E4200 connection dropped once homeplug connected

HI,
I just installed a E4200, and found that once I connected my Homeplug Powerline to E4200, the connected (wired / wireless) computer (with E4200) connection will be dropped. The connection become normal again once I disconnected the Homeplug with E4200.
Here is the error description from Cisco Connect: An HNAP call to the device failed because the HTTP connection was broken.
Does someone know what is going on? I will appreciate any comments & replies.
Many thanks!

There might be some settings required in the router so that it gets the proper solution. If you are facing the concern of getting lag, dropped connections then you can try the following steps:
A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
1] Open the software and go to the option which says "Router Settings"
2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
3] On that same setup page reduce the MTU value to 1400 from Auto
4] Then go to the Wireless tab, keep network mode as mixed,
For Channel Settings of 2.4 GHz you can make Channel Width to 20 MHz only and Channel to 6, 9, 11..
For Channel Settings of 5 GHz you can make Channel Width to 20 MHz only and Channel to 40 or 161...
B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.

Similar Messages

Has anyone else had an iPhone 5 that's only been dropped once accidentally and smashed the screen? Mine has done that and as I don't have mobile insurance it'll cost a fortune to replace it through Apple!!

Has anyone else had an iPhone 5 that's only been dropped once accidentally and smashed the screen? Mine has done that and as I don't have mobile insurance it'll cost a fortune to replace it through Apple!! I don't think the phone is fit for purpose as any other phone i've had has been dropped and been fine and surely they expect a mobile to be accidentally dropped at least once!!

Yeah, sad to hear of your accident:
If you dropped it on concrete- that is the hardest material and chance of damage goes up tremedously. Actually you are fortunate not to have mobile insurance because then you have to trust your insurance provider to provide you with a quality replacement or repair.
Apple is always spot-on you know what you're getting. They can always attempt to replace JUST the display on an iPhone 5 for $149 + tax is what I've heard them quote others. But they said it's $229 to replace your phone with another whole new iPhone 5. Get the AppleCare+ because two of these incidents will only cost you $49 + tax in the future!

HT201364 Is ther any performance drops once OS X Mavericks is installed on Late 2008 Macbook (Aluminum Unibody)?

Is ther any performance drops once OS X Mavericks is installed on Late 2008 Macbook (Aluminum Unibody)?

I just installed it on mine last night and noticed that the fans basically don't stop running when I have any programs running...Pretty disappointed in that, but hoping something will make it go away.

E4200 v2 - Dropping wireless connection

I purchased this router as an upgrade from my Cisco/Linksys E3000 that I have had for over a year. I use wireless almost exclusively in my household and when the E4200 V2 is working it is great but then it seems to slow down. Actually it is not slowing down but dropping packets on the wireless segments after varying periods of time. The wireless connection does not drop ( i used vistumbler to view the connection in real time ) but all connections exhibit dropped packets. I had Amazon send me a replacement and it did the exact same thing. I even restored the router to default and setup just the wireless connection both using the Cisco connect and the web interface and the problem still happens. To test this I set a constant ping of the router's gateway address on my WLAN and observed 25% to 40% dropped packets. After a reboot it is more stable, but it becomes more unstable over time. The wired connections are solid and did not drop any packets but wireless is a joke!

There are many reasons why you experience poor signal or connection. Your intermittent wireless connection has a relation to the kind of setup that you have in your home or office. Is the connection dropping on all wireless computers or just one?
You have mentioned, you set the router to factory defaults and re-configured it. Did you try changing the channel on the router to either 1, 6, 9 or 11? There could be an interference with other wireless devices in the network (cordless phone, microwave etc.) since they work on the same frequency.
Try this and see if that helps.

E4200 Constantly Drops Connections (Wired and Wireless)

My E4200 seems to be dropping connections throughout the day. For wireless it'll still show full signal and connection, but there will be no internet activity for about a minute. Then after a minute things will work just fine again.
For wired I notice it in my XBox mainly when I get dropped from games as constant as the wireless drops.
I believe my modem isn't the problem since the old router never dropped connections on the hard wired devices. Occasionally my old D-Link router would drop wireless, but never this frequent
I am running 1.0.02. I've rebooted the router/modem several times. I even reinstalled the entire setup with the current version of Cisco Connect as the tech person suggested, but still no help. The first week or so using this router was flawless, but ever since then it's been dropping connections several times throughout the day to any device connected (wireless or wired). The problem seems that the router just hiccups the connection very quickly, so quickly that Windows doesn't even recognize the connection has been lost, but long enough to drop a multiplayer game on XBox or to have me mashing refresh on my internet browsers.
Does anyone have any ideas?

