E531 - When standard headphones plugged into jack, built-in mic is disabled
Greetings everyone ! Lemme start by saying I genuinely feel guilty when my first ever forum post is about a problem/issue, but apparently it's my curse, lol. Per standard rules, I did search through the Edge listing for a solution to my issue, but no luck. So:
The E531 has one headphone jack, however it's apparently intended use is for headSETS ('phones/mic combo). Currently, my only interest for the port is standard headphones. However, there is an issue: when a pair of standard headphones are plugged in, the built-in mic is disabled so the mic on a headset can be used.
Is there a setting or config change anywhere in the E531 that would allow the built-in mic to be used when standard headphones are plugged in to the headset jack? I've played around with audio settings as far as I dare to. Please, any help would be greatly apreciated.
edit: I'm not sure how my Subject line got completely reworded, but I've changed it to suit my topic. Sorry for the confusion.
There is definitely something strange here. I tried to reproduce your issue and if I plug headphones or headset I can still switch the microphone and speakers under Control Panel>Sound.
Have you got the latest sound card drivers?
Vince.
Knowledge is of two kinds. We know a subject ourselves, or we know where we can find information on it.
ThinkPad T510 4313-CTO Windows 8 x64 - Intel Core i7-620M - NVIDIA NVS 3100M - 8GB RAM - 240GB SSD- Intel Centrino Ultimate-N 6300 - Gobi 2000.
ThinkPad Helix 3697-CTO Windows 8.1 x64 - Intel Core i7-3667U - Intel HD Graphics 4000 - 8GB RAM- 256GB SSD - Intel Centrino Advanced-N 6205 - Ericsson C5621gw
Similar Messages
-
When I have headphones plugged into my iphone it says warning'' high volume'' and becomes first a red and then plop a number of red pops but it will not be so for someone else I know. My sound will be much lower than anyone else in the music, and when I talk by phone headset
Hi! I have the same problem when I use my headphones .
iPhone 4s England, iOS 6.1.2 -
My iPad is not recognized by Finder or iTunes when it is plugged into the computer. i ran the Restore sequence and got an error message stating "The iPad could not be restored. An unknown error occurred (1611). Can this be fixed?
iTunes: Specific update-and-restore error messages and advanced troubleshooting - http://support.apple.com/kb/TS3694 - relating to iPad, iPhone, iPod touch, iTunes
Security software issues covered in: iTunes: Troubleshooting security software issues - http://support.apple.com/kb/TS3125 -
Itunes will not recognize my ipod nano when it is plugged into the computed
itunes will not recognize my ipod nano when it is plugged into the computed
Check this post: https://discussions.apple.com/message/6985613#6985613
-
I have always been able to create playlists on itunes, then drag them to my ipod when it is plugged into the mac. I recently downloaded the latest version of itunes, and now am unable to do that. I can drag songs and albums to the ipod, but not my playlists. It used to be so easy, am I missing something here?
Plug your iPod into your computer, it will begin to sync. Now check to see if the playlists have been added.
If not, go to the songs tab under your iPod when it is connected to iTunes, Unless you have checked "Sync all songs (or something to those words)" you should have an option on what you can put on your iPod. Make sure to check the playlists that you want on your iPod. -
I plug my computer into my stereo and use the remote app on my iPhone to control it. How can I control my wires iPad with the remote app on my iphone when it is plugged into the stereo? they are different iTunes accounts.
I think this is probably a sign that your network could be better than it is.
Intermittent problems are often a result of interference. Interference can be caused by other networks in the neighbourhood or from household electrical items.
You can download and install iStumbler (NetStumbler for windows users) to help you see which channels are used by neighbouring networks so that you can avoid them, but iStumbler will not see household items.
Refer to your router manual for instructions on changing your wifi channel or adjusting your multicast rate.
There are other types of problems that can affect networks, but this is by far the most common, hence worth mentioning first. -
My ipod nano 4th generation only works when it is plugged into the computer; otherwise, the screen turns black and it is completely unresponsive to any efforts such as pushing buttons, reseting, etc. What should I do?
Sounds like the battery is shot and in need of a replacement. You can have Apple replace the battery for a flat fee or you can send it into a third party repair center for a bit less.
Not much else you can do for troubleshooting this one.
