E4200 Router Media Prioritization Fails to Load

Hi,
My E4200 router works fine in the sense that I have access to the internet through it. However, if I try to configure Media Prioritization through the Smart WiFi Tools interface, I simply get an endless "Waiting" 8-dot animated icon showing on the screen forever, with no further response from that browser window. When this happens, I still have internet access through other tabs in the open browser.
I have: Windows 7 Pro, It happens in Internet Explorer, Firefox, and Chrome - all the latest Windows versions. Most of the time, the only way to get it stop is to clear the browser cache or, sometimes, reboot the router.
The router has the latest verson of the firmware, which is 2.1.41.162351. I have updated the firmware several times to this same version, including a factory reset. Nothing helped.
Any ideas? (Buy a new router, probably).
Thanks,
Peter Wilde

"2112 error" is typically due to a browser cache issue. Clear the browser cache for the IP Address of the router and for www.linksyssmartwifi.com
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Similar Messages

Wireless Media Server: "Failed To Load Component of Media Serve

When I try to install Wireless Software it always ends up in telling me "Failed to load component of Media Server" after I've restarted the system. Media Server is not running and no icon of Media Server is to be found in the system tray. ?

I am having the same problem. Did you ever get a solution?
I've tried:
uninstalling/reinstalling all the software
forcing exceptions in my firewall (Norton), showing they permit all traffic from the Media Server & Console
assigning a static IP address (my router shows the receiver as connected to the network)
But I still get the "Failed to load component of media server" message every time I log in to Windows or try to start the Media Server manually. When I try to do the receiver's Network Setup (either letting my router assign and address, or with assigning the static address), at first I get the flashing green lights, then just a solid red, with the message that my settings are incorrect. Are those two separate problems, or the same problem?
I am using a 2Wire HomePortal Gateway. The main computer I am attempting to set up through is connected by Ethernet to the gateway. I am using WEP 64-bit encryption with a single key. There are notes about "open" vs "Shared key" modes, but I don't know where to find that info in the HomePortal's settings. I have connected a laptop and a PDA wirelessly with no problems once the key is entered. I can see the receiver on the gateway's summary page of my home network.
Any help is appreciated!

EA6700 Media Prioritization Not Loading

I just discovered this problem today. My firmware version is 1.1.40.160989. I used to be able to use this feature just fine.
Everything else is working for my router, but the Media Prioritization is not loading at all. When I try to open it, I get the "Waiting" box with moving dots in a circle. It just gets stuck there, and I have to clear my cache in order to return to the regular screen.
So I tried to download the app on my phone to access it from there as well. And it just says "Unexpected Error" and recommends that I contact Linksys support. Please help me. Thanks.

Unfortunately if this continues you may have to reset to factory defaults and reconfigure.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Failed to load Media Management Library

Hi,
I have an AIX Server which has 5 instances already running Oracle 9i and 1 instance on Oracle 10G.
We created a new database on this server and trying to run RMAN Backup. I get error message as follows:
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03009: failure of allocate command on mcb1 channel at 02/26/2009 09:16:43
ORA-00604: error occurred at recursive SQL level 1
ORA-01422: exact fetch returns more than requested number of rows
ORA-19554: error allocating device, device type: SBT_TAPE, device name:
ORA-27211: Failed to load Media Management Library
Additional information: 2
I found that libobk.a file is not available under $ORACLE_HOME/lib. I created a link to this file. Still i get same error.
Can any one advice what might be wrong? We are on Oracle 10.2.0.4.
Thanks,
Giridhar

Excellent. Thank you very much Anand. It worked with the recommendations made in that article.
Thank You.
Giridhar

AP Downloader-"Failed to load plugins to get media from devices"

I'm using Photoshop Elements 6.0/ Premiere 4.0, the problem comes up if I try to load to either program. I have it set to automatically download my pics when I insert a media card into my computer; the following dialog box comes up when I insert a card; Adobe Photo downloader- “Failed to load plugins to get media from devices”. I tried to fix the problem by using the Adobe CD, but the program asks for “Disk 1”, the original disk is in & I have no other disks. What needs to be done to correct this problem?
Thank You
photodave77

Dave,
Please close Organizer and delete the folder Organizer inside your user folder @ path: C:\Documents and Settings\<username>\Application Data\Adobe\Photoshop Elements\6.0\Organizer.
This would delete your APD preferences. If relaunch doesnot fix the problem, remove your card and restart your system and try again. Let me know if this works.
~V

