E4200 - Configure guest access

In my neighborhood, people generally allow open WiFi access to each other. The "guest access" feature of this router sounded good - you can allow guests to access the internet, without allowing them access to your own computer's transmissions. However, annoyingly, there is no way to configure guest access without a password. You can change the password, but guests have to come see you and ask you what the password is. No freedom to configure the router the way I want. Sending it back for a refund.

Well, if you have configured the router manually or even with the Cisco Connect you cannot disable the open security mode for the guest network. A password will have to be entered after launching a web browser.
The secured mode of the Guest Network cannot be disabled and will always require your guests to enter a password through a web browser. The prompt will appear everytime guests connect. This is to prevent unauthorized Internet access.

Similar Messages

  • Configuring Guest Access using 2 LWAPs and 2504 WLC

    Please advise,
    I have 2 APs, Cisco Aironet 1040, and 2504 WLC.
    Is it possible to configure guest access (Guest SSID/VLAN and Corporative SSID/VLAN) without dedicated guest WLC in DMZ?

    Yes you can. You can have up to 16 SSIDs per AP, but not suggested to have all 16. You can either use one port on the 2504 for both SSID/vlan or specify which port is for corporate and which one is for guest.
    Thanks,
    Scott Fella
    Sent from my iPhone

  • E4200 Wireless Guest Access issue

    Hello, I'm hoping someone can point me in the right direction. I have the wireless guest access set up in my E4200 flash to the latest firmware. 
    When I connect to the wireless guest network it comes up under the 192.168.33.xx IP address. I can connect fine but it never pops up the browser so that you can type in the guest password. I'm running Windows 7 but I've also noticed the exact same problem under XP.
    The only thing I can guess is the problem is that I have this acting like an access point and all DHCP requests go to my router. I've basically turned off DHCP on this and plugged the network connection into the switch on the back. 
    Any suggestions?
    Thanks
    Josh

    If I go to 192.168.33.1 it does pop up the browser but when I enter the password It just hangs. Not sure if it was connected or not. Is there no way to pop up the browser automatically?

  • Guest Access - Easy creation of Guest-Vouchers

    Hi
    I have previous used WCS together with my WLC 2504 to create guest-users.
    Employees in the corporation can through their AD-Credentials log into WCS, and create guest users for the Wifi-Network.
    The WCS solution for creation guest users is however to complicated and many users choose to call our helpdesk insted of self-service. Other users create guest accounts and set them to never-expire, I then manually have to clean up in the never-expire accounts later..
    We have 20 departments arround the contry, some bigger than others and therefore we don't have an reception in every department. Every employee should therefore be able to create guest-accounts themselves.
    I've tried to use "Captive Portal" by Pfsense but it just issue a lot of vouchers there need to be printed and distributed to the departments, its a kind old-fashion.
    The optimal solution would be a internal website where employees can log into. Here they could type their guests mobilephone number, and a 8 hour voucher wold be send by sms. Easy and end-user friendly.
    Another solution could be a website that create an 8 our voucher with one-click and then print the voucher (insted of sms)
    In WCS the users have to choose add-user - profile - controller list - expire time - etc etc before the login is created...
    Can anyone recommend a good solution for this, not to expensive. We don't got guest that often.
    Best Regards, Steffen.

    ISE have rich Guest management features built in to it. ISE guest services enable you to provide secure network access to guests such as visitors, contractors, consultants, and customers.Cisco ISE provides web-based and mobile portals to provide on-boarding for guests (and even employees) to your company’s network and internal resources and services.
    From the Admin portal, you can create and edit guest and sponsor portals, configure guest access privileges by defining their guest type, and assign sponsor privileges for creating and managing guest accounts.
    Check the following link for more information
    http://www.cisco.com/c/en/us/td/docs/security/ise/1-3/admin_guide/b_ise_admin_guide_13/b_ise_admin_guide_sample_chapter_01111.html

  • How-do-i-configure-guest-wifi-access-using-2504-wlc-fortigate-utm-l3-device

    Dear All
    I have a 2504 Wireless Controller with multiple radios attached. I currently have a "private" WLAN configured (taking ip from windows server based DHCP of Range 192.1681.0/24 ) and working, but I need to add a Guest/Public WLAN which should take the IP from Other DHCP Configured on Fortigate UTM of range 172.16.0.0/24.
    We have one SG300 switch in the office and the rest are basic switches.
    Our firewall/router is a Fortigate UTM 240D
    Find the attached network diagram for the issue.
    Is there a SIMPLE way to enabling guest access that doesn't require VLANS (or are VLANS easier than I'm making them)? 
    Thanks.
    - See more at: https://supportforums.cisco.com/discussion/12473186/how-do-i-configure-guest-wifi-access-using-2504-wlc-fortigate-utm-l3-device#sthash.aj1XcWI0.dpuf

