E7 battery charging with USB connected

With E7 connected via the USB cable to the PC it shows up as charging the battery if its not full. However after 2 - 3 hours the E7 shuts down on the basis of having a depleted battery. Can I expect the USB connection to keep the charge stable when connected to the PC or am asking too much?

Looks like the Battery controller is not quite communicating with the battery itself, a possibility of a 3rd Party (un-original) Battery installed (happens all the time with Refurbished stuff you buy these days) So my only suggestion would be to either get the Unit diagnosed by Nokia Care Centre OR get another Unit. Oh and avoid 3rd Party repair centres... a question of Quality versus Quantity here gents. Cheers.

Similar Messages

  • Will not charge on any charger, will charge  with USB connected to PC

    iPod Classic (60 GB Photo) will not charge on ANY charger - usb, firewire or car charger, I tried multiple versions of all of them, but it will charge when connected to my USB port on my PC.
    When connected to a charger, is shows that it is charging but it doesn't. It doesn't matter if the battery is dead, 1/2 charged or 3/4 charged, it leaves the iPod battery in the same state, not charging at all, no matter how long it is left connected.
    It charges perfectly normally when connected to a USB port on a PC.
    It's not the chargers not the cables since I've tried different ones.
    HELP!

    I have the same problem with ipod nano.
    When I connect itt o mains USB charger the ipod switches on and is in pause mode but appears to be charging.
    After a few minutes the ipod switches off and the screen is just black with no charging indicated.
    If I set it to play then after a while the charging logo goes off and it just runs on the battery until it is dead.
    If I switch off the ipod then it goes to black screen.
    This is different behaviour from connecting to USB on a computer, where the
    charging persists. Even if you switch the ipod off then it still shows a charging logo.
    It seems like the computer is supplying a signal to keep the ipod awake and that it does not get from the mains USB supply.
    Steve

  • My Mac Mini will charge - but not sync with - USB-connected devices (ipod, camera, memory card reader). How do I fix it?

    My Mac Mini will charge - but not sync with - USB-connected devices (ipod, camera, memory card reader). I have tried unplugging the devices, restarting the computer, selectively unplugging and plugging in the devices, closing and opening the relevant applications (iTunes, iPhoto, etc). I have tried using different USB cables.
    It's like all of a sudden the synching service stopped functioning or recognizing these devices for some reason. The other ports work just fine (monitor).
    The only USB-connected external device that appears to be unaffected is the USB SuperDrive and it works on all the USB ports into which I plug it.
    How do I fix this?

    Open Console in Applications>Utilities & see if there are any clues or repeating messages when this happens or doesn't happen.

  • My iphone5 wont charge with usb port but works fine with wall plug... Infact computer. Doesn't recognizes the iphone

    Battery not charging with usb port but works fine with wall plug.. So the prob is computer is not detecting the iphone5 . This problem started after upgrading to 6.1.3 version

    Try to see what happens on another computer. If it works on another computer, the issue is not at the iPhone.

  • Battery charging by usb port on PC and adapter which is better

    Please help me
    Battery charging by usb port on PC and adapter (enclosed with IPHONE box )which is better?
    Regards

    Adapter is probably quicker as you have slightly better power than from a USB socket

  • Get "using too much power" message when charging with USB

    I have a 4th gens iPod Touch that appears to have a number of issues:
    1. get "using too much power" message when charging with USB
    2. can't re-boot
    3. unable to access iCloud Backup, Ignore and Settings button inactive
    4. unable to unlock unit when using the Home button to turn the unit on

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable                                                       
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • Only charge with USB to PC

    The phone does not charge when using the wall or the car charger. It charges with USB plug to a PC. This happened after OS4 upgrade. Does anyone have the same issue? Ken

    Same here. Any solution?
    3G - OS 4 - Windows xp
    Message was edited by: Tato_c

  • Any network adapters with usb connection for mac?

    Hi!
    Sorry if this is posted in the wrong forum/section. But I need a better network adapter than what comes with my macbook. I need an adapter with usb connection. Found a lot of them, but only for windows Any software that can take a windows driver and "merge" it to the airport software on the mac os x?

    Hello johannesharestad. Welcome to the Apple Discussions!
    Other World Computing (OWC) carries a number of OS X-compatible USB wireless adapters that you many want to consider.

  • Why does my ipod not charge with usb hub in wall outlet?

    why does my ipod charge on my computer
    not charge with usb hub in wall outlet?

    Because the hub is not compatible with the iPod.
    Just use your computer or purchase a wall charger.

  • I have mac book pro and recently changed to Lion.  since then it will not recognise my epson r2880 printer telling me it is not connected when it plainly is with usb connection?

    I have mac book pro and recently changed to Lion.  since then it will not recognise my epson r2880 printer telling me it is not connected when it plainly is with usb connection?

    Turn off your printer.
    Go to System Preferences > Print & Scan > Printers window and delete the printer from the list, then add it back.
    Turn on your printer.
    Any difference?
    Here are some more tips from Apple Support article.

  • Iphone while getting On showing itunes logo with usb connection

    Dear Sir,
    I was upaditng my iphone 4s for from IOS 5.1.1  to IOS 6.1.2 by connecting with a personnel hotspot wifi connection. While doing this my iphone got switch OFF and then automatically got ON and the showing " Itunes logo with usb connection with up arrow".
    Also i tried to switch OFF and ON 2  to 3 times but still showing same.
    Can you please assist me , what i have to do now, to get my Iphone ON as normal like before.
    Awaiting for your quick response,
    Thanks and Regards,
    Vishal Haswani.
    <Personal Information Edited By Host>

    Connect to iTunes on the computer you usually Sync with and “ Restore “...
    http://support.apple.com/kb/HT1414
    If necessary Place the Device into Recovery mode...
    http://support.apple.com/kb/HT1808
    Note on Recovery Mode:
    You may need to try this More than Once...
    Be sure to Follow ALL the Steps..

