E51 latest firmware update broke any WIFI attempt ...

I'm really pi__ed off now, after the latest firmwareupdate i get: "Web: No Gateway Reply" whenever I try to connect to ANY wifi connection, regardless off wep/public etc. What is really annoying is that this is NOT a new issue...it has been reported in earlier firmwares in all kinds of forums... and the lack of support from Nokia in this matter is mind boggling.
I want my phone fixed! and dont give any **bleep** like: "did you try to connect to another wlan etc." off course I have. There is no reason why my wlan spots wouldnt work after the update.
Does anyone have a solution to this annoying problem?

What you said made no sense, please explain what you meant if you even can. To be honest you sound like you have no idea what you are talking about. "But those are type of private WLANs and you can not browse them." Please define a private Wlan and why I should not be able to "browse" it.
There seems to be a bug within the DHCP client. Maybe it's not holding the RFC standards for DHCP because when I configure static IP on the phone, everything works properly. Please fix DHCP!
Funny enough I can access my router's configuration page from the phone but it just wont go through the internet.
Message Edited by deathray on 28-Apr-2009 08:45 PM

Similar Messages

  • HT3728 Does factory reset go back to latest firmware update.

    I have resently updated my airport express to latest firmware. The airport express is configured as an extension to my wifi with an Extreme as main device.
    Shortly after the firmware update (1-2 days) the express stopped working and status light turned yellow.
    I have since then tried to do factory reset several times without getting the device up and running again.
    When doing factory reset the status light turns yellow after releasing the button and stays amber with short interval with green (1 second every minute or so)
    I have not been able to discover the express from my iPad, iPone or iMac again.
    Could the reaons be latest firmware update?
    Any advice to get it back to normal?
    Thanks,
    Per

    Does factory reset go back to the latest firmware update.
    A Factory Default Reset will not affect the installed firmware.
    Shortly after the firmware update (1-2 days) the express stopped working and status light turned yellow.
    A solid amber light is unfortunately an indication that the internal power supply inside the AirPort Express is failing, or has failed.
    I have since then tried to do factory reset several times without getting the device up and running again.
    The AirPort Express has failed, and will need to be replaced.
    When doing factory reset the status light turns yellow after releasing the button and stays amber with short interval with green (1 second every minute or so)
    This is yet another confirmation that the Express has failed, and will need to be replaced.

  • Attempted Iphone 4 update to latest firmware update "failed"

    Ive attempted to update the Iphone to the latest firmware update  and it has failed 3 times, the final time it looked as though
    it worked but stopped and went into new mode to go-back to Restore to old  setting. Now it is locked up and asking me for the  admin backup password
    and everything I've tried is not working..  Not sure what to do at this point.
    The laptop I'm using is a Panasonic CF29 and running Windows XP with SP3 installed.
    I'm  open to any ideas at this point.
                Thanks Artman

    Then it's pretty hopeless. Normally the error message remains displayed until you click "OK", so it's surprising that you didn't see it. You can try the shotgun approach; just try a bunch of stuff in the hopes that it will work. But first I suggest trying to update it again, and this time watch it. The following list covers the most common causes of update failures:
    Open a Command window and type the command "netsh   winsock   reset"
    Reboot your computer
    Disable your antivirus and firewall
    Launch iTunes
    Connect the phone using a USB port directly on the computer, not a hub
    When the phone is recognized in iTunes click on it, then click Restore
    If the phone is NOT recognized in iTunes, disconnect it, the hold the HOME and SLEEP buttons for exactly 10 seconds until the screen goes black, then release SLEEP but continue holding HOME while you connect the cable and continue holding HOME until iTunes recognizes a phone in recovery mode
    If the update completes you are in business
    You mentioned being prompted for a backup password. If your backup is encrypted you will need to know the password to complete the restore; if you don't know it you will have to restore as New and manually add your content back. If it is encrypted you really did enter a password for it once, whether you remember doing so or not.

