EA 6200 & other EA series connectivity to "smart" TV
There is a known issues about the connectivity with my "smart" TV (ie: LG LM 8600) which is already known and discussed in other forum (http://forums.whirlpool.net.au/archive/1958013).
My issues is that my TV could only connected to my old linksys E1200 ethernet wired connection without any problem. However, when I upgrade to EA 6200 few months ago, I have tried both gigabit wired and wireless (2.4 & 5) connection and they all disconnect after a period of time. I have complained this matter to LG but they never response as usual.
I know the culprit is the TV. But is there anyway to set the wired connection to 100mb ehternet instead of gigabit just like my E1200 with DD-WRT where they could set the limitation of each Lan port?
Besides, in considering sustainable environment, could Linksys has the options of scheduled power on and off in the next firmware?
Cheers!
Ya, theres a recent post about a Samsung TV however thats a WiFi adapter issue on the TV. We presume that if other devices on the router connect and work well that this pariticular TV is the problem. There isn't a LAN port speed setting and most ruoters are always automatic in this regard and lays this feature ability at the foot of the client side HW if Mfrs choose to support this feature. The only other way to test your TV out on the LAN and stepping down from GB to 100Mb is to install a external 100Mb network LAN switch then test. Another option might be to install a 100Mb LAN supporting wireless bridge on the TV then you could connect the bridge to the routers WiFi.
Similar Messages
-
How to connect my smart tv to internet using Apple TV?
Is it possible to connect my smart tv to internet through Apple TV?
I am wondering if Apple TV can connect my TV to internet or should I get a TV wireless device
-
Cannot connect to Smart Tee input pin...
Hello i have some problem with the picture on my TV@nywhere card it actually started when i upgraded my DivX version 5 something too 6.2.2 ... The image is all black but i can still hear the sound And this message appear when i start Tv@anywhere plus " Cannot connect to Smart Tee input pin..."
Can someone please help meNo i was hoping i didnt need to... But i guess i have no choice
-
After connecting my computer to Microsoft for updates it has locked me out of administrative access. When wanting to install a software it keeps on saying connect a smart card. I have tried to go on start-Run -and typed gpedit.msc and it says access denied
you do not have permission to perform this operation Group policy error. Please help on how l can resolve this problem. I cant even do any other setting changes on my machine. I am using windows 8.1 pro wit media center on an asus 64bit.Hi,
Have you any other Administrator account?
If yes, please log on with that account to disable the Smart Card Logon.
Start --> Run --> type gpedit.msc and press Enter.
Navigate to:
Computer Configuration\Administrative Templates\Windows Components\Smart Card
Right-click Turn on Smart Card Plug and Play service and click Edit to disable.
If no, please logon with the built-in administrator to do that if it's enabled.
Otherwise, there is no any other method except reinstallation.
Karen Hu
TechNet Community Support -
Unable to connect Logitech Smart radio to Home Hub...
I am trying to connect my Logitech smart radio via wireless to my homehub 3.
It has connected successfully in the past but is now failing to connect with the comment "unable to connect using password nnn"
nnn = my wirless key.
I have reset the radio to the factory defaults, powered off and on the hub all to no avail.
Other devices can connect via wireless using this key.
Any help would be apprecaited
Thanks
AndyThere is some help on this page.
Wireless connection problems
Its most likely an encryption issue.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones. -
Until Sky stop prefixing programmes with the moniker NEW:, series link and Smart Series will not work because the planner thinks they are another programme. E.g. last night UNDER THE DOME restarted, and was set in my Smart series. Unsurprisingly, it did not record as the programme was called NEW: UNDER THE DOME.,...... Not technical, you can keep on rebuilding your planners all day, but the solution is obvious, except to Sky, no surprise there......
The 'new' issue (which was fixed I think in R010) never stopped programs recordings, it just mixed up the stacks if you had episodes both with 'New' and without. This has been fixed in the majority of cases.
Your issue appears to be entirely different. Did the next episode (ie last night's Falling Skies) appear in the Scheduled Tab at all and fail to record or didn't it put it in after last week's episode?
is correct in that it is up to the channels themselves what constitutes a series. For example, it is the BBC who has decided that the new Top Gear specials being shown are not part of the aborted series, so Sky boxes won't have picked them up automatically. -
Cannot connect to Smart Tee input pin... [Windows 7 64 bit]
Hi TV Tuner users! I need some help.