B-rock -
My sister gave me her 1st gen iPad to see if I could solve an issue. It won't turn on, and when it's plugged into a power cord there is a slow pulsing sort of flash that happens on the screen....any ideas?
Try a Reset [Hold the Home and Sleep/Wake buttons down together for 10 seconds or so (until the Apple logo appears) and then release. When the screen goes blank power On again in the normal way.] It is absolutely/appsolutely safe! Now see if it charges normally and after a period try to turn it on again. If the batter has been drained it could take 20 minutes or so for it to show that it is charging.
Also considering if the battery need replacing! -
I'm new to Logic Pro X and can't work out how to record my voice over existing tracks without them playing over the speaker. I'm using a Sure mike through an audio interface and have headphones plugged into the interface?
Hi Kevin, what kind of audio interface do you have?
-
I have a macbook air and and hdmi that i have used many times, but not all of a sudden the tv won't recognize the hdmi. The computer flashes when it is plugged into the hdmi but the tv says "no signal" and the airplay displays option says "no device detected" and the drop down bar is grey and locked.
I have a macbook air and and hdmi that i have used many times, but not all of a sudden the tv won't recognize the hdmi. The computer flashes when it is plugged into the hdmi but the tv says "no signal" and the airplay displays option says "no device detected" and the drop down bar is grey and locked.
-
When my phone is not plugged into the charger or computer, it will not turn on at all; even though it is not dead. When it's plugged into the computer, it will go to a white screen with a grey apple icon and then it will turn off again and repeat. IOS7 and iPhone 5.
http://support.apple.com/kb/HT1808
Try this step and if you cannot get your device into recovery mode there is a chance you have a hardware failure and you need to call apple to see what service options you have. -
Im trying to update my iphone 5s to ios 7.1 but it just keeps sending me an error message even when i am plugged into itunes
The exact wording of Error messages and Alerts are imperative in ascertaining your issue.
Clearly state the Troubleshooting Steps you have tried to Resolve it -
HT4236 I can't see any photos when ipad is plugged into computer.
I can't see any photos in itunes when ipad is plugged into computer.
Everything else shows up.I have a similar problem Win 8 iCloud 3. Shared photostreams sync ok and my photostream syncs on other devices. Interesting enough, when I access photostream through the "my computer" option on Apple TV I see a whack of pictures that don't appear on any of my IOS or Windows Photostreams.
-
It says not charging when it is plugged into my mac desktop
My Ipad 2 says not charging when it is plugged into my computer and it does not show up on the side bar in the itunes app.
It is possible that the USB port is not working properly as well. This support article might be of help.
http://support.apple.com/kb/ts1591
Sometimes all it takes is a restart - quit iTunes, restart your Mac and restart your iPad and see if that helps at all.
Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button. -
When iphone 5s plugged into my macbook it charges but isnt recognized
when iphone 5s plugged into my macbook it charges but isnt recognized in itunes or iexplorer. Both my ipads connect no problem, not the iphone though?
If your computer is running Windows, go to Control Panel > Administrative Tools > Services. Check to see if "Apple Mobile Device" Service is Started. If not right click on this service and select Start. Also make sure Startup type is set to Automatic. If not, right click on this service, select Properties and set it to Automatic.
Maybe you are looking for
-
Bluetooth [BT] failed during use.Menu bar icon remains as does two BT icons in Utilities folder. System Prefs. BT icon totally gone. Remaining icons say "No BT Hardware Found" - " BT Not Available" etc. Have 3 yr. old MacBook Pro Notebook with OSX 10
-
File keeps downloading on my home page,rpc-1.html
when I log onto comcast, it keeps downloading a file. (file:///C:/users/tina/AppaData/LocalTemp?rpc-1.html. how do I stop it
-
I have just today started to use Goggles Mapping. Is there anyone who can get me started with this App? I am using a I-pad. Thank you,
-
JCo getting truncated value from SAP when field data type is RAW
We are trying to fetch data from a SAP-AII table by using JCo using the RFC RFC_READ_TABLE. We are getting incomplete data when the data type of the column is RAW in a particular table.A typical case is: Table Name: /AIN/DM_DEVCTR Field : CLIENT
-
Hi Team, In the forums, it is said that personalization is used to store the variable values like bookmarks. then what is the difference between variant and personalization. Regards, Dinesh.