  • Internet stopped working on MBA after latest firmware update. Help please!!!

    Internet stopped working after installing the latest firmware update. WiFi still connects to router, our other mac desktop still connects to internet as usual (same network). I can't even re-install the MBA OS since it needs an internet connection!!!
    Any ideas?

    FIXED.
    I swapped our wireless router for a newer one, internet seems to work fine again (we were sent a new one by our internet provider which we never set up until now).

  • Mid 2006 iMac Boot Problem (Since latest firmware update)

    I have a Mid 2006 17" iMac. Ever since the latest firmware update in early December, about every other startup I've been having boot problems. After the white screen with the Apple Logo and the spinning wheel it goes to a blue screen like normal, but instead of the 'Loading Mac OS X' white window popping up it stays blue and the spinning loading wheel starts. I've left it loading for quite a while before and nothing changes. I have to do a force shut off by holding the power button. and then I start it up and it will boot normally.
    Any help would be appreciated.
    Thanks!

    Actually, I think it'san early 2006.

  • Can't send mail after latest firmware update

    My outgoing mail won't go out after the latest firmware update. I have 4 different accounts and none are working. Tried in various locations. Any ideas would be appreciated. Thanks

    Was this for 10.5.8???
    Others have reported it for 10.6.8 & up...
    http://x704.net/bbs/viewtopic.php?f=12&t=6118

  • Zen Touch latest Firmware Update...player not connec

    I tried installing the latest Firmware update for my Zen Touch (released 2-09).
    The player is connected and recognized by Windows and the Media Explorer. However, when I try to install the new Firmware it keeps saying "player not connected".
    I tried d/l two different language packages cause I wasn't sure what counted - player language or operating system langauge. Anyway, that didn't make a difference.
    So what do I do? I have no idea where to start. It's firmware for the correct device connected through Windows XP.
    I have made a firmware update before, which worked fine. After that I updated the media explorer software.
    Help is very much appreciated! Thank you in advance.
    -tina-Message Edited by tinas on 2-0-2005 08:56 PMMessage Edited by tinas on 2-0-2005 09:00 PM

    Perhaps it's worth making sure no software is using the player, so reboot the PC, and turn off the Creative Detector. Then try again.
    Are you trying to upgrade to the .0.03 version?

  • Can't activate iPad. Restoration stops during firmware update. Any ideas?

    Can't activate iPad. Restoration stops during firmware update. Any ideas?

    Oh yeah i checked the firewall issue, and itunes is enabled.

  • HT1296 I'm having difficulty syncing my iCal between my home computer and iPhone.  New entries from my home are not syncing with the phone and vice-versa.  I didn't have any problems with this before until the latest phone update.  Any suggestions?

    I'm having difficulty syncing my iCal between my home computer and iPhone.  New entries from my home are not syncing with the phone and vice-versa.  I didn't have any problems with this before until the latest phone update.  Any suggestions?

    It could be that the existing wire in your appartment is not clean enough to provision DSL only. When combined with the phone possibly it has a higher line voltage and worked before. Now that the line is to be provisioned without phone service it may be giving them trouble that did not show before they came out and ran the new line test. So a new jack dedecated for your DSL line may require a new wire be run to your appartment. Also the account for internet only used to require direct billing to a credit card or something else. This was a number of years ago. Most accounts are linked to a phone number, and without a voice number it adds to the confusion.
    If you are getting the voice and everything turned on as before, then I am at a loss for words.

