E7 USB Charging does not work when keyboard is loc...

I have noticed that if the usb cable is connected when the E7 keyboard is locked, the phone does not charge.
Is this a bug or an "undocumented feature"?
Solved!
Go to Solution.

Just tested it on mine it charges without problems, btw I checked it by connecting to a PC in Ovi suite mode. I presume you face same problem using wall charger and PC USB charging. Restore it to factory settings and check(*#7780#), worth giving a shot. If it doesn't help take it to a Nokia care center.
If a reply has solved your problem click Accept as solution button, doing it will help others know the solution. Thanks.

Similar Messages

  • USB Drive does not work when connected to Airport Extreme

    I had an external drive connect directly to my iMac and recently purchased an Airport Extreme. When I plugged it into the USB point on the back of the AX has an odd name and won't allow access. When it was configured directly to my iMac it was named TheVault, now it is TheVault???. When I try to access via Go>Network in finder menu, I get "The operation cannot be completed because the original item for "TheVault??? cannot be found." Another detail if found in the GetInfo it that it shows 0kb available. All things point to it's existence as a drive but it has no access to the data that was clearly there when it was plugged into the back of the desktop. Jack sends.

    TheWack wrote:
    I had an external drive connect directly to my iMac and recently purchased an Airport Extreme. When I plugged it into the USB point on the back of the AX has an odd name and won't allow access.
    Did you use AirPort Utility to enable disk sharing?

  • I am using iPad1. Running v4.3 and when connecting to wifi iPad keyboard does not work. Keyboard works for everything else including typing this question out. Why would it not work when typingin password for wifi connection?

    I am using iPad1. Running v4.3 and when connecting to wifi iPad keyboard does not work. Keyboard works for everything else including typing this question out. Why would it not work when typingin password for wifi connection?

    Kowhai wrote:
    Lots of WIFI needs a username and password to get access. I guess you're lucky and yours is set up unsecured.
    Normal secured WiFi requires only a password to get access. The password is used to encrypt traffic between your device and the WiFi access point. If whatever you are using requires a username as well then it is not simply normal secured WiFi. It might be a subscription WiFi service like GOGO, ATT, etc., or a service with authentication, i.e., college campus, etc. To help you out we need to know what you are using and what connection dialog you are being presented with. You don't have exactly the same problem as the original poster. He is having a problem entering a password into the password dialog that iOS presents when one tries to connect to a normal secured WiFi network. Could you clarify exactly which WiFi service you are using.

  • USB hub does not work!  Help

    I was attempting to install a KVM switch for my G4 and G5 that required me attaching my keyboard and mouse to the usb port on the back of the monitor.
    The USB hub does not work! Monitor cable has no bent pins, and works perfectly for video with all my Mac's, G4's, G5's. The problem is I have had this monitor awhile and never tried these ports so apple won't help.
    Anyone have any suggestions why these ports don't work and if there is a fix?
    Can any one recommend a KVM switch that supports ADC, and USB so I bypass this hub.
    Thanks

    Some USB 2.0 hardware works very well w/USB 3.0 & some don't.  Suggest that you contact the sound card manufacturer & ask them.  Perhaps they can recommend a work-a-round. 
    Another user posted about the same problem some weeks ago regarding a sound card. 

  • External USB HD does not work with HAL:

    External USB HD does not work with HAL:
    From the last 10 days the HAL auto-mount with ntfs-3g file system of my external hard drive  does not woks.
    But the manual mount procedure with the command mount -t ntfs-3g /dev/sdb* /mnt/XYZ works.
    I've followed the instructions in the wiki: http://wiki.archlinux.org/index.php/HAL and the system has worked up to the last kernel or HAL update.
    My fat32 usb-stick works without any problem.
    If I try to open the device with KDE it appears an error popup wit this message:
    TODO: have to rethink extra options
    Error: kio_media_mount_helper
    The log from the kernel.log is
    Nov 6 22:03:16 myhost usb 5-1: new high speed USB device using ehci_hcd and address 4
    Nov 6 22:03:16 myhost usb 5-1: configuration #1 chosen from 1 choice
    Nov 6 22:03:17 myhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    Nov 6 22:03:17 myhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    Nov 6 22:03:17 myhost Initializing USB Mass Storage driver...
    Nov 6 22:03:17 myhost scsi6 : SCSI emulation for USB Mass Storage devices
    Nov 6 22:03:17 myhost usb-storage: device found at 4
    Nov 6 22:03:17 myhost usb-storage: waiting for device to settle before scanning
    Nov 6 22:03:17 myhost usbcore: registered new interface driver usb-storage
    Nov 6 22:03:17 myhost USB Mass Storage support registered.
    Nov 6 22:03:22 myhost scsi 6:0:0:0: Direct-Access WDC WD32 00JB-00KFA0 0811 PQ: 0 ANSI: 0
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
    Nov 6 22:03:22 myhost sdb: sdb1
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Attached SCSI disk
    Nov 6 22:03:22 myhost sd 6:0:0:0: Attached scsi generic sg2 type 0
    Nov 6 22:03:22 myhost usb-storage: device scan complete
    and the error.log is
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
    Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
    Do you have some idea ....
    Bye.

