E63 dead. need to access memory

Hi, there has been a battery leak in my E63 that most likely permanently damaged the phone. the service centre already deemed it unfixable and now when i try to switch it on it vibrates, reaches as far as the nokia screen, keeps blinking then dies.
I'd like to know if there's anyway I can possibly access the data saved on my phone memory, such as contacts for example. I have a USB cable, but Nokia Suite would not connect to the phone in its current state. Any help would be appreciated, thanks a lot.

Did you try with the charger connected? I guess you must at least turn the device on to retreive data from the phone  memory. If your data is very important to you I suggest you bring your E63 in at a Nokia Care Point.
http://europe.nokia.com/support/repair-and-recycle/repair/care-points
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

Similar Messages

  • The circuit of my macbook is dead yet the hard drive is fine.  I need to access a file from the hard drive, how can i do this? is there a cable i can connect to another mac that will let me transfer the file?

    The circuit of my macbook is dead yet the hard drive is fine.  I need to access a file from the hard drive, how can i do this? The mac turns on the screen freezes as bright blue.  Is there a cable i can connect to another mac that will let me transfer the file?

    There is another option if the Macbook will start up in Target Disk Mode.
    Restart the computer while holding down the T key. If you see the firewire symbol moving around on the screen you can connect this one to another one in TDM. You will need a suitable cable to connect the two Macs.
    http://support.apple.com/kb/ht1661
    Firewire symbol:

  • I need to access (Ultra) scsi-2 drives but the card is dead. Is there an adapter/converter out there somewhere like my IDE to USB for this? Any other suggestions appreciated.

    I need to access (Ultra) scsi-2 68 pin drives but the card is dead. Is there an adapter/converter out there somewhere like my IDE to USB for this? Any other suggestions appreciated.

    Might be hard to find, but long ago there were a couple of Firewire<->SCSI adapters, if you have USB2 those might be available also...
    http://www.ratocsystems.com/english/products/FR1SX.html
    http://www.ratocsystems.com/english/products/U2SCX.html
    http://www.ebay.com/sch/i.html?_sacat=0&_nkw=scsi+to+firewire&_frs=1
    I think Belkin made one also.
    Might be far cheaper to buy an old Mac or even PC with SCSI.

  • HT1661 My mid-2009 MacBook Pro has just died via a painful (for me) hard drive failure. I backed up a good percentage of files recently but not enough to keep me happy.  I need to access the dead drive on the MBP via a 2008 iMac. Best options?

    My mid-2009 MacBook Pro has just died via a painful (for me) hard drive failure. I backed up a good percentage of files recently but not enough to keep me happy.  I need to access the dead drive on the MBP via a 2008 iMac. Best options?
    I have ordered a 800 firewire to 800 firewire cable and am hoping to use the target mode option to copy files from the MBP.
    Is this possible?
    Hope so!
    Any advice and or help would be greatly appreciated.
    Many thanks,
    Neil

    Thanks Ogelthorpe.
    Just bought an enclosure to try that also.
    Hoping the MBP isn't really dead but just feigning death
    Fingers crossed.

  • I desperately need to access my User Library folder in Time Machine (Lion so = not visible).

    Hi. I installed Lion a few months ago and got a new external drive to back up Time Machine.
    Nobody told me the User Library would be made hidden in the new OS. I have been backing up regularly in the belief that all my work, settings and so on was safe.
    Yesterday my iMac (27" 2.8 Ghz Core it with 4 gib memory) suddenly went mad. Message saying finder had quit whilst trying to restore windows. Desktop was flashing, no icons clickable, no external disks readable. Could access some progs and terminal, but nothing else. Could not get into the history folder to trash various plists and so on as the folder is hidden and the alt Go wouldn't work. The Finder just wouldn't do anything.
    I have sorted it out BUT I have lost my address book entries, my browser booksmarks, my desktop shortcuts and my iCal entries. I need to access my User Library on my Time Machine. Is there a way?
    I cannot believe I have been religiously backing up my stuff but Apple has made it so I can't access my backup of one of the most important folders on my Time Machine???
    Is there anyway of getting into this from Terminal or something? I will never be able to get back all the bookmarks and stuff I've been researching for years. I have it backed up on two different hard drives, both of which have 'invisible' library folders. I have make the folder visible now, for future backups, but it's after the horse has bolted. I am furious, and just feel like bursting into tears because of all the time it's going to take me to get all my work back. I can't tell you how stupid this was, Apple.
    If someone could help I'd be really grateful. I've got older backups but they are so old they won't get back my recent stuff.
    Thanks.