  • Latest iTunes update broke my iPod 3rd gen connection

    Recently, iTunes decided to send an update to break my iPod connection. Well, it worked. It broke any connection to iTunes, as well as my system.
    I have;
    - tried resetting the iPod. (http://support.apple.com/kb/ht1363)
    - UnInstalled -ALL- Apple software
    - Re-Installed iTunes
    Result - iPod shows connected on the iPod, but not in Windows.
    What else can I try??
    ORA

    Newest attempt;
    Unistall everything Apple.
    Install iTunes 8.2.1
    iTunes still fails.
    The Apple Mobile Device USB Driver shows an error and failure to connect even though it is the latest driver.
    6.0.9999.43
    ORA

  • WAP4410N wireless traffic locks up even when running latest firmware update

    I maintain multiple buildings, and each building has anywhere between 1 and 4 Cisco/Linksys WAP4410N access points. The problem is that at random intervals, the access points just stop sending and receiving wireless traffic. Every day or two, I have to log into every single access point (either via HTTPS or SSH) and reboot them in order for them to start working again.
    In short, here are the config details:
    They are all version 2 hardware (either WAP4410N-A V02 or WAP4410N-E V02).
    They are running IPv4 (IPv6 is disabled) and get static IP addresses via DHCP.
    When there are WAPs with overlapping signals, each WAP is on a different non-overlapping channel (1, 6, or 11).
    Each WAP has two SSIDs (with spaces in their names). One is secured with WPA2. The other is unsecured.
    There are two VLANs on the Ethernet interface. Each of the two SSIDs are assigned to a separate VLAN.
    There is a DHCP server on the network, so the WAPs do not actually assign IP addresses to clients.
    All of the WAPs are running on PoE switches. However, some are gigabit and some are 10/100 switches. Brands vary (Dell and Linksys) and models vary.
    Cisco finally recognized this issue as:
    CSCtx62203—In certain environments and traffic model, the WAP4410N may lockup after some undetermined time. Workaround: Reboot the device.
    As such, the workaround didn’t really offer anything new. Rebooting every WAP ends up being a very time consuming process. It’s awful. And since you have no control over when this issue surfaces and can’t put any safeguards in place, I get calls about it at various points of the day almost every day.
    Supposedly the most recent firmware update (2.0.6.1) claimed to fix the issue, but it only seemed to make it worse. So now instead of a WAP locking up every day or two, it locks up anywhere between every 15 minutes to 4 hours when in use.
    The firmware was updated and the following issue was fixed in firmware version  2.0.6.1: CSCtx62203—In certain environments and traffic model, the WAP4410N may lockup after some undetermined time. (A protection mechanism was added to guard against sporadic problems with client association that could occur after six to 24 hours.)
    As for troubleshooting, there are no error packets. On access points running firmware 2.0.6.1, these messages appear:
    Feb  7 13:42:27 Syslogd start up
    Feb  7 13:51:59 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 13:52:01 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 13:52:05 syslog:  Found beacon stuck, down and up the VAP interface.
    Feb  7 14:47:01 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 14:47:02 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 14:47:05 syslog:  Found beacon stuck, down and up the VAP interface.
    Feb  7 15:22:53 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 15:22:56 syslog:  Found beacon stuck, down and up the VAP interface.
    Feb  7 16:15:19 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 16:15:33 syslog:  Found beacon stuck, down and up the VAP interface.
    Feb  7 12:27:25 Syslogd start up
    Feb  7 14:06:18 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 14:06:23 syslog:  Found beacon stuck, down and up the VAP interface.
    Feb  7 14:44:28 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 14:44:31 syslog:  Found beacon stuck, down and up the VAP interface.
    Feb  7 15:09:18 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 15:09:24 syslog:  Found beacon stuck, down and up the VAP interface.
    Feb  7 15:42:23 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 15:42:25 syslog:  Found beacon stuck, down and up the VAP interface.
    Feb  7 16:52:18 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 16:52:24 syslog:  Found beacon stuck, down and up the VAP interface.
    Feb  7 16:53:05 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 17:20:05 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 17:20:08 syslog:  Found beacon stuck, down and up the VAP interface.
    Feb  7 17:23:34 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 17:23:39 syslog:  Found beacon stuck, down and up the VAP interface.
    Feb  7 21:21:28 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  7 21:21:30 syslog:  Found beacon stuck, down and up the VAP interface.
    Feb  8 09:55:23 kernel:  ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
    Feb  8 09:55:29 syslog:  Found beacon stuck, down and up the VAP interface.
    These log messages appear on both WAP4410N-A V02 and WAP4410N-E V02 devices.
    I noticed that when the “beacon stuck” message appears, wireless traffic locked up 10-15 minutes prior to the message’s appearance in the log, and the SSID drops for 4-6 minutes after the message appears.
    Is there anything that can be done to address the issue?

