EA2700 and remote accessing DVR

Does anyone have a solution for router settings to allow remote access to
DVRs both windows and Linux?
Solved!
Go to Solution.

Remote access feature is already enabled on the router.
Found these link sfrom the web that might help.
Enabling Remote Management on a Linksys Router
http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=98e570a093ae4ccda0d7cfb7fda97df7_4023.xml&pid=80&r...
http://www.ehow.com/how_7469803_remote-access-dvr.html
For Linux:
http://www.howtoforge.com/configure-remote-access-to-your-ubuntu-desktop

Similar Messages

Cannot login to Cisco Jabber 10.5.1 over Mobile and Remote Access

Hi,
We have deployed sucessfully VCS Expressway-C and VCS Expressway-E with only 1 zone which is "Unified Communication Traversal" and is for Mobile and Remote Access only. VCS-C and VCS-E are communicating and in statuses everything is active and working. Also VCS-C can communicate with CUCM and CUP (both version 10.5).
Problem is when I deploy Cisco Jabber 10.5.1 on computer outside of LAN and without VPN it start communicating with VCS-E, ask me for accepting certificate (we have certificate only intenally generated on Windows CA) and after that it is trying to connect and after few seconds it will tell me that it can't communicate with server.
Did any of you had same problem or can you advice how to troubleshoot? In Jabber logs there is only something like "Cannot authenticate" error message, but when I startup VPN I can authenticate without any problems.
Thanks

On Expressway-C are your HTTP Allow Lists setup properly? By default, and auto discovered CUCM and IMP should be listed via IP and Hostname, but if not, you'll need to insert manually.
Also, you can look at the config file your Expressway-E would be handing out to Jabber via this method.
From the internet, browse to:
https://vcse.yourdomain.com:8443/Y29sbGFiLmNvbQ/get_edge_config?service_name=_cisco-uds&service_name=_cuplogin
Where:
vcse is your Expressway-E hostname (or CNAME/A record)
yourdomain.com is your own domain
The first directory is your Base64 encoded domain name, remove and trailing equal signs (=)
The XML returned is basically the DNS SRV record information available as if internal for _cisco-uds and _cuplogin
TFTP DNS SRV is optional if you configured TFTP in IMP for your Legacy Clients.

Vpn site to site and remote access , access lists

Hi all, we run remote access and site to site vpn on my asa, my question is Can I create an access list for the site to site tunnel, but still leave the remote access vpn to bypass the access list via the sysopt command, or if I turn this off will it affect both site to site and remote access vpn ?

If you turn off sysopt conn permit-vpn it will apply to both your site to site and remote access vpn...all ipsec traffic. You would have to use a vpn-filter for the site to site tunnel if you wanted to leave the sysopt in there.

Exchange Server 2013 and Remote Access VPN on a single server running Windows Server 2012?

