E61i WPA Wlan not working

Hi,
I have D-Link WLan router.
From my E61i I am unable to connect.
currently the WLAN router supports WPA mode.
My E61i trying for long to connect.....
if there is no password protection then its working fine.
what could be the reason.
Should I change it to WEP mode?
sudipta

I think u should add the WLAN MAC address to the router.
I had the same problem with me in my company and the tech specialist told me to add the mac address to the router in order ot use the wi-fi

Similar Messages

WLAN not working after v30 update on N95

I saw a previous thread about WLAN not working on the N96 after update.
I can now confirm that WLAN is also bugged for the N95-1 after firmware update to v30.
It tries connecting, then after a few seconds, I always get the message "WLAN: Unable to connect. WLAN network not found"
This did not happen a few minutes before the update. Last firmware version was the v22 (latest one before v30)
Has any fix been found? My main usage for my phone is for the wifi, and without it I can't do much

Nokia is the host of this forum, however the forum operates and functions with the participation of common folk, users from all over the world that either share passion for Nokia or are looking for support and answers from other community members...if you want to complain to Nokia there is a : Contact us - button on top right of this page...if you want to try to find answers patience sometimes is a virtue....now the issue of untrusted software, there are applications and sometimes themes that you have installed on your memory card/mass memory that will give that message when you go to application manager it will list the apps that are installed and that are not installed on your device, you can either install them manually or remove them from your phone, the next time you restart your phone you should have no problems with those messages. now the WLAN issue i am not sure about and I am almost certain it has nothing to do with your untrasted software messages.
You know what I love about you the most, the fact that you are not me ! In love with technology and all that it can offer. Join me in discovery....

Satellite L350D - WLAN not working after recovery disk

Hello there
I just got a L350D. I ran the Recovery Disk tool, without any other programm running. It was on a good way of finishing the second disk and than: BAM! blue screen. Since the start up, my LAN and WLAN is not working.
It always says "WLAN 2.0 bg Adapter" to which no driver is found. The correct driver is a Realtek for both WLAN and LAN.
Do you think the crash busted the WLAN and LAN module?
Things i tried:
System reset
Driver reinstall
but nothing worked.
Has anyone any hints?
Thanks a lot!
mycale

Hi!
I dont know what the reason is for this BSOD during the installation but can you post the BSOD code? So you can search on the Microsoft Knowledge Base for this code.
Furthermore I would try to update the BIOS of your notebook that you can find on the Toshiba website:
http://eu.computers.toshiba-europe.com => Support & Downloads => Download Drivers
After you have updated the BIOS try to update the driver of WLAN and LAN card or try to reinstall Windows again using the Toshiba recovery disk.
Bye

Wep key and wpa does not work.

I'm trying to set up security for my router using wep or wpa but everytime I set it up, my key does not work. The router is suddenly disabled. I did exactly as the how to setup wireless security said. do u have to hard reset to get it to work. I've been trying to set security for three days. Your help is appreciated.

First of all, give your network a unique SSID. Do not use "linksys". If you are using "linksys" you may be trying to connect to your neighbor's router. Also set "SSID Broadcast" to "enabled". This will help your computer find and lock on to your router's signal.
For WEP, you must enter WEP "key 1" (found in the router) into your computer, not the WEP password or passphrase.
For WPA or WPA2, enter the key (sometimes called password or passphrase) into your computer.
Note that for WPA or WPA2, use "personal", not "enterprise".
Also, nomenclature sometimes causes problems. Note the following:
WPA = WPA with TKIP = PSK
WPA2 = WPA with AES = PSK2
Also note that Windows XP requires SP3 to run WPA2 ( = WPA with AES).
Also, each time you try a new encryption method, you must remove old settings from your computer. To do this, do the following:
In the computer, go to your wireless software, and go to "Preferred Networks" (sometimes called "Profiles" ). There are probably a few networks listed. Delete any network named "linksys". Also delete any network that you do not recognize, or that you no longer use. Delete your current network (this will remove any old settings). Reboot computer. Return to "Preferred Networks" and re-enter your current network info (SSID, encryption (if any), and key (if any) ). Then select your current network and make it your default network, and set it to automatic login. You may need to go to "settings" to do this, or you may need to right click on your network and select "Properties" or "settings". Reboot computer. You should connect automatically (it can take up to two minutes). If you still have trouble, in the computer, temporarily turn off your computer software firewall, and see if that helps.
If the above does not fix your problem, download and install the latest driver for your wireless card.

