E71-1 - No inbox/notification in active standby
In the past days I have tried to configure any kind of information about my primary email account for the active standby/home screen. The email account works fine (imap-idle account), receiving emails works fine, but other than the @-symbol in the top-right corner (when new emails are available) no information about the inbox or any indication about new emails are displayed on the home screen.
In the mode-config I selected the email account to be displayed on the home screen, and no matter what option I choose in the email notification 1 details (headers only, headers with popup, headers with unread etc.) nothing at all is shown. I have seen screen shots where at least a bubble notification is shown (for new emails) and also at least a link with the account name. The way it is now I have a really hard time keeping track of my (new) emails, because I really have to open my inbox every time to be sure.
I have tried every imaginable configuration detail, the manual is no help at all, and I didn't find any information in any forums about this problem. Is this a software bug? Has anybody experienced this? Is there a solution?
I've been experiencing the same issue where that active standby plugin wouldnt show a notification. But I *THINK* I have it figured out from the clues in this discussion. This post is to benefit any other people googling for the solution. To my knowledge, this method will enable you to have the single line email notication on your Active Standby aka homescreen (where your calendar and meetings show up) in the format of Gmail (6). I believe the catch is you need to have less than 999 emails in your inbox. As a workaround you need to archive all extra emails in your Gmail inbox. A disclaimer: I am not 100% on this, so I will give you as much detail to replicate my scenario where it works, so adjust it for your own situation
I went through various deletes of my Gmail account in the Email settings area of the NATIVE messaging app (where text messages are).
If you look at Messaging --> Options --> Settings --> Other
There is a setting called "Number of saved msgs." I figured out the maximum of this to be 999. In my opinion this setting is talked about saved SENT messages (the setting above it is called "Save sent messages" Yes/No). Set this number to 999.
I assumed this 999 number of messages to be the limit for all emails out of a hunch. I went into my Gmail account on the web and pretty much archived a lot of emails except the recent ones. Archiving your emails does not delete them, but rather stores them outside of the inbox and are still searchable within Gmail. I made sure the number of emails in my inbox were under 900.
Next, I followed the steps we all know to put in a Gmail account via IMAP via the setup email wizard and some minor tweaking in the settings dialogs (Messaging --> Options --> Settings --> Email --> Gmail --> Connections Settings --> Both Incoming e-mail and Outgoing e-mail sections) using the guide: Symbian S60 - Gmail Help
It might also be worth it to set your "Access point in use" for both incoming and outgoing servers.
Under
Messaging --> Options --> Settings --> Email --> Gmail --> User Settings --> New e-mail alerts should be ON
Under
Messaging --> Options --> Settings --> Email --> Gmail --> Retrieval Settings --> there are no necessary changes (the next section will override settings related to retrieval amount and cause ALL emails to be retrieved.). Note that putting folder subscriptions may put you over the 999 limit. I don't know if the 999 limit applies to each folder or to ALL emails as a whole. If you do put folder subscriptions, the next section setting will automatically also override the # of emails from folders retrieved to be ALL as well. Experiment at your own risk.
Under
Messaging --> Options --> Settings --> Email --> Gmail --> Automatic Retrieval:
Email notifications -- Disabled (you can only have one or the other and email retrieval is more important than this unknown and ill defined setting)
Email retrieval -- Enabled or "only in home network" (more options will appear now regarding scheduling. Pick your frequency according to how long you want your battery to last and how important your emails are). If you choose "only in home network" I am inclined to believe that it will only use the access point you described earlier in "Connection Settings"
Out of this menu,
Under
Messaging --> Options --> Settings --> Email
Make sure your default mailbox is Gmail
If you go into Modes (Modes--> Home screen apps --> Enabled apps) at this point and try to put the "Email 1 notification" as active, and go into "Email 1 notification's " settings, and try to set your mailbox to Gmail, it will tell you to connect first. So lets do that and hope it works
So go to Messaging --> Gmail --> Options --> Connect and watch it retrieve headers of your emails from Gmail. Make sure that theres 1 or 2 *NEW* emails before downloading for testing out the Active Standby plugin's temperment.