Just by way of background, I have been installing and administering network servers, e-mail systems, VPN servers, and the like for many years. However, my involvement with Exchange and Windows Server has been mostly on the forensics and data recovery
level, or as a (sophisticated) user. I have never tried to deploy either from scratch before. My deployment experiences have been mostly with Linux in recent years, and with small private or personal "servers" running such cutting edge
software as Windows XP back when it was new. And even NetWare once.
When a client asked me if I could set up a server for his business, running Exchange Server (since they really want Outlook with all of its bells and whistles to work, particularly calendars) and providing VPN access for a shared file store, I figured it
could not be too difficult given that its a small business, with only a few users, and nothing sophisticated in the way of requirements. For reasons that don't bear explaining here, he was not willing to use a vendor hosting Exchange services or cloud
storage. There is no internal network behind the server; it is intended to be a stand-alone server, hanging off a static IP address on the Internet, providing the entirely mobile work-force of about 10 people with Exchange-hosted e-mail for their computers
and phones, a secure file store, and not much else. If Exchange didn't need it, I would not need to install Active Directory, for example. We have no direct need for its services.
So I did the research and it appears, more by implication than outright assertion, that I should be able to run Windows Server 2012 with Exchange Server 2013 on a server that also hosts Remote Access (VPN only) and does nothing else. And it appears
I ought to be able to do it without virtualizing any of it. However, I have spent the last three or four days fighting one mysterious issue after another. I had Remote Access VPN working and fairly stable very quickly (although it takes a very
long time to become available after the server boots), and it has mostly remained reliable throughout although at times while installing Exchange it seems to have dropped out on me. But I've always been able to get it back after scrounging through the
logs to find out what is bothering it. I have occasionally, for a few minutes at a time, had Exchange Server willing to do everything it should do (although not always everything at the same time). At one point I even received a number of e-mails
on my BlackBerry that had been sent to my test account on the Exchange Server, and was able to send an e-mail from my BlackBerry to an outside account.
But then Exchange Server just stopped. There are messages stuck in the queues, among other issues, but the Exchange Administration Center refuses now to display anything (after I enter my Administrator password, I just get a blank screen, whether on
the server or remotely).
So, I am trying to avoid bothering all of you any more than I have to, but let me just begin with the basic question posed in the title: Can I run Exchange Server (and therefore Active Directory and all of its components) and Remote Access (VPN only) on
a single Windows Server 2012 server? And if so, do I have to run virtual machines (which will require adding more memory to the server, since I did not plan for it when I purchased it)? If it can be done, can anyone provide any pointers on what
the pitfalls are that may be causing my problems? I am happy to provide whatever additional information anyone might like to help figure it out.
Thanks!

An old thread but I ran into this issue and thought I share my solution since I ran into the same issue. Configuring VPN removes the HTTPS 443 binding on the Default Site in IIS for some strange reason; just go and editing the bindings, add HTTPS and things
should be back to normal.

Active directory domain services stopped after removing routing and remote access role

Hello everyone;;
I am in deep trouble.. I did install routing and remote access and then lost connection to the server remotely. Then I connected a monitor to the server and removed the role... then it asked me to restart the server . After logging back in I found
all my active directory service has gone... I can see red cross on active directory domain services.. Also I am able to ping other pcs but other pcs cannot ping my server..
However when I go into the active directory services, it shows all services are running except file replication service. I have tried to start that service but it give error 1053 error..
My server in between loses LAN connection... I dont know what is going on.. Please help!!!
My server is win 2008 R2 ser pack 1
Only one DC....
Has fixed ip,
no DNS server running..

Hi,
The File Replication Service Start Error 1053 error can be caused by damaged Windows system files. Corrupted system files entries can threaten the well-being of your computer. Many events can result in creating system file errors.
Please refer to the articles below to troubleshoot the issue:
File Replication Service Start Error 1053
http://repairerrors.net/file-replication-service-start-error-1053.html
Please Note: Since the website is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.
Regards,
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Win 7 Pro 64 occasionally fails to connect using IKEV2 to Win2008R2 Routing and Remote Access server

I'm a networking guy and having this troubling VPM issue that I can't find.
I have a number of VPN connections from my Win7Pro 64 PC to various customers. Their end points are all Windows Routing and Remote Access on Windows 2008R2 STD servers.
Every once and a while I will hang at Verifying User ID and Password and eventually get ERROR 809. Change the security type on my VPN connection from IKEV2 to PPTP - never an issue, connects in right away.
I can also try from another PC (at the same or alternate location) to get into that same server using the same credentials and access - no issue using either IKEV2 or PPTP.
This has happened at various times to various customers. Here is what I know it is not:
- Not the local or remote routers or Firewalls since I can always get in from other PC's going through the same network. Even so, tried rebooting all several times
- Not an ISP issue at either end since I can always get into other IKEV2 servers from the same PC and from other PC's to the server I can't from my PC.
This leads to the only logical conclusion. It is something to do with my Win7Pro 64 PC but for the life of my I can not find it.
I have obviously tried rebooting the Win7Pro PC. I have also tried recreating the VPN connection several times. Nothing.
Help!