    I have done the following:
    Downloaded the patched hal version.
    used makepkg in /abs/local/trunk/ to create a pkg for pacman
    used sudo pacman -U pkgname to install it.
    used sudo nano /etc/hal/fdi/policy/preferences.fdi to create the fdi file with the following content:
    saved the file and removed my ntfs entryes from fstab and rebooted. and still there is no automount off ntfs partitions.
    have i done something wrong?
    br fjodork
    WARNING: what follows is a guide of what did work for me, I'm still in an early stage of learning linux, so please correct me if anything of what follows is wrong/dangerous/stupid. As I said, this worked for me, it's not pretty, since I was learning each step on the fly and I'm sure there are better ways to do this.
    So fjodork, you seem to have done the the necessary steps, though i couldn't get it to work until i first removed hal without dependencies
    pacman -Rd hal
    it will give you some warning about the dependencies, ignore  it since we are reinstalling hal in a few steps.
    First i tried to follow Raymano's link, obviously it showed me nothing in the browser so I thought it might be a broken link.
    So I downloaded the source tarball from here http://hal.freedesktop.org/releases/hal-0.5.10.tar.gz
    unpacked it changed the /tools/hal-storage-mount.c as per Milfadoodle's instructions.
    at first I tried to compile directly from source, the process would finish without a glitch though after reboot nothing changed, as if hal weren't
    installed, i guess there were issues with paths. anyway read on
    Then repacked the source in tarball, copied it to /var/abs/extra/system/hal and modified the PKGBUILD as follows
    makedepends=('pkgconfig' 'gperf')
    options=('!libtool')
    install=hal.install
    source=(${pkgname}-${pkgver}.tar.gz #removed url so makepkg looks in the current directory for the tarball
        hal
        hal-policy.patch
        cryptsetup_location.patch
        hal-0.5.9-hide-diagnostic.patch
        ntfs3g-valid-options.patch)
    md5sums=('6641c30a27c00485c6accac5110ff911' # replace with md5sum of your package's sourceball (run md5sum filename)
             '882f67668cb14a0a9e4a27ef22278027'
             '5ba8b610aa9763a5f42b9f7cbd7a86ad'
    then makepkg (i had to add --asroot, don't ask why
    and finally pacman -U hal-0.5.10-1-i686.pkg
    another reboot and everything worked without a glitch!:D (yeah i know i still haven't got rid of the reboot mentality )
    I have also put the policy files as per the wiki instructions.
    PS: I know this is a dirty way to getting things done but as i said, I'm just starting
    If anyone could comment/correct/explain this post I'd be more than happy, the automount issue was bothering me for about a month now (you'll say why do I need ntfs in the first place? well, I only recently switched for Linux as my primary OS, these are some relics of the M$ era

  • USB ports does not work

    Hi I have problems with not working USB ports. It used to work. I downloaded actual drivers at msi.com for my gaming notebook GX 60 Destroyer and now my USB ports does not work. What should I do?

    What driver have you updated?
    Try to do an EC firmware reset by removing the battery and the AC adapter then put the battery back with AC adapter attached.
    Same questions like Pegasus asked, does all ports not working? which one exactly? What OS are you using?
    Have you done any changes to the system? (for example: self-install OS or changing OS)

  • HT201413 Device does not work when I connect it to your computer to the iTunes program update requests and then gives me an error No. 21

    Device does not work when I connect it to your computer to the iTunes program update requests and then gives me an error No. 21

    Device does not work when I connect it to my computer to the iTunes program update requests and then gives me an error No. 21

  • TS3276 My o2 email account does not work when sending from my MAC it will accept incoming mail but not send it gives me a message that  o2 account (offline) my mac I have no problem with my iPhone  or mac laptop. any suggestions please.

