E71 Camera Auto Focus Not Working

Dear Sir/Madam, Please help me out of this confusion. I wanted to know whether E71 model have Auto Focus feature in Camera, if yes the my mobile don't have that one. I recently purchased this model  just 4 months before and the camera quality is not good also.

Hi Joshymathew
How about pressing the "T" key?
Happy to have helped forum in a small way with a Support Ratio = 37.0

Similar Messages

  • IPhone 3Gs camera-auto focus not working; no focus instead

    Just got a new iPhone 3Gs. Wanted to test the camera since I hear it's so much better. The image never focuses. At first a box appears, dead center, like it should, but it doesn't focus. When I tap on the screen a box appears where I tapped, so it's responsive in that respect. But again, doesn't focus there.
    Help! I haven't used it yet -- is there a setting I need to set or something else I need to do (calibrate?) to get it to work?

    Do you have enough light for a photo? Have you tried taking a picture, and seen that it is out of focus (as opposed to fuzzy because you didn't hold it steady enough)? Is the lens clean?

  • Lumia 620 auto focus not working?

    im using lumia 620 .recently ive updated with new os and after that its camera auto focus is not working....every time i capture somthing gives blurry image...how can i solve this problem..?

    Have you checked your settings?
    If  i have helped at all a click on the white star below would be nice thanks.
    Now using the Lumia 1520

  • MHs-TS20 Auto Focus not working???

    For some reason the Auto Focus is not working on my Bloggie. Any ideas?

    If there are focusing issues in picture taking, keep in mind that you have to half press the shutter button to allow the bloggie to focus properly. The camera may have a hard time focusing on low light situations, subjects with less contrast or moving objects.
    It is normal that the camera may record blurry or unclear videos in low light. If the issue persists or happens in situations with ample light, you may reset the bloggie by holding down the power button for at least 7 seconds.
    If this post answers your question, please mark it "Accept as Solution."

  • Sx10 auto focus not working

    I have an SX10 I am evaluating for rollout but the unit I purchased does not focus properly. When auto focus is enabled, it tries to focus for several seconds, then stops before completing the focus. I tried setting it to manual focus but there is no obvious manual focus mechanism on the device.
    Is the SX10 I have faulty or is there some trick to getting the auto focus feature to completely focus instead of the current half focus it does.

    Hello Dave -
    I have an SX10 in my office and I haven't seen anything wrong with it not focusing correctly on me.  Is there anything, even the littlest thing between the camera and yourself that is in the view of the camera that it could be focusing on instead?  For instance, mine is sitting on top of a table, and if I have the camera pointed down far enough to where it sees the table top, it will pick up and focus in on the edge of the table and not me that is farther away in the image.

  • Lync 2013 A/V Conference meeting with Logitech BCC950 conference cam auto sense not working

    Hello All,
    I have Lync 2013 server's configured & everything is working fine. We are doing the A/V Conference meeting by connecting Logitech BCC950 conference cam.
    Logitech conferencecam connected in the conference rooms. Now on one user laptop we have connected this logitech cam to the laptop & meeting is started, below below issues are:
    1) In the middle of the meeting device getting automatically disconnected. Tried to manually select the Integrated WebCam but it's not getting detected.
    2) Whenever we connect this Logitech cam it should get automatically selected as default device in Lync 2013 client which is not happnening.
    3) If the Logitech cam disconnect it should get detected Inbuilt Web Cam
    Can someone help us to resolve this issue.
    Any help really appreciated
    Thanks & Regards
    Anand S
    Thanks & Regards Anand Sunka MCSA+CCNA+MCTS

    Hello Logimg1,
    Thanks for your reply & we have checked below options:
    1) In the middle of the meeting device getting automatically disconnected. Tried to manually select the Integrated WebCam but it's not getting detected.
    LogiMG>  I have not experienced this issue, but could you tell me if the Blue LED in the camera is lit when you experience this disconnect?  It is strange that you can't switch to the Integrated camera.
    Anand : Cusotmer faced this issue by I tried to reproduce but I haven't faced this issue.
    2) Whenever we connect this Logitech cam it should get automatically selected as default device in Lync 2013 client which is not happnening.
    LogiMG>  Lync remembers the last camera selected and the OK button is pressed.  If you use the 'X' it will not be remembered.  What are the behaviors of the camera at this point?  Do you see it go through the connection sequence?
    Anand : First time we need to make as a default device as well as default communication device under Control Panel sound options.
    3) If the Logitech cam disconnect it should get detected Inbuilt Web Cam
    LogiMG> What is the state of the LED for either camera?  If it is on, then the camera(s) is streaming video.
    Anand : Customers laptop faced this issue, but when I was tried it's selecting Inbuilt Cam
    Thanks
    Anand S
    Thanks & Regards Anand Sunka MCSA+CCNA+MCTS