I've been searching on this forum and all over the web for a solution. I hope some of you guys might have a solution.
I have a TV @ anywhere Plus and run Windows 7. The card has previously worked but for the past few months it has malfunctioned.
When I start the TV @ anywhere recording software I get following errors:
"Cannot connect to Smart Tee input pin..."
"Cannot render audio renderer (5001)..."
"Cannot init Direct show interface... (1001)"
I have not made any major adjustments to the computers drivers or hardware. I've reinstalled and installed, and reinstalled different versions of the driver and software. I've even switched PCI port.
So I'm a bit confused. Anyone having an idea for a solution?
This guy (https://forum-en.msi.com/index.php?topic=124889.0) even formatted his harddrive. It's an old post, but maybe you've figured out something since that post?
Regards
ErlingNo i was hoping i didnt need to... But i guess i have no choice
-
I wanna connect to smart card by my card reader(ACR38U model). I wanna use java to connect , I mean connect, enter pin, and ready for process.... Do you have any code related wiith this?
I can connect Card reader which does not a contactless and use standand JP/CSC and user jpcsc.jar to connect
this get detail
public CardBean getCard()throws Exception {
CardBean cardBean = new CardBean();
// TODO Auto-generated method stub
log.info("EstablishContext(): ...");
ctx = new Context();
ctx.EstablishContext(PCSC.SCOPE_SYSTEM, null, null);
String atrValue = null;
log.info("Wait for card to be inserted in any reader ...");
State state = null;
do {
// blocks until a reader is available
ctx.GetStatusChange(PCSC.INFINITE, null);
// block until card is inserted
state = ctx.WaitForCard(PCSC.INFINITE);
} while (state == null);
log.info("Card inserted into " + state.szReader);
atrValue = Apdu.ba2s(state.rgbAtr);
log.info("Card ATR is " + atrValue);
atrValue = atrValue.substring(atrValue.indexOf(" ") + 1, atrValue
.length());
log.info("Connect to card " + state.szReader);
log.info("Card ATR is " + atrValue);
card = null;
try {
card = ctx.Connect(state.szReader, PCSC.SHARE_EXCLUSIVE,
PCSC.PROTOCOL_T0 | PCSC.PROTOCOL_T1);
} catch (Exception e) {
System.out.println("The smart card cannot be accessed because of other connections outstanding.");
e.printStackTrace();
cardBean.setAtrValue(atrValue);
cardBean.setCard(card);
cardBean.setCtx(ctx);
return cardBean;
this is execute method
public static List<String> executeAPDU(Card card, List<String> lAPDU) {
log.info("executeAPDU .");
List<String> lResult = new ArrayList<String>();
for (int i = 0; i < lAPDU.size(); i++) {
byte[] ba = null;
try {
log.info("lAPDU message " + (String) lAPDU.get(i));
ba = Apdu.s2ba((String) lAPDU.get(i));
} catch (Exception e) {
e.printStackTrace();
log.info("invalid APDU: " + e.getClass() + ", "
+ e.getMessage());
String result = null;
try {
byte[] response = card.Transmit(ba, 0, ba.length);
result = Apdu.ba2s(response);
result = result.substring(result.indexOf(" ") + 1, result.length());
log.info("result apdu. " + result);
lResult.add(result);
} catch (Exception e) {
log.error("sending APDU failed: " + e.getClass()
+ ", " + e.getMessage());
return lResult;
You can download exampel from this link
http://www.linuxnet.com/middle.html
but I have problem that I don't how to connect with contact less
Does any now can help me?
ps. I don't know how to download jpcsc.jar to I got it from my friend -
My ipod touch (4th) suddenly wont connect to my wifi. It connected fine before and all of my other electronics (tablets, computers, laptops, gaming systems, etc.) are connected and working completely fine. I tried turning the wifi setting on my ipod on/off as well as the actual ipod itself. I also tried resetting the network settings but neither of these options worked. Any suggestions on what I should do?
Does the iOS device connect to other networks?
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
Hey everyone, I have been having this problem for about a day or two now. I have an iPhone 4, and have iOS 7.1.2. Basically, my iPhone will connect to my home WiFi sometimes, but it randomly loses connection and won't connect for hours upon hours. I have tried turning it on and off multiple times as well as resetting the network settings. I know that it is not my network's problem because a member of my family has an iPhone 5S, and it works fine with the WiFi, along with all of my other devices. This issue is getting very annoying as I don't like to use my cellular data at home since it is limited. Please help me!!
