E4200 guest access won't ask for pasword

Hi whenever i enable guest access, when connecting though any device it doesn't ask for password but allows access straight away. I've tried changing the password, but no luck. Any ideas?

yep... The guest network comes out as "Unsecured" but you need to obtain the Guest network password for you to be able to browse the internet.
"Don't fix it if it ain't broken."

Similar Messages

Downloaded Photoshop 11 to move to a new computer. Download wouldn't accept the password and now won't ask for one. Now what?

I wish to install Photoshop 11 on my new computer. From My Products I received my password, after the download was opened the password was rejected and now it won't ask for it. Message..program is in use or I'm not authorized. How do I solve this?

If this is a Mac then it might be the Mac security asking for a password rather than anything to do with Adobe.

My 5s won't ask for password to connect to Wifi

I got my iPhone 5s today, went back to my office and tried to connect to my WiFi. It asked for my password, I input it incorrectly, it notified me of that, kicked me back out, and now when I re-try to connect to my WiFi it finds it, I try to connect, and it tells me it fails without ever asking for the password. I obviously cannot get in without the password so if it never asks I am locked out.
I have re-booted both the router and the phone, nothing. Still won't ask for the password. Just got through with loading the software update IOS 7.0.0.1 and no help. Any ideas?

Click on the exclamation mark next to the network that you want to change the password. Then click on Forget This Network. Go back and turn WIFI off, then back on. Your network will again appear and when you connect you will be asked for a password.

HT6114 my hot mail account will not let me access it keeps asking for password but won't authorise it?

my hotmail account will not open. keeps asking for password but will not accept the password when i enter it. its the correct passwrd?

Hello Duncan,
Thank you for the details of the issue you are experiencing with Mail on your Mac. I recommend the following steps for the issue you described:
If you entered the correct password in the password dialog in Mail, but continue to be asked for your password, try these solutions.
Open Keychain Access, then locate and delete the mail account password item.
Open Disk Utility, select the volume (for your hard disk or disks) in the list, click First Aid, then Verify Disk. After you’ve verified (and repaired, if necessary) the disk, try sending yourself a message.
Mail (Mavericks): If Mail keeps asking for your password
http://support.apple.com/kb/PH14935
I recommend continuing with the following article if the issue persists:
OS X Mail: Troubleshooting sending and receiving email messages
http://support.apple.com/kb/ts3276
Thank you for using Apple Support Communities.
Best,
Sheila M.

E4200 Guest Access to Printer?

The Guest Access is a very nice feature for allowing us to provide Internet access in our rental unit.
However, it would be nice to provide the Guests access to the USB printer.
Is there a way to provide access to the USB printer for those who are logged into the "Guest Network"?

Nope... Guest network provides internet access only and there's no way computers in the guest network can communicate with other computers within the guest network as well.
"Don't fix it if it ain't broken."

I have just restored my ipod touch after being disabled. Now it is asking for pasword, can I cancel this so I don't have to use a password?

I have just restored my ipod touch after being disabled. Now it is asking for the passcode? I still cant remember the passcode. How do I go past this?

You'll have connect in recovery mode and set it up "as new ipod" http://support.apple.com/kb/HT1808
If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone and iPod touch software.
If the issue continues after updating and restoring your device, refer to this document.
copied from http://support.apple.com/kb/HT1212

E4200 : Guest Access : No IP-address on cascade routers

configuration :
2 E4200 wireless routers.
LAN-LAN connected through a cable.
router 1 is connected to internet and has DHCP enabled.
router 2 is NOT connected to the internet and has DHCP disabled.
wireless is enabled on both of them with the same SSID.
guest account/access is both enabled on them.
this works :
laptop connects at normal WIFI on router 1 --> internet works (IP: 192.168.1.150)
laptop connects at normal WIFI on router 2 --> internet works (IP: 192.168.1.150)
laptop connects at Guest WIFI on router 1 --> internet works (after login screen in Internet Explorer) (IP: 192.168.33.108)
this does NOT work
laptop connects at Guest WIFI on router 2 --> internet does NOT works
--> laptop does not get an IP-address
when I connect to normal Wifi on router 2, I get an IPaddress from the DHCP on router 1
But when I do the same with the GUEST WIFI on router 2 it does not ask an IP-address at Router 1
anyone ideas????
thanks
Solved!
Go to Solution.

can you please tell me.
what IP address you are getting
on the laptop which is connected to the guest network
through the 2nd router and what is the range of the ip address.
that you are getting.

E4200 Guest access without password

With the E4200, is it possible to setup the main SSID with a passpharse but have the guest SSID without a passpharse or password (ie access without security). If so, How?