    Complete these steps in order to configure the devices for this network setup:
    http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/70937-guest-internal-wlan.html
    Configure Dynamic Interfaces on the WLC for the Guest and Internal Users
    Create WLANs for the Guest and Internal Users
    Configure the Layer 2 Switch Port that Connects to the WLC as Trunk Port

  • E4200 Bridge Mode + Guest Access?

    Hi,
    I'm trying to set up my E4200 in "Bridge Mode," but want to enable a few things in the wireless settings, such as:
    a) choosing SSIDs and network keys,
    b) enable Guest Access
    I've been able to get things working without too much hassle:
    * factory reset
    * set wireless SSIDs and network keys
    * enable guess access and set password
    * turn on bridge mode
    Everything is basically fine, except that when the device goes into bridge mode it seems that it shuts off *all* web UI. This kind of makes sense, but do I actually understand that correcty? (Or have I simply not found the right connection method?)
    If so, it leads to a couple follow-on questions:
    a) How do I disable Bridge Mode if I want to change any settings? (Is the answer just 'factory reset'?)
    b) Can Guest Access mode work in Bridge Mode?
    So far, I have not been successful in getting the device to display the login page for Guest Access. I'm not sure if that's a config problem with Guest Access or if that just doesn't work in Bridge Mode.
    Any tips/advice appreciated.
    thx

    Dude buddy. This is your post:
    gv
    Expert
    Posts: 11,833
    Registered: 07-16-2006
    0
    Re: E4200 Guest Network Not Working [ Edited ]
    06-24-2011 10:40 AM - last edited on 06-24-2011 10:41 AM
    It's not possible to use guest access in bridge mode. Guest access is only possible when the E4200 operates as router. In bridge mode any wireless network goes directly into the same LAN. Guest separation would not be possible.
    Also don't disable the SSID broadcast.
    http://homecommunity.cisco.com/t5/Wireless-Routers/E4200-Guest-Network-Not-Working/td-p/406345/highl...
    What I'm saying is that it is possible and that I am doing just that on our LAN here at work.
    You pegged me on the linksys devices not allowing higher subnets. Alas, I am used to using DD-WRT and Tomato for years now (where you can use any subnet mask) and took for granted that I have not seen a stock linksys GUI in a long time. However, in bridge mode on the E4200 you are able to set subnet masks as you wish...

  • E4200 guest access won't ask for pasword

    Hi whenever i enable guest access, when connecting though any device it doesn't ask for password but allows access straight away. I've tried changing the password, but no luck. Any ideas?

    yep... The guest network comes out as "Unsecured" but you need to obtain the Guest network password for you to be able to browse the internet. 
    "Don't fix it if it ain't broken."

  • E4200 Guest Access to Printer?

    The Guest Access is a very nice feature for allowing us to provide Internet access in our rental unit.
    However, it would be nice to provide the Guests access to the USB printer.   
    Is there a way to provide access to the USB printer for those who are logged into the "Guest Network"?

    Nope... Guest network provides internet access only and there's no way computers in the guest network can communicate with other computers within the guest network as well. 
    "Don't fix it if it ain't broken."

  • 2504 with new-architecture enabled breaks MAC auth for guest access

    Hello,
    We have (2) 2504 WLC running version 7.6.120. WLC1 is the local controller and WLC2 is an achor controller for guest-access. We need to incorporate a 3850 for use with the WLC2 anchor. The guest access is currently working with Mac-Auth and Mac-Auth-Fail to Web-Auth.
    When converged access is enabled on the WLC1 and WLC2, the MAc-Auth no longer works. That is, the previously authenticated user is now redirected to the Web-Auth page. The local controller shows the user as authenticated but the Anchor controller shows the state as WEb-Auth-REQD.
    Rolling back using "config mobility new-architecture disable" and rebooting resolves the issue.
    Does anyone what changes from the old to the new that would break this mac-auth/web-auth configuration?