Does the iOS device connect to other networks? If yes that tends to indicate a problem with your network.
What happens when it fail to connect?
----- Does the iOS device see the network?
----- Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
cannot connect to home wi-fi connection with my 2nd gen itouch even after following most troubleshooting solutions. i have 2 5-gen itouch ipods and a kindle fire hd 8.9 that can connecto to my wi-fi network and even download from my e-mail accounts with no problem. it had no problem connecting with my old a/b/g netgear router nor the first time i installed my new netgear wndr3700v3 router. since then, no connection. don't know what happened.
helpDoes the iOS device connect to other networks?
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router
- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar
Could it be this:
iOS: Wi-Fi or Bluetooth settings grayed out or dim
One user reported that placing the iPod in the freezer fixed the problem. A trick that works frequently with iPhones:
Settings > AirPlane Mode ON, Do Not Disturb ON
Power down and wait 5-10 minutes
Power up
Settings > AirPlane Mode OFF, Do Not Disturb OFF
If not successful, an appointment at the Genius Bar of an Apple store is usually in order.
Apple Retail Store - Genius Bar -
My MacBook Pro with Retina display displays power point and not other windows when connected to a projector. Can anyone help out please?
You should also ask this in the MacBook Pro forum. This is the forum for the white and black plastic MacBooks that were discontinued in 2010. You should also post this question there to increase your chances of getting an answer.
https://discussions.apple.com/community/notebooks/macbook_pro -
How to count Sent SMS in E63 and other E series No...
Hi...
How to count Sent SMS in E63 and other E series Nokia phone
I tried some software but they are not made for E63 or else its need to purchase.
Expecting solution.In Menu-> log you can filter your messages for counting. You can export the log to e.g. Excel on PC with LogExport.
http://tinyhack.com/freewarelist/s603rd/2007/03/02/logexport/
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009 -
Upgraded to Maverick. Now cannot connect to wifi. All my other devices will connect. Have rest wireless hot spot switch and cable modem. Other devices still connect but MacPro does not. MacPro wireless is self assigning an IP address blocking access. It will connect if I connect to my iPhone hot spot via wifi. Any ideas?
If you follow this video you'll see how to delete your WiFi AP from the OS, this will allow you to select it again which I feel will correct your problem.
https://app.box.com/s/fe7v7h7kywjr23spumqp -
I have two iPads and one is connected to the internet but my other iPad was connected then was not and since then I have not been able to add my internet back onto my iPad it only says cannot connect to the server any help would be great thanks
If you are having WiFi problems it is necessary to isolate whether the problem is with your network or your iPad. Note: Do NOT consider your network to be blameless if some other devices can connect to it.
First, test your iPad on some other WiFi networks: a friends, Starbucks, Barnes & Noble, etc.
If it works well there then the problem is probably with your network. Try restarting your WiFi router by removing power for 30 seconds. If that does not help check for a firmware update for your router. If none exists which corrects the problem consider replacing the router.
If your iPad does not function well on other networks it possibly has a hardware problem. You could try Settings > General > Reset > Reset Network Settings to see if that corrects the problem. If not, contact Apple Support or visit an Apple store for evaluation. They can provide a replacement if your iPad is bad.
If you need more help please give the make, model, and version of your WiFi router and how you have it configured.
Maybe you are looking for
-
Unable to restore from my icloud backup
I backed up my 3gs via iCloud and purchased a new 4s. I was expecting to be able to restore from my iCloud backup, but when i tried, it said there was no backup information. I did reset the 3gs before attempting to get the restore started on the 4s.
-
Using a Statefull Session Bean with RMI on Multiple JSP pages
Heya all, i have a JBoss server running with a statefull bean on it. I want to use it on my JSP pages. But every time I start my JSP-page a NEW INSTANTION of the bean is created! For each user using my page, I want ONE bean. Is there anyway to do thi
-
Ad Hoc Tasks Does anyone know how to have an email automatically triggered onc ethe "Done" button has been clicked on an Ad Hoc task? Thanks in advance, Shane
-
Can anybody explain all the details about idoc like configuration settings etc..
Hi all can anybody explain the idoc configuration settings, communication channels sender and receiver settings
-
Dear Gurus I have a situation: Employee's like GM works on different locations e.g., Plant A & Plant B. Both Plant A & B have different Cost Centers. I want to distribute GM's Cost on both Centers (Activity Allocation). Is is possible? if yes then