Hi,
I know that you've mentioned that it is not a issue about firewall or router settings, but this error usually comes when some firewall between client and server is blocking the ports used by VPN tunnel.
so to allow IKEv2 traffic, please make sure to configure the network firewall to open UDP ports 500 and 4500, and to allow IP protocol 50.
If that is not possible, deploy SSTP based VPN tunnel on both VPN server and VPN client – that allows VPN connection across firewalls, web proxies and NAT
You can refer to this blog
http://blogs.technet.com/b/rrasblog/archive/2006/06/14/which-ports-to-unblock-for-vpn-traffic-to-pass-through.aspx
Regards
Yolanda
TechNet Community Support

Error 1053 when starting the Routing And Remote Access service

Hi all,
When I tried to start the "Routing And Remote Access" service on Windows 8.1 I got an error message as follow.
Could some one help me please.
Than's.

Hi MRAB,
Please check if all dependences are enabled first.
Then set the start type to Automatic.
Does this issue still occur after a restart?
Alex Zhao
TechNet Community Support

Routing and Remote Access Logs (Windows Server 2008 R2)

Hi,
I have a Windows 2008 R2 server running Routing and Remote access and users are using PPTP VPN's to connect to our network.
I have been asked to find logs for the following for connections in to our server
Username used for connection
Computer Name
IP Address used by computer connecting
Start/End time of VPN session
Date
Encryption used
I found an article stating to enable RRAS logs you need to run the following command
To enable RAS logs run command “netsh ras set tracing * enabled” and found a series of logs created in this location C:\Windows\tracing
None appear to contain the information I am looking for and was wondering if I was doing this correctly and if not how I am meant to extract this information?
If you require any more details just let me know.
Kind Regards
David

Hi,
I can’t sure which article you have read, but fur the 2008R2 the RAS to enable the log and the debug log in the KB is descried like this, I recommend you to try the KB
mentioned method.
To configure RRAS to enable logging
1. Start Server Manager. Click Start, click Administrative Tools, and then click Server Manager.
2. In the navigation tree, expand Roles, and then expand Network Policy and Access Services.
3. Right-click Routing and Remote Access, and then click Properties.
4. On the Logging tab, select Log errors only, Log errors and warnings, or Log all events, depending on how much information you want to capture.
5. Click OK to save your changes.
The related KB:
RRAS: Logging should be enabled on the RRAS server
http://technet.microsoft.com/zh-cn/library/ee922651(v=ws.10).aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Would you tell me If window server installed with "routing and remote access" can output firewall logs.

I install "routing and remote access" into Window Server and make it work as a firewall.
When connections are accepted or denied at firewall, would you tell me if the firewall can output the logs ?
If that function can, would you tell me how to configure ?
Thanks.

Hi Kohenro31,
I'm a little confused about configuring RRAS to work as firewall, cause we usually deploy RRAS as VPN connection, router etc, would you please post more information in detail?
Routing and Remote Access Service：
http://technet.microsoft.com/en-us/library/cc754634(v=ws.10).aspx
In addition, to view firewall event logs please check this article:
Viewing Firewall and IPsec Events in Event Viewer:
http://technet.microsoft.com/en-us/library/ff428140(v=WS.10).aspx
To enable RRAS logs, please check this article:
Enabling logs for RRAS:
http://blogs.technet.com/b/rrasblog/archive/2005/12/22/enabling-logs-for-rras.aspx
If I have any misunderstanding, please let me know.
Best Regards,
Anna Wang

Set value when a virtual, analog modem should answers in Server 2012 Routing and Remote Access

Hi there,
I googled for hours on the following problem:
We have a Routing and Remote Access Server with an Dialogic Diva PRI card (30 lines). The card provides an analog, virtual modem pool. All this runs on Windows Server 2012 (without R2).
My problem is that the client will be connected after 3 or 4 rings on the line (I can not hear properly with our client device), but it should be connected after the first ring.
Under Server 2000 there was the possibility to set the value "NumberOfRings" in the registry and / or set the modem to ATS0 = 1. Both ways do not work in Server 2012.
Can anyone tell me how it works under 2012?
Thanks and regards
Andre

