EA4500 FTP timeout
Hi people,
I'm having this problem with my Linksys EA4500 and the FTP use.
I connected a WD 1TB hard drive, and created the FTP which works great.
When I'm at my parents, of work I can access folders, and copy files.
But When the files get larger, the copy function will give me a time out.
I guess due to inactivity, even while the file is still copying.
Does anybody know a solution to this? Does the FTP function have a time out set, that I can change like Windows server FTP?
Windows server FTP also has the same problem. Default the time out is set to 30 minutes. But you can change it. And for the router I can't seem to find any option to change the time out?
I hope someone can help me!
When transferring files ftp there is no time out during the transfer.
You are getting disconnected for extended periods during a transfer that is causing the failures.
Usually this is due to low or noisy wireless signal. To test try using ethernet connection for comparison.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support
Similar Messages
-
While processing a file with about 2000 messages from a Sender file channel which lasts about 35 minutes we receive an error which points to a time-out parameter:
"Error file:'nnnn': Archiving to file 'nnnn' on FTP server after processing failed with com.sap.aii.adapter.file.FTPEx: Timeout (900 seconds): closing control connection."
Did anyone come across this problem or knows where this parameter is located.
Thanks for your comments.
PeterHi Peter
In your file/ftp adapter configuration, check on 'Advanced Mode'. There you add the entry,
Name : ftp.timeout
Value : timeoutsecs
cheers
Sameer
PS: Also check OSS note 849089 -
Difference between timeout(secs) and advanced parameter ftp.timeout
Hi experts,
I have one question:
in sender communication channel, is the same to specify timeout(secs) in FTP connection parameters or to specify ftp.timeout parameter in advanced mode tab?
This is order to solve the problem of "ftp stops polling" solved with below SAP note 1083488.
Thanks
Fabio
Symptom
Sometimes, some of the XI FTP/JDBC sender channels stopped polling
permanently. However this is resolved by re-starting these channels.
Other terms
FTP sender channels, JDBC sender channels, polling stopped, stopped
polling, polling adapters.
Reason and Prerequisites
Program Error
Solution
For FTP adapter, please set the appropriate FTP timeout parameter in sender
channel configurations. Existing timeout implementation has a bug while
reading from Input. This patch solves this problem.
Edited by: Fabio Boni on May 18, 2011 5:16 PMHello!
If you don't have the patches mentioned on the note, you must use the advanced tab parameter. Otherwise, you can specify it in the FTP Connection parameters tab. -
hey guys,
i have another issue with leopard server ftp service. users get a timeout and cannot upload files to the end. especially bigger size files.
did you guys ever had/have this problem?
called apple:) that was the funny part:) after waiting about 40 minutes, i got to a guy who is supposed to know something about the leopard server. he had no answer, he just recommended to try out third party software, what i will do as i have no other solution.
i think it is a great shame. no offence, but our company payed a good amount for the xserve. it is frustrating.
any ideas?There has been several threads on this subject over the last few weeks and it seems to come down to two points. The FTP server in 10.5 lets anyone that is authorized see all folders, if you don't care about that, but you want them to start off in a specific directory all they need do is add that directory to the ULR, or on specific FTP clients name the start directory. If you want it so users can't see anything other than their own directory you might be better off looking at a stand alone FTP server. What I find unhelpful about this solution is that you have to build a new set of users and groups, which I think defeats the object of running the server in first place. I hope this is something apple will address soon.
-
Environment - NW 6.5 SP5 eDir 8.7.3.9 with BM 3.8 SP5.
We are trying to download a document from the following site:
ftp://leginfo.public.ca.gov/pub/dail...ar_Session.pdf
We created a general exception in the Firewall for all IPs on our network (we own a Class C range) as follows:
Source Interface: Private
Destination Interface: Public
Packet Type: ftp-pasv-st
Protocol: TCP
Src Port: <All>
Dest Port: 21
Stateful Filtering: Enabled FTP(PASV)
Src Address: Network XXX.XXX.0.0/255.255.0.0
Dest Address: Any Address
When we try to access the file, we get the following error:
Status : 504 Gateway Time-Out
Description : Unable to connect to origin Web server.