Failed to load media | iTunes is not installed

Hello forum,
i am experiencing some problems with Media Sync.
When i start the application i receive the msg: Failed to load media.
Within the options the preferred music library "iTunes version 7.7.1 or greater is required" is selected but greyed.
On the main screen i can switch to Windows Media Player Playlists (nothing in there - wich is correct). When i switch back to iTunes Playlists, it tells me: iTunes is not installed.
Within the options the preferred music library "Windows Media Player" is now selected and "iTunes version 7.7.1 or greater is required" is greyed.
Here is what i tried so far:
reinstalling iTunes
reinstalling Media Sync
deleting the %appdata%\Research In Motion\BlackBerry Media Sync-Folder
formating the media card
Here is my setup:
MS Windows XP Professional Version 2002 SP3
MS .NET 3.5 SP 1 (and prior versions with latest SPs)
iTunes 9.0.2.25 (iTunes Plus, so no DRM)
BB Desktop Manager 5.0.1.28
BB Media Sync 3.0.0.38
BB Pearl 8110 corporate
This is the log:
[30000] (12/12 10:5:57):{1} Current Date: 2009/12/12
[50001] (12/12 10:05:57):{1} (Debug Log Level: 3)
[50001] (12/12 10:05:57):{1} (Event Log Level: -1)
[38017] (12/12 10:05:57):{1} (3.0.0.38)
[38018] (12/12 10:05:57):{1} (0.0.0.0)
[50002] (12/12 10:05:58):{9} (BlackBerry Connect: Started)
[37001] (12/12 10:05:58):{6} Log Cleaning Started.
[38050] (12/12 10:05:59):{4} (LoadDataSource: Started loading PicturesDesktop)
[38050] (12/12 10:05:59):{3} (LoadDataSource: Started loading WMP)
[38050] (12/12 10:05:59):{4} (Loading datasource from Rim.Media.Source.Pictures.PictureDataSourceLoader)
[38050] (12/12 10:05:59):{6} (Loading datasource from Rim.Media.Source.WindowsMedia.WMPDataSourceLoader)
[38050] (12/12 10:05:59):{3} (LoadDataSource: Finished)
[19036] (12/12 10:05:59):{4} (Library Refresh Complete for MediaSource: PicturesDesktop)
[38050] (12/12 10:05:59):{4} (LoadDataSource: Finished)
[38036] (12/12 10:06:02):{9} (255D9EFA: Connected)
[50002] (12/12 10:06:02):{9} (BlackBerry Connect: Finished)
[38050] (12/12 10:06:03):{6} (LoadDataSource: Started loading PicturesDevice)
[38050] (12/12 10:06:03):{6} (Loading datasource from Rim.Media.Source.Pictures.PictureDataSourceLoader)
[38050] (12/12 10:06:03):{6} (LoadDataSource: Finished)
[38041] (12/12 10:06:08):{3} (Data communication succeeded: True)
[38040] (12/12 10:06:08):{3}
[19033] (12/12 10:06:19):{3} EXCEPTION: Rim.Media.Source.DataSourceUnavailableException -- MESSAGE: Eine Ausnahme vom Typ "Rim.Media.Source.DataSourceUnavailableException" wurde ausgelöst. -- STACK:    bei Rim.Media.Source.iTunes.ITunesXmlDataSourceChangeWatcher..ctor(IFilePath iTunesXmlFile){CRLF}   bei Rim.Media.Source.iTunes.ITunesDetector.InitializeLibraryWatcher(){CRLF}   bei Rim.Media.Source.DataSourceDetector.CreateDataSource()
[19033] (12/12 10:06:19):{3} INNER EXCEPTION: System.InvalidOperationException -- MESSAGE: Der Vorgang ist aufgrund des aktuellen Zustands des Objekts ungültig. -- STACK:    bei Rim.Application.Utilities.FileSystem.FolderPath.WatchChildren(){CRLF}   bei Rim.Application.Utilities.FileSystem.FolderPath.WatchChildren(Boolean includeSubfolders, String pattern){CRLF}   bei Rim.Application.Utilities.FileSystem.FullPath.WatchSelf(){CRLF}   bei Rim.Media.Source.iTunes.ITunesXmlDataSourceChangeWatcher..ctor(IFilePath iTunesXmlFile)
[19006] (12/12 10:06:19):{3} EXCEPTION: Rim.Media.Source.DataSourceUnavailableException -- MESSAGE: Eine Ausnahme vom Typ "Rim.Media.Source.DataSourceUnavailableException" wurde ausgelöst. -- STACK:    bei Rim.Media.Source.iTunes.ITunesXmlDataSourceChangeWatcher..ctor(IFilePath iTunesXmlFile){CRLF}   bei Rim.Media.Source.iTunes.ITunesDetector.InitializeLibraryWatcher(){CRLF}   bei Rim.Media.Source.DataSourceDetector.CreateDataSource(){CRLF}   bei Rim.Media.Sync.BBMusicSyncAPI.CreateDataSource(MediaSource mediaSource){CRLF}   bei Rim.Media.Sync.BBMusicSyncAPI.LoadDataSource(MediaSource mediaSource, ICancelable parentTask)
[19006] (12/12 10:06:19):{3} INNER EXCEPTION: System.InvalidOperationException -- MESSAGE: Der Vorgang ist aufgrund des aktuellen Zustands des Objekts ungültig. -- STACK:    bei Rim.Application.Utilities.FileSystem.FolderPath.WatchChildren(){CRLF}   bei Rim.Application.Utilities.FileSystem.FolderPath.WatchChildren(Boolean includeSubfolders, String pattern){CRLF}   bei Rim.Application.Utilities.FileSystem.FullPath.WatchSelf(){CRLF}   bei Rim.Media.Source.iTunes.ITunesXmlDataSourceChangeWatcher..ctor(IFilePath iTunesXmlFile)
Thanks for reading and for the good work you guys do here in the forum

Hi Entro:
This might be a problem with running on a localized operating system.   We’re still investigating the root cause.
However, I have a suggested workaround – if you can try it and let us know if it works, that would be great.
1.       Close MediaSync and iTunes
2.       Hold down the shift key and double click your iTunes icon. Keep holding, and a little dialog should come up that says ‘Choose Library’
3.       Hit ‘create library’
4.       Navigate to a folder like c:\myituneslibrary – you’ll have to create this folder. It’s important that you create this folder outside of the standard ‘My Documents’ or ‘My Music’ location
5.       Hit ok, iTunes will launch. Import a few of your songs into this new library.
6.       Launch MediaSync
Hopefully Media Sync will launch and iTunes will load properly.
Cheers
M
Need additional information on BlackBerry products?
visit: http://www.blackberry.net

