E65 not start-up after updated new firmware

Hi,
Yesterday I conected to PC suite and updated firmware from 2.0.... to 3.0... > Everything went through smoothly. After I restored all information from back up files of PC suite, then I could not use my phone any more. Everytime I try to restart my phone, the message " Phone start-up failed. Contact to retailer "
Could any one help me to make my phone back to work, please ? Thanks a lotttttt

Try the "3 finger deep reset" which is depress these three keys simultaneously "*" "3" "green phone" and then power on phone whilst keeping those same three keys depressed until you hear start-up tone.
This should ONLY be done if the device doesn't power up normally anymore and it wipes everything in the Phone memory that is not part of the ROM.
You will need to restore your data after this.

Similar Messages

New Macbook Pro does not start up after updating...HELP!!!

Hi,
My new Macbook Pro does not start up after it got updated. The first time I used it, it was perfect. I updated it and restarted it when it told me to but it doesn't boot. It shows an apple and a spinning circle when it turns on but that's it.
Can somebody please help me?

You should probably post your question in the MacBook Pro discussions:
http://discussions.apple.com/category.jspa?categoryID=190

Not starting up after updates

I just got a G3 iBook 500Mhz 384Mb off ebay, OS10.4.9, which worked fine. So I decided to install some of the available software updates, instead of just letting it be! A couple of iphoto updates, keynote, iweb, java, final cut, etc,went in fine until the 10.4.11 update which would not complete - got to 12% or something and then said an error was detected so it stopped. I stopped doing updates, my boy played an internet game for a wee while, then shut down. Now it won't startup - I get a tone, the spinning gear for 20secs or so, then the blue screen with the white box saying Mac OS X and an empty progress bar, and a while later the spinning beachball appears, to be with me for a few hours. Nothing else. Some suggestions please? (I also have a MacBook Pro, with 10.4.11, if that might be helpful, and while I'm not experienced at computers, I'm quite prepared to try things.
Many Thanks.

Oh.
Ah well. I'll get back to the seller - again. He earlier suggested 1. resetting the P-RAM, 2. resetting the open firmware, 3. safe boot. None of these worked. He then suggested booting from the disc(pirated) and reinstalling. This worked to an extent, but this morning it would not start up again - but it did get as far as the login, then after logging in it went to a background, with an arrow pointer, and no further (I did leave it for over an hour), while last night it did get past that point(slowly) and worked ok.
So, now I'm trying to reinstall again ( a smaller custom install) then I'll delete the most recent previous system folder, and some other apps that came with it (pirated too!!?)
I guess I may (should) buy a retail copy.
Why didn't I just leave it alone???
Any other advice?
Regards
Roger

Can't connect to internet after updating new Firmware wrt54g Help please!

So i just updated my firmware on my wrt54g ver 2 router, went through all the steps it updated successfully after that i hit the reset button and unplugged the router as tehe online instructions said to. Now i can't connect to the interent at all with either of my two wired computers or through the wireless. All the lights on the front of the router are on like the power, internet, and wireless connectivity. Also the the two WAN ports my computers are connected to in the router the lights are on and it's recognising them. But I can't connect to the internet or even see the router on my network settings. Somone suggested to reconfigure the router but when i go to set up new connection my computer doesn't detect the router and also i cant connect to the router using the ip address 192.168.1.1/ since there is no internet connection. Is there a way to get to the router options or a way to revert it to its old firmware. Any help would be much appreciated. I should after updating the firmare the power button is contantly blinking.

I am having the exact same problem.. I have the same router and same version as well.. I followed the directions and upgraded the firmware. it said update successfull and then I reset it and power cycled it to find that my network no longer works and I cannot access the router..I've looked through all the troubleshooting guides and they do not help.. It says if you can't access the web based page then to use the TFTP utility to re-flash the router’s firmware but it seems it cannot make a connection to the router.. I've tried to ping it like it says to in the TFTP guide but it does not seem to be able to make a connection to the router.. I tried to access Management Mode to recover the router and resume the loading of the firmware upgrade but I can't get the Management Mode Firmware Upgrade page to open as well.. So what gives? I followed the directions but the only thing I seemed to accomplish was to brick my router.. Does anyone have a clue on how to go about fixing this problem? Any help is appreciated..

Lightroom not starting up after updating to CC (2015)

Adobe CC updated my Lightroom CC (2014) to CC (2015) Now Lightroom will not start. I have uninstalled, rebooted, installed again and still does not start up.