Note : If necessary, please contact your Systems Administrator for resolution
Yet when I try from the outside, no problem.
Any Ideas????This is very strange. When I downed the filters, no problems. When I reloaded the filters no problem. When I unloaded proxy and did a proxy -cc reload, now the link wont open the file.
However, if I enter the following URL:
ftp://leginfo.public.ca.gov/pub/dailyfile/asm/
I can see the files and I can even copy the files to my PC. But if I try to double click on the file, I get the:
Status : 504 Gateway Time-Out
Description : Unable to connect to origin Web server.
Note : If necessary, please contact your Systems Administrator for resolution
error. After I've unloaded Filtsrv and downloaded the file, I'm able to open it again when the Filtsrv reloaded. I've even cleared my cache and deleted offline files. However, if I go to the URL:
ftp://leginfo.public.ca.gov/pub/dailyfile/asm/
and try to open the other PDF file that is there, I get the:
Status : 504 Gateway Time-Out
Description : Unable to connect to origin Web server.
Note : If necessary, please contact your Systems Administrator for resolution
error. -
Ea4500 FTP server - connects but that's it..
Have a security camera that will ftppics but when I enter ftpserver login it can't save.
So, everything is on the same 192 network. My pc client connects to the ftpserver fine but will not get a directory list, save a txt file, or do anything other than connect. My account has read/write and I don't get it..
Solved!
Go to Solution.Also don't disconnect the usb drive while the router is on unless you use the Safely Remove Disk feature.
Create the share using the router utility.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support -
How does TimeOut(Sec) works/ behave in FTP Adapter?
Hi ,
How does TimeOut(Sec) works/ behave in FTP Adapter?
Lets Say : If I mention 300 Secs in this . How Should it behave ??
if a file processing in adapter is taking more then 300 sec , will it also be terminated ??? what error response i will get in such case.
Regards
Prabhat Sharma.Hi,
if there's a network error the channel may hang (for a very long time)
if you specify 300 secs after that time the channel will reset the connection and you can start pooling again
for more details:
Note 849089 - XI 3.0 / PI 7.0 File Adapter: FTP Timeout Handling
Regards,
Michal Krawczyk -
Receiver File Adapter: FTPS Error
On sending a text file to a trading partner the log in the communication channel shows the following:
Connecting to FTP server - success
Write to FTP server - success
Transfer: "TXT" mode - success
Exception caught by adapter framework:connection timed out - Error
The FTP connection Parameters have:
Data connection = Passive
Connection security = FTPS (FTP using SSL/TLS)
Command order AUTH TLS, USER, PASS, PBSZ, PROT
Use of X509 cert for Client Authentication is checked
Keystore = service_ssl
x.509 Cert and private key = *******.crt
When I look in the NWA logs for default trace I see several messages with the text "Rolling back transaction for message..." plus a FILE_ERR_211
What is a FILE_ERR_211?
Thanks
Markhi mark,
To configure a timeout for the FTP connection, please enable the "Advanced Mode" for the respective FTP communication channel in the Integration Directory and add an entry "ftp.timeout"=timeoutSecs
(without any quotation marks) to the "Additional Parameters" section, where timeoutSecs is the desired FTP timeout in seconds.
regards
kummari -
Mainframe Integration using File Adapter (FTP Mode):: ftp commands
Hi,
We are trying to integrate with Mainframe system using File Adapter. (FTP mode). We are able to write the file to Mainframe system but not able to format it properly. We had to provide FTP parameter, <b>ftp.quote site recfm=fb lrecl=150</b>
As per SAP Note 801926 :: XI 3.0 File Adapter: Additional Parameters, the only parameter that can be used is <b>ftp.timeout</b>. Has anyone tried out using other FTP parameters? (like ftp.quote)
Any help is grealy appreciated.
Regards,
Siva MarananiI am looking at running some OS commands especially the QUOTE SITE FILENAME, and found this OSS note:
https://service.sap.com/sap/support/notes/841704
In this note it says...