ORA-27211: Failed to load Media Management Library after Update to HP DP 6

Hi,
after an Upgrade to Version 6.0 from the Backupsoftware HP Dataprotector i can't run RMAN Backup's anymore, because something is wrong with Linking of the MML.
BS: SLES 8 / Kernel 2.4.21-251-smp
Oracle: 9.2.0.5
I try this RMAN Statement:
RMAN> run
2> {
3> allocate channel 'c1' device type sbt_tape
4> PARMS='SBT_LIBRARY=/opt/omni/lib/libob2oracle8.so';
5> }
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03009: failure of allocate command on c1 channel at 10/22/2007 16:04:24
ORA-19554: error allocating device, device type: SBT_TAPE, device name:
ORA-27211: Failed to load Media Management Library
Additional information: 2
the tracefile (i try RMAN Test with and without PARM Parameter):
Dump file /u01/app/oracle/product/9.2.0/rdbms/log/khv_ora_11745.trc
Oracle9i Enterprise Edition Release 9.2.0.5.0 - Production
With the Partitioning option
JServer Release 9.2.0.5.0 - Production
ORACLE_HOME = /u01/app/oracle/product/9.2.0
System name: Linux
Node name: dbtheresien3
Release: 2.4.21-251-smp
Version: #1 SMP Thu Sep 23 17:22:54 UTC 2004
Machine: i686
Instance name: KHV
Redo thread mounted by this instance: 1
Oracle process number: 35
Unix process pid: 11745, image: oracle@dbtheresien3 (TNS V1-V3)
*** SESSION ID:(72.47988) 2007-10-22 15:53:24.684
Failed to load SBT library libobk.so
*** 2007-10-22 15:57:35.736
Failed to load SBT library /opt/omni/lib/libob2oracle8.so
*** 2007-10-22 15:58:16.009
Failed to load SBT library /opt/omni/lib/libob2oracle8.so
*** 2007-10-22 16:02:46.904
Failed to load SBT library libobk.so
*** 2007-10-22 16:04:24.761
Failed to load SBT library /opt/omni/lib/libob2oracle8.so
All Infos i found tells me:
- that i doesn't need to restart the Instance of the Database
- i must only remove the old link in $ORACLE_HOME/lin/libobk.so and take a link new link $ORACLE_HOME/lin/libobk.so to the new Backuplibrary in /opt/omni/lib/libob2oracle8.so
But this doesn't work!
Any usefull Hints?
I always try the RMAN Command's:
CONFIGURE DEVICE TYPE 'SBT_TAPE' CLEAR;
CONFIGURE CHANNEL DEVICE TYPE 'SBT_TAPE' clear;
Nothing help...
My last Idea ist to reboot the whole Database, but this is a little difficult 8-)

hi,
all Systems are 32 Bit (Database Oracle 9.2.0.5 and DP6.0).
What do you mean with "what is Version DP6" ?
HP Dataprotector 6.0 with Patch DPLNX_00013
thx
Thomas

Failed to load to macro media flash player

hi am using windows 7 ultra 64 bit and am trying to use a program called bass guitar tips it runs of of flash player but every time i try it just get a failed to load to Macromedia player i checked with them for the issue but they just assured me that it wasnt thier program and i have a problem with flash ive check the forums and updated my flash to the latest version and deleted my cache file for flash / Macromedia if that helps but still not working any help would be appreciated thanks

Are you having problems with other Flash content (YouTube, etc?)
Can you try installing both of these installers then try again?
Flash Player for ActiveX (Internet Explorer)
Flash Player Plug-in (All other browsers)

Error 2118 - E4200V2 Media Prioritization Tool

Excuse my English, but it is not my native language.
I have a problem with my Linksys when I try to configure you E4200V2 Media Prioritization Tool .
The error is:
"Unexpected Error
2118
There was an unexpected error. If the problem persists, visit our web site technical support.
Details
http://linksys.com/jnap/devicelist/GetDevices: {"sinceRevision": 48960} - Date: Tue, 26 Aug 2014 21:17:39 GMT
Cache-Control: no-cache, no-store, max-age = 0
Server: Apache / 2.2.19 (Unix) mod_ssl / OpenSSL 2.2.19 / mod_jk 1.0.0d / 1.2.28
Connection: keep-alive
Content-Length: 280
Content-Type: application / json; charset = UTF-8 ".
This happens to me since the firmware was updated to version 2.1.41.162351 previously had the basic firmware.
Thanks a lot
Solved!
Go to Solution.

Thank FurryNutz, the router works as it should.
Spoiler (Highlight to read)
The error was in the imported data from the previous firmware.
Reestablished and the router will load the configuration and the error returned.
Then again reestablished, reinstall the firmware and configure everything manually.

WRT1900AC cannot get into media prioritization

Hi Guys,
i have my new WRT1900AC router fully configured. in the last 2 days from some odd reason i simply cannot get to the media prioritization section. Whenever i do the router just freezes on the "loading" section....when i go via the mobile app i see "an unexpected error occurred in the application"...
The only way to fix it is by rebooting the router, but then same thing i cannot get to the media priority section of the router....
i was able to grab maybe the error at some point:
http://linksys.com/jnap/qos/GetQoSSettings : {} -- Status: 200 OK Content-Type: application/json; charset=utf-8 Connection: close Content-Length: 276 Date: Sun, 27 Jul 2014 15:59:38 GMT Server: lighttpd/1.4.34
it says status 200 OK but thats the error itself... doesnt make sense...
Things i have tried:
Manually re-flashing the latest firmware.
reset the router to default (the it start working) but as soon as i restore my own config it breaks again...
i assume if i reset the router to defaults and then start again to configure it section by section from scrath it most likely will work.
but my own config is a lot a lot a lot of work and i am trying to avoid that......
any way to read an advanced log of the API call made to the router when i try to get to that section? or a way to troubleshoot this without start from scratch?
thank you.