Go into Modes while it is retrieving the headers of your emails
Modes --> Home screen apps --> Enabled Apps --> and select "Email 1 notification"
Go back into
Modes --> Home screen apps --> Go into the new "Email 1 Notification" setting there
Mailbox: Gmail
Preview: You have a choice of three
Header only -- shows your mailbox's name and # of unread mails on homescreen -- eg: Gmail (3)
Header and popup -- show the header described above in 1 line, plus when you hover over it, a preview of your emails in a bubble that includes Sender, Subject, and Date. To me, this is the most useful
Header and unread -- Shows the header described above in 1 line, and in a 2nd line shows the most recent unread email's Sender, subject, and date
Assuming you've put a audio tone for email alerts in Profiles --> Whichever profile --> Customize --> Email alert tone
Then once you head back to your home screen and once the email retrieval finishes, you should hear a audio sound, and see Gmail (3).
Good luck
Similar Messages
-
E51: How set active standby inbox to Gmail/All Mai...
I have a few problems setting up the active standby inbox to point to my gmail account's "All mail" folder.
First of all, it's not possible to unsubscribe to the Gmail inbox under Folder Subscriptions. This is a minor problem though as I don't use the Gmail inbox, but route all my emails to All Mail through a forwarding system.
So I'd like my active standby inbox to reflect the All Mail folder.
Selecting "gmail" under Email Settings/Default mailbox allows me to choose between "Inbox" and "[Google Mail]".
But, unlike in Email Settings/gmail/Retrieval Settings/Folder Subscriptions, I cannot go one step further and choose "All Mail".
This means that while my active standby inbox will show "gmail [Google Mail]" it won't show the new message(s).
Anyway around this? Well, apart from filtering all my emails to my inbox.hello Graham
I guess you have disabled the active standby in-box plugin. Check it under "menu>tools>settings>phone>standby mode>active standby plug-ins", maybe you disabled it. Then under the same menu (standby mode) should be a new entry "active standby mailbox" where you have to select "inbox" for it to display those 2 latest sms in the active standby screen.
(the menu options may not be exactly as I mentioned, as I'm using portuguese UI)
Hope it helps
CheersMessage Edited by skanker on 08-Dec-200701:49 AM -
Active/standby pair + Oracle db parameter FAILTHRESHOLD
Assume we have 3 databases
TT_A - timesten Active
TT_S - timesten Standby
O - oracle db.
SETURN MODE twosafe
Storage atributes
RETURN SERVICES OFF WHEN REPLICATION STOPPED;
FAILTHRESHOLD set to 10 value.
Two timesten databases are in consistent state.
Aplication update TT_A.
TT_S replication data to ORACLE.
Assume we stop replication.
So application can run on TT_A.
After 10 log switch TT_S will be marked as failed.
All logs waiting for TT_S will be delete.
So how oracle receiv the data ?In active standby pair replication, cache operations are tightly coupled with replication. In normal operation of AWT cache group within an A/S pair, updates occur at the active which replicates them to the standby and then the standby pushes them to Oracle. The active and standby continually exchange housekeeping information about what transactions have been committed at the standby and which have been committed, via AWT, at Oracle. The active and the standby will only purge transaction logs for transactions that they know are safely stored in all 3 places. If the standby fails then, as long as you tell the active that it has failed (via a call to ttRepStateSave()), the active will take over the AWT push from the last transaction that it knows was safely committed in Oracle. No data will be lost.
If you are using oracle Clusterware to manage your A/S pair then you don't need to do anything as Clusterware will perform the necessary notification to the active that the standby has failed.
Chris -
E70 Active Standby limitations
In some early pictures active standby on the E70 had six shortcuts, the production version only has five which is very limited. Even my old 6230 had a shortcut menu that you could edit and pick as much options as you like. I miss this and wonder why the shortcut bar on the E70 (and maybe on other e-series) can not be used for much more buttons and made scrollable. I find this a serious problem.
Owner Nokia 520 (experiment: serious problems connecting pop accounts).
History: Siemens S4, Sony Z1, Ericsson SH888, Siemens s40, Nokia 6230, Nokia E70. Nokia E71-1, E72-1, HTC Wildfire (good stuff), HTC One V (also nice).
(And sometimes I still miss my Psion Revo! ;-)@trotty
I already have too little option in the nenu. Nice too know there's another one that is very handy
And about the screen resolution:
I have some serious doubts about this.