I have not had this problem with my router and have had it since Feb 2011. I did have a range extender from WNR2000RPT Netgear that I had to reboot everyday and finally threw it away and bought the Linksys RE1000. The combination is flawless in my 3000sqft. house. I will say though it may have to do with your setup and what channels you are on. I have my router setup just for wireless and not as a DHCP server and let my FIOS router handle DHCP. Just so I am not running 2 seperate networks in the house. I also gave my E4200 a static IP as well as the Range Extender static IP. So there would not be IP address conflicts that could cause for possible issues. I did have a problem with the latest firmware disabling my USB for my external hard drive so I had to downgrade to resolve that issue.

SRP521 Lan connections drop once wan is connected

I have had this issue on the last 3 srp521's I deployed, all were pulled from service and replaced with a different model. Firmware is 1.1.24 and I also tried on with 1.1.27
With only power and 1 lan connection I start a ping to the router and a ping through it to the DG of the wan ip. When I plug in the wan cable I get a single reply from the wan ip DG and then my lan connection drops. I have to power cycle the router to get it to come back. I have a static set on the WAN and am using 10.10.10.x on the lan side. The link light on the router stays on for both lan and wan.
Any idea on what to look at?

Hi Sage,
I'm not sure that I follow what you mean when you say the WAN goes down as soon as it is connected. Could you provide more detail please? Can you specify what address you are using for the WAN and LAN (with masks).
Also, I'm not sure what you mean by:
I plugged it into the its own switch and it went down as soon as connected
Regards,
Andy

E4200 router dropping connection

I have e4200 router and i notice sometimes when i am browsing that dops connection.
how would i check this and what should i be looking at to fix this?
Any info would be appreciated.

Changing channels is one of the best ways to resolve intermittent wireless connection through the router and there's really no fix type of channel, they all depend on all devices in your entire network. You may refer to the link provided by jlbjlb about the inSSIDer to help you find a none-overlapping channel or one that is not very commonly used. 5GHz and 2.4GHz are two different wireless frequencies so for as long the other is not on the same range than the other then it should be good.

E4200 - Connection issues

V1 has had so many problems for me I probably won't be getting the V2.
Well, people in the house can usually not connect to it, and if they do, they don't get internet. I have a booster router (also Linksys) that takes the E4200's signal and creates a third wireless network, and that one works fine with all the computers. I'm plugged directly into it, and the internet gives about 99.9% uptime, so it's not that.
I got the E4200 at Bestbuy because I had a faulty E3000 that overheated and sporadically dropped connections, and they didn't have any of those in the store so they gave us an E4200.

I'm having problems with my download speed normally it's 62 Mbps I got extreme connection the best there is and 3.15Mbps upload speed. My problem is I play lots of games online and every day before I play I check my connection speeds download and upload because it seems to effect my game play every thing becomes very slow some days I just can't play at all because it lag so much got this router cause I thought it would help my problem! I call my internet provider and we did some speed test and there modem works fine speeds r 60mbps download upload 3.15Mbps plug back into E4200 router and it drops to 10,8,2 maybe once or twice have I seen it at 62Mbps I pay for extreme connection and it feels like I have phone line what the hell is going-on with this router? I just did speed test and again it is at 14.69Mbps download and upload is what it should be. 3.15 without router I get 62Mbps with router 10-8-6Mbps cannot play like that to much lag!! No matter what sever I go in I've tried resetting, unplugging does not help had E300 before and it never drop pass 22 and I thought that was bad but now with E4200 it's worst how can this be? Even late at knight when people r sleeping it still does not go up to 62mbps cannot play bf3 its hearts me man too much lag my settings in game r on low its does not help and I have crossfire 5970 and eyefinity fx8150 processor at 4.8Ghz h100 corsair liquid cooler only once in a while it's at 62Mbps So can some one tell me why? This happens? And how can I fix it? Every day it's the same problem! I update driver same thing

E4200 connect with Sony KDL-46EX701 at 2.4 Only

My E4200 does not connect with my Sony KDL-46EX701 at 5 GHz. The set sees the 5 GHz at medium strength or highter, but won't connect. Password is correct and verified. The Sony's UWA -BR100 adapter should work at 5 GHz, and it did work with my E3200 at 5GHz (unfortunately, it also caused the tv to recycle off and on whether connected at 2.4 or 5GHz).
2.4 works fine with the E4200 and the Sony.
Problem occurs with 1.0.0.1 firmware and 1.0.0.2 firmware.