MaSe_1981 wrote:
thank you,
i was afraid of that...
starting over from scratch is ALOT of work for me.....
Not sure if this is what happened to you but I ended up with a corrupt file because I didn't click on the pop-up while creating it. It never finished creating it.

FireFox images not loading in local folders (firebug error-Failed to load given URL)

I am having difficulty when developing websites in local folders (Windows7 computer). The webpages I make are showing images in IE9 & Chrome but not FireFox (nor Safari nor Opera).
In FireFox I get Firebug "Failed to load given URL" prompt.
I am using html5 & external linked css stylesheet & the html/html5 & css code validates.
I have tried using rel path ie images/image.gif & absolute path references ie C:/RPD_Programming/RPD WEB/amwcsnew/index.html
and have tried using % to eliminate whitespace in references but I cannot get FireFox to display images!!
This has been a problem for me for around 2 weeks now & is very frustrating. Some website code/templates I have downloaded from the internet display the websites properly (ie load images fine) when I open them locally in FireFox. Why does my code not allow the images to load in FireFox (paths/permissions/other issue??). How can I fix this?
Here is example css & html5 not displaying images from local directory in FireFox (fine in IE9 & Chrome):
style.css
/* CSS Document */
/*Basic Reset*/
margin:0;
padding:0;
html{
/* HTML5 display-role reset for older browsers */
article, aside, details, figcaption, figure,
footer, header, hgroup, menu, nav, section {
display: block;
body{
width:1200px;
margin:0 auto;
header{
height:450px;
background:url("C:/RPD_Programming/RPD WEB/amwcsnew/images/header.gif");
background-repeat:no-repeat;
#mid{height:750px;
background:url('C:/RPD_Programming/RPD_WEB/amwcsnew/images/mid.gif')no-repeat;
footer{height:286px;
background:url('C:/RPD_Programming/RPD WEB/amwcsnew/images/footer.gif')no-repeat;
index.html
<!doctype html>



<html lang="en" class="no-js">
<head>

<meta charset="utf-8">
<title>amwcs-new</title>
<meta name="description" content="amwcs">
<meta name="author" content="rpd">


<link rel="shortcut icon" href="/favicon.ico">

<link rel="apple-touch-icon" href="/apple-touch-icon.png">



<link rel="stylesheet" href="css/style.css?v=2">


<script src="js/modernizr-1.6.min.js"></script>


</head>


<body>




<header>

<hgroup>
<h1>amwcs</h1>
<h2>tagline</h2>
</hgroup>

<nav>
<ul>
<li><a href="#">Home</a></li>
<li><a href="#">About</a></li>
<li><a href="#">Services</a></li>
<li><a href="#">Contact</a></li>
</ul>
</nav>
</header>

<div id="mid">

<section class="hs1">


<p>Some content...</p>

<h2>Demonstrating EM and STRONG</h2>

<p><strong>This text will have more importance (SEO-wise and contextually)</strong></p>

<p><b>This text has visual importance but has no contextual or SEO importance</b></p>

<p>This is a <em>very</em> colloquial expression.</p>


</section>

<section class="hs2">
<h1>This is another section</h1>
<p>This is some dummy content</p>
</section>
</div>



<footer >
<p>copyright © year</p>
</footer>


<script src="http://ajax.googleapis.com/ajax/libs/jquery/1.4.4/jquery.min.js"></script>
<script>!window.jQuery && document.write(unescape('%3Cscript src="js/jquery-1.4.4.min.js"%3E%3C/script%3E'))</script>


<script src="js/general.js"></script>


<script>
var _gaq = [['_setAccount', 'UA-XXXXX-X'], ['_trackPageview']];
(function(d, t) {
var g = d.createElement(t),
s = d.getElementsByTagName(t)[0];
g.async = true;
g.src = ('https:' == location.protocol ? 'https://ssl' : 'http://www') + '.google-analytics.com/ga.js';
s.parentNode.insertBefore(g, s);
})(document, 'script');
</script>
</body>
</html>
I am most grateful for help & look forward to replies & fixing this-thanks
NB
Is there a FireFox guide/manual in pdf format available anywhere? I have not found one yet & a FireFox reference might be useful!

You need to use file:// as the protocol instead of C:/. The latter may never work (C:\ might).
Where is the main HTML located ?
Easiest if to store the images in a sub folder of the location because you can't go back via ../ beyond that root location for security reasons.
See:
*http://kb.mozillazine.org/Links_to_local_pages_do_not_work

[Solved] Ncmpcpp Visualizer Failed To Load (Blank)