The fonts are almost too small to read.
It's certainly not easy anymore.
Might also be something that has to do with my own firmware which dates back to 1954, but still, I think Nokia has crossed a border here that makes it more user unfriendly.
Owner Nokia 520 (experiment: serious problems connecting pop accounts).
History: Siemens S4, Sony Z1, Ericsson SH888, Siemens s40, Nokia 6230, Nokia E70. Nokia E71-1, E72-1, HTC Wildfire (good stuff), HTC One V (also nice).
(And sometimes I still miss my Psion Revo! ;-) -
Facebook inbox notifications are no longer showing with new OS 4.5
Hi all:
I have a Curve 8310 with ATT. Just downloaded the new os 4.5 and got the facebook reinstalled so that I can see the icon. However, now when I get messages through my facebook inbox, notifications no longer appear on the home screen. On fact, the new emails are not showing up at all. Any thoughts?Hello and Welcme to the Frums!
Go to your facebook on your pc and check your notifications. When I downloaded the 4.5 I had to reset all my notifications. Somehow it reset them! Let us know if that is it!
Have a blessed day
Nurse-Berry
Follow NurseBerry08 on Twitter -
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
This topic has been beat to death, but I did not see a real answer. Here is configuration:
1) 2 x ASA 5520, running 8.2
2) Both ASA are in same outside and inside interface broadcast domains – common Ethernet on interfaces
3) Both ASA are running single context but are active/standby failovers of each other. There are no more ASA’s in the equation. Just these 2. NOTE: this is not a Active/Active failover configuration. This is simply a 1-context active/standby configuration.
4) I want to share VPN load among two devices and retain active/standby failover functionality. Can I use VPN load balancing feature?
This sounds trivial, but I cannot find a clear answer (without testing this); and many people are confusing the issue. Here are some examples of confusion. These do not apply to my scenario.
Active/Active failover is understood to mean only two ASA running multi-contexts. Context 1 is active on ASA1 Context 2 is active on ASA2. They are sharing failover information. Active/Active does not mean two independently configured ASA devices, which do not share failover communication, but do VPN load balancing. It is clear that this latter scenario will work and that both ASA are active, but they are not in the Active/Active configuration definition. Some people are calling VPN load balancing on two unique ASA’s “active/active”, but it is not
The other confusing thing I have seen is that VPN config guide for VPN load balancing mentions configuring separate IP address pools on the VPN devices, so that clients on ASA1 do not have IP address overlap with clients on ASA2. When you configure ip address pool on active ASA1, this gets replicated to standby ASA2. In other words, you cannot have two unique IP address pools on a ASA Active/Standby cluster. I guess I could draw addresses from external DHCP server, and then do some kind of routing. Perhaps this will work?
In any case, any experts out there that can answer question? TIA!Wow, some good info posted here (both questions and some answers). I'm in a similar situation with a couple of vpn load-balanced pairs... my goal was to get active-standby failover up and running in each pair- then I ran into this thread and saw the first post about the unique IP addr pools (and obviously we can't have unique pools in an active-standby failover rig where the complete config is replicated). So it would seem that these two features are indeed mutually exclusive. Real nice initial post to call this out.
Now I'm wondering if the ASA could actually handle a single addr pool in an active-standby fo rig- *if* the code supported the exchange of addr pool status between the fo members (so they each would know what addrs have been farmed out from this single pool)? Can I get some feedback from folks on this? If this is viable, then I suppose we could submit a feature request to Cisco... not that this would necessarily be supported anytime soon, but it might be worth a try. And I'm also assuming we might need a vip on the inside int as well (not just on the outside), to properly flip the traffic on both sides if the failover occurs (note we're not currently doing this).
Finally, if a member fails in a std load-balanced vpn pair (w/o fo disabled), the remaining member must take over traffic hitting the vip addr (full time)... can someone tell me how this works? And when this pair is working normally (with both members up), do the two systems coordinate who owns the vip at any time to load-balance the traffic? Is this basically how their load-balancing scheme works?
Anyway, pretty cool thread... would really appreciate it if folks could give some feedback on some of the above.