LAN and WLAN not working

I'm working on a 64 bit HP Pavilion windows 8.1 OS.
The LAN and WLAN are not working properly. At first neither worked. After uninstalling and reinstalling the drivers the LAN worked, until I disconnected and reconnected the cable to the computer. After running sfc /scannow through windows 8 bootable cmd the WLAN would do the same as the LAN. It would connect, but after disconnect it wouldn't work properly. I checked to see if it was pulling an valid ipv4 and technically it is. It is pulling a 63 and not a 169. Although when hardlined it should pull a static ip of 50.115.146.xxx, but it is not.
I have run several Malware scans using Malware Bytes and have not turned up anything. I also did a Spyware scan using adwcleaner. I tried AML registry cleaner and junkware removal tool. I also tried netsh winsock reset and ntsh int ip reset C:\...
This topic first appeared in the Spiceworks Community

Go to Toshiba download page - http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp
There search for your notebook model and install chipset driver, card reader, LAN driver and WLAN driver you can find on Toshiba WLAN portal on http://aps2.toshiba-tro.de/wlan/
If you dont want to tell us which A100 do you have exactly you must search these drivers alone.
Good luck.

C6 wlan not working

my c6 not yet completed 7 days.but though shows available wlan network previously connected with but today while connecting shows selected wlan not found though it's working in my PC.i have restored factory settings but not solved.pls help me.

In my office network all mobiles of diffrent brands are connectied to same router and serf net and other facilities properly excep my Nokia C6, it conect properly after entering key, conection does not break any wheir show full antena but still i cant surf net and use any facility regarding wlan usage. At the same time in my home i can acces all the things.
I dont know what is the problum and how to resove it without tuching the router settings?

S920 wlan not working

Hi,
I have an S920 and wlan is not working . The icon is continuously blinking. I cannot enable or disable it.
Tried factory reset but the problem did not resolve.
I think I have the latest version because I recently downloaded a system update. Android version is 4.4.2.
Is the update the cause of this? Is there a way for me to revert to the old one?
Please help.
Thanks.

Nokia is the host of this forum, however the forum operates and functions with the participation of common folk, users from all over the world that either share passion for Nokia or are looking for support and answers from other community members...if you want to complain to Nokia there is a : Contact us - button on top right of this page...if you want to try to find answers patience sometimes is a virtue....now the issue of untrusted software, there are applications and sometimes themes that you have installed on your memory card/mass memory that will give that message when you go to application manager it will list the apps that are installed and that are not installed on your device, you can either install them manually or remove them from your phone, the next time you restart your phone you should have no problems with those messages. now the WLAN issue i am not sure about and I am almost certain it has nothing to do with your untrasted software messages.
You know what I love about you the most, the fact that you are not me ! In love with technology and all that it can offer. Join me in discovery....

Wlan not working in win 10 in hyper v

hi ,
I have installed Windows 10 preview in my Hyper V using Windows 8.1.
i have followed this steps in these urls
http://blog.credera.com/technology-insights/microsoft-solutions/using-your-windows-8-wireless-connection-inside-hyper-v/
http://blogs.msdn.com/b/virtual_pc_guy/archive/2008/01/09/using-hyper-v-with-a-wireless-network-adapter.aspx
But the WiFI Isnt working in Windows 10 guest OS.
Im getting network as limited and its not working.
How i can set it up
Thanks
Thank You , Shan Ali Khan

Hi Shan,
For this blog:
http://blogs.msdn.com/b/virtual_pc_guy/archive/2008/01/09/using-hyper-v-with-a-wireless-network-adapter.aspx
You may need to another thing :
1. configure an IP for that "internal virtual switch"
2. configure an IP for VMs which connecting to that internal virtual switch
3. configure Internal virtual switch's IP as the gateway for virtual machines connecting to that internal Vswitch
(the Gateway and VM's IP should be in same subnet)
Please refer to following thread ：
https://social.technet.microsoft.com/Forums/en-US/d380e4c3-a9c0-483f-8fd9-11962b1f486c/enable-virtual-machine-to-access-internet-with-ics?forum=winserverhyperv
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .
Thanks it worked for some time. Actually My DNS Server IP Changes when my router restarts.
Any there any way to setup without DNS i tried but the internet on windows 8 host becomes poor. ?
Thank You , Shan Ali Khan