I've install ncmpcpp and mpd and I've followed each guide to enable visualization. Unfortunately I don't know what have cause it to failed to load.
Everytime I hit '9' to reveal it, it just showing blank terminal..for your information all of my songs just played fine.
I used config from one of our member via this thread. here is my .ncmpcpp/config:
##### connection settings #####
mpd_host = "localhost"
mpd_port = "6600"
mpd_music_dir = "/home/drfreddy/Music"
mpd_connection_timeout = "5"
mpd_crossfade_time = "1"
mpd_communication_mode = "notifications" (polling/notifications)
visualizer_fifo_path = "/tmp/mpd.fifo"
visualizer_output_name = "my_fifo"
visualizer_sync_interval = "1"
visualizer_type = "wave" (spectrum/wave)
system_encoding = "utf-8"
##### delays #####
playlist_disable_highlight_delay = "5"
message_delay_time = "4"
# Playlist
song_columns_list_format = "(7f)[cyan]{l} (25)[blue]{a} (40)[red]{t|f} (30)[magenta]{b}"
song_list_format = "{$3[%l]$9} {$5%a$9} - {$2%t$9} - {$6%f$9}"
now_playing_prefix = "$b$1» "
now_playing_suffix = "$/b"
playlist_display_mode = "columns" (classic/columns)
autocenter_mode = "yes"
centered_cursor = "yes"
cyclic_scrolling = "yes"
mouse_list_scroll_whole_page = "no"
# # Bars
song_status_format = "{%a - }{%t - }{%b}"
progressbar_look = "─╼ "
titles_visibility = "no"
header_visibility = "no"
statusbar_visibility = "yes"
# Browser
browser_playlist_prefix = "$2plist »$9 "
browser_display_mode = "classic" (classic/columns)
# Colors
discard_colors_if_item_is_selected = "yes"
header_window_color = "default"
volume_color = "cyan"
state_line_color = "white"
state_flags_color = "green"
main_window_color = "default"
color1 = "cyan"
color2 = "black"
main_window_highlight_color = "red"
progressbar_color = "cyan"
statusbar_color = "white"
active_column_color = "red"
visualizer_color = "cyan"
# Others
song_window_title_format = "MPD: {%a > }{%t}|{%f}"
search_engine_display_mode = "columns" (classic/columns)
follow_now_playing_lyrics = "yes"
display_screens_numbers_on_start = "no"
user_interface = "alternative" (classic/alternative)
And here is my .mpdconf:
# An example configuration file for MPD
# See the mpd.conf man page for a more detailed description of each parameter.
# Files and directories #######################################################
# This setting controls the top directory which MPD will search to discover the
# available audio files and add them to the daemon's online database. This
# setting defaults to the XDG directory, otherwise the music directory will be
# be disabled and audio files will only be accepted over ipc socket (using
# file:// protocol) or streaming files over an accepted protocol.
music_directory "/home/drfreddy/Music/"
# This setting sets the MPD internal playlist directory. The purpose of this
# directory is storage for playlists created by MPD. The server will use
# playlist files not created by the server but only if they are in the MPD
# format. This setting defaults to playlist saving being disabled.
playlist_directory "~/.mpd/playlists"
# This setting sets the location of the MPD database. This file is used to
# load the database at server start up and store the database while the
# server is not up. This setting defaults to disabled which will allow
# MPD to accept files over ipc socket (using file:// protocol) or streaming
# files over an accepted protocol.
db_file "~/.mpd/database"
# These settings are the locations for the daemon log files for the daemon.
# These logs are great for troubleshooting, depending on your log_level
# settings.
# The special value "syslog" makes MPD use the local syslog daemon. This
# setting defaults to logging to syslog, otherwise logging is disabled.
#log_file "~/.mpd/log"
# This setting sets the location of the file which stores the process ID
# for use of mpd --kill and some init scripts. This setting is disabled by
# default and the pid file will not be stored.
#pid_file "~/.mpd/pid"
# This setting sets the location of the file which contains information about
# most variables to get MPD back into the same general shape it was in before
# it was brought down. This setting is disabled by default and the server
# state will be reset on server start up.
#state_file "~/.mpd/state"
# The location of the sticker database. This is a database which
# manages dynamic information attached to songs.
#sticker_file "~/.mpd/sticker.sql"
# General music daemon options ################################################
# This setting specifies the user that MPD will run as. MPD should never run as
# root and you may use this setting to make MPD change its user ID after
# initialization. This setting is disabled by default and MPD is run as the
# current user.
user "drfreddy"
# This setting specifies the group that MPD will run as. If not specified
# primary group of user specified with "user" setting will be used (if set).
# This is useful if MPD needs to be a member of group such as "audio" to
# have permission to use sound card.
#group "nogroup"
# This setting sets the address for the daemon to listen on. Careful attention
# should be paid if this is assigned to anything other then the default, any.
# This setting can deny access to control of the daemon.
# For network
bind_to_address "any"
# And for Unix Socket
#bind_to_address "~/.mpd/socket"
# This setting is the TCP port that is desired for the daemon to get assigned
# to.
port "6600"
# This setting controls the type of information which is logged. Available
# setting arguments are "default", "secure" or "verbose". The "verbose" setting
# argument is recommended for troubleshooting, though can quickly stretch
# available resources on limited hardware storage.
log_level "default"
# If you have a problem with your MP3s ending abruptly it is recommended that
# you set this argument to "no" to attempt to fix the problem. If this solves
# the problem, it is highly recommended to fix the MP3 files with vbrfix
# (available from <http://www.willwap.co.uk/Programs/vbrfix.php>), at which
# point gapless MP3 playback can be enabled.
gapless_mp3_playback "yes"
# Setting "restore_paused" to "yes" puts MPD into pause mode instead
# of starting playback after startup.
#restore_paused "no"
# This setting enables MPD to create playlists in a format usable by other
# music players.
#save_absolute_paths_in_playlists "no"
# This setting defines a list of tag types that will be extracted during the
# audio file discovery process. The complete list of possible values can be
# found in the mpd.conf man page.
#metadata_to_use "artist,album,title,track,name,genre,date,composer,performer,disc"
# This setting enables automatic update of MPD's database when files in
# music_directory are changed.
auto_update "yes"
# Limit the depth of the directories being watched, 0 means only watch
# the music directory itself. There is no limit by default.
#auto_update_depth "3"
# Symbolic link behavior ######################################################
# If this setting is set to "yes", MPD will discover audio files by following
# symbolic links outside of the configured music_directory.
#follow_outside_symlinks "yes"
# If this setting is set to "yes", MPD will discover audio files by following
# symbolic links inside of the configured music_directory.
#follow_inside_symlinks "yes"
# Zeroconf / Avahi Service Discovery ##########################################
# If this setting is set to "yes", service information will be published with
# Zeroconf / Avahi.
#zeroconf_enabled "yes"
# The argument to this setting will be the Zeroconf / Avahi unique name for
# this MPD server on the network.
#zeroconf_name "Music Player"
