EA3500 in bridge/repeater mode - can't get it working!

Hi all,
I have a EA3500 as my primary wireless router. I have cable service and my EA3500's WAN port is connected to my cable modem. I have a few devices (NAS, etc) connected to LAN ports via Ethernet and other devices that connect wirelessly. With the single router, everything works fine.
My issues are when trying to add a second EA3500 to extend the range of my network. I've tried following Linksys' instructions on bridge mode as well as cascading (LAN to LAN).
No matter what I try, I can't get the second router to work properly. My main router is set to a LAN address of 192.168.11.1 and I am setting the second to 192.168.11.2. I am also setting the SSID and security settings the same on both routers. However, once the second router reboots I have devices connecting to it which are then unable to reach the Internet.
My end goal is to have the second router in a media room where my PlayStation, TV, and audio components will be able to connect to it and access both my NAS on the LAN and the Internet. Can anyone provide instructions on exactly how to set these things up? I'm about to throw both of these in the trash and start over with a different brand.
Thanks in advance!
Jim

Hello lootcorp,
Try checking the connections between the modem, 1st EA3500, and the 2nd EA3500. See which ethernet cables are connected from one port to another (from the modem to the 1st and 2nd router. Try changing ethernet cables if possible. To cascade the routers using LAN to LAN method, here's a link:
Cascading or Connecting a Linksys router to another router
Do not forget to reset the routers before you cascade them. I would opt for the LAN to WAN method of cascading. That way, you have 2 sets of wireless networks with different SSIDs and passwords.
Bonne Chance and keep us in the loop.

Similar Messages

WAP4410N Bridge/Repeater mode

Guys/Gals.
I have just been escalated to Level 3 support about my bridging issues.
Just a quick recap:
Bridge / Repeater mode configuration separated by 150 feet. Worked perfect for over 3 months.
Upgraded firmware due to lockups starting to happen, now cant get the bridge / repeater to work longer than 15 min.
After MANY support calls, new devices sent (version 2's) still no luck.
Today:
Talked to Marcelo at1 866 606 1866 and he stated that the Bridge / Repeater mode will not be supported farther than 50 Feet.
(seems like a cop out to me) He didn't seem to have an answer as to why it worked for 3 Months other than interference
Of which I have ran spectrum analyzers and see no Interference. Hell even 10 feet away I cant get the units to work longer than 15 min.
So I definitely think the 50 foot thing is a BS answer.
Also they have told me that External Antennas are not supported with these devices.
Again even though People 500 feet away connect just perfect (without a bridge / repeater mode) with 50% coverage!
so here I am (spent 600 bucks) on bricks.. and nobody will support the device and I cant seem to get my money back.
I have 8 customers with these devices, I am not going to use Cisco any longer. However will continue to fight this,
as we all seem to have the same BS issues.
Will keep you posted as he is talking to a developer about his answer to the antennas (external) and range.

Hi Kevin -- Have you attempted to return your devices to place of purchase or get RMA through the Small Business Support Center? Please provide an update on your issues.
Thanks,
Stephanie Reaves
Cisco Small Business Technology Group

TS1372 my ipod classic is in disk mode, can,t get out of it, it says error 1439, what can i do, i tried everything, they said in the apple page, please help me.

dear, Friends,
I have ipod classic, My ipod is in the disk mode, can't get out of it, it says error 1439, i had tried too many times, with trying to reset the ipod or restore it, but failed, please help me in this what can i do.

Try going to settings and reset all settings. This worked for me.

I lost my iphone 5 and it died. If i erased it in lost mode can i get my info on my phone and send it to another? or would it be lost? but if i find my phone can i recover it? can anyone even see the contents in my phone when its in lost mode?

If i erased it in lost mode can i get my info on my phone and send it to another? or would it be lost? but if i find my phone can i recover it? can anyone even see the contents in my phone when its in lost mode?

If you wiped it then the data is gone.
your only hope would be to get a new iphone and restore any backups made of the old phone to the new one.

I have 2 itunes accounts - one work a/c and one home a/c, but when i sign in at home only my home songs appear even if I sign in my work a/c. I have authorised both computers to show both a/cs. How can I get my work a/c songs to appear at home?