WLAN not working under Windows XP on Satellite U400

After installing Windows XP Recovery on my U400 the WLAN is not found. Under Win Vista it was working properly.
There is no module listed under the device manager - searching after new hardware gave no results. It seems that the WLAN Interface is not recognized by Win XP.
The Communication switch at the front was "ON" - bluetooth is working correct.

Hello,
the problem with my notebook is the following:
I bought the notebook with 3 GB Ram. With Windows Vista everything worked fine.
With XP there is a problem with adress ressources. Everything above 2 GB Memory allocates new adress ressources. So in the device manager there is an device "PCI Express port 6" or something like that wich is shown with a warning. This device conflicts with the wireless adapter - so no adapter can be found. If i remove 1 GB (whatever combination) the adress conflict is resolved and the wireless adapter is working.
Thanks to my local notebook dealer (notebook shop in Darmstadt/Germany) for discovering the problem.
I now switched back to vista and everything works with 3 GB. (Memory was more important to me than having XPinstead of Vista).
I think the problem can be solved with a new bios update!
Regards - Felix

10.4.2 and WPA Enterprise NOT working

Dears,
I have 2 machines configured in this way:
- 10.3.9 with Airport card (no Extreme) and latest Airport drivers;
- 10.4.2 with Airport Extreme card and latest Airport drivers;
I try to connect to our WPA Enterprise wireless network and i got 2 different results:
- 10.3.9 connects and works;
- 10.4.2 returns an error, the logs show the following:
2005-08-18 13:23:17.601 SystemUIServer[380] EAPOLControlCopyStateAndStatus failed for "en1" (err = 6)
There was an error trying to get authentication status: 6
com.apple.network.EAPOLController not active
Before upgrading to 10.4.2 the same machine with 10.4.1 was able to connect to WPA Enterprise.
I further investigated on this, seems that under 10.4.2 the folder /System/Library/SystemConfiguration/EAPOLController.bundle is empty, while under 10.4.1 it contained some files (oh yes, I have the disk image of the workstation when it had 10.4.1).
Maybe the guru guys from Apple can see if the 10.4.2 updater deleted those files in error.. bye !

Hi Rick,
I did the following:
- Re-install 10.4.2 upgrade;
- Re-install Airport 4.2 upgrade;
- Repair permissions;
- Check Keychain.
I still got those errors in the logs:
2005-08-19 16:01:07.966 Internet Connect[280] EAPOLControlCopyStateAndStatus failed for "en1" (err = 6)
There was an error trying to get authentication status: 6
com.apple.network.EAPOLController not active
2005-08-19 16:01:07.971 Internet Connect[280] EAPOLControlCopyStateAndStatus err = 6
com.apple.network.EAPOLController not active
Using Internet Connect I can see our wireless network, that is correctly identified as being encrypted with "WPA Enterprise" but after I entered user/password I got the following error:
"WPA Authentication failed. There was an error trying to get authentication status: 6"
I double checked username/password, mac address, base station configuration (Cisco AP-1131) and Radius server, are all ok (the other mac, with 10.3.9 joins our WPA network succesfully).
I'm stuck here..

C3 WIFI - WLAN Not Working (Solution)

Hi If You Have Bought C 3 And Not Able To Connect With WIFI Or WLAN And The Given Error Is Showing :
* Service Not Available
The Error Is Coming Because Your WIFI SHaring Settings Are Not Proper
To turn your Wi-Fi enabled personal computer into a wireless hotspot to share your Internet connection, and create wireless networks on the fly with your friends, co-workers and other devices. Connectify can even share Wi-Fi networks which you are currently connected to with a single Wi-Fi card.
http://download.cnet.com/Connectify/3000-18508_4-75024171.html?part=dl-10061477&subj=dl&tag=button
Download This Software In Windows 7 OS And And Search WLAN In Nokia C 3 U Will See The WLAN Working .............Enjoy...

i hv windows xp prof. ....whenever i try to connect my nokia c3 to my "nokia siemens networks" modem ...it connects but when i try to surf internet it says"service is not available" .......please help!!!!!....my modem is RESIDENTIAL ROUTER 1600

WPA, WPA2 not working, only WEP.