    1) LAN port speed doesn't appear to have any effect
    2) Forcing a connection type doesn't seem to have any effect. This is also rather impractical.
    3) I don't have that option (though there is a TKIP/AES mixed option). Either way, I'd rather not have to resort to using a weaker encryption method.
    4) No effect.
    I did manage to find some information about the error message (older versions of firmware didn't even offer that clue).
    http://www.dd-wrt.com/wiki/index.php/Advanced_wireless_settings#Beacon_Interval
    I ended up increasing the beacon interval from 100ms to 500ms under Wireless > Advanced Settings.
    The wifi analyzer app on android seems to keep dropping the SSID when the beacon interval is set that high, so I might have to adjust it to find a good balance.
    However, while it was set to 500ms, none of the access points went down for two days.
    [edit]: I reduced the beacon interval incrementally down to 300ms. It started locking up at 250ms.

  • TC issues after latest firmware update

    Here is the skinny, my TC went through the normal firmware update a bit ago. Wednesday my Internet stopped working, when I use the Airport Utility app it showed the TC online, at first, then it gave me the error that the TC did not have a valid IP. Thought might have been a problem on my ISP's end so I grabbed another router and set it up Internet no problem. Has to be the new firmware right so I pushed the firmware back 3 versions, and still the same thing no valid IP but connected to the Internet but no HDD (Yes it said not a valid IP but connected to the Internet on one wireless PC). Everything else in the house would not connect to the TC they could see it but when you went to connect never asked for a password and I got the spindle of death type deal. I saved my settings and did a hard reset with the button on the back of the TC, started over and rebuilt the connection, same thing happened not a valid IP. I have read that Apple released 3 different firmware updates supposedly the last one works, it doesn't when I load the firmware I get the same error TC does not have a valid IP. I need some help, I have cycled through power down and power up situations over and over. Anyone have any other suggestions?

    Need some more info.
    What is the modem.. make and model?
    Is it both modem and router or just a modem?
    What is the actual model of the TC.. the number from the base.. A1xxx where the x are numbers.
    The latest firmware is an issue.. that is 7.6.4 and you should go back to 7.6.1
    But it does seem hard to get rid of properly.
    I want you to do a factory reset not just a hard reset.
    Universal Factory Reset.. any model TC or AE.
    Unplug your TC/AE from power or turn off at the power point.
    Hold in reset. and power the TC/AE back on..  all without releasing reset and keep holding in for about 10sec. (this is often difficult without a 2nd person or a 3rd arm).
    Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
    Note..
    Be Gentle! Feel the switch click on. It has a positive feel..  add no more pressure after that.
    TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations of the router.
    No files are deleted on the hard disk in a TC.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
    Please redo the setup using all SMB names.. that is short, no spaces and purely alphanumeric characters.
    eg TCgenx (use actual gen if you want) for base station name.
    TCwifi for wireless name. (or TC24ghz and TC5ghz which is well worth naming both bands so you can test more carefully).
    Please download and install a v5 utility on a computer if any of them use up to Mountain Lion.
    Tell us what OS the computers are running and I can tell you how to install the old airport utility.
    Test the TC in bridge to your other router is also a good alternative.