  • Iphone 4s Running Ios(7.1) Camera Focus Not Working Like Text On book It Showed Blurey Text & My Friend Also Same Modle His Camera Focus Perfectly..Is Is Possible To Fix It...Thnx Every 1

    Iphone 4s Running Ios(7.1) Camera Focus Not Working Like Text On book It Showed Blurey Text & My Friend Also Same Modle His Camera Focus Perfectly..Is Is Possible To Fix It...Thnx Every 1

    Hello SajidChaudhary,
    Thanks for using Apple Support Communities.
    For more information, take a look at:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/ts2802
    Camera isn't functioning or has undesired image quality
    If the screen shows a closed lens or black image, force quit the Camera app.
    If you do not see the Camera app on the Home screen, try searching for it in Spotlight. If the camera does not show up in the search, check to make sure that Restrictions are not turned on by tappingSettings > General > Restrictions.
    Ensure the camera lens is clean and free from any obstructions. Use a microfiber polishing cloth to clean the lens.
    Cases can interfere with the camera and the flash. Try gently cleaning the lens with a clean dry cloth or removing the case if you see image or color-quality issues with photos.
    Try turning iPhone off and then back on.
    Tap to focus the camera on the subject. The image may pulse or briefly go in and out of focus as it adjusts.
    Try to remain steady while focusing:
    Still images: Remain steady while taking the picture. If you move too far in any direction, the camera automatically refocuses to the center.
    Note: If you take a picture with iPhone turned sideways, it is automatically saved in landscape orientation.
    Video: Adjust focus before you begin recording. You can also tap to readjust focus while recording. Exiting the Camera application while recording will stop recording and will save the video to the Camera Roll.
    Note: Video-recording features are not available on original iPhone or iPhone 3G.
    If your iPhone has a front and rear camera, try switching between them to verify if the issue persists on both.
    Have a nice day,
    Mario

  • Tandberg mxp 6000 camera auto focus

    Hello sir,
                  I saw the issue form Tandberg mxp 6000 camera auto focus.
    when I zoom the camera it focus image blurring after zoom out fully its blurring few minutes and its clear but its not focus correctly. I change camera and check the different location its same. conference room room size is approximately 15 to 18 feet length. pls tell any other option to solve the issue. I also do software upgrade and downgrade also.

    Does it matter? NO REGISTER packets arrived to server, i was sniffing traffic.
    Problem solved just after i entered valid DNS server address in IP parameters. Why would it need DNS if i'm using direct IP addresses...
    Anyways, my SIP server (Asterisk) does not support duo-video and because there is two video streams in SDP message, it choses wrong RTP port and streams other's side video to presentation channel.

  • HT3964 my built-in isight camera will still not work on my macbook pro after completing smc reset.  The green light comes on but no video.

    my built-in isight camera will still not work on my macbook pro after completing smc reset.  The green light comes on but no video. 
    Any Suggestions?

    Restart the computer.

  • My iPhone 5 rear camera was not working, now the rear camera is also not working. I have procured the phone in 2012 from San Fransico. USA Can anyone help me, please?

    My iPhone 5 rear camera was not working, now the rear camera is also not working. I have procured the phone in 2012 from San Fransico. USA Can anyone help me, please?

    No one here can help you. If your phone is no longer under warranty, a third-party repair shop will most likely be your best bet. You can't mail the phone to Apple, in the US, as Apple does not accept international shipments. You could mail it to a friend/relative, in the US, & they could take it to an Apple store for you. Some Apple stores repair iPhones. Otherwise, you're looking at an out of warranty replacement.
    Good luck.

  • My camera  icon is not working on my sms so i cant send picture with sms? what to do?

    My camera  icon is not working on my sms part?
    so i cant send picture with sms? what to do?