# Permissions #################################################################
# If this setting is set, MPD will require password authorization. The password
# can setting can be specified multiple times for different password profiles.
#password "password@read,add,control,admin"
# This setting specifies the permissions a user has who has not yet logged in.
#default_permissions "read,add,control,admin"
# Input #######################################################################
input {
plugin "curl"
# proxy "proxy.isp.com:8080"
# proxy_user "user"
# proxy_password "password"
# Audio Output ################################################################
# MPD supports various audio output types, as well as playing through multiple
# audio outputs at the same time, through multiple audio_output settings
# blocks. Setting this block is optional, though the server will only attempt
# autodetection for one sound card.
# See <http://mpd.wikia.com/wiki/Configuration#Audio_Outputs> for examples of
# other audio outputs.
# An example of an ALSA output:
audio_output {
type "alsa"
name "Beats by Dr. Freddy"
device "hw:0,0" # optional
format "44100:16:2" # optional
mixer_type "software" # optional
mixer_device "default" # optional
mixer_control "PCM" # optional
mixer_index "0" # optional
# An example of an OSS output:
#audio_output {
# type "oss"
# name "My OSS Device"
## device "/dev/dsp" # optional
## format "44100:16:2" # optional
## mixer_type "hardware" # optional
## mixer_device "/dev/mixer" # optional
## mixer_control "PCM" # optional
# An example of a shout output (for streaming to Icecast):
#audio_output {
# type "shout"
# encoding "ogg" # optional
# name "My Shout Stream"
# host "localhost"
# port "8000"
# mount "/mpd.ogg"
# password "hackme"
# quality "5.0"
# bitrate "128"
# format "44100:16:1"
## protocol "icecast2" # optional
## user "source" # optional
## description "My Stream Description" # optional
## url "http://example.com" # optional
## genre "jazz" # optional
## public "no" # optional
## timeout "2" # optional
## mixer_type "software" # optional
# An example of a recorder output:
#audio_output {
# type "recorder"
# name "My recorder"
# encoder "vorbis" # optional, vorbis or lame
# path "/var/lib/mpd/recorder/mpd.ogg"
## quality "5.0" # do not define if bitrate is defined
# bitrate "128" # do not define if quality is defined
# format "44100:16:1"
# An example of a httpd output (built-in HTTP streaming server):
#audio_output {
# type "httpd"
# name "My HTTP Stream"
# encoder "vorbis" # optional, vorbis or lame
# port "8000"
# bind_to_address "0.0.0.0" # optional, IPv4 or IPv6
## quality "5.0" # do not define if bitrate is defined
# bitrate "128" # do not define if quality is defined
# format "44100:16:1"
# max_clients "0" # optional 0=no limit
# An example of a pulseaudio output (streaming to a remote pulseaudio server)
#audio_output {
# type "pulse"
# name "My Pulse Output"
## server "remote_server" # optional
## sink "remote_server_sink" # optional
## Example "pipe" output:
#audio_output {
# type "pipe"
# name "my pipe"
# command "aplay -f cd 2>/dev/null"
## Or if you're want to use AudioCompress
# command "AudioCompress -m | aplay -f cd 2>/dev/null"
## Or to send raw PCM stream through PCM:
# command "nc example.org 8765"
# format "44100:16:2"
## An example of a null output (for no audio output):
#audio_output {
# type "null"
# name "My Null Output"
# mixer_type "none" # optional
# This setting will change all decoded audio to be converted to the specified
# format before being passed to the audio outputs. By default, this setting is
# disabled.
#audio_output_format "44100:16:2"
# If MPD has been compiled with libsamplerate support, this setting specifies
# the sample rate converter to use. Possible values can be found in the
# mpd.conf man page or the libsamplerate documentation. By default, this is
# setting is disabled.
#samplerate_converter "Fastest Sinc Interpolator"
# Normalization automatic volume adjustments ##################################
# This setting specifies the type of ReplayGain to use. This setting can have
# the argument "off", "album" or "track". See <http://www.replaygain.org>
# for more details. This setting is off by default.
#replaygain "album"
# This setting sets the pre-amp used for files that have ReplayGain tags. By
# default this setting is disabled.
#replaygain_preamp "0"
# This setting enables on-the-fly normalization volume adjustment. This will
# result in the volume of all playing audio to be adjusted so the output has
# equal "loudness". This setting is disabled by default.
#volume_normalization "no"
# MPD Internal Buffering ######################################################
# This setting adjusts the size of internal decoded audio buffering. Changing
# this may have undesired effects. Don't change this if you don't know what you
# are doing.
#audio_buffer_size "2048"
# This setting controls the percentage of the buffer which is filled before
# beginning to play. Increasing this reduces the chance of audio file skipping,
# at the cost of increased time prior to audio playback.
#buffer_before_play "10%"
# Resource Limitations ########################################################
# These settings are various limitations to prevent MPD from using too many
# resources. Generally, these settings should be minimized to prevent security
# risks, depending on the operating resources.
#connection_timeout "60"
#max_connections "10"
#max_playlist_length "16384"
#max_command_list_size "2048"
#max_output_buffer_size "8192"
# Client TCP keep alive #######################################################
# For clients connected by TCP on supported platforms.
# Allows detection of dangling connections due to clients disappearing from
# the network without closing their connections.
# This is not usually necessary but can be useful in cases such as wifi connectected
# clients that go in and out of network range or turn off wifi without closing their
# connections. Combined with low max_connections this can soon cause clients to not
# be able to connect.
# Enable tcp keepalive on new client connections (default is "no")
#tcp_keep_alive "no"
# Time in seconds since the last communication on the connection and before
# the keepalive probing is started. (default is 7200 seconds)
#tcp_keep_alive_idle "7200"
# Interval in seconds between keepalive probes, once a probe started.
# (default is 75 seconds)
#tcp_keep_alive_interval "75"
# Number of failed probes before the connection is pronounced dead and
# the connection is closed. (default is 9 times)
#tcp_keep_alive_count "9"
# Character Encoding ##########################################################
# If file or directory names do not display correctly for your locale then you
# may need to modify this setting.
#filesystem_charset "UTF-8"
# This setting controls the encoding that ID3v1 tags should be converted from.
#id3v1_encoding "ISO-8859-1"
# SIDPlay decoder #############################################################
# songlength_database:
# Location of your songlengths file, as distributed with the HVSC.
# The sidplay plugin checks this for matching MD5 fingerprints.
# See http://www.c64.org/HVSC/DOCUMENTS/Songlengths.faq
# default_songlength:
# This is the default playing time in seconds for songs not in the
# songlength database, or in case you're not using a database.
# A value of 0 means play indefinitely.
# filter:
# Turns the SID filter emulation on or off.
#decoder {
# plugin "sidplay"
# songlength_database "/media/C64Music/DOCUMENTS/Songlengths.txt"
# default_songlength "120"
# filter "true"
audio_output {
type "fifo"
name "my_fifo"
path "/tmp/mpd.fifo"
Can somebody tell me how to enable the visualization? Am I missing something?
Last edited by Archer1X (2013-02-07 10:48:34)