As my first post mentioned, I've been there and done that to no avail.
I also tried a Netgear WNDR4000, with the same result.
I've noticed that the 5 GHz reception on the Sony looks weak/unstable. I think the problem is that Sony's UWA-BR100 stick has poor reception, particulary at 5 GHz. Worked ok in winter and spring, but even indoors w/AC and good ventilation, my usable wireless range has always dropped significantly in summer when it's hot and humid.
Anyway, I gave up. I took and Linksys E3000 that I was going to return, installed TomatoUSB on it, set it up to be a wireless ethernet bridge, disabled the 2.4 GHz radio, and then wired it to the Sony. Then I manually configured the IP settings on my Sony TV. With the E3000 as a wireless bridge, the E4200 and the Sony connect perfectly at 5 GHz. Expensive fix, unfortunatly.

E4200 - connection speed slow

Have E4200 has been running 6 months. Have it now installed in my new home and it was so fast in download and upload with Cox Preferred. It has slowly been loosing it punch wirelsss I hit 1.5 to 8.5 download by ethernet 8-10 really slow especially when we were hittin over 21 on download slowest was over 18. What do I do I can't buy another especially after spending $175 is it defective?

There are many reasons why you experience slow speed or connection. Well, there are few things you should keep in mind with regards to N routers:
•    Wireless Channel
The default setting for most Linksys Gateway is either Auto or Channel 6-2.437 GHz.
QUICK TIP: For Wireless-N Dual Band-Routers/ Gateway, it is best to use 20 MHz when in a 2.4 GHz or 5 GHz populated area to avoid wireless interference. For less crowded networks, you can use 40 MHz on a 5 GHz. If you’re unsure, you may leave channel width at Auto. This will automatically adjust the settings to 20 or 40 MHz, depending on which best fits your network.
If you are selecting the 5 GHz wireless network, ensure that your wireless devices and adapters have a 5 GHz capability for selectable dual-band. Otherwise, do not change the frequency of your router.
•    Wireless Security
It is the encryption method used to protect a wireless network from intruders. For best wireless-N performance, encrypt your router with WPA2-AES.
After configuring your Gateway with these settings, make sure that all wireless devices are in sync with the Gateway‘s wireless configuration. Also, place the wireless Gateway on an elevated spot and away from other devices that may cause interference.
•    Wi-Fi Multimedia (WMM) is a wireless Quality of Service feature that should be disabled.
•    Make sure the drivers for the Wireless Card for the computers should be updated as well..

Linksys e4200 connection reliability issues

Hello there. A few months ago, I bought a new Linksys E4200 and it had no issues, until now. Recently, the reliability of this thing has dipped. The connection would just stop working and I'd have to unplug the box and reboot it. Other times, the Cisco logo would start blinking and the connection would stop, then it'd fix itself. But today, both things kept happening over and over to the point where I had to switch to the Netgear router that Comcast provided me with (which is working perfectly). As a mine craft server runner, I rely on a constant, reliable connection. What should I do? The e4200 is still faster than the Netgear thing so I'd like to get it fixed.

TheCh1ckenM7n wrote:
I'll give it a shot.
Just provide updates. I hope it will work.

E4200 connected devices

I've used Netgear & other routers for years; I was able to see the devices connected over ethernet & wifi through the router configuration utility. Cisco's interface looks poor; there is no way to see the connected devices.
Many of the devices I have have a 5 Ghz radio and some don't so i need to see at what speeds they are connecting at.
Or does Cisco not provide this utility? I am surprised that a high-end product from Cisco does not have this function.
Solved!
Go to Solution.

hiptechboy wrote:
192.168.1.1 ---> Status--->Local Network---DHCP Client Table doesn't work for you?
holly crap I never knew that DHCP!! button was down there , thanks so much. Sorry linksys I take back what I said about this particular thing.
please fix the E4200 media server in .02 firmware

E4200 Connection issues with two Samsung Blu-ray players at a time

Hi everybody,
Sorry about my English,
I have E4200 V1 router, it is working fine, and I am connecting different type of devices with it like desktop computer, laptop, iphone, printer and two Samsung 3d smart Blu-ray players. Everything is working fine. I have charter cable internet.
But the problem is this: when I play movies via Netflix on both Samsung Blu-ray players (one player is in my family room and second player is in up stare bedroom) one player stopped playing movie and disconnected from the wireless network and message shows (check your wireless network).
When I stopped/turn OFF the second Blu-ray player, then the first one got connected with network and start playing movies.
I can’t run both Blu-ray players at the same time on this E4200. When I was playing both players at that time all the other devices I mentioned above was connected with the same network but were not performing any task, those were in sleeping mode.
I also changed the QoS, Quality of Service setting to high priority using MAC address for both players, but it is still not playing both Blu-ray players at the same time. Just one plays the movies at a time.
Any idea or help to solve this issue, I would really appreciate that.
Thanks,