Hi everyone,
First off i'd like to say that i've done alot of searching and cannot for the life of me figure out why i can't configure my router to have working WPA or WPA2 security, only WEP seems to be a working option. Up until today i've had a WEP key, but feel WPA or WPA2 would be more secure, as I live on campus at a university. I have a D-Link DI-624 router, and am running 10.6.4. I tried both DHCP and manually entering IP addresses, but it all comes down to the fact that i keep getting either "Airport has a self-assigned IP address and may not be able to connect to the internet." or ""Airport does not have an IP address and cannot connect to the internet." Usually when I can get it to connect after trying over and over, the airport will give me either of these messages and results in 169.254. . being the assigned IP address causing the conflict. I will answer any questions necessary to resolving my conflict. Any help is appreciated.

It appears the firmware update is a temporary fix, as the router will keep working for a while, but every so often it will just connect to my wpa2 security enabled network, but will only give me the "no ip address" message or the other message that indicates i can't connect to the internet. my fix to this is to simply reset the router with the pin-sized button in the back, thus having to re-create the network and add all the details again. anyway i was wondering if any one could offer any more insight on this problem. it is very frustrating to keep resetting the router every two days just to connect to the internet. any help is appreciated.

E60 - Wlan not working

Hi, the wlan on my E60 RM-49 stopped working some days ago, and I'm not able to restore it.
I have reset the default phone options, reinstalled the latest firmware available (3.0633.09.04).
When I search for wlan the phone doesn't show any wireless connection, the sames that worked just some days ago.
Is an hardware problem? What test I can make?

If you can't see any available WLAN in the conn.mgr, I suggest you reset the phone, dial *#7370# 12345 reformat, you'll lose all data. Make a backup first and restore without the settings. If that wan't work, you better bring your E60 in for service.
http://europe.nokia.com/support/product-support/nokia-e60/user-guides
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

Internet and WLan not working on Satellite U400 Win XP

Hi all, please help!
I just bought my new Sat U400 and I am trying to install Win XP and it went quite well till I wanted to have internet and stuff... no internet connection with cable, neither with wireless.
I tried to find drivers but I have no idea what I need to look for, since I have no devices detected on my computer... the bluethooth i am already afraid of, since i ve never even used it before :D
I know something like wlan 802.11/a/b/g/N-draft in the parameters of my computer but that s all.
And to be honest i have no idea about what it should be so pleeease someone help me!
thanx
annamarie

Hi,
Yeah, thanx a lot for both of u! Finally I found all the drivers :) i was just not sure of their type... now it s ok. thanx again.
And i also had a problem with my battery, i just couldn t charge my battery even if it was plugged in for a whole night, but as i read and as i did, after having a BIOS update everything became really fine (maybe this can help others...)
I just can t understand - not any complaint or nothing but - if i buy a computer from a company super huge and good like toshiba why do i have to do a bios update myself??? i mean, shouldn t the company give u the newest and best stuff whatever? i don t care, anyway, i m really happy now, my computer works very well, it was worth the things to do for a day to finally have this fine stuff. :D
now it s only trying to figure out how to make the controls function with winamp... :D i can turn winamp on with the buttons of toshiba (i downloaded a plugin) but i cannot switch songs or pause/stop etc. any ideas? ;)
cheers anyway for all
annamarie

WPA Enterprise Not working in MAC

I have install the Cisco 1131 ap with acs 5.0
I have configured AP with WPA with Radius Authenticationable
All Windows 7 & XP user connected
MAC user is not connected
there are two option wpa enterprise & wpa2 enterprise

hello
on your ACS 5 access policy for wireless, check that EAP-GTC is allowed under "allow PEAP" in the "allowed protocols" section.
hth
andy

E61i WPA Wlan not working

Similar Messages

Maybe you are looking for