Theres no way to remove the guest password without disabling the guest network.. Best is to make it simple like "guest" or "1234".
The Search Function is your friend.... and Google too.
How to Secure your Network
How to Upgrade Routers Firmware
Setting-Up a Router with DSL Internet Service
Setting-Up a Router with Cable Internet Service
How to Hard Reset or 30/30/30 your Router

FTP for Guest with no password asks for password

Greetings,
I have File Sharing turned on and FTP on, and Guest login and sharing on in Accounts.
When I enter ftp:// and my IP in a browser, I get prompted for a User Name and Password. I enter Guest and no password, and it says Password Required, but there is no password.
How do I connect as Guest?
Thanks

what is your router model number?
so all this time you never set a password for your wireless network? @_@

HT5569 my iphone 4 won't ask for a password there is no prompt for me to enter my wifi details despite the wifi address coming up on the list ...

Please help! My partner has taken my old phone but we cant get it to join our wifi network a home - it wont request or prompt for the password...My iphone 4S works and joins the same network so it must be within distance to the router...we cant work it out.
Can anyone suggest what to do. We have turned on and off the router, the phone, and checked most things. It lists the locked wifi network but the message says ' Unable to join network'.
Many thanks

Hello cwestnutt,
Thank you for the details of the issue you are experiencing with Wi-Fi on your iPhone. You have taken some really good steps to troubleshoot this issue already. I found an article that includes a few additional steps you can try. You can skip any steps you have already taken.
I recommend reviewing the full article but the section titled "Unable to connect to a Wi-Fi network" specifically stands out to me for the issue you described:
Unable to connect to a Wi-Fi network
Verify that you're attempting to connect to your desired Wi-Fi network.
Make sure you're entering your Wi-Fi password correctly. Passwords may be case sensitive and may contain numbers or special characters.
Reset network settings by tapping Settings > General > Reset > Reset Network Settings. Note: This will reset all network settings including:
previously connected Wi-Fi networks and passwords
recently used Bluetooth accessories
VPN and APN settings
Find the full article here:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
Thank you for using Apple Support Communities.
Best,
Sheila M.

Voucher based guest access for vWLC (time restricted pre created user auth codes)

Hi all,
Is it possible to create voucher based user auth tickets for guest wireless on the Cisco WLC?
We are running the vWLC latest version
Cheers, Simon

No you can not create voucher using vWLC But you can create guest access using vWLC.
For the Guest access deployment ,plesae refer to the document below.
http://www.cisco.com/c/en/us/td/docs/wireless/technology/guest_access/technical/reference/4-1/GAccess_41.html#wp1000477

Since upgrading to OS 10.8.5 login keychain corrupted keeps asking for password for OSX, mail and Safari. Solutions?

Ever since upgrading to OS 10.8.5 login keychain corrupted; keeps asking for pasword tor OSX, mail and Safari. Help!

Have you tried opening Keychain Access and running Keychain First Aid (under the Keychain Access menu) on the login keychain?

Wired guest access with 5508

Hi
I have setup wireless guest access for a customer with a single 5508 and web authentication no problem at all. He then wanted to test wired guest access. The 5508 is currently connected to a single 3560 switch. The wired clients get a DHCP address OK but cannot reslove DNS and thus don't get redirected to teh guest login portal. I have even tried turning of all L3 security to no avail. The setup is as follows
VLAN 101 access points and 5508 management interface
VLAN 102 wired guest access dynamic ingress (L2 config only no SVI on 3560)
VLAN 103 wireless guest dynamic egress nterface L3 network with SVI on switch
VLAN 104 wired guest dynamic egress interface L3 network with SVI on switch
There are two DHCP pools setup on the WLC one for the VLAN 103 and one for the VLAN 104 subnets.
The internet router is also connected to the 3560 on a sepearte VLAN with an SVI. the 3560 has a default route to teh internet router and teh DHCP pools give the DHCP clients a default gateway of the IP address of dynamic interface 103 or 104. The Internet routre can ping the WLC on both these addresses.
LAG is enabled on teh WLC and VLANs 101-104 are trunked to it from the 3560.
I even tried making the wired guest egress interface the same one as for wireless. The wired clientys now got an IP address on the wireless range but still couldnt pass any traffic. It's like the intrenal bridging on teh WLC between VALN 102 and 104 (or 103) is broken. Tried both the lates 6.x and 7.x software on the WLC. Any ideas ? All the problems I can find with this seem to relate to not gettingas far as a DHCP address but that works fine.
Thanks
Pat

Hi
Yes got it resolved. It turns out that the connection from the wired guest access port to the WLC must be L2. That is the switch that the wired guest acces sport is connected and WLC are connected to must be L2 only. We were using a single switch to do the testing and it was also doing the routing for the test LAN. Even though there was no L3 VLAN interface configured for the VLAN that the guest access port was on for some reason this breaks it. Absolu Didnt have chance to work out the exact limitations of this as we simply made the switch L2 only and configured an 802.1Q trunk to the Internet router and made subinterfaces on the router for the wired and wireless egress ports and it worked then. No config change was needed on the WLC at all.
The only thing I can think of is that it's something about the way the WLC joins the wired guest access ingress VLAn and egress VLAN. The WLC isn't a reall router it says so in the documentation. I think the packet coming from the wired access port is being bridged to the egress VLAn not routed and this is what screws it up (remeber with a router the source and destination MAC addresses would be changed with a bridge they aren't). Got to be something along those lines. If you have a bigger newtork with a guest anchor WLC handling this function you dont run into this as the traffic is coming over an EOIP tunnle from the remote WLC so the switch with the guest anchor WLC doesnt see the MAC address of the wired guest PC.