Hi, chzsoona. Have you tried changing the channel of your wireless channel? You may try channels 1, 6, 9, 11. If you have a version 1 router, check your firmware version it should be 1.0.05. If you have version 2 router then you may upgrade it then use Linksys Smart WiFi so you can take advantage of the Media Prioritization. To know more about your router you may use this link: http://kb.linksys.com/Linksys/ukp.aspx?pid=80&app=vw&vw=1&login=1&json=1&docid=7824947fe4444ac3ad5cc...

E4200 - wireless drops out

I am disappointed with the Linksys E4200 and E2500. Both had wireless issues with it dropping out. The Cisco connect was a nice feature, but the problems started when it wanted to update. I have gone back to the tried and true WRT54GL. I recommend that people should wait a year till Cisco fixes the problems.

The performance of your new router depends on various factors apart from the router itself. The wireless devices in your network, are they wireless G or wireless N devices? If they're wireless G devices, you won't really see any difference, and in fact any N devices in your network would also suffer because of that. Apart from that, placement of the router also matters.
Avoid keeping the router in a corner or under the table or something like that. Ideally you'd want to keep it at a higher location. The signal always travels better from a higher location to a lower location. Apart from this, you can also change channels on the router. Typically, wireless interference can cause poor signal strength and speed. Changing channels helps alleviate this problem to some extent. I'd suggest trying channels 1, 3, 6 or 9. You'll have to try each and observe which channel gives you the best performance. Every network environment is different, so what works for one network may not necessarily work for another. Please let me know if you need any further help with this.

UCCX 7 Call gets dropped once agent picks up

I have been troubleshooting a problem for a few weeks now where calls are being dropped as soon as the agent picks up the call. This is happening to various agents happening a few times per day everyday. I have done a reactive debug on the script and it seems to go through to the end ok yet everytime an agent reports a call drop as soon as they pickup, i see the following in the MIVR logs. I have checked the CSS/Partitions of all the CTI ports also.The CCM traces and Q931 traces show normal call clearing:
215269973: Apr 21 14:53:42.306 GMT %MIVR-APP_MGR-7-STEP_FAILURE:Failure to execute a step: Application=App[name=switchboard,type=Cisco Script Application,id=50,desc=switchboard,enabled=true,max=10,valid=true,cfg=[ApplicationConfig[schema=ApplicationConfig,time=Wed Jan 06 16:44:49 GMT 2010,recordId=67,desc=switchboard,name=switchboard,type=Cisco Script Application,id=50,enabled=true,sessions=10,script=SCRIPT[Switchboard.aef],defaultScript=,vars=null,defaultVars=null]]],Task id=30000147369,Step id=198,Step Class=com.cisco.wf.steps.ivr.TerminateStep,Step Description=Terminate (--Triggering Contact--),Exception=com.cisco.contact.ContactInactiveException: Contact id: 32425, Contact is inactive when getting channel
215373932: Apr 21 15:03:50.012 GMT %MIVR-LIB_EVENT-3-DISPATCH_FAILURE:A failure occured while dispatching an event: Event=com.cisco.call.CallEvent[CALL_ANSWERED,state=CALL_ANSWERED,contactImplId=3672150/2,lastContactImplId=3672150/2,session=Session[id=001-0x55ae8a4c1,parent=null,active=true,state=SESSION_IN_USE,time=1271858629996],lastSession=Session[id=001-0x55ae8a4c1,parent=null,active=true,state=SESSION_IN_USE,time=1271858629996],contactSeqNum=0,lastContactSeqNum=0] on CallContact[id=32462,type=Cisco Agent Call,implId=3672150/2,active=true,state=CALL_ANSWERED,inbound=false,handled=false,locale=en_US,aborting=false,app=null,task=null,session=Session[id=001-0x55ae8a4c1,parent=null,active=true,state=SESSION_IN_USE,time=1271858629996],seqNum=0,time=1271858629996,cn=null,dn=null,cgn=6664,ani=null,dnis=null,clid=null,atype=UNKNOWN,lrd=null,ocn=null,odn=null,uui=null,aniii=null,ced=null] at Wed Apr 21 15:03:50 BST 2010,Event source=CallContact[id=32462,type=Cisco Agent Call,implId=3672150/2,active=true,state=CALL_ANSWERED,inbound=false,handled=false,locale=en_US,aborting=false,app=null,task=null,session=Session[id=001-0x55ae8a4c1,parent=null,active=true,state=SESSION_IN_USE,time=1271858629996],seqNum=0,time=1271858629996,cn=null,dn=null,cgn=6664,ani=null,dnis=null,clid=null,atype=UNKNOWN,lrd=null,ocn=null,odn=null,uui=null,aniii=null,ced=null],Event listener=com.cisco.wf.subsystems.rmcm.ICDContactAdapter@50add0,Exception=java.lang.ClassCastException: java.lang.Integer
215375195: Apr 21 15:03:55.715 GMT %MIVR-APP_MGR-7-STEP_FAILURE:Failure to execute a step: Application=App[name=switchboard,type=Cisco Script Application,id=50,desc=switchboard,enabled=true,max=10,valid=true,cfg=[ApplicationConfig[schema=ApplicationConfig,time=Wed Jan 06 16:44:49 GMT 2010,recordId=67,desc=switchboard,name=switchboard,type=Cisco Script Application,id=50,enabled=true,sessions=10,script=SCRIPT[Switchboard.aef],defaultScript=,vars=null,defaultVars=null]]],Task id=30000147532,Step id=208,Step Class=com.cisco.wf.steps.ivr.OutputStep,Step Description=Play Prompt (--Triggering Contact--, WelcomePrompt),Exception=com.cisco.contact.ContactInactiveException: Contact id: 32461, Channel id: 52, Contact is in Terminated/Connected state
I do not have experience with scripting so if anyone could point me in the right direction that would be appreciated,cheers.