Thanks much,
Mike -
FWSM Active/Standby in VSS mode
hello,
i do have two 6500 in VSS mode , and one FWSM module on each 6500, i want to configure these modules as Active/Standby, how do i start , should i follow this (not in VSS mode):
http://www.cisco.com/en/US/docs/security/fwsm/fwsm32/configuration/guide/fail_f.html
or are there other things should i do to make it work,
thanksup!
-
N81 How to Show calender at active standby
Hi, i just bought a N81, but i just cant seem to get the phone to show the calender details for the day at the active standby mode(the main page). I can do it previously on my 6280.
Anyone can help?12-Jun-2008 11:42 AM
psychomania wrote:
Pass, it reads to me like they want to change the active standby shortcuts and can't find which application to use in the phone.
It reads like that to me too.
Grayburn @ www.nokiausers.net & www.dailymobile.se....come say Hello!!!
If you appreciate ANY help from a member,then show it by clicking on the Blue Star button, cheers -
11.2.0.3 RAC ASM Pri with Normal FileSys Active Standby Post Failover
The architecture consist of two node rac asm primary and one normal filesystem active standby all on Oracle 11gR2 11.2.0.3. With basic Broker Configuration.
Performed a managed broker switchover and not the Normal Filesystem has the primary role and the standby consist of the two node asm rac. I want to switchback, i.e., Former Primary -> Primary Role and Former Standby -> Standby Role.
However my broker contains the following:
DGMGRL> show configuration verbose;
Configuration - DG_PRI_CFG
Protection Mode: MaxPerformance
Databases:
STANDBY - Primary database
Warning: ORA-16829: fast-start failover configuration is lagging
KEMETRAC - (*) Physical standby database
Error: ORA-16810: multiple errors or warnings detected for the database
(*) Fast-Start Failover target
Properties:
FastStartFailoverThreshold = '95'
OperationTimeout = '30'
FastStartFailoverLagLimit = '95'
CommunicationTimeout = '180'
FastStartFailoverAutoReinstate = 'TRUE'
FastStartFailoverPmyShutdown = 'TRUE'
BystandersFollowRoleChange = 'ALL'
Fast-Start Failover: ENABLED
Threshold: 95 seconds
Target: KEMETRAC
Observer: emcc.respecti.com
Lag Limit: 95 seconds
Shutdown Primary: TRUE
Auto-reinstate: TRUE
Configuration Status:
ERROR
I've found a recommendation to increase the value of FastStartFailoverThreshold='90';
Though I continue to encounter the above configuration error.
Recommendations are appreciated!
Edited by: 783527 on Mar 12, 2012 7:41 PM03/13/2012 13:13:22
Data Guard Broker Status Summary:
Type Name Severity Status
Configuration DG_PRI_CFG Warning ORA-16607
Primary Database STANDBY Warning ORA-16829
Physical Standby Database KEMETRAC Error ORA-16810
03/13/2012 13:14:22
Data Guard Broker Status Summary:
Type Name Severity Status
Configuration DG_PRI_CFG Warning ORA-16607
Primary Database STANDBY Warning ORA-16829
Physical Standby Database KEMETRAC Error ORA-16810
03/13/2012 13:15:22
Data Guard Broker Status Summary:
Type Name Severity Status
Configuration DG_PRI_CFG Warning ORA-16607
Primary Database STANDBY Warning ORA-16829
Physical Standby Database KEMETRAC Error ORA-16810
03/13/2012 13:16:22
Data Guard Broker Status Summary:
Type Name Severity Status
Configuration DG_PRI_CFG Warning ORA-16607
Primary Database STANDBY Warning ORA-16829
Physical Standby Database KEMETRAC Error ORA-16810
03/13/2012 13:17:22
Data Guard Broker Status Summary:
Type Name Severity Status
Configuration DG_PRI_CFG Warning ORA-16607
Primary Database STANDBY Warning ORA-16829
Physical Standby Database KEMETRAC Error ORA-16810
03/13/2012 13:18:22 -
Plug-ins for Active Standby on Nokia 6110 Navigato...
Is there any way to get other active standby screen plugins on the Nokia 6110 Navigator? I have callender but I'd also like Bluetooth, messages etc. I have a Voda UK branded one.
Good paulrouy - what a team - can you play sweeper
Today Me Tomorrow You -
ASA 8.2 8.4 9.1 possible with no downtime as we run active/standby?