Tstoikka did you utilize the uninstall process documented in Install and update apps - https://helpx.adobe.com/creative-cloud/help/install-apps.html to remove your current installation of Photoshop Lightroom? Are you able to install other Adobe Creative applications successfully?

Slim does not start lxde after updating

Hi!
After updating the other night I cannot log in to lxde anymore. Slim gives me
Failed to execute login command
I read my way through the internet for similar threats and problems. I already checked whether my slim.conf is ok. I checked whether X is running ok. And Im not sure if it is.
I did
grep -e "2012-09-19" /var/log/pacman.log
to see what was updated. And it was xf86-video-intel and tzdata and the kernel.
Im running arch on a eeepc 701 with intel graphics. I have Slim and lxde. I can ssh onto the machine from outside.
If I take slim from the deamons in
/etc/rc.conf
I can
startx
but I only get a black screen on tty7 and on tty1 I get
No protocol specified
. And after some time I get
xinit: giving up
xinit: unable to connect to X server: Resource temporarily unavailable
waitiing for Xserver to shut down Server terminated successfully (0). Closing log file.
xinit: server error
I noticed that I didnt have "i915" in /etc/mkinitcpio.conf, so I added that and built iniramfs. But that didnt help the issue.
Maybe anyone cand help me out here?
Thanks for your time!

It definitely sounds like something went wrong with your video update. Can you downgrade to confirm that is the problem? If so, my next thought would be to remove the recently downloaded version from your package cache and re-upgrade.
If downgrading doesn't help, then perhaps my assumption is wrong, then full Xorg logs would be useful. Actually, they'd be useful in either case ... so can you post those (or pastebin them and link to it).

Imac G5/Intel, OS 10.6., system does not start up after connecting new router

After connecting the imac to a new router the system hung completely up. After each input, e.g. opening preview or a browser, the coloured turning disc appeared and nothing happened anymore. Several restarts, also in safe mode, were unsuccessful. I could not switch to another user. Restart is only possible at all from installation disc but thereafter problem remains the same.
What can I do?

And, what happens if you disconnect the computer from the new router? Are you able to do this, and what happens when you try it?
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.

Mac book not starting up after update

after installing the latest update on Mountain Lion my Retina MBP dies after trying to boot. any help would be great.

Hopefully you have a backup. Your hard drive may be failing. I'd try a few things:
if you have any peripherals, like mice or keyboards, unplug them and try again.
try a SMC reset Intel-based Macs: Resetting the System Management Controller (SMC)
a safe boot Mac OS X: What is Safe Boot, Safe Mode?
boot to your recovery partition and repair your hard drive and permissions When to Run First Aid in Mountain Lion's Disk Utility - For Dummies
if that doesn't work, try internet recovery OS X: About OS X Recovery
if you can get your computer booted in one of the recovery modes, but it can't be repaired successfully enough to start into the regular boot partition, you may need to erase the drive and start over with a clean installation.
You might be able to get your hard drive to mount in target mode on another mac, which would let you back up any files that you want to save on the drive: OS X Mountain Lion: Transfer files between two computers using target disk mode
if you can't get any of this to work, then the drive quite possibly is failing, and should be replaced.

Computer not starting up after updates

I updated the software on my computer and restarted the computer. When it came back up it said i needed to shut down my computer for the firmware and when i was turning it on, i should hold the power button until it flashed. I did this and the computer will not turn on. I don't have a clue as to what happened and any advice would be great.

Try this: Resetting the System Management Controller >>
-Bmer
Mac Owners Support Group
Join Us @ MacOSG.com
iTunes: MacOSG Podcast
 An Apple User Group 

Apple TV not starting anymore after update

My Apple TV is set on applying updates automatically. When I started it yesterday it showed a message that an update had failed and encouraged me to perform the update manually. I did so in the settings and everything looked normal. The updated was first downloaded and then the installation performed however at the end of this task the Apple TV shut down and now I cannot start it at all anymore. Holding down Menu and Down on the Apple Remote for six seconds does not work either.

If you really want to restore your system [this link|http://docs.info.apple.com/article.html?artnum=61802|How to restore your Apple software] might be of some help... It boils down to this:
*Restore Mac OS X and all bundled applications without erasing the Mac OS X volume*
1. Back up your essential files. This is a wise precaution even though you won't be erasing the volume.
2. Insert the Mac OS X Install disc that shipped with your computer.
3. Double-click "Install Mac OS X and Bundled Software."
4. Follow the onscreen instructions to reinstall all software.

Language question after update new firmware 200.21...