I have 2 itunes a/cs one at work and one at home. Both computers are authorised for the 2 a/cs, but I can;t get my work a/c songs to show on my home computer, even though I sign in my work a/c, and I can't get my home songs to show up on the work computer even though I sign in my home a/c. V. frustrating!

Hi,
You will have to manually copy your music. Get a pen-drive big enough to accommodate all your music. And follow these steps:
1. Create a new folder on the pen-drive.
2. Copy the music from your work computer to the folder you just created. It's in (yourhomefolder)>Music>iTunes>iTunes Media>Music if you're using a Mac, or in C:\Users\(yourusername)\Music\iTunes\iTunes Media\Music if you're using Windows.
3. Now on your home computer quit iTunes, and copy your music from work to the "Automatically Add to iTunes" folder in (yourhomefolder)>Music>iTunes>iTunes Media.
4. Start iTunes. It will automatically start to process the files and move them to the appropriate place.
Repeat these steps with your music from home on your work computer. Also I suggest to use only one iTunes account if possible.
Hope it helps
Regards,
Gábor

Can t get to work tint2 launcher

I'm a beginner in arch linux and i'm trying to figure out why the laucher don't show up in my panel,
i've set up the panel the way i want but i would like to have a few launcher
I've try serveral thing but i can't get it to work,
and chromium.desktop and gparted.desktop do exist in /usr/share/applications/
tks
Here my tint2rc
# TINT2 CONFIG FILE
# horizontal panel
# squared taskbars
# idirae config
# Background definitions
# ID 1
rounded = 0
border_width = 1
background_color = #808080 20
border_color = #ffffff 10
# ID 2 - task active
rounded = 0
border_width = 0
background_color = #feffff 0
border_color = #d8d8d8 0
# ID 3 - task
rounded = 0
border_width = 0
background_color = #F5F5DC 0
border_color = #000000 0
# ID 4
rounded = 0
border_width = 1
background_color = #888888 0
border_color = #ED2323 60
# ID 5 - taskbar
rounded = 0
border_width = 1
background_color = #feffff 10
border_color = #ffffff 10
# ID 6 - active taskbar
rounded = 0
border_width = 1
background_color = #feffff 30
border_color = #ffffff 30
# ID 7 - tooltip
rounded = 3
border_width = 0
background_color = #222222 90
border_color = #222222 90
# ID 8
rounded = 0
border_width = 1
background_color = #888888 20
border_color = #888888 20
# Panel
panel_monitor = all
panel_position = top left horizontal
panel_items = LTSBC
panel_size = 100% 32
panel_margin = 0 1
panel_padding = 3 3
panel_dock = 0
wm_menu = 1
panel_layer = bottom
panel_background_id = 1
# Panel Autohide
autohide = 0
autohide_show_timeout = 0.3
autohide_hide_timeout = 1.5
autohide_height = 6
strut_policy = follow_size
# Taskbar
taskbar_mode = multi_desktop
taskbar_padding = 5 2
taskbar_background_id = 5
taskbar_active_background_id = 6
taskbar_name = 1
taskbar_name_background_id = 0
taskbar_name_active_background_id = 0
taskbar_name_font = Crisp 12
taskbar_name_font_color = #ffffff 30
taskbar_name_active_font_color = #ffffff 50
# Tasks
urgent_nb_of_blink = 20
task_icon = 1
task_text = 0
task_centered = 1
task_maximum_size = 20 20
task_padding = 0 0
task_background_id = 3
task_active_background_id = 2
task_urgent_background_id = 4
task_iconified_background_id = 3
# Task Icons
task_icon_asb = 80 0 0
task_active_icon_asb = 100 0 0
task_urgent_icon_asb = 100 0 0
task_iconified_icon_asb = 80 0 0
# Fonts
task_font = BankGothic Md BT 10
task_font_color = #696969 60
task_active_font_color = #696969 100
task_urgent_font_color = #696969 100
task_iconified_font_color = #696969 60
font_shadow = 0
# Launcher
launcher_icon_theme = elementary
launcher_padding = 2 2
launcher_background_id = 1
launcher_icon_size = 20
# Specify icon theme names with launcher_icon_theme.
# if you have an XSETTINGS manager running (like xfsettingsd), tint2 will follow your current theme.
#launcher_icon_theme = AwOkenWhite
# Each launcher_item_app must be a full path to a .desktop file
launcher_item_app = /usr/share/applications/chromium.desktop
launcher_item_app = /usr/share/applications/gparted.desktop
# Clock
time1_timezone = :/usr/share/zoneinfo/dir/Canada/Eastern
time1_format = %I:%M %p
time1_font = BankGothic Md BT 9
#time2_format = %A, %B %d
#time2_font = Ubuntu-L 7
clock_font_color = #ffffff 80
clock_padding = 5 0
clock_background_id = 5
clock_lclick_command = gsimplecal
#lock_rclick_command =
# System Tray
systray = 1
systray_padding = 2
systray_sort = right2left
systray_background_id = 5
systray_icon_size = 20
systray_icon_asb = 100 0 0
# Tooltips
tooltip = 0
tooltip_padding = 2 2
tooltip_show_timeout = 0.0
tooltip_hide_timeout = 0.0
tooltip_background_id = 7
tooltip_font_color = #ff0000 100
tooltip_font = Roboto-Thin normal 9.0
# Mouse
mouse_middle = none
mouse_right = toggle
mouse_scroll_up = toggle
mouse_scroll_down = iconify
# Battery
battery = 1
battery_hide = never
battery_low_status = 10
battery_low_cmd = notify-send "battery low"
bat1_font = sans 8
bat2_font = sans 6
battery_font_color = #ffffff 80
battery_padding = 5 0
battery_background_id = 5
# End of config
Last edited by jolejo07 (2013-07-05 01:39:25)