    You should reach TAC for these sort of issues. Not many people deploying this CA setup yet & you may not get direct feedback immediately.
    HTH
    Rasika

  • How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

    How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

    The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
    If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

  • HOW TO CONFIGURE GUEST NETWORK AND LIMITE BANDWIDTH

    Dear all,
    Please help me how to configure internet access rule and limited the bandwidth for guest network via TMG Forefront 2010.
    Thanks you & best regards,
    Hung Viet 

    Hi，
    First you can create the new network set which is mapped to guest subnet, after that you can create access rule for this network set.
    If you want to control bandwidth, you may need 3-party tool like this:http://www.bsplitter.com/
    Best Regards
    Quan Gu

  • Wireless guest access

    Hi Guys, I have a wireless requirement from a customer and the customer is looking for the below: 1. Wireless guest access that requires user to input email into the captive portal. But the email address must be verified that it contains certain selected domain names (e.g. example.com or example.org). Any other domain names will be rejected. 2. Customer is looking to add their own logo and change the formatting of the captive portal. Questions: 1. For email verification, does this feature come straight from the WLC standalone box or must ISE be purchased? 2. If the WLC is able to do this without ISE, any online guides that is able to do this? 3. For security reasons, am I able to limit the number of concurrent users using this captive portal? 4. How do a configure the age-out for each connected users after they have successfully logged into the captive portal? 5. Can I customize the captive portal page on the WLC and how do I go about doing it?

    Hi Mohanak,
    It looks like the formatting ran out. Anyway, not sure if we are on the right topic here but let me get this straight. Customer has a Cisco 2504 Wireless LAN Controller. So, they would like to achieve the below features:
    1. Wireless guest access that requires user to input email into the captive portal. But the email address must be verified that it contains certain selected domain names (e.g. example.com or example.org). Any other domain names will be rejected.
    2. Customer is looking to add their own logo and change the formatting of the captive portal.
    So, some of the questions I have are:
    Questions:
    1. There is a configuration on the WLC that allows guest users to login using email verification only. Does this feature come straight from the WLC standalone box or must ISE be purchased.
    2. If the WLC is able to do this without ISE, is the WLC able to check if the inputted field is a valid email? And can I configure in such a way a particular domain is allowed? (e.g. example.com is permitted but example.org and anything else is reject).
    3. For security reasons, am I able to limit the number of concurrent users using this captive portal?
    4. How do a configure the age-out for each connected users after they have successfully logged into the captive portal?
    5. Can I customize the captive portal page on the WLC and how do I go about doing it?

  • Wireless guest access with CWA and ISE using mobility anchor

    My team is trying to demo wireless guest access using CWA with an ISE server.  We appear to be hitting an issue when combining this with mobility anchoring.
    When we don't use a mobility anchor the authentication goes off without a hitch seemingly proving that the ISE configuration is sound.  The test laptop associates and gets redirected, auths, moves to the RUN state and access to the network is granted.
    When the mobility anchor is enabled, the test laptop does get redirected, authentication is successful, but the process does not fully complete, as on the foreign controller the user is in RUN state whereas on the anchor the user is still stuck at CWA required.
    Now, I've read the L2 auth occurs between the foreign controller and ISE, and the L3 auth occurs between the anchor controller and ISE, but this does not appear to borne out in packet captures of the process where both parts of the auth seems to go to and from the foreign controller and ISE.
    I'm curious to know if anyone else has come across this issue, or has ideas where I should be looking in the config or debugs to find the root cause.
    When setting up the controllers and ISE this guide (linked below) was used and the controllers are 2504 controllers on 7.5 series software and ISE is on the latest 1.2 patches:
    http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml
    To me it seems to be mobility related, but the authentication flow does seem to be off compared with what the guide says.