"Note that for the File Adapter transport protocol "FTP", the operating system command is NOT executed on the FTP server, but on the server hosting the Adapter Engine." -
IDOC to FTPs performance issue
Hello everyone,
I have a scenario BS_A:idoc > xi > BS_B: file via ftps (ftp over ssl/tcp).
For each idoc two different files (content conversion) are created in the same directory.
I therefore have one receiver determination and one interface intermination with 2 inbound interfaces + interface mappings + 2 file receiver adpapters.
I have a performance problem when more than one idocs are created at the same time. First message goes through very fast. The ones after that take there time.
It takes 10 to 30 minutes (and some times more) for 2 idocs to deliver successfully 4 files at the other side.
Note 1: I do not exprience this when i work with normal FTP.
Note 2: I have unchecked the "Maintain at order time" check box in the interface determination. If checked then the QoS is set to EOIO.
Thanks in advance for any input or suggestions.
Dimitris HagigeorgiouHi ,
see the below links
FTP Problem
http://help.sap.com/saphelp_nw04/helpdata/en/e3/94007075cae04f930cc4c034e411e1/frameset.htm
FTP Error
File Adapter FTP Timeout
FTP error Socket connection timed out:
Check if FTP is reachable? (like CMD > FTP > open?)
Secure FTP using FTPS (SSL/TLS) - need help!
Customize "Connection Timed Out" - Error Page
Regards
Chilla -
Dreamweaver FTP still doesn't work
So I've been trying to get FTP to work in (Mac) Dreamweaver
-- and I've tried every version since MX 2004. But they all fail.
This problem has been posted in this forum (and many others) in the
past. Whenever you try to connect/test an FTP server, you
immediately get this exact error:
"An FTP error occurred -- cannot make connection to host."
This error happens instantly. There is nothing to see in the
FTP log. It is not related to any FTP timeouts, firewall settings,
etc. I have stayed at Dreamweaver MX 2004 because it's FTP works
(and continues to work). Every version of Dreamweaver I've tried
since then, CS, CS 2, CS 3, etc. all give this same error. I've
tried deleting ssh_hosts. I've deleted keychains. I've tried
reinstalling. I've deleted preferences. Rebuild site caches. I've
tried different servers, hosts, etc. FTP (with and without all the
Passive, etc. options, SFTP, etc. I've tested FTP/SFTP in other
programs, in the Terminal etc. I've turned off Firewalls, removed
routers, etc. What am I missing?
Why is Dreamweaver MX 2004 the last version able to perform
FTP operations on our Mac?Thanks. For what it's worth, I cannot connect to that gov
site in CS4
either. I'm checking to see if there's any info available for
this
problem....
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"jca1138" <[email protected]> wrote in
message
news:gqqm4f$glj$[email protected]..
>
quote:
Originally posted by:
Newsgroup User
> Tell me what you have in the Remote site definition
fields for a site that
> doesn't work, please.
>
> I created a new site in both Dreamweaver 2004 MX and
Dreamweaver CS 3 with
> these same settings for testing/comparison:
>
> ----------------
> Access type: FTP
> FTP host: ftp.irs.gov
> Host directory:
> Login: anonymous
> Password:
>
> [X] Use passive FTP
> ----------------
>
> In Dreamweaver 2004 MX, clicking the "Test" button gives
this message:
>
> "Dreamweaver connected to your server successfully."
>
> In Dreamweaver CS 3, clicking the "Test" button gives
this message:
>
> "An FTP error occurred - cannot make connection to
host."
>
> (Saving the site and trying to connect via the
Files/Site pane produces
> the
> same results.)
>
> As I mentioned in the previous post, this problem
doesn't change when
> trying
> different settings.
>
> To answer the original poster, the reason I'm using
ftp.irs.gov as an
> example
> is it is a public/anonymous FTP server people often use
to test making FTP
> connections, and is even mentioned by adobe:
>
>
http://kb.adobe.com/selfservice/viewContent.do?externalId=tn_14834
> -
Connection timed out error in ftp adapters
Hi All,
I have integrated two ftp servers by using FTP adapter as sender and receiver.
But the process is not started as it is giving the error ConnectException:Connection timed out.