Hello,
I would like to update my Nokia E71-2 (code 0569371 RM-357) to the latest firmware v 200.21.118, but before I do it, i want to know about which languages it contains in this firmware, dose it contains the French language?
Thanks very much for your help

The firmware update will contain a language pack specific to the region your phone is coded for.
So if your phone was bought in france from a reputable french retailer, then it should have the appropriate product code and french should be included in the update

ITunes not starting up after update, errors showing

I recently received an updated iTunes and I'm getting two errors from previous issues.
I have tried every single step with uninstalling, then reinstalling the program. As well as removing a previous issue that has happened before to no avail.
Can this issue be fixed with the updates?
I'm on Windows XP without a iPod Touch

ok THANKS so much!!
it now works!!
First I removed iTunes.app from my system using these instructions: http://www.tekrevue.com/tip/uninstall-itunes/
Next I opened the App Store and it showed me iTunes under "Updates".
I reinstalled iTunes via the App Store and now I can launch iTunes as expected.
Because I didn't delete the iTunes folder inside my user's folder, all my content remained.
thanks to you :
uwe eberhard

Firefox does not start up after an automatic update. Every time i try to open it, it just prompts the Mozilla Crash Reporter.

Firefox does not start up after an automatic update. Every time i try to open it, it just prompts the Mozilla Crash Reporter.
''Add-ons: {972ce4c6-7e08-4474-a285-3208198ce6fd}:3.6.10
BuildID: 20100914125854
CrashTime: 1290192405
EMCheckCompatibility: true
FramePoisonBase: 00000000f0de0000
FramePoisonSize: 65536
InstallTime: 1287124738
ProductName: Firefox
ReleaseChannel: release
SecondsSinceLastCrash: 422
StartupTime: 1290192405
Theme: classic/1.0
Throttleable: 1
Vendor: Mozilla
Version: 3.6.10
This report also contains technical information about the state of the application when it crashed.''
Same thing happens when i click restart.
No difference when i run it in Safe mode. And it won't let me create a new profile either. Is there anyway else i can extract my bookmarks? This is driving me crazy!

Did the crash reporter send any crash reports? 
You can see the crash reports in this folder:
"C:\Users\<user>\AppData\Roaming\Mozilla\Firefox\Crash Reports"
See: http://kb.mozillazine.org/Breakpad
See also [[Firefox crashes when you open it]]
Create a new profile as a test to check if your current profile is causing the problems. 
See [[Basic Troubleshooting#Make_a_new_profile|Basic Troubleshooting: Make a new profile]] 
There may be extensions and plugins installed by default in a new profile, so check that in "Tools > Add-ons > Extensions & Plugins" 
If that new profile works then you can transfer some files from the old profile to that new profile (be careful not to copy corrupted files) 
See http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox 
If that still causes the same problem then do a clean reinstall and remove the Firefox program folder.
* Download a fresh Firefox copy from http://www.mozilla.com/firefox/all.html and save the file to the desktop.
* Uninstall your current Firefox version and remove the Firefox program folder before installing that copy of the Firefox installer.
* Don't remove personal data when uninstalling.
* It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
See:
* http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Clean_reinstall

Apps not working with docomo after updating new sw...

hello brother,
i have updated my nokia c2-00 sw v3.99 .
After updating new sw v.3.99 my apps not working with tata docomo only .
Docomo is my personal sim-card.
What can do for get ride it.
Solved!
Go to Solution.

Hello, Premkoli. Which specific apps are you referring to? Are these apps downloaded from the Store, or preloaded ones? When you say 'my apps not working with tata docomo only', does it mean that these apps work with other SIM cards aside from TaTa Docomo? How did you update your Nokia C2-00? Is it by going to Settings > Phone > Device Updates > Check for updates, or via Nokia Suite?
Since the issue started after the software update, you can try to reinstall the phone's SW via Nokia Suite. Just download it on your PC, and then connect the phone via a compatible USB cable. After that, launch Nokia Suite, and the go to SW Updates > Device Software Updates > Reinstall current SW. After that, try opening the same apps and see if they'll work with your Docomo SIM card. Get Nokia Suite from this link: Nokia Suite
Let us know the outcome.

After updating the firmware on IOS7 I can not activate my iphone 4.

After updating the firmware on IOS7 I can not activate my iphone 4. Itunes says "Unlock the iPhone on this ***** @ *******. ru impossible"

ITunes says:
At the moment the iPhone is tied to the Apple ID (i ***** @ y *****. Ru). Sign in with Apple ID, which is used to configure this iPhone.
Unlock iPhone on this I ***** @ ya *****. Ru impossible.

E65 not start-up after updated new firmware

Similar Messages

Maybe you are looking for