    My o2 email account does not work when sending from my MAC it will accept incoming mail but not send it gives me a message that  o2 account (offline) my mac I have no problem with my iPhone  or mac laptop. any suggestions please.

    Sorry for the delay...
    I did what you've told me, new account and manually copied my files from Time Machine. I had lots of permissions problems, but at the end, almost everything is in order... It seems it had to be with some of the Apple Preferences, but I can't be sure, as most of them were dumped to the trash can.
    I still don't have my Mail Rules back, unfortunately, although I did goggled some. It is a pity, as I had around 30 or 40 of them, getting my mail in order to each of its mailboxes, but it is a small price as the rest doesn't show the before syntoms.
    Thanks for the help, anyway!!

  • My iPad 2 charger is not working when plugged to a wall..but when plugged to a computer...it says unknown device...what's happening and how do I fix this problem?!

    My iPad 2 charger is not working when plugged to a wall..but when plugged to a computer...it says unknown device...what's happening and how do I fix this problem?!

    Have you recharge your iPod for at least 2 hours, preferably till the Full charge Battery symbol comes ON.?
    See this Apple support Article
    http://www.apple.com/support/ipod/five_rs/classic/
    You did not by chance bought the Hello Kitty special edition?
    Have nice day!

  • Reply to all using ItemReply does not work when specifying messageid

    Hello everyone,
    I am trying to use the ItemReply token to perform a "Reply to All"
    action on a mail item with a known message identifier and include the
    original message text in the response. According to the documentation,
    the call should be:
    ItemReply(7;1;"message-id")
    Still, when I execute this token, apparently only a normal reply action
    is performed because only the original sender is listed as recipient.
    (The message text is properly included)
    However, when I manually select the message in the GroupWise client
    first and then execute the same call without specifying the message id,
    all recipients of the original mail are listed in "To:" as expected:
    ItemReply(7;1)
    Could it be that the "ReplyTo" parameter is ignored or does not work
    when a message id is specified as parameter? (Setting "IncludeText" to 0
    does not change anything)
    Thanks in advance and best regards,
    Peter Hofer

    Worth bumping this message. I find the exact same behaviour as mentioned 5 years ago. Using both GW8 and GW2012.
    According documentation, when MessageId is not specified it defaults to the command ItemReplyOpenItem(). I assume that the reason "Reply To all" works without a MessageID is because of that. Someone needs to give a look to ItemReply().

  • How do I set up a mail group on mac mail?  All the advise on line seems to refer to 'address book' and I only have 'contacts'.  The guidance does not work when using 'contacts' - can anyone help me?

    How do I set up a mail group on mac mail?  All the advise on line seems to refer to 'address book' and I only have 'contacts'.  The guidance does not work when using 'contacts' - can anyone help me?

    Create a group and send mail
    http://www.dummies.com/how-to/content/how-to-create-a-basic-contact-group-in-mac -os-x-li.html
    http://www.macworld.com/article/1165582/how_to_email_groups_with_mail.html
    Best.

  • My App Store does not work when trying to update applications

    My Apo store does not work when I try to update applications that need to be updated

    There are a number of other threads from people reporting a problem with a blank Updates tab in the App Store app - it looks like there is a problem at Apple's end which they need to fix.
    Some posts are suggesting that you if you go into the Purchased tab in the App Store app you might be able to update the apps from there, though you will need to scroll through the list to find those with updates and individually update them.

  • Siri does not work when used for calling a contact function

    Siri does not work when used for calling a contact function

    Very strange, try to turn off/on your iPhone. Or make a reset (home+power button)...
    If it continues try to restore it.

  • The remote does not work, when i turn the tv on I see the apple tv and the itune icon on the screen

    the remote on apple tv does not work,when i turn on the tv Isee the appletv and the itune icon on the screen.

    Did you do a software update?
    AppleTV is unable to start properly.  You need to connect to a computer running iTunes as detailed here:
    Apple TV (2nd and 3rd generation): Restoring your Apple TV

  • Dbx does not work when debugging g++ exes.