  • HT201210 my new iphone 4 is stuck with "USB connect to itunes".  I put it in recovery mode last night, but it doesn't change.  Itunes recognizes the phone and says it's in recovery mode, but when I do a restore, nothing changes.

    my new iphone 4 is stuck with "USB connect to itunes".  I put it in recovery mode last night.  Itunes recognizes the phone and says it's in recovery mode, but when I do a restore, nothing changes.

    it says "itunes has detected an iphone in recovery mode.  you must restore this iphone before it can be used with itunes."  I click OK
    then I click the restore button
    Then the box says "Are you sure you want to restore the iphone to it's factory settings?  all of your.....etc."  I click Restore and Update
    then it goes into software update
    at the end of the software update it says "Itunes has detected an iphone in recovery mode...."
    All this time, the screen of the iphone stays on with USB to Itunes
    I might add that while the phone was in it's first attempt at recovery mode, it was accidentally unplugged.
    any suggestions?

  • Is charging iPhone 4 with USB  connection in 2012 Toyota Sienna safe?

         Is charging iPhone 4 with the USB connection in 2012 Toyota Sienna safe?

    Sure. I have been using the USB charge/music interface in my Toyota truck with my iPhone for almost 2 years, with no issues.

  • 3rd Gen Battery Drain With USB

    Hi, I charge my ipod with the wall adapter with firewire cable and it holds a charge (as well as a 3rd is expected to) and when I recently hooked it up to my new laptop with the usb cable to get my music, the ipod battery goes dead after several seconds and the ipod shuts down. Bat. life as normal if not hooked up to pc. I used a pc with same operating system and cable in past and worked fine. Please help!

    The 3rd gen iPods do not charge via USB. They require a built-in 6 pin FireWire port on your computer (and the necessary connecting cable of course) or the FireWire iPod Power Adapter.

  • IPod Nano 1st Gen Wont Charge With USB Cable

    I just purchased a brand new 4 gb white 1st gen iPod nano. From the moment I took it out of the packaging and tried to charge it with the provided USB cable I noticed it was not working. No response at all, nothing was getting into the iPod. I tried multiple USB cables with equal luck.
    I have a Dension I.C.E Link Plus in my car, I figured I'd try it, sure enough the iPod Nano began charging and booted up. I finished charging it to a full charge in my car.
    After a few days of use, I went to charge my iPod via USB cable and when I plug it in, it connects to the computer I can transfer songs perfectly but it constantly states that the iPod is "charged" displaying the plug battery icon not the flashing thunder bolt. So I figured it was charged, when I unplugged it from the USB cable the battery meter was clearly not charged.
    So, I assumed it was my computer USB ports being messed up so I purchased a A/C Wall Charger Adapter. Once again it would only display "charged" so far the only thing that will charge my nano is my car.
    With the A/C wall charger I have even tried multiple cables with no luck.
    CAN SOMEONE HELP ME!?!?!? I thought it was suppose to charge with the provided USB cable? Thanks!

    Yes you have a one year warranty from the date of purchase from Apple. Go to this link and on the bottom right hand side it will ask you to enter your serial number and will tell you if you are still under warranty. http://www.apple.com/support/
    If you are you can take it to a Apple store, or request service online here http://depot.info.apple.com/ipod/
    If it is out of warranty you can google a third party service provider and get it serviced out of warranty. There are two that I know of that provide free diagnostic service. You only pay for shipping and they will tell you what is wrong and what it will cost to fix. They are ifixipodsfast.com and ipodmods.com but there are others also (I just have no experience with them) Good luck and as was stated it should charge from your usb. and just for grins, look at the docking connector on your ipod and see if there is any obstruction that is obvious.

Maybe you are looking for

  • Is there any way to retrieve files from my Original Aperture 2 library after conversion to Aperture 3?

    My original conversion locked up due to damaged file. I repaired Library and process completed,I thought! Now I'm finding folders from the conversion empty. I can go back to the Original Library and use the show contents command to view the files. Th

  • Bpm:message being sent and wait for event

    Hi,gurus: My scenario is about BPM.In the integration process I used a loop and correlation.The scenario worked successfully yesterday,but after I changed some thing,it did not work.The outbound status of the message in sxi_monitor said "message bein

  • Updating button icon issue

    Hi, thanks for stopping by. Working with scriptUI panel and trying to update icon for my button, but something goes wrong with my code, I guess... Can someone write what is the problem here? var mainPanel; function stabpanel(thisObj) {     mainPanel

  • How to resize the stage from the top instead of the bottom?

    Hi  I am trying to resize the stage in Flash CS4 from the top instead of the bottom, as I left too much space at the top of the stage and don't need the stage to be so big.  By default Flash resizes from the bottom. So is there a way of resizing from

  • Flex2 CompilerException: Encountered invalid display object Window :

    Hello, I'm using VC 7.0 with SPS 14 and the new Flex 2 runtime. When I deploy an existing Flex VC 7.0 model with the new runtime I get the following Flex Compiler exception: Flex2Compiler.Compile: FlexCompilerException: Encountered invalid display ob