Nevermind..got it working after configured that I have to put this line in .ncmpcpp/config:
visualizer_look = "+|"
Anybody have a better look for the visualizer?
I also have tried several figures like "=="..hmm..kinda like it..
Last edited by Archer1X (2013-02-07 10:49:13)

Internet appears connected but pages fail to load after 3-5 minutes! HELP!

I purchased my Macbook three weeks ago and it immediately found my network and connected. A few days later my computer failed to load internet pages (both in firefox and safari). The connection would not disconnect, or seem to slow. I diagnosed and found no problems. To get it to work for small amounts of time I turn off airport and then turn it back on and get a few minutes before I get "Problem Loading Page".
I have updated the firmware in my router. I use a D-Link Router WBR-1310 and a D-Link Cable Modem DCM-202. I have called my cable provider, Comcast, and they tested the connection saying it was strong. I connected directly to the modem and it never failed to stop loading pages the full 20 minutes I was connected.
My computer has no problem connecting to other connections: The Library, neighbors, my parents' home. There are no time outs and it automatically connects through Airport, no problem.
I have called D-Link about the router. They're a bit confusing in troubleshooting the problem. They told me to connect my Ethernet cable to the computer and manually put in IP address, subnet mask, router address, and name server address. First, I don't know where to find any of that except for the IP address. Secondly, do they expect me to connect and leave the ethernet cable in my computer?
Have there been any problems with Macs and this router? What am I doing wrong and has D-Link given me good steps to take? My experience with them hasn't been so great so I'm skeptical. All of this is very upsetting, I can't enjoy my new Macbook at home.

FrankInColorado wrote:
Yes I had read about this. The point is, especially with something such as wireless, it has to inter-operate with everyone else out there. You would think Apple would do some testing before going to some "recommended" standard that obviously is not widely used in the real world. To someone who just bought a new MacBook, it doesn't matter that Apple is using the "new" recommended way. They just want to be able to connect everywhere they go.
No, networking is a world of standards and recommended procedures. This all used to be a lot easier when there were actual engineers who understood the RFCs running most networks.
You seem to think Apple just throws software over the wall. If that's true, you should swing by Cupertino some time and see if you can meet with a member of their software test groups; I'm sure they'd love to know that you think they don't do anything.
Or perhaps Apple is supposed to test their software with every ISP on the planet first.
And how many people posting in these forums have said when they turn Airport off and back on, then things work again for a while. If the issues are on the other side, why would that make any difference?
Did I or anyone else here say that changing to OpenDNS' servers would solve every issue with every person in each and every one of these threads?
But there have been many cases where switching to OpenDNS' servers does solve people's network delay issues. Hmmm, I guess Apple's cluelessness doesn't apply in those cases.
Come on. He connected directly to the modem and was loading Web pages for 20 minutes without any problem. He goes back to using Airport and the problem reappears. And you think it's reasonable to assume it was just a coincidence that the supposed DNS issue went away while he was connected to the modem and reappeared when he went back to Airport?
It depends now, doesn't it, as I just said.
Perhaps he tried "surfing to a few sites" while connected directly, and when that worked he went back to AirPort. Did he try going to the same sites? Different ones? We don't know.
In fact, even if he did visit the same sites, that wouldn't tell us anything either way as the DNS resolutions for those sites would have been cached when he was connected to the wired network.
This is the same thing that has happened to me since upgrading to Leopard. My wireless started going bad after some minutes of accessing Web sites. If I rebooted the machine, it would be fine again for a while. I finally just turned Airport off and plugged in an Ethernet cable. I have not had any trouble with accessing Web sites since - same ISP (Comcast), same DNS servers.
Tell me there is no Airport issue.
I never said there weren't issues. No one did. Except you implied I did.
Your approach to troubleshooting seems to be "Ah, Apple's software is broken, why bother."
1) There are many people whose problems have been solved by switching to OpenDNS' servers. That's fact.
2) There are many ISPs who have broken DNS servers. That's also fact.
3) Comcast has a variety of DNS servers spread across the country, so your results in Colorado may differ from those of a Comcast subscriber in a different state. Fact again.
4) You asked for reasons, I gave them, you don't like them. Obviously I must be an Apple shill. Funny, I'll have to ask why I haven't received a paycheck from Cupertino. Ever.
I understand your frustrations if AirPort isn't working for you, but don't turn around and drop into troubleshooting threads and tell people why suggestions we're making can't possibly address their issues just because they haven't solved your particular issue.
That would be just as silly as me assuming that because I haven't seen an AirPort drop since 2007, all of those posting in threads here are simply delusional or incompetent.
The only way to find out what's wrong in each case is to be methodical, and step one in diagnosing network delays is to see if DNS is at fault.
If it is, great, problem solved. If not, on to step two of a nearly infinite sequence.
One step at a time.