Hello,
We have 2 x ASA 5520s (with 2GB mem) in active/standby mode, they also include the IPS modules.
The current firmware is 8.2 and I was wondering if it is possible to upgrade these firewalls with no downtimes? In the past I have upgraded the standby ASA, rebooted it and then made it the active ASA then upgraded the new standby ASA.
I have have quite a lot of NAT Exempts (No-NATs?) and a few static NATs, how did you approach this during your upgrades?
I guess I can roll back as the 8.2 firmware will still be on the flash and I will have the config?
ThanksYeah it's supported:
Release Notes for the Cisco ASA Series, 9.1(x)
http://www.cisco.com/en/US/docs/security/asa/asa91/release/notes/asarn91.html#wp732442
This document has the information that you need; it talks about the requirements and zero downtime procedure.
But you need to take a lot of considerations that you can reference in the document:
https://supportforums.cisco.com/docs/DOC-12690
If you don't mind me asking why are you upgrading?
Because of a fix or feature? -
ASA 5520: Configuring Active/Standby High Availability
Hi,
I am new to Cisco firewalls. We are moving from a different vendor to Cisco ASA 5520s.
I have two ASA 5520s running ASA 8.2(5). I am managing them with ASDM 6.4(5).
I am trying to setup Active/Standby using the High Availability Wizard. I have interfaces on each device setup with just an IP address and subnet mask. Primary is 10.1.70.1/24 and secondary is 10.1.70.2/24. The interfaces are connected to a switch and these interfaces are the only nodes on this switch. When I run the Wizard on the primary, configure for Active/Standby, enter the peer IP of 10.1.70.2 and I get an error message saying that the peer test failed, followed by an error saying ASDM is temporarily unable to connect to the firewall.
I tried this using a crossover cable to connect the interfaces directly with the same result.
Any ideas?
Thanks.
DanThe command Varun is right.
Since you want to know a little bit more about this stuff, here goes a bit. Every interface will have a secondary IP and a Primary IP where the Active/Standby pair will exchange hello packes. If the hellos are not heard from mate, the the unit is delcare failed.
In case the primary is the one that gets an interface down, it will failover to the other unit, if it is the standby that has the problem, the active unit will declare the other Unit "standby failed). You will know that everything is alright when you do a show failover and the standby pair shows "Standby Ready".
For configuring it, just put a secondary IP on every interface to be monitored (If by any chance you dont have an available secondary IP for one of the interfaces you can avoid monitoring the given interface using the command no "monitor-interface nameif" where the nameif is the name of the interface without the secondary IP.
Then put the commands for failover and stateful link, the stateful link will copy the connections table (among other things) to avoid downtime while passing from One unit to another, This link should have at least the same speed as the regular data interfaces.
You can configure the failover link and the stateful link in just one interface, by just using the same name for the link, remember that this link will have a totally sepparate subnet from the ones already used in firewall.
This is the configuration
failover lan unit primary
failover lan interface failover gig0/3
failover link failover gig0/3
failover interface ip failover 10.1.0.1 255.255.255.0 standby 10.1.0.2
failover lan unit secondary
failover lan interface failover gig0/3
failover link failover gig0/3
failover interface ip failover 10.1.0.1 255.255.255.0 standby 10.1.0.2
Make sure that you can ping each other secondary/primary IP and then put the command
failover first on the primary and then on the secondary.
That would fine.
Let me know if you have further doubts.
Link for reference
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008080dfa7.shtml
Mike -
About stateful active/standby failover
Hello guys.
I have two ASA's, same model and hardware. Asa have configured stateful active/standby failover by someone, few years ago. It was working normally until recently and no one have changed this configuration. Then Secondary unit is failed. Ping between 2 interfaces is ok. Please help me to resolve this problem.