Reviewing the MIVR logs you provide I'm not sure which call your talking about. I see 2 calls with exception messages in the time stamp your saying.
First call:
Apr 22 11:49:11.621 GMT %MIVR-SS_TEL-7-UNK:CallID:33466 MediaId:3673987/2 Task:30000153869 com.cisco.jtapi.CiscoRTPInputStoppedEvImpl received
However this call is dropped as per the Jtapi message that the disconnect came from the CCM side however I can see that this call was never assigned to an agent so there should be no miss calls.
As for the second call, I don't have the full picture, as we don't have the offered message of when the call arrives to the system.
Here is a break down of the other call.
Call transferring to assigned agent:
Apr 22 11:49:07.308 GMT %MIVR-SS_RM-7-UNK:RIMgrAddressCallObserver: CallCtlConnInitiatedEv received for call 37228421 [3673989/2] and agent AylwardM
System changed call/agent states to answered/talking
Apr 22 11:49:07.308 GMT %MIVR-SS_CM-7-UNK:AgentCallContact 33468 and implId 3673989/2 moved to Answered state
We now see the exception message:
Apr 22 11:49:07.308 GMT %MIVR-LIB_EVENT-3-DISPATCH_FAILURE:A failure occured while dispatching an event: Event=com.cisco.call.CallEvent
However if you look futher down the call is connected to the agent successfully and in a talking state.
221901300: Apr 22 11:49:15.387 GMT %MIVR-SS_RM-7-UNK:RIMgrAddressCallObserver.callChangedEvent():
CallCtlConnEstablishedEv 3673989/2
Unknown event3673989/2
221901301: Apr 22 11:49:15.387 GMT %MIVR-SS_RM-7-UNK:RIMgrAddressCallObserver: CallCtlConnEstablishedEv received for call:37228421 [3673989/2], address 6656, calling party 6656, and called party 01923821368
Call Dropped as it recieve a disconnect event.
221902844: Apr 22 11:49:24.621 GMT %MIVR-SS_RM-7-UNK:RIMgrAddressCallObserver: TermConnDroppedEv received for call 37228421 [3673989/2] and agent AylwardM
The problem with the above call is that you don't see the CallCtlConnEstablishedEv till 7 seconds later, which is why I suspect you get the exception error, as it never got confirmation the call was delivered.
So my concern here, is if you stated you had a issue with calls getting dropped on the UCCX I would agree and ask you to provide CCM/Jtapi logs from the UCCX.
However you stated that your agents are getting miss calls on their IP phone, I disagree with this point as per the analysis performed.
"One question, when the CTI port is ringing the agent's phone to then transfer (reserved state) that call to that agent and the caller hangs up before the agent answer it, does the agent will hear a fast busy tone because that is what the CTI port transfer at the end to the agent? Am I right? if this is it I think there is no way to control this from the UCCX perspective, right?
Gabriel"
This senario will never happen, as the call would be terminated the moment the other party drops.

E4200 connection dropped once homeplug connected

Similar Messages

Maybe you are looking for