I assume you followed Dialogic's instructions for configuring the device on Windows Server 2012. It would most likely make more sense to contact Dialogic if you are having issues. They support the product. If it is not working according
to their configuration instructions, they are in the best position to be able to answer your questions.
. : | : . : | : . tim

Server 2003 routing and remote access not passing VPN traffic

I've inherited a network that has two IP scopes that are routed through a Windows 2003 server with Routing and Remote Access. I can ping both sides (we'll call them HQ and Plant) internally. My firewall has an IP from the HQ IP scope and when
I connect via VPN, I can see all the devices on the HQ network including the network card that is in the routing server for that "side". However, if I'm connected via VPN, I cannot get to any of the IPs on the Plant side, not even the card
in the routing server. The buck stops on the server.
I should mention, that the firewall assigns IP addresses that are on the HQ scope, so all VPN connections will have an address from that side.
I'm lost on how to get this set up so my VPN traffic coming in from the HQ side can be routed to the Plant devices.

Hi,
To be honest, your statement confused me a bit.
VPN is used for external client get access to internal resource. When we setup VPN server, we usually have two NICs. We need choose a NIC that will be used when client initiate
a connection request. I prefer to call it external NIC card. The internal one will work as DHCP relay agent. So this is a single way connection. You cannot dial from internal to external.
If I misunderstood you, please elaborate what you are trying to do.
Hope this helps.

Routing and Remote access - internal network not accessing internet through public network!

Hello,
Good Evening to all.
I got an issue in routing and remote access on windows 2003 server. This server is already configured as File server, domain server and Application server. Also configured as router (through routing & remote access) for connecting three different
network to each other. So This server has three NIC card installed and each NIC card represent separate network.
three different network are - 192.42.160.0/24 , 192.42.161.0/24, 192.42.162.0/24
Three NIC card installed on server as with following IP address -
NIC -1 = 192.42.160.220 , Sub- 255.255.255.0 , Gateway - NO
NIC -2 = 192.42.161.220 , Sub- 255.255.255.0 , Gateway - 192.161.220.112 (This ip for internet access so 4g router IP)
NIC -3 = 192.42.162.220, , Sub- 255.255.255.0 , Gateway - NO
Now the issue is I can reach to internet & (also pinging to router ip 192.42.161.112) from only one network that is - 192.42.161.0/24 , BUT when I trying to access internet from another two network (192.42.160.0/24 & 192.42.162.0/24) I cant access
it and moreover can't ping to internet router ip - 192.42.161.112...
So how I can access to internet from other two network also?
I was already configured static routing for all three network but still I was not success. really I don't know what exactly static routing it should be done in routing & remote access so that all three network can reach to internet?
Sorry if I am not able to explain properly. Please let me know if you need more explain on this...
Thanks to all.

Dear Milos,
I am happy to hear from you....
1.- Actually the setup was done long before by another guy and right now I don't want to change it.
Nice to hear from you! Thank you so much. Actually this is first time I am using technet forum upon the suggestion from one of the my friend. So any your help from you will help me a great in this issue...
I ran the route print command and given follow are the results.
I have only added the default route as per the below routes. Please guide me know how to add other static routes for three network.
D:\Documents and Settings\Administrator>route print
IPv4 Route Table
===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x2 ...00 30 05 ad 8f 5c ...... Broadcom NetXtreme Gigabit Ethernet - Teefer2 Mi
niport
0x3 ...00 0e 0c a7 c4 f8 ...... Intel(R) PRO/1000 GT Desktop Adapter - Teefer2 M
iniport
0x4 ...00 0e 0c a7 c5 85 ...... Intel(R) PRO/1000 GT Desktop Adapter #2 - Teefer
2 Miniport
===========================================================================
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.42.161.112 192.42.161.220 1
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
192.42.160.0 255.255.255.0 192.42.160.220 192.42.160.220 20
192.42.160.220 255.255.255.255 127.0.0.1 127.0.0.1 20
192.42.160.255 255.255.255.255 192.42.160.220 192.42.160.220 20
192.42.161.0 255.255.255.0 192.42.161.220 192.42.161.220 20
192.42.161.220 255.255.255.255 127.0.0.1 127.0.0.1 20
192.42.161.255 255.255.255.255 192.42.161.220 192.42.161.220 20
192.42.162.0 255.255.255.0 192.42.162.220 192.42.162.220 20
192.42.162.220 255.255.255.255 127.0.0.1 127.0.0.1 20
192.42.162.255 255.255.255.255 192.42.162.220 192.42.162.220 20
224.0.0.0 240.0.0.0 192.42.160.220 192.42.160.220 20
224.0.0.0 240.0.0.0 192.42.161.220 192.42.161.220 20
224.0.0.0 240.0.0.0 192.42.162.220 192.42.162.220 20
255.255.255.255 255.255.255.255 192.42.160.220 192.42.160.220 1
255.255.255.255 255.255.255.255 192.42.161.220 192.42.161.220 1
255.255.255.255 255.255.255.255 192.42.162.220 192.42.162.220 1
Default Gateway: 192.42.161.112
===========================================================================
Persistent Routes:
None
Regards & Thanks
Mahesh