    select Finder
    hole option key and select Go in the menu
    Select Library
    Enter Time Machine
    You should be seeing all the versions of you Library folder.

  • IMac died - need to access iWeb

    My iMac died and I need to access my .Mac account on my mac book. But I can't get to it from iWeb. I don't have the Domain file from my iMac, because it's dead. How do I access and publish from iWeb on my living mac book?

    http://iwebfaq.org/site/iWebBackupretrieve.html

  • Need help accessing the router web page.  I have been tol...

    Need help accessing the router web page.  I have been told my router is acting like a switch and the IP address is not in the proper range.  I have tried reseting the router (hold for 30 sec and unplug for 5 mins).  Didn't work.
    thanks

    What router are you using?  Almost all Linksys routers use 192.168.1.1 as the default local IP address, but there is at least one that uses 192.168.16.1 , namely the WTR54GS  (not the WRT54GS).
    You need to try again to reset the router to factory defaults.
    To reset your router to factory defaults, use the following procedure:
    1) Power down all computers, the router, and the modem, and unplug them from the wall.
    2) Disconnect all wires from the router.
    3) Power up the router and allow it to fully boot (1-2 minutes).
    4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
    5) Power down the router.
    6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
    7) Power up the router and allow it to fully boot (1-2 minutes).
    8) Power up the computer (if the computer has a wireless card, make sure it is off).
    9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
    10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank (note: a few Linksys routers have a default user name of "admin" (with no quotes)), and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
    If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
    If you cannot get "Reply from ..." in step 9 above, your router is dead.
    If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
    If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
    Please let me know how things turn out for you.
    Message Edited by toomanydonuts on 01-21-2008 04:40 AM

  • My iphone has failed and I need to access my contacts.

    My iPhone has failed (again) and I need to access my contacts.  I backup/sync to ITunes regularly, but I can't find any means to access the data that I have backed up.
      Any thoughts?
    B.

    The iphone is designed to be synced woth your computer regularly.  Your contacts should reside on your computer.  The iphone simply allows them to be portable.
    Your contacts will be in whatever program you have been syncing.
    The backup is only for restoring an iphone.  Contacts are backed up to keep the recents and favorites when you restore your iphone.

  • I need to upgrade memory slots on my Mac mid 2010 up to 4 GB module which is currently 2GB with two different 1GB memory  slots.Is it compatible and would like to know about the cost?

    I need to upgrade memory slots on my Mac mid 2010 up to 4 GB module which is currently 2GB with two different 1GB memory  slots.Is it compatible and would like to know about the cost?

    this sub forum is about running windows on macs maybe you should try
    https://discussions.apple.com/community/notebooks/macbook

  • HT201303 How do I set up my iPhone so that I have to enter my password each time I need to access my apple account? Previously my account name was always stored and I only had to enter my password each time but now it never asks for a password

    How can I set up my 4s so that when I need to access my apple account to either download an app, update an app or buy something then I need to just put in my password?  This is how my 3s worked but the 4 s seems to have stored all my details so I don't need to log in. My young son sometimes plays games and I dont want him to accidentally buy stuff. If I log out then each time I need to go back in I have to put in all my account info. Not just my password.
    Any ideas?