  • Latest firmware update killed my network, HELP!

    so.. I updated the firmware about a month ago when it was first available.. My device is completely stock and i'm not really ready to root nor factory reset it. I reset it before due to an error on the backup assistant screwing with my external sd card (the real issue was the copy and paste error some devices were faced with). I've been through about 4, 32gb externals and the latest sandisk just sent me.. is bad too. :/
    But, that's not the issue i'm getting at. Since the lastest firmware update with caller ID, etc.. I've had little to no signal, dropped messages in my house, completely dropped 4G LTE while using GPS.. horrible due to some areas I was in.. slow or lagged device to the point where i've had to restart my device 3-4 times each day in the last week...
    Can someone either tell me if there is a quick solution to this or what the next step should be in this process. because this whole "we've retracted the update but are looking into a fix" ** isn't very settling. Since, on Verizon's time.. I'm afraid the next update won't come for a few months..

    I am having the same issues described by everyone else (dropped 4G, worse signal, etc.) after the update to MD3.
    My wife's phone is identical but without the update and it works fine (like mine did before the update)
    WHAT is the resolution to this issue, Verizon? I really don't believe I should have to go down the root-my-phone route and find third party sources to fix this issue. Why can't you just push the old firmware back to my phone?
    I am quite disappointed that what was my best smartphone experience to date has been ruined.

  • Latest firmware update and more problems with 30" external displays?

    Hello,
    New macbook pro user since a few weeks, so first post here.
    I'm aware of various issues with the displayport to dual-dvi adapter, especially with 30" 2560x1600 monitors. All threads I've found on are 1-3 years old though.
    I got my 17" macbook pro a few weeks ago and I've had very few problems running my 30" dell 3008wfp as external screen. I had issues at times getting it to work after boot up, with blackout and various errors (problems I've read about in older threads), but once stable it would work without issues for days.
    Yesterday the macbook found and installed a new firmware update, and wow, all **** broke lose. The external screen won't run at 2650x1600 for more than a minute before blacking out or suffering major graphical errors. Ironically one of the key points in the firmware update is better support for external monitors...
    It will run nice and stable mirrored at 1920x1200, but not at 2650x1600.
    Is anyone else in a similar situation after the latest update?

    Hello,
    New macbook pro user since a few weeks, so first post here.
    I'm aware of various issues with the displayport to dual-dvi adapter, especially with 30" 2560x1600 monitors. All threads I've found on are 1-3 years old though.
    I got my 17" macbook pro a few weeks ago and I've had very few problems running my 30" dell 3008wfp as external screen. I had issues at times getting it to work after boot up, with blackout and various errors (problems I've read about in older threads), but once stable it would work without issues for days.
    Yesterday the macbook found and installed a new firmware update, and wow, all **** broke lose. The external screen won't run at 2650x1600 for more than a minute before blacking out or suffering major graphical errors. Ironically one of the key points in the firmware update is better support for external monitors...
    It will run nice and stable mirrored at 1920x1200, but not at 2650x1600.
    Is anyone else in a similar situation after the latest update?

  • New symptoms since latest firmware update

    OK I have a 1tb sky hd box which hasn't had any really annoying issues up until the new firmware update (the one with the new Kids tile which is annoying in its own right).  Anyway, I have been watching the cricket on SS2 and every so often when they break for a short advert between overs I've lost sound when it tries to revert to DD5.1 after switching from 2.0 on the adverts.  I have to change channel and back again to get the sound back.    Also, for the first time, my planner was showing empty today so I had to do a planner rebuild which solved the issue.  Still, at least they  seem to have solved the sound dropout issue.  So just heads up for anyone else with a 1tb box who experiences the same issues.

    (Quoting Karl Petersen here:)
    There's a bug in iMovie 6 that makes it impossible to re-edit (Update) photo clips previously imported with the Ken Burns checkbox ON. The source photo, normally stored in the Media folder of the project, is (inappropriately) discarded when you empty the iMovie trash. The clips Update as black clips and the preview is usually black too, if I recall.
    The workaround is to 1) drag the photo from the iMovie trash to the iMovie Clips pane; or 2) never empty the iMovie trash.
    Sue

Maybe you are looking for