I've try but can't get it working ether, i've download from Aur but when i'm trying to use the PKGBUILD with makepkg
it telling me
==> ERROR: Cannot find the fakeroot binary required for building as non-root user.
==> ERROR: Cannot find the strip binary required for object file stripping.
Last edited by jolejo07 (2013-07-05 01:45:21)

How can we get ADFSecurity work when used in OC4J, OID and OAM?

I am getting error in http server log "mod_oc4j: Response status=499 and reason=Oracle SSO, but failed to get mod_osso global context."
But I am not using Oracle SSO and my client doesn't want to use it either, I am using OAM SSO(CoreIDSSO) in my configuration. Please read the details below.
I am using ADFSecurity in an app that is protected by OAM. To migrate ADFSecurity permissions from
system-jazn-data.xml to OID, I used JAZNMigrationTool to populate OID with Grantees and Permissions. OAM gives login page, and authentication works fine.
But ADFSecurity is not working. ADFComponent Delete button is enabled even for roles that dont have permissions for the iterator delete.
- The app works fine when I use without OAM. ADF Security permissions work fine.
- The app works fine when used with OAM, but with ADFSecurity disabled (enforce=false).
- When I enforce ADFSecurity alongwith OAM, ADFSecurity is not working.
In the doc "Oracle Containers for J2EE Security Guide b28957", there is a mention of use of CoreIDPrincipal for permissions. Our OID Permissions entries show
LDAPRealmRole for attribute orcljaznprincipal. I am not sure if this could be the reason.
We have configured AccessServerSDK for the SOA instance and have policy for the urls in the policy manager. We have entries in orion-application.xml, orion-web.xml and system-jazn-data.xml as per the documentations.
How can we get ADFSecurity work when used with OID and OAM?

Have you been able to successfully integrate OAS with OAM & OID? We have similar requriement and so far we have not been able to get it working.
We have application specific roles which we map to OID roles using orion-application.xml.
Any pointers to achieve this would be greatly appreciated.
thanks,
Dipal

In disk utility, it shows that my external hard drive is somehow unmounted and I can't access it in finder or repair it in Disk Utility. How can I get this working without losing my important data?

In disk utility, it shows that my external hard drive is somehow unmounted and I can't access it in finder or repair it in Disk Utility. How can I get this working without losing my important data?
Thank you!