    Double tap Home button, delete Camera app in multitask-bar.
    Do a
    Reset: Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Note: You will not lose any data
    By the way, picture go through as MMS not SMS, do you have a SMS/MMS plan with your carrier?
    Have you spoken with them?

  • I have CS5 and a d-600. I would like to use camera raw but not working. I downloaded CR 7.3 and still not working. Do I need to upgrade to CS6 ..or just throw it all out the window and get rid of my d-600 ?

    I have CS5 and a d-600. I would like to use camera raw but not working. I downloaded CR 7.3 and still not working. Do I need to upgrade to CS6 ..or just throw it all out the window and get rid of my d-600 ?

    it allows you to use your cr files, Adobe - Adobe Camera Raw and DNG Converter : For Windows
    Camera Raw: How to use Adobe DNG Converter - YouTube

  • Auto brightness not working in ios6

    I updated my iPad (3rd gen) to ios6, but when the update is complete i found that the auto brightness not working, when i use the ipad on dark room the brightness not changing, when i use ios5.1 it changing.. Any solution and actually the problem is on ios or in the hardware? Looking for help asap...

    Well my device is different and since it is a iPhone 5, it is not being updated to iOS 6 but the issue is exactly the same. From my mind this could be up to software but also could be from an hardware issue. The thing is that even if it worked before iOS 6 for you the new software could have revealed hardware conflicts since the software interacts different with the hardware for some features. This would be the worst case scenario because I know that normally iPhone 4 devices if not the 8GB model will be out of warranty. For me this is just a small issue since my warranty is still one year :(
    I have contacted apple care for this issue and have get the info that it will be escalated to the engineering team, for further investigation. As I know there was also an issue with some proximity sensors at the beginning if the iPhone 4 models and I think there was an software fix for a lot of them. Hope for the best!!!
    I have also done a lot of Troubleshooting, reseted settings, content and settings, restored in dfu and recovery mode, restored with new .ipsw (iPhone OS), restored on different pc (so even this step gas downloaded a totally new .ipsw file), first on a Mac!
    Next step wis that I will let the battery drain low entirely, a Troubleshooting idea of an friend. This might empower the entire hardware for a restart. I am not really believing in this step but I will give it a try :)

  • AUto attendant not working

    Auto attendant not working .....
    If i assign AA script Transfer_v02.aef then i hear an just 1-2 seconds the script after that again it is just ringing ...
    Is there Option to set
    Please press the extension which you want to Call ...
    Eg: if i press 222 that time it should ring the 222 extension
    Please help this is the first time i am working on this stuff
    If i chnage the scrpt file then i can hear auto attendant not initiazlised..  please find the attched screen shot and back file for more details.
    Best Regards
    Shabeel

    Hi KMS, check the codec used between that GW using the FXO and the CTI RP.
    Check also the Calling Seach Space
    GW should be able to reach CTI Route Point and CTI ports partition.
    If you try other extension it works fine?

  • Camera Raw CS6 not working properly

    I have upagraded from Ps Cs5 to CS6.
    I open a file in CR, and modify the exposition. After that, I modify the clarity: immediatly, the exposition goes back as it was before the modification ...
    After the work on CR, I finish the file and go back to bridge: the image is not modified ! But if I dobble click on the same image in bridge, the file is opening in CR with the modifications: so this modifications are note visble on bridge ...
    Some body can help me ?
    I work with the last version of Br and Ps CS6.
    Thanks,
    Michel,   [email protected]

    Thanks a lot, Adriana, it is working ! You are right, it is the Nike plugins responsibility. Everything is OK now.
    Salutations and many thanks from Guadeloupe, French West Indies
    Michel GOGNY-GOUBERT
    Le 4 mars 2014 à 17:42, adriana ohlmeyer <[email protected]> a écrit :
    Re: Camera Raw CS6 not working properly
    created by adriana ohlmeyer in Adobe Camera Raw - View the full discussion
    If you have Nik plugins installed, please check reply # 8 on this thread:
    http://forums.adobe.com/message/6045415#6045415
    Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6179192#6179192
    Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6179192#6179192
    To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6179192#6179192. In the Actions box on the right, click the Stop Email Notifications link.
    Start a new discussion in Adobe Camera Raw at Adobe Community
    For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

Maybe you are looking for