    FOREIGN
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Adding mobile on LWAPP AP 0c:d9:96:ba:7d:20(1)
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Association received from mobile on BSSID 0c:d9:96:ba:7d:2f
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Max Client Trap Threshold: 0  cur: 0
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Re-applying interface policy for client
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4565 setting Central switched to TRUE
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4568 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying site-specific Local Bridging override for station 00:1e:c2:c0:96:05 - vapId 1, site 'AP-Group-CHEC.default', interface 'management'
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying Local Bridging Interface Policy for station 00:1e:c2:c0:96:05 - vlan 84, interface id 0, interface 'management'
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfProcessAssocReq (apf_80211.c:7830) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Idle to AAA Pending
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station:  (callerId: 20) in 10 seconds
    *radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created for mobile, length = 253
    *radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created in mscb for mobile, length = 253
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Received SGT for this Client.
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Redirect URL received for client from RADIUS. Client will be moved to WebAuth_Reqd state to facilitate redirection. Skip web-auth Flag = 0
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 255 to 255
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 84
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Re-applying interface policy for client
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 0 on mobile
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
    MAC: 00:1e:c2:c0:96:05, source 2
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Initializing policy
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state AUTHCHECK (2)
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfMsAssoStateInc
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
    *DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
    *DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
    *DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0,  mobility state = 'apfMsMmQueryRequested'
    *DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
    *DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
    *DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0,  mobility state = 'apfMsMmQueryRequested'
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=ExpForeign, client state=APF_MS_STATE_ASSOCIATED
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 apfMsRunStateInc
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) Change state to RUN (20) last state DHCP_REQD (7)
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Reached PLUMBFASTPATH: from line 5793
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Adding Fast Path rule
      type = Airespace AP Client
      on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
      IPv4 ACL ID = 255, IPv6 ACL ID = 255,
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 84, Local Bridging intf id = 0
    *mmMaListen: Jan 28 23:05:02.363: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
    *pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x4
    *pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 0.0.0.0 plumbing in FP SCB
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP processing DHCP REQUEST (3)
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 5, flags: 0
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   requested ip: 10.130.98.8
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP received op BOOTREPLY (2) (len 320,vlan 84, port 13, encap 0xec07)
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP processing DHCP ACK (5)
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 0, flags: 0
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0,  yiaddr: 10.130.98.8
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   siaddr: 10.30.4.173,  giaddr: 0.0.0.0
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   server id: 1.1.1.2  rcvd server id: 1.1.1.2
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) DHCP Address Re-established
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Reached PLUMBFASTPATH: from line 6978
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
      type = Airespace AP Client
      on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
      IPv4 ACL ID = 255, IPv6 ACL ID
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 84, Local Bridging intf id = 0
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 Assigning Address 10.130.98.8 to mobile
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP successfully bridged packet to STA
    *pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
    *pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4
    *pemReceiveTask: Jan 28 23:05:03.890: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 10.130.98.8 plumbing in FP SCB
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Received SGT for this Client.
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 0 to 255
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 AAA redirect is NULL. Skipping Web-auth for Radius NAC enabled WLAN.
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
    MAC: 00:1e:c2:c0:96:05, source 2
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Applying cached RADIUS Override values for mobile 00:1e:c2:c0:96:05 (caller pem_api.c:2307)
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Applied RADIUS override policy
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
      type = Airespace AP Client
      on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
      IPv4 ACL ID = 255, IPv6 ACL ID
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 84, Local Bridging intf id = 0
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Change state to RUN (20) last state RUN (20)
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfMsAssoStateInc
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 3600, apfMsTimeOut '1800' and sessionTimerRunning flag is  1
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station:  (callerId: 49) in 3600 seconds
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 3600
    *apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
    *apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
    *pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
    *pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4

  • ISE - Guest Access (without portal)

    Hi Guys,
    I have a customer who current is using the cwa portal for guest access. Corporate use will be added in the future sometime next year.
    Kit involved:
    5508 - Internal (Inside Net)
    5508 - Anchor (DMZ Net)
    ISE - Inside Net
    3600 APs
    Presently, guest user connects, anchored to DMZ 5508, issued IP address from server in DMZ and DNS redirect to the web portal from same server. guest logs in and internet access through ASA and then content filtering box.
    They want a solution whereby they do not have to use the portal for corporate user with their own devices such as ipads. I know BYOD is a possiblity but would involve using a CA server on the inside of the network. This is not something I'm keen as it opens a channel from the guest network directly to their AD infrastructure.
    I'm leaning toward PEAP authentication atm using a GoDaddy SSL cert that is already installed. This would bypass the portal system and only involve client devices being configured once.
    Is there any other option that would be simple to setup as this is on a limited timescale ?
    Cheers,
    Nick