    Depending upon what version of iOS that you have on it then you might have a Settings > General > Restrictions > Require Password setting on it - if you do then set it to 'Immediately'

  • Need to Access the dvd on another computer

    I need to access a dvd player on another mac to install some software and i have followed the apple instructions below for sharing another computers dvd and everything works until its time for me to select remote disk under devices...there is nothing there to select...The other mac shows that it is sharing it dvd player...the internet connection is working as i am able to share that computers screen but cant get it to provide me with "remote disk"...any thoughts?? I do not have an internal DVD player it has been turned into a second hard Drive...thank again
    To access a DVD or CD on another computer:
    Make sure both computers are on the same network (wired or wireless), and the DVD or CD Sharing software is installed on the computer with the optical drive.
    Make sure the computer with the optical drive is set up to share the disc.
    On a computer with Mac OS X v10.4.10 or later: Choose Apple menu > System Preferences, click Sharing, and then select the “DVD or CD Sharing” checkbox. Select “Ask me before allowing others to use my DVD drive” if you want to be notified when a computer tries to access the drive.
    On a computer with Windows XP or Vista: Open the DVD or CD Sharing control panel and select “Enable Remote DVD or CD.” Select “Ask me before allowing others to use my DVD drive” if you want to be notified when a computer tries to access the drive.
    Insert the disc into the optical drive.
    On the computer without the optical drive, select Remote Disc under Devices in a Finder window sidebar. If you see the “Ask to use” button, click it.

    If you are using two Macs you can try to do this via Target Disk Mode. Info here:
    http://docs.info.apple.com/article.html?artnum=58583

  • How do I move a movie I have synced from iTunes into the "Movies" tab of the Video App? I need to access a slideshow I made in IMovies and may not have WiFi. I did it once, but can't figure out how to do it again! The file is an m4v. Thank you!

    How do I move a movie I have synced from iTunes into the "Movies" tab of the Video App? I need to access a slideshow I made in IMovies and may not have WiFi. I did it once, but can't figure out how to do it again! The file is an m4v. Thank you!

    Im just guessing but it seems like you would have to get your movie into the correct folder on a computer then use iTunes to sync it to your iPad. If you've synced to a computer and have movies then on your computer should be a folder with the movie in it. You could export your iMovie to something like Dropbox then download from Dropbox to the folder you think it needs to be in the sync your iPad again. Again this is just a guess. Others may have a better answer.

  • HT201210 I need to access my iphone but I have forgotten my password. How can I access my iphone?

    I need to access my iphone but I have forgotten my password. How can I access my iphone?

    You need to restore iPhone with iTunes on computer. Open iTunes on computer, connect iPhone to computer, hold both home and power buttons until iTunes recognizes iPhone in Recovery Mode. Click Restore button of iTunes.

  • I have two apple accounts, but can only access one. I did all the steps to recover the older account's password but nothing worked. I need to access the older account to update apps. Also would there be a way to just combine both accounts?

    I have two apple accounts, but can only access one. I did all the steps to recover the older account's password but nothing worked. I need to access the older account to update apps. Also would there be a way to just combine both accounts?

    Were you able to reset the account's password ? If not then how did you try to get it reset e.g. http://iforgot.apple.com (which would have sent it to the rescue email address if you have one on that account) ? You can also try contacting iTunes Support in your country to get it reset : http://support.apple.com/kb/HT5699
    And no, accounts can't be merged nor content transferred between accounts.

  • HT5621 I have moved permanently from the US to live in the UK. when I try to download a UK app I am often told that I cannot use a UK Apple sstore, only a US store. I need to access various UK stores how can I deal with this?

    I have moved permanently from the US to live in the UK. when I try to download a UK app I am often told that I cannot use a UK Apple sstore, only a US store. I need to access various UK stores how can I deal with this?

    Try here
    http://support.apple.com/kb/HT1311
    when you have UK Cards etc best to change as well

Maybe you are looking for