet cable goes from the Internet port on the E4200 to a LAN port on the Zyxel router. That works great but I had to put the E4200 into Bridge Mode to get it to connect to the Internet via the Zyxel router which I need to use the phone services my ISP provides.
I bought the E4200 because I wanted to use the dualband functionally and get a 802.11N 5GHz network setup and to give me the ability to block certian websites and services which I knew Cisco/Linksys is famous for - the abillity to control your network.
Well then imagine my surprise when I could not use the Parental Control settings when the router is in Bridge Mode... This was the reason I bought this router over an Apple Airport Exreme. Is there anyway to get it to let me use the Parental Control anyway while in Bridge Mode or a better way for me to connect the router with the rest of my network?
Thanks for any help!
Solved!
Go to Solution.

If you don't have any devices (primarily gaming devices) which require an open NAT, then you can connect an ethernet cable from the Zyxel router to your E4200's Internet port and just use it like a normal router without bridge mode.
Just make sure the E4200's ip address is on a different subnet (Just change the third octet (number in the third decimal place) to something other than the one used as the Zyxel's default IP.
You could call your ISP and ask them how to dumb down the Zyxel so that you can use the E4200 as the primary router and the Zyxel as a modem too.
I don't work for Cisco. I'm just here to help.

E4200 as a Access Point/Bridge Mode

I have spent most of the weekend trying to get this router to act as a proper Access Point.
Has any got this to work correctly?
When it does work (Stay connected) speeds and latency are rotten. If I go back to Routing Mode this thing kicks butt, but I isolate all devices attached to a different subnet and trying to set up proper routes has proved imposable.
Firmware 1.0.2 r 13
The online help stated to connect to the "internet interface" when in Bridge Mode DHCP Server Is not broadcasting to on the wireless or wired interfaces.
If I used the wired interface as the uplink I can broadcast the DHCP to any device on wired but again nothing to the Wireless.
When I "Show Routing Table" I see two static routes pointing to the ATT router for the Wired/Wireless Interfaces.....
0.0.0.0 255.255.255.0 (my Gateway) Wired/Wireless
(my Gateway) 255.255.255.0 0.0.0. Wired/Wireless
Why??
AP mode should only be working in Broadcast.
By connecting the Wired Interfaces alone up to my switched network should not use the router at all.
If you force all traffic to my router all traffic has to be inspected by the firewall
You create a bottleneck my router interface is 10/100.
ATT 2 Wire Gateway/Router with pinholes. 10/100/1000 Non managed 24 port Switch Network. Server infrastructure serving DNS/DHCP.
I decided to buy this after reading it offered Bridge/Access Point mode instead of getting the WAP610 because I wanted to have the option to change to routing mode or AP mode.
Since my ATT Uverse Router Wireless is “g” it takes forever to transfer files to and from my servers.

OK If this helps... I am running a SOHO
2Wire DSL Router with DHCP Off Assigned 192.168.100.1 as the Router Gateway IP. NAT Enabled All firewall is being handled via 2Wire. Currently 2Wire WiFi is disabled. For the Linksys E4200
2wire 10/100 interface up-linked into my d-link 24 port 10/100/1000 Layer 2 unmanaged switch.
DHCP and DNS Servers on d-link switch
VOIP on d-link switch
Testing Results WAN Interface Bridge
E4200 up-linked via 10/100/1000 Internet Interface to d-link network switch.
E4200 Internet Interface DHCP assigned using MAC Reserved DHCP 192.168.100.22.
E4200 in Bridge Mode
Devices connected to 4X E4200 Gig Ports do not receive DHCP broadcast IP Address
Device Connected to E4200 WiFi do not receive DHCP BroadcastIP Address
Assign Static IP to my laptop WiFi in the 192.168.100.X range will establish communication but HUGE latency and poor speeds for any traffic internet or internally to any of my servers.
At times the connection gets lost.
In this configuration I get the above stated Route Tables.
If this is layer 2 compliant it should be handing all local subnet traffic via MAC instead of routing.
I have not taken the time to attempt to reconfigure my 2Wire to go into DMZ Plus mode and allow the linksys to handle all routing, but from previous attempt with my wrt54 it did not go well. I accepted the slow 2Wire WiFi speeds.
It is now getting to the point I am looking for better WiFi to local LAN speeds , I also am looking to do Layer 2 and bypass Routing if I can.
The WAP160 has a 10/100 interface. I prefer gig

E4200 not connecting with Cradlepoint CBR450 set to bridge mode

I am trying to replace my Cradlepoint MBR1200 with a CBR450 in bridge mode, to let the E4200 take over all the WAP and DHCP handling, but having a hard time.
I set the CBR450 in bridge mode and when I connect it to my laptop it properly passes the IP info to my Mac and allows me to connect. I then connect it to the E4200 WAN port with it set to get IP address automatically but nothing ever happens and I am never allowed traffic in/out over the WAN.
I *can* get internet access by leaving the CBR450 in normal mode (handling DHCP, etc) and then plugging it into the E4200 LAN port and having the E4200 set to bridge.
Any ideas why the E4200 WAN port is not getting the bridge info and allowing connection? FWIW, works fine connecting to a DSL modem with the DSL model set to bridge mode at my other house.
CBR450 and E4200 both on latest firmwares.