    Nick,
    They want a solution whereby they do not have to use the portal for  corporate user with their own devices such as ipads. I know BYOD is a  possiblity but would involve using a CA server on the inside of the  network. This is not something I'm keen as it opens a channel from the  guest network directly to their AD infrastructure.
    If you are referring to supplicant provisioning, the scep enrollment request is proxied from ISE and the private key and cert is transferred to the endpoint. This doesnt require your guest network having direct access to AD....just to ISE.
    Tarik Admani
    *Please rate helpful posts*

  • Wired guest access with 5508

    Hi
    I have setup wireless guest access for a customer with a single 5508 and web authentication no problem at all. He then wanted to test wired guest access. The 5508 is currently connected to a single 3560 switch. The wired clients get a DHCP address OK but cannot reslove DNS and thus don't get redirected to teh guest login portal. I have even tried turning of all L3 security to no avail. The setup is as follows
    VLAN 101 access points and 5508 management interface
    VLAN 102 wired guest access dynamic ingress (L2 config only no SVI on 3560)
    VLAN 103 wireless guest dynamic egress nterface L3 network with SVI on switch
    VLAN 104 wired guest dynamic egress interface L3 network with SVI on switch
    There are two DHCP pools setup on the WLC one for the VLAN 103 and one for the VLAN 104 subnets.
    The internet router is also connected to the 3560 on a sepearte VLAN with an SVI. the 3560 has a default route to teh internet router and teh DHCP pools give the DHCP clients a default gateway of the IP address of dynamic interface 103 or 104. The Internet routre can ping the WLC on both these addresses.
    LAG is enabled on teh WLC and VLANs 101-104 are trunked to it from the 3560.
    I even tried making the wired guest egress interface the same one as for wireless. The wired clientys now got an IP address on the wireless range but still couldnt pass any traffic. It's like the intrenal bridging on teh WLC between VALN 102 and 104 (or 103) is broken. Tried both the lates 6.x and 7.x software on the WLC. Any ideas ? All the problems I can find with this seem to relate to not gettingas far as a DHCP address but that works fine.
    Thanks
    Pat

    Hi
    Yes got it resolved. It turns out that the connection from the wired guest access port to the WLC must be L2. That is the switch that the wired guest acces sport is connected and WLC are connected to must be L2 only. We were using a single switch to do the testing and it was also doing the routing for the test LAN. Even though there was no L3 VLAN interface configured for the VLAN that the guest access port was on for some reason this breaks it. Absolu Didnt have chance to work out the exact limitations of this as we simply made the switch L2 only and configured an 802.1Q trunk to the Internet router and made subinterfaces on the router for the wired and wireless egress ports and it worked then. No config change was needed on the WLC at all.
    The only thing I can think of is that it's something about the way the WLC joins the wired guest access ingress VLAn and egress VLAN. The WLC isn't a reall router it says so in the documentation. I think the packet coming from the wired access port is being bridged to the egress VLAn not routed and this is what screws it up (remeber with a router the source and destination MAC addresses would be changed with a bridge they aren't). Got to be something along those lines. If you have a bigger newtork with a guest anchor WLC handling this function you dont run into this as the traffic is coming over an EOIP tunnle from the remote WLC so the switch with the guest anchor WLC doesnt see the MAC address of the wired guest PC.

Maybe you are looking for

  • [AS] How to make cross reference at insertion point

    Hi, I have a book ("indb") including several documents with several "anchors" (german translation: "Textanker") where cross references from different documents are linked to. What I already got is to reference all anchors and collect them in a list.

  • Unable to download newest episode with seasonpass

    I purchased the season pass for prison break season 4 a month ago but am unable to download episode 7. when i click on check for check for available downloads it says that there are none. episode 7 just came out and I do not have it in my library. Th

  • How  to  stop  putting    between  every  word?

    My +imac +just +started +doing +this. +I +am +using +lion. +Maybe +it +is +a +keyboard +falt, +but +then +it +wouldnt +put +them +before +each +word +it +would +do +them +randomly. Any +ideas +how +to +stop +this +nonsense?? Yeah +right. +this +isnt

  • Home laser printer printing questions

    Hi, I want to by a laser printer for home. Heed help from those who have experience: I have local network, so I can either use USB with print server or network printer. I found that CUPS drivers are required for network printing (print server) in OS

  • Sales Value in Credit Management

    Hi Gurus, I've set a credit limit for a customer using FD32 and the sales value field in the status group, is not updating.  the receivables, and credit exposure is updating but the sales value is not.  How can I activate it?  Why is it not updating?