on Primary site
interface Management0/0
description STATE Failover Interface
management-only
interface GigabitEthernet1/1
description LAN Failover Interface
failover
failover lan unit primary
failover lan interface failover GigabitEthernet1/1
failover link state Management0/0
failover interface ip failover 172.16.1.1 255.255.255.0 standby 172.16.1.2
failover interface ip state 172.16.0.1 255.255.255.0 standby 172.16.0.2
on Secondary site
interface Management0/0
description STATE Failover Interface
management-only
interface GigabitEthernet1/1
description LAN Failover Interface
output of show failover on PRIMARY
show run failover
failover
failover lan unit primary
failover lan interface failover GigabitEthernet1/1
failover link state Management0/0
failover interface ip failover 172.16.1.1 255.255.255.0 standby 172.16.1.2
failover interface ip state 172.16.0.1 255.255.255.0 standby 172.16.0.2
F1# show failover
Failover On
Failover unit Primary
Failover LAN Interface: failover GigabitEthernet1/1 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 5 of 256 maximum
Version: Ours 8.2(2), Mate 8.2(2)
Last Failover at: 08:03:11 ULAST Jan 1 2003
This host: Primary - Active
Active time: 5755203 (sec)
slot 0: ASA5550 hw/sw rev (2.0/8.2(2)) status (Up Sys)
Interface Backup2 (10.2.5.1): Normal (Waiting)
Interface Internet (202.131.225.90): No Link (Waiting)
Interface Backup1 (10.3.5.1): Normal (Waiting)
Interface Server (192.168.227.1): Normal (Waiting)
Interface Bank (10.20.1.1): Normal (Waiting)
slot 1: ASA-SSM-4GE-INC hw/sw rev (1.0/1.0(0)10) status (Up)
Other host: Secondary - Failed
Active time: 0 (sec)
slot 0: ASA5550 hw/sw rev (2.0/8.2(2)) status (Up Sys)
Interface Backup2 (0.0.0.0): No Link (Waiting)
Interface Internet (0.0.0.0): No Link (Waiting)
Interface Backup1 (0.0.0.0): Normal (Waiting)
Interface Server (0.0.0.0): Normal (Waiting)
Interface Bank (0.0.0.0): Normal (Waiting)
slot 1: ASA-SSM-4GE-INC hw/sw rev (1.0/1.0(0)10) status (Up)
Stateful Failover Logical Update Statistics
Link : state Management0/0 (up)
Stateful Obj xmit xerr rcv rerr
General 76184539 0 767513 6
sys cmd 767328 0 767326 1
up time 0 0 0 0
RPC services 0 0 0 0
TCP conn 25878669 0 11 5
UDP conn 40545710 0 40 0
ARP tbl 8987688 0 136 0
Xlate_Timeout 0 0 0 0
IPv6 ND tbl 0 0 0 0
VPN IKE upd 1140 0 0 0
VPN IPSEC upd 4004 0 0 0
VPN CTCP upd 0 0 0 0
VPN SDI upd 0 0 0 0
VPN DHCP upd 0 0 0 0
SIP Session 0 0 0 0
Logical Update Queue Information
Cur Max Total
Recv Q: 0 7 6522961
Xmit Q: 0 34 106685671
output of show failover on SECONDARY
F1# show failover
Failover On
Failover unit Secondary
Failover LAN Interface: failover GigabitEthernet1/1 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 5 of 256 maximum
Version: Ours 8.2(2), Mate 8.2(2)
Last Failover at: 03:36:23 ULAST Dec 15 2013
This host: Secondary - Failed
Active time: 0 (sec)
slot 0: ASA5550 hw/sw rev (2.0/8.2(2)) status (Up Sys)
Interface Backup2 (0.0.0.0): No Link (Waiting)
Interface Internet (0.0.0.0): No Link (Waiting)
Interface Backup1 (0.0.0.0): Normal (Waiting)
Interface Server (0.0.0.0): Normal (Waiting)
Interface Bank (0.0.0.0): Normal (Waiting)
slot 1: ASA-SSM-4GE-INC hw/sw rev (1.0/1.0(0)10) status (Up)
Other host: Primary - Active
Active time: 5743217 (sec)
slot 0: ASA5550 hw/sw rev (2.0/8.2(2)) status (Up Sys)
Interface Backup2 (10.2.5.1): Normal (Waiting)
Interface Internet (202.131.225.90): No Link (Waiting)
Interface Backup1 (10.3.5.1): Normal (Waiting)
Interface Server (192.168.227.1): Normal (Waiting)
Interface Bank (10.20.1.1): Normal (Waiting)
slot 1: ASA-SSM-4GE-INC hw/sw rev (1.0/1.0(0)10) status (Up)
Stateful Failover Logical Update Statistics
Link : state Management0/0 (up)
Stateful Obj xmit xerr rcv rerr
General 765518 0 35843181 874
sys cmd 765518 0 765516 0
up time 0 0 0 0
RPC services 0 0 0 0
TCP conn 0 0 12671303 80
UDP conn 0 0 13432853 133
ARP tbl 0 0 8968384 661
Xlate_Timeout 0 0 0 0
IPv6 ND tbl 0 0 0 0
VPN IKE upd 0 0 1137 0
VPN IPSEC upd 0 0 3988 0
VPN CTCP upd 0 0 0 0
VPN SDI upd 0 0 0 0
VPN DHCP upd 0 0 0 0
SIP Session 0 0 0 0
Logical Update Queue Information
Cur Max Total
Recv Q: 0 9 72011189
Xmit Q: 0 1 765518- ping is ok between 172.16.1.1 and 172.16.1.2, 172.16.0.1 and 172.16.0.2
- ASA that shows as failed the ASA that didn't use to be the primary , it used to be secondary.