When you erased the disk did you select Mac OS Extended Journaled as the format option?

My hard drive crashed on my Imac 24" 2009, i put in a new hard drive 2TB and a SSD drive 240 GB and removed the opticdrive. What external DVD can I get to work with the IMac? The Apple super drive is not compatible.

My hard drive crashed on my Imac 24" 2009, I installed a new hard drive 2TB and a SSD drive 240 GB and removed the optical drive.
What external DVD can I get to work with the IMac? The Apple super drive is not compatible.

Virtually any DVD burner that can connect to your Mac will work. They start at $40 on Amazon.

Hello, I use MAC AIR OSX 10.6.8 and have Adobe CS2, that I was using 2 years ago on my older computer. I stopped using it because it would close down in the middle of work. Now I would like to reinstall it on the MacAir but I can not get it working. It te

Hello, I use MAC AIR OSX 10.6.8 and have Adobe CS2, that I was using 2 years ago on my older computer. I stopped using it because it would close down in the middle of work. Now I would like to reinstall it on the MacAir but I can not get it working. It tells Adobe doesnT support my System. But I can not update my old version or activate it. What can I do?

The mac you want to install photoshop cs2 on is running mac os x 10.6.8 Snow Leopard?
(photoshop cs2 won't run on intel macs with mac os x newer than snow leopard)
Did you ever have cs2 installed on this particular computer before?
If the problem is that you already installed cs2, but it won't activate, that's because adobe took the activation servers offline for some older adobe products such as cs2.
You'll need to use the non activation version of cs2 from here and the supplied serial number:
Activation server shut down for Creative Suite 2, Acrobat 7, and Macromedia products

Can't get Mail working properly

I just got my new MacPro this week, and it's really great except for I can't get Mail working right. I've set up my accounts and a few emails come through, though not many, and because it's been a week since I've been online, there should be many more than that. Also, I can't send any emails at all, no matter what I do. They will eventually go into my Sent box, but I've been sending them to myself to see if it's working, and they never come through. I spent an hour on the phone yesterday with the tech support for my ISP, and they told me that I'd have to talk to the Apple techs because they didn't have current info for *Mail 3.1*, the version I have, that the latest they had was for 2.something. So I called the Apple tech support and spent 2 hours on the phone with them, and they weren't able to help me get it going correctly either. It keeps giving me error messages such as Connection Failed, or Unable to Receive Mail, saying "there may be a problem with the mail server or network" and that "the connection to the server on ... port has timed out." I'm on DSL and am always online, so I know it's not the internet connection that's the problem. Can anybody give me some advice on what I should try? Any help will be gratefully appreciated!

Is your ISP Verizon, Demon, or Glocalnet, then it might be Apples biggest Leopard Bug in conjunction with these ISP:s POP-servers.
The one that randomly changes the settings in "advanced" from "password" to "APOP".
The visual result of this bug is that you will get a popup-box where Mail asks you to enter your password. (Which is useless entering, since the preference settings are changed.)
My advice counts only when you are supposed to use "password" as the correct setting in "Advanced" and in conjunction with some ISP:s.
Michael