When you configure/edit the Primary Lan on the CBR450 to IP pass through mode, change the lease time under DHCP Server tab to something very low, like 2 minutes. When in pass-through mode, the CBR450 still assigns the IP address from the aircard directly to the ethernet interface, but uses DHCP to do this. Sometimes when connecting to Cisco devices, it helps when the lease time is set this low.

E4200 in bridge mode

Hi,
The latest firmware seems to support bridge mode. Does it mean the router can connect to another router wirelessly in the bridge mode?
Solved!
Go to Solution.

No, it bridges the LAN and WAN ports allowing E4200 to downgrade to an access point.
I don't work for Cisco. I'm just here to help.

E4200 Locks Up in Bridge Mode

I'm using the E4200 in Bridge mode and it's handing out IPs from our DHCP server (not acting as it's own). I have about 8 people connecting to this wirelessly to get to our network. For some reason it locked up once every week or two and I have to unplug it (can't even remote into it). Any ideas?

Do the following steps:
A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
          1] Open the software and go to the option which says "Router Settings"
          2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
        3] Lower the MTU (Maximum Transmission Unit) from 1500 to 1400 or less (usually found on your router's main/ basic setup page)..
B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.
Then check the connectivity status..

E4200v2 Bridge Mode + Guest Access: No DHCP IP's assigned?!

New E4200v2 on 2.0.37. In "Bridge Mode - DHCP" (i.e. Access Point not router). Guest Access is enabled & SSID broadcast. Dhcp Server is disabled, because my main Sonicwall router is providing that for main LAN 192.168.1.0.
PROBLEM = Client PC can see "-guest" SSID fine and associate to it, BUT PC does NOT receive a DHCP IP address (i.e. 192.168.33.x) therefore the browser login page never appears and guest access does not work.
I'm pretty sure that it's all related to DHCP. I'm assuming that the E4200 is not receiving or sending guest DHCP packets with the client PC.
I seen Guest Access work on the older E4200v1's before so I know what it should look like.
Can anyone suggest any likely reasons why my E4200v2 wouldn't be providing DHCP guest addresses in the 192.168.33.0 subnet?
I only have 24 hrs until I have to deploy 2 new E4200v2's at a remote site, and after that it's going to be really hard to troubleshoot because I won't be at that site.
Thanks in advance for any expert advice!
Solved!
Go to Solution.

When you're in bridge mode DHCP server option goes away. And I don't care if DHCP requests are getting to my Sonicwall b/c that device is not going to assign the Linksys Guest IP's... E4200 must do that, apparently in a totally hidden way.
In any case, I don't have any more time to waste on E4200v2's so I'm going to try some E4200v1's which I just happen to have handy, thankfully.
If Bridge Mode + Guest Access works better on the V1's then I'll retreat back to that older more obsolete hardware.
I'll report back later.
(In meantime if anyone else cares to offer their knowledge experience about this, V2 or V1, I'm all ears)
gv wrote:
Do guests get an IP address if you enable the DHCP server?
Do you see guest DHCP requests on your sonicwall?

AC1600 (EA6400) In Bridge mode

My AC1600 (EA5400) is setup in Bridge mode, all is working correctly except that on the main router which is a Linksys 4200 it will not acknowledge the parental settings, on the EA5400 I only have 3 options Conectivity, Troubleshooting and Wireless. on the 4200 the same 3 settings are plus Device List, Guest access, Parental Controls, Media Prioritization, Speed test, external storage and security. I am sure if I cascade the routers I will have the options but will have to maintain the Parental Controls on both, is there a setting a am missing that will not allow the Parental settings to work?

What Parental Controls settings are you trying to do? And which router are trying to set the Parental Controls? If the EA6400 is on Bridge mode, it will have limited settings since most of the settings will only work when on Router mode. I agree on using EA6400 as the main router and cascade the E4200 as an access point. Set the Parental Controls settings on the EA6400.

Bridge mode on E1000?

The E4200 has a bridge mode (or switch mode). But I can't find if my E1000 has a bridge mode too. And when "yes": how can I install it?

Hannelore80 wrote:
The E4200 has a bridge mode (or switch mode). But I can't find if my E1000 has a bridge mode too. And when "yes": how can I install it?
This router does not support bridge mode. However, you can cascade it to your main router and would work the same way as bridge mode. Follow the LAN to LAN instructions below:
Cascading or Connecting a Linksys router to another router

E4200 Bridge Mode

Similar Messages

Maybe you are looking for