- Yes, i logged via console on both ASAs and checked status of the ASAs. Primary is active and Secondary is failed.
- I have changed cable. Primary ASA indicates below as soon as cable changed.
Beginning configuration replication: Sending to mate.
End Configuration Replication to mate
Then output of SHOW FAILOVER on PRIMARY ASA :
F1# show failover
Failover On
Failover unit Primary
Failover LAN Interface: failover GigabitEthernet1/1 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 5 of 256 maximum
Version: Ours 8.2(2), Mate 8.2(2)
Last Failover at: 08:03:11 ULAST Jan 1 2003
This host: Primary - Active
Active time: 5812656 (sec)
slot 0: ASA5550 hw/sw rev (2.0/8.2(2)) status (Up Sys)
Interface Backup2 (10.2.5.1): Normal (Waiting)
Interface Internet (202.131.225.90): No Link (Waiting)
Interface Backup1 (10.3.5.1): Normal (Waiting)
Interface Server (192.168.227.1): Normal (Waiting)
Interface Bank (10.20.1.1): Normal (Waiting)
slot 1: ASA-SSM-4GE-INC hw/sw rev (1.0/1.0(0)10) status (Up)
Other host: Secondary - Standby Ready
Active time: 9 (sec)
slot 0: ASA5550 hw/sw rev (2.0/8.2(2)) status (Up Sys)
Interface Backup2 (0.0.0.0): No Link (Waiting)
Interface Internet (0.0.0.0): No Link (Waiting)
Interface Backup1 (0.0.0.0): Normal (Waiting)
Interface Server (0.0.0.0): Normal (Waiting)
Interface Bank (0.0.0.0): Normal (Waiting)
slot 1: ASA-SSM-4GE-INC hw/sw rev (1.0/1.0(0)10) status (Up)
Stateful Failover Logical Update Statistics
Link : state Management0/0 (up)
Stateful Obj xmit xerr rcv rerr
General 76940782 0 775168 6
sys cmd 774983 0 774981 1
up time 0 0 0 0
RPC services 0 0 0 0
TCP conn 26125140 0 11 5
UDP conn 40971274 0 40 0
ARP tbl 9064174 0 136 0
Xlate_Timeout 0 0 0 0
IPv6 ND tbl 0 0 0 0
VPN IKE upd 1155 0 0 0
VPN IPSEC upd 4056 0 0 0
VPN CTCP upd 0 0 0 0
VPN SDI upd 0 0 0 0
VPN DHCP upd 0 0 0 0
SIP Session 0 0 0 0
Logical Update Queue Information
Cur Max Total
Recv Q: 0 7 6588043
Xmit Q: 0 34 107757911
But few seconds later Secondary ASA become FAILED.