Can't get webutil working on AS

Hi All,
As topic, I can't get webutil working on the application server. I can run individual forms or sessions that do not utilise webutil. As soon as I have baseHTMLjinitiator/baseHTMLjpi/baseHTML defined in the bit of the formsweb.cfg that I am using, I get this problem. The webutiljini.htm etc are located in the forms/server directory as they should be.
I've got it working fine on my 10.1.2 developer suite XP platform.
I've been trying without success on the App Server. Version 10.1.2 under Win2003
I have been right through the installation instructions several time trying to see what I have missed.
I have installed version 1.0.6 of webutil and version 1.8 of jacob.
I try and run the wu_test_106 form, and all I get is "Applet Started" at the bottom of the browser window, and a blank browser window.
My URL is
http://10.64.125.51:7778/forms/frmservlet?config=webutil1
The config in the formsweb.cfg is:
[webutil1]
WebUtilArchive=frmwebutil.jar,jacob.jar
WebUtilLogging=off
WebUtilLoggingDetail=normal
WebUtilErrorMode=Alert
WebUtilDispatchMonitorInterval=5
WebUtilTrustInternal=true
WebUtilMaxTransferSize=16384
baseHTMLjinitiator=webutiljini.htm
baseHTMLjpi=webutiljpi.htm
baseHTML=webutilbase.htm
archive_jini=frmall_jinit.jar
archive=frmall.jar
lookAndFeel=generic
form=wu_test_106.fmx
width=100%
height=100%
separateFrame=True
The other parameters are default. If I try a different form name it makes no difference.
I've done the other configuration stuff, default.env, signing jar files, etc.
The java console just shows:
Oracle JInitiator: Version 1.3.1.22
Using JRE version 1.3.1.22-internal Java HotSpot(TM) Client VM
User home directory = C:\Documents and Settings\griggto01
Proxy Configuration: Manual Configuration
Proxy:
Proxy Overrides:
JAR cache enabled
Location: C:\Documents and Settings\griggto01\Oracle Jar Cache
Maximum size: 50 MB
Compression level: 0
c: clear console window
f: finalize objects on finalization queue
g: garbage collect
h: display this help message
l: dump classloader list
m: print memory usage
q: hide console
s: dump system properties
t: dump thread list
x: clear classloader cache
0-5: set trace level to <n>
Loading http://10.64.125.51:7778/forms/java/frmwebutil.jar from JAR cache
RegisterWebUtil - Loading WebUtil Version 1.0.6
Thanks for your help.
Tony

Hi Tony,
Form your post it doesn't look like jacob.jar is being loaded. Can you confirm that you have the following files in the <ORACLE_AS>/forms directory:
java\
   jacob.jar
   frmwebutil.jar
webutil\
   d2kwut60.dll
   jacob.dllAlso open up your default.env file and check that
ORACLE_HOME         -- is correct
FORMS_PATH            -- has the path where wu_test_106.fmx is located
WEBUTIL_CONFIG      -- is correct (I've experienced what you describe when this path was invalid)
CLASSPATH             -- contains frmwebutil.jar
Regards
Tom Casserly

Can't get my work email to load on my new phone

I can't get my work email onto my Droid X. Anyone know the trick?

Carl3 wrote:
I can't get my work email onto my Droid X. Anyone know the trick?
First quesiton I have is do you have authorization to access your work email from your Droid X? Just knowing the email address and password is enough for you to get your personal email, but your employer must approve remote access.
If it's okay with your employer, you may also need to know the incoming and outgoing email server addresses, the port number, and your username on your employer's email server. If you're not sure what they are, check with your IT admin AFTER you get confirmation that it's okay to get your email.

Australia Post Shipping - Can't get to work

Hi,
I have read all the online support docs I can find and I just can't get Australia Post Shipping to work on our site for international orders.
Everywhere it says:
Choose your shipping provider
Enter your account details
Your customers see real time shipping costs!
But Australia Post selection doesn't let us enter account details - does anyone know where I enter them?
(see image at bottom)
And after I allocated sizing, weights etc to every product it doesn't even look like it even works:
(see how there are no options to select)
Does anyone have any ideas on how to get it to actually work? I can't imagine BC would role something like this out if it didn't even work but from all my googling I can't see that anyone actually uses it (or at least comments on using it!)
Would love any help

I've try but can't get it working ether, i've download from Aur but when i'm trying to use the PKGBUILD with makepkg
it telling me
==> ERROR: Cannot find the fakeroot binary required for building as non-root user.
==> ERROR: Cannot find the strip binary required for object file stripping.
Last edited by jolejo07 (2013-07-05 01:45:21)

My iMessage and FaceTime doesn't work. how can i get it working?

my iMessage and FaceTime doesn't work. how can i get it working?

Without more information such as:
- what happens when your try?
- DId it work before and other things
all I can suggest is:
iOS: Troubleshooting FaceTime
iOS: Troubleshooting Messages

EA3500 in bridge/repeater mode - can't get it working!

Similar Messages

Maybe you are looking for