    Hi,
    We are just getting started building our application on redhat el5 with sunstudio 12.
    We are compiling and linking our app with gcc 4.1 as we need to be able to link against some 3rd party libraries build on rhel4 that we do not have source for.
    We now can compile and link fine but dbx does not work when it is fed the executable.
    We get the error
    dbx: warning: Bad transition in runtime linker interface. CONSISTENT->CONSISTENT[
    and dbx freezes.
    Note : This is built with -m32 on a 64bit kernel. Also we have not yet rebuilt all the opensource libs used on gcc 4.1 as we have a large number of them.
    Any ideas ?
    The complete output of running dbx :
    Output from dbx :
    debug /ps_rels/Dev/linux_rhel5/exe/sx
    Reading sx
    Reading ld-linux.so.2
    Reading libz.so.1
    Reading libxerces-c.so.27
    Reading libxalan-c.so.110
    Reading libxalanMsg.so.110
    Reading libsde.so
    Reading libsg.so
    Reading libpe.so
    Reading libsqlite.so.0
    Reading libsqlite3.so.0
    Reading libgeos.so.2
    Reading libpng12.so.0
    Reading libX11.so.6
    Reading libXm.so.4
    Reading libXt.so.6
    Reading libXi.so.6
    Reading libXext.so.6
    Reading libXrender.so.1
    Reading libfreetype.so.6
    Reading libexpat.so.0
    Reading libfontconfig.so.1
    Reading libcairo.so.2
    Reading libglib-2.0.so.0
    Reading libgmodule-2.0.so.0
    Reading libgobject-2.0.so.0
    Reading libgthread-2.0.so.0
    Reading libpango-1.0.so.0
    Reading libpangocairo-1.0.so.0
    Reading libpangoft2-1.0.so.0
    Reading libatk-1.0.so.0
    Reading libgtk-x11-2.0.so.0
    Reading libgdk-x11-2.0.so.0
    Reading libgdk_pixbuf-2.0.so.0
    Reading libtiff.so.3
    Reading librt.so.1
    Reading libwx_gtk2_xrc-2.8.so.0
    Reading libwx_gtk2_qa-2.8.so.0
    Reading libwx_gtk2_html-2.8.so.0
    Reading libwx_gtk2_adv-2.8.so.0
    Reading libwx_gtk2_core-2.8.so.0
    Reading libwx_base_xml-2.8.so.0
    Reading libwx_base_net-2.8.so.0
    Reading libwx_base-2.8.so.0
    Reading libboost_thread-gcc-mt-1_33_1.so.1.33.1
    Reading libboost_filesystem-gcc-mt-1_33_1.so.1.33.1
    Reading libncurses.so.5
    Reading libnsl.so.1
    Reading libdl.so.2
    Reading libACE.so.5.5.1
    Reading libpthread.so.0
    Reading libpam.so.0
    Reading libm.so.6
    Reading libc.so.6
    Reading libstdc++.so.6
    Reading libgcc_s.so.1
    Reading libicuuc.so.34
    Reading libicui18n.so.34
    Reading libstdc++.so.5
    Reading libXau.so.6
    Reading libXdmcp.so.6
    Reading libXmu.so.6
    Reading libXp.so.6
    Reading libXft.so.2
    Reading libjpeg.so.62
    Reading libSM.so.6
    Reading libICE.so.6
    Reading libexpat.so.1
    Reading libXfixes.so.3
    Reading libXrandr.so.2
    Reading libXinerama.so.1
    Reading libXcursor.so.1
    Reading libXxf86vm.so.1
    Reading libaudit.so.0
    Reading libicudata.so.34
    Reading libnss_files.so.2
    Reading libnss_dns.so.2
    Reading libresolv.so.2
    dbx: warning: Bad transition in runtime linker interface. CONSISTENT->CONSISTENT
    Reading libnss_ldap.so.2
    Reading libcom_err.so.2

    Well, this message is just a warning and should not prevent dbx from working. What exactly happens to dbx? Does it hang? Does it crash? Or it doesn't allow to run the app?
    A side note: this message says that runtime linker debugging interface reported "consistent" event w/o any "add" or "delete" events, which is at least redundant and may indicate a bug. It is possible though that the bug is in dbx as well as in ld-linux.so, but its impossible to tell without live test case.

Maybe you are looking for