And i also did FAILOVER RESET command. After this command, secondary ASA became Standby Ready then few seconds later it became Failed again. Why does it become Failed again ? -
ASA 5520 Anyconnect License on Active/Standby Failover pair
Hi
Our customer has purchased 2 x L-ASA-AC-E-5520= Anyconnect Essentials VPN Licenses (750 Users)
Ive installed both activated licenses as per the cisco guides, I didnt get any errors on the install. I did a reload on both, they are both back up and running as active/standby but when I do a sh ver the license still shows "ASA 5520 VPN Plus License"
Am I being dumb and has this worked successfully or should it not now display Anyconnect when I do a sh ver
Any help would be much appreciated on this one please
Regards
GrahamThanks Marvin
Below is the show ver, but I was kind of expecting there to be a mention of Anyconnect if I had activated the license
We previously had the VPN Plus License, and it still shows VPN Plus
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 150
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
VPN Peers : 750
WebVPN Peers : 2
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions : 2
This platform has an ASA 5520 VPN Plus license. -
Cisco ASA Active standby failover problem
We have configured ASA Active standby failover with ASA5505 . When primary unit power off, secondary unit became active. when primary unit power on, then primary unit is becoming active again. i think for active standby setup there is no preemption. The real issue is when primary ASA became active after power on all the external connectivity getting down. Please see the below config,
ASA01# show run
ASA01# show running-config
: Saved
ASA Version 8.2(5)
hostname ASA01
enable password PVSASRJovmamnVkD encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 192.168.1.1 MPLS_Router description MPLS_Router
name 192.168.2.1 SCADA_Router description SCADA_Router
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
switchport access vlan 2
interface Ethernet0/3
interface Ethernet0/4
switchport access vlan 3
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.3.8 255.255.255.0 standby 192.168.3.9
interface Vlan2
nameif outside
security-level 0
ip address 192.168.1.8 255.255.255.0 standby 192.168.1.9
interface Vlan3
description LAN Failover Interface
ftp mode passive
clock timezone AST 3
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended permit ip any any
access-list inside_access_in extended permit ip any host MPLS_Router
access-list outside_access_in extended permit icmp any any
access-list outside_access_in extended permit ip any any
access-list outside_access_in extended permit ip any 192.168.2.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
failover
failover lan unit primary
failover lan interface FAILOVER Vlan3
failover key *****
failover interface ip FAILOVER 10.1.1.1 255.255.255.0 standby 10.1.1.2
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route-map Route_Out permit 1
match ip address inside_access_in outside_access_in
match interface inside
route outside 0.0.0.0 0.0.0.0 MPLS_Router 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
http 192.168.2.0 255.255.255.0 inside
http authentication-certificate inside
http authentication-certificate outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet 192.168.2.0 255.255.255.0 inside
telnet 192.168.1.0 255.255.255.0 outside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username admin password eY/fQXw7Ure8Qrz7 encrypted
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:1a8e46a787aa78502ffd881ab62d1c31
: endI suggest removing the failover configuration on both units and then re-add them, and then test.
Primary
failover lan interface FAILOVER Vlan3
failover interface ip FAILOVER 10.1.1.1 255.255.255.0 standby 10.1.1.2
failover lan unit primary
failover key KEY
failover
Secondary
failover lan interface FAILOVER Vlan3
failover interface ip FAILOVER 10.1.1.1 255.255.255.0 standby 10.1.1.2
failover lan unit secondary
failover key KEY
failover
Please remember to select a correct answer and rate helpful posts
Maybe you are looking for
-
How do I select more than one frame? (editing a movie in PS)
Fisrt time ive tried this. I want to do a quick selecton on a movie clip but can only seem to select 1 fram at a time. How can I select more than one frame? cheers jamie
-
How can i transfer music from my iPod touch to my new macbook?
I recently bought a laptop, and i can not transfer the music on my ipod touch onto it!? I also need to update my ipod, but if i do this i will lose what is on the ipod, and i have no back up because i cant get it onto my macbook! Is there any way to
-
Project info help needed..
I can not find where I can view the entire project info size. I know how to view each clip info size but not entire project size. So where can I view entire project info size. Thanks...Newbie to FCE.
-
Values are generating in the prepopulated fields from the XML data sourece I binded to the fields
Hello, Fairly new here. I am trying to insert the payrate and name values in a pdf document on LiveCycle. I created the XML file from our access database (about 1100 names), created the text fields using the same field names in the XML file, connect
-
Question about modifying the size of an existing column in a table
I am a new DBA. I am being asked to modify a column in an existing table that is populated with data. Our database is a 10g database, and the table name is Contacts. The column name is FName, and it is currently VARCHAR(10). It needs to be increased