Wired guest access on WLC 4400 with SW 7.0.240.0

Hello,
after we upgrade our Wlan-controller 4400 from software 7.0.116.0 to 7.0.240.0
wired guest access don't work anymore.
All other things works fine, incl. WLAN guest access!
When we try wired guest access, we get the web-authentication page and can log in.
On the controller we can see that the Policy Manager State changes from WEBAUTH_REQD
to RUN.
But then there is no access to the internet.
We tried also SW 7.0.250.0, same problem!
Log Analysis on the WCS:
Time :03/12/2014 14:21:23 MEZ Severity :INFO Controller IP :10.101.200.11 Message :The WLAN to which client is connecting does not require 802 1x authentication.
Time :03/12/2014 14:21:23 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client does not have an IP address yet.
Time :03/12/2014 14:21:23 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client L3 authentication is required
Time :03/12/2014 14:21:23 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client Moved to DHCP Required State.
Time :03/12/2014 14:21:26 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Mobility role update request. from Unassociated to Local Peer = 0.0.0.0, Old Anchor = 0.0.0.0, New Anchor = 10.101.200.11
Time :03/12/2014 14:21:26 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Mobility role changed. State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
Time :03/12/2014 14:21:26 MEZ Severity :INFO Controller IP :10.101.200.11 Message :DHCP successful.
Time :03/12/2014 14:21:26 MEZ Severity :ERROR Controller IP :10.101.200.11 Message :Client got an IP address successfully and the WLAN requires Web Auth or Web Auth pass through.
Time :03/12/2014 14:21:26 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client IP address is assigned.
Time :03/12/2014 14:22:01 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Webauth user logged in to the network. manni
Time :03/12/2014 14:22:01 MEZ Severity :INFO Controller IP :10.101.200.11 Message :AAA response message sent.
Time :03/12/2014 14:22:01 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client has completed Web Auth successfully.
Time :03/12/2014 14:22:01 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client has completed Web Auth successfully.
Trying http://www.google.de .... doesnt work. No Log Entries. Next entries while logging out.
Time :03/12/2014 14:36:20 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Web auth is being triggered again.
Time :03/12/2014 14:36:20 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client L2 authentication has been completed successfully.
Time :03/12/2014 14:36:20 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client Moved to DHCP Required State.
Time :03/12/2014 14:36:20 MEZ Severity :INFO Controller IP :10.101.200.11 Message :WebAuth user Logged out from network.
Has someone a idea how to solve this problem?
Regards
Manfred

Hi
Yes got it resolved. It turns out that the connection from the wired guest access port to the WLC must be L2. That is the switch that the wired guest acces sport is connected and WLC are connected to must be L2 only. We were using a single switch to do the testing and it was also doing the routing for the test LAN. Even though there was no L3 VLAN interface configured for the VLAN that the guest access port was on for some reason this breaks it. Absolu Didnt have chance to work out the exact limitations of this as we simply made the switch L2 only and configured an 802.1Q trunk to the Internet router and made subinterfaces on the router for the wired and wireless egress ports and it worked then. No config change was needed on the WLC at all.
The only thing I can think of is that it's something about the way the WLC joins the wired guest access ingress VLAn and egress VLAN. The WLC isn't a reall router it says so in the documentation. I think the packet coming from the wired access port is being bridged to the egress VLAn not routed and this is what screws it up (remeber with a router the source and destination MAC addresses would be changed with a bridge they aren't). Got to be something along those lines. If you have a bigger newtork with a guest anchor WLC handling this function you dont run into this as the traffic is coming over an EOIP tunnle from the remote WLC so the switch with the guest anchor WLC doesnt see the MAC address of the wired guest PC.

Guest Access 5.0 WCS Software

I am a little confused on the last two features for Guest Access Features. Anybody can explain in depth what these mean.
1. LDAP Web Authentication Support for Guest Access
2. Support for Proprietary Guest Access Solutions
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps6521/product_bulletin_cisco_unified_wireless_network_software_release_5.0_ps6366_Products_Bulletin.html
Thank You,
Reginald Bailey

Hey Anteaus,
Welcome to the BlackBerry Support Community Forums.
Since the BlackBerry Desktop Manager is causing conflicts with the network connections, I would highly suggest that you perform a clean uninstall of Desktop Manager.
Here is the link to a knowledge base article that explains all the steps for a clean uninstall.
http://www.blackberry.com/btsc/KB02206
Once you perform all of the steps in that article, then proceed with re-installing BlackBerry Desktop Manager.
The link to download BlackBerry Desktop Manager is available at:
http://na.blackberry.com/eng/services/desktop/
-ViciousFerret
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Like! for those who have helped you.
Click Accept as Solution for posts that have solved your issue(s)!

E4200 guest access won't ask for pasword

Similar Messages

Maybe you are looking for