Routing and remote access logging to SQL server

Hi!
I am in the process of trying to set up SQL logging from routing and remote access on a windows server 2003 to another windows server 2003 which is running microsoft SQL server 2005.
What i did was i created a database named RRAS in the sql server and in routing and remote access i went under remote access logging and configured it, when i press "test connection" it says its successful. and when i check the local logfile i successfully
configured i can see my connection attempts towards the RRAS. but in the sql database there's nothing, no tables or anything.
I am sure i have the right permissions going on since i have only been using one account for everything so far(created the rras and the sql database), the SQL server is operational(it has a myriad of other databases that are used on a dailybasis).
So i am wondering what component is missing? do i need to create the tables manually, is there a guide that tells me how to do that?

Hi Plindgren,
Thanks for posting here.
May in know which fields we’ve created for this table ?
Please take look the link below and recheck the database settings:
Key concepts for IAS SQL Server logging
http://technet.microsoft.com/en-us/library/cc778830(WS.10).aspx
For more information please also refer to the link below:
Deploying SQL Server Logging with Windows Server 2003 Internet Authentication Service (IAS)
http://technet.microsoft.com/en-us/library/cc776712(WS.10).aspx
Thanks.
Tiger Li
Tiger Li
TechNet Community Support

Routing and Remote Access Server 2012 r2 Help

Hi all, I just setup a new 2012 R2 server with DHCP, DNS and Routing and Remote Access. When a user logs in to the VPN the DHCP is assigning the wrong IP address. My DHCP Scope is 10.0.10.100 to 10.0.10.199 but it's setting it to 169.254.X.X.
How do I fix this.

169.254.x.x are APIPA addresses which are allocated when the guest cannot see the DHCP server/allocator. Basically there is something wrong with your RRAS setup.
You should never run a remote access server on a DC. It will give you all sorts of name resolution problems. As soon as a client connects, the server acquires an additional IP for the VPN connection and the DC is multihomed. That has been a problem
since NT days and still is.
Bill

Routing and Remote access can cause cluster network issues?

After enabling routing and remote access on the servers, we found lots of cluster issues on our server like<o:p></o:p>
Cluster Service stopped
Communication was lost and reestablished between cluster nodes
Unable to access witness resource
Cluster resource failed
can RRAS enabling causes cluster network issues?
Rahul

Hi TwoR,
Please offer more information about your current cluster and RRAS configuration, such as are you installed the RRAS role on any cluster node? Are your cluster in Hyper-V environment?
Or if you want to create the RRAS cluster you can refer the following KB:
Deploy Remote Access in a Cluster
http://technet.microsoft.com/en-us/library/jj134175.aspx
How to configure Network Load Balancing (NLB) based cluster of VPN Servers
http://blogs.technet.com/b/rrasblog/archive/2009/07/02/configuring-network-load-balancing-nlb-cluster-of-vpn-servers.aspx
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

EA2700 and remote accessing DVR

Similar Messages

Maybe you are looking for