ITunes MATCH fails to load on iPhone4 after updating to IOS 6

iTunes MATCH is failing to fully load (display) on 1 of my 2 iPhone4 telephones after updating both to IOS 6. (My wife and I share the iTunes MATCH library using the same ID).
I have tried Signing Out and back In to iTunes, plus I have tried turning iTunes MATCH On & Off for this one iPhone 4 device, but the iTunes MATCH still fails to load.
The furtherest it ever gets is to display my previous Playlists and my Artists, Albums, etc that are in the cloud ...but the actual songs that are in the MATCH cloud never ever appear at all ...even after waiting hours!
The IOS 6 update seemed to work fine for both of our iPhone version 4 phones, but like I said above, only 1 of the phones is able to play music from iTunes MATCH now. This previous worked fine under IOS 5.1 for almost a year.
We also own an Apple TV 2nd generation and an iMAC with OS X 10.6.x, ...and those 2 device are also able play music that we have stored in the iTunes MATCH cloud with No Problem.
The issue seems to be with only this one phone.
Has anyone else experienced this? Does anyone have a suggested fix for this?

This helped me my repair my iPhone4's locally corrupted iTunes library (which calls my iTunes Match account) for all my music and music-video collection! It took all of 5 minutes to repair.
1. Google/download/install iExplorer (free program).
2. Plug in iPad or iPhone first, then open iExplorer.
3. Delete the iPad\Media\iTunes_Control folder's 3 Media SQL files.
4. Turn on iCloud/match in iPhone's (iPad's) iOS settings, which replaced the iPads music library with iCloud
A big THANK YOU to Michael Allbritton for pointing my in the direction of this solution!
Finally a note to Apple:
You will have to incorporate a way for users to view and self-repair the inner workings of their appliances if you wish to continue to sucessfully compete in this market ...remember what happened to Nokia for not forseeing the touch screen display many years ago! I would never expect my Mother, my young wife or even my teenage son to download something like "iExplorer" and use it to delete 3 corrupted database files; therefore, dear Apple, please incorporate the self-diagnosis and repair functionality offered by an iPhone Explorer type system into your iTunes software ...or something similar to that! Get with the program!

Error: The Task has failed to load on Execute Package Task using TFS Build and MSBuild.exe on dedicated Build Machine.

I'm trying to automate my building and deployment of SSIS packages using TFS build definitionss in conjunction with MSBuild.exe on a separate build machine.
I have successfully built and deployed my projects but receive the following error:
Error: Failed to load task "etl_UWP_Stage_tstg_7_Large",type "". The contact information for this task is "Microsoft Corporation: Microsoft SQL Server .... "
This error happens at runtime as well as if I perform a "Validate..." on the SSIS Catalog on the server.
This only occurs when trying to execute a package that contains an Execute Package Task. Any other packages that are doing the actual work are working just fine.
In addition, when I do the MSBuild from my developer machine with the same deployment process everything works fine, even the Execute Package Task.
I can even open up the project on the build machine in VS2012, rebuild all, then deploy and everything works fine.
Some things I've considered/verified:
1) Visual Studio 2012 and Visual Studio Data Tools 2012 are both on the build machine and my local machine.
2) The .NET version being used by VS2012 is the same on the build machine and my local machine.
3) I find it suspicious that the "Type" referenced in the error above is blank...but not sure where to go with that.
4) Obvious difference is that during the TFS Build and Deploy on the build machine, everything is running under the TFS Service account, rather than my account...once again...not sure where to go with this, but it is a significant difference.
Has anyone had similar issues or have any thoughts on things to try?
Thanks,
Jason

Not sure why I couldn't find this answer in my earlier searches...
But this thread solved it for me:
https://social.msdn.microsoft.com/Forums/sqlserver/en-US/3aa1e324-da32-4ea0-865c-c69f610ef262/failed-to-load-execute-package-task-error?forum=sqlintegrationservices
Essentially I had to install SSIS on the build machine so that the 64-bit version for
ExecPackageTask.dll, was available. I did this from the original media CD selection Integration Services as a feature.
Hope this helps someone in the future.

E4200 Router Media Prioritization Fails to Load

Similar Messages

Maybe you are looking for