I applied the note 849089.(ftp.timeout=timeoutSecs) here i have given the value 60 ,but still it is giving the same error.
Please suggest me in this regard.
Thanks in advance.
Prasad NemalikantiHi,
Check the server details and the user credentials for the ftp server you are using and check whether you have provided the correct path in the ftp server.
Also try to login to the ftp server which you have mentioned in CC using the user name and pwd, to chk whether you have the permissions to login to the server.
Also the check whether the folder you are trying to access is having permission for delete/read/write.
Regards,
Nithiyanandam -
NAT overload is not working when i configure Double NAT for VPN
I have Cisco 2921 router with OS version 15.1(4)M1.
the router is configured for NAT overload and working fine, i have site to site VPN tunnel with peer with normal NAT translation. now we need to configure Double NAT on the VPN tunnel as we need to free the subnet on peer network. for double nat i use 3.2.21.x - 3.2.23.x / 24 network and apply following command
Double NAT translation
ip nat inside source static network 192.168.10.0 3.2.21.0 /24 no-alias
ip nat inside source static network 192.168.20.0 3.2.22.0/24 no-alias
ip nat inside source static network 192.168.30.0 3.2.23.0 /24 no-alias
Nonat
access-list 101 deny ip 3.2.21.0 0.0.0.255 3.2.1.0 0.0.0.255
access-list 101 deny ip 3.2.22.0 0.0.0.255 3.2.1.0 0.0.0.255
access-list 101 deny ip 3.2.23.0 0.0.0.255 3.2.1.0 0.0.0.255
VPN encrypted traffic over the tunnel
access-list 115 permit ip 3.2.21.0 0.0.0.255 3.2.1.0 0.0.0.255
access-list 115 permit ip 3.2.22.0 0.0.0.255 3.2.1.0 0.0.0.255
access-list 115 permit ip 3.2.23.0 0.0.0.255 3.2.1.0 0.0.0.255
Problem:
as soon as i apply Double NAT translation command the NAT overload stop working and client cannot reach to the internet
the router partial configuration is as below
REACH-R01(config)#do sh run
Building configuration...
Current configuration : 19233 bytes
! Last configuration change at 09:56:45 MST Tue Jan 29 2013 by admin
! NVRAM config last updated at 13:57:54 MST Wed Jan 30 2013
! NVRAM config last updated at 13:57:54 MST Wed Jan 30 2013
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname REACH-R01
boot-start-marker
boot-end-marker
card type t1 0 0
logging buffered 51200 warnings
no aaa new-model
clock timezone MST -7 0
clock summer-time MST recurring
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
no ipv6 cef
ip source-route
ip cef
ip dhcp excluded-address 192.168.20.1 192.168.20.99
ip dhcp excluded-address 192.168.20.250 192.168.20.255
ip dhcp pool CISCO_PHONES
network 192.168.20.0 255.255.255.0
default-router 192.168.20.254
option 150 ip 192.168.20.254
no ip domain lookup
ip domain name reach.local
ip inspect name ethernetin ftp timeout 3600
ip inspect name ethernetin h323 timeout 3600
ip inspect name ethernetin http timeout 3600
ip inspect name ethernetin rcmd timeout 3600
ip inspect name ethernetin realaudio timeout 3600
ip inspect name ethernetin smtp timeout 3600
ip inspect name ethernetin sqlnet timeout 3600
ip inspect name ethernetin streamworks timeout 3600
ip inspect name ethernetin tcp timeout 3600
ip inspect name ethernetin tftp timeout 30
ip inspect name ethernetin udp timeout 15
ip inspect name ethernetin vdolive timeout 3600
multilink bundle-name authenticated
isdn switch-type primary-ni
trunk group PRI
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-3180627716
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3180627716
revocation-check none
rsakeypair TP-self-signed-3180627716
voice-card 0
dsp services dspfarm
voice service voip
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
sip
voice translation-rule 1
rule 5 /^7804981231/ /401/
voice translation-rule 2
rule 5 // /7804981231/
voice translation-profile DID_INBOUND
translate called 1
voice translation-profile DID_OUTBOUND
translate calling 2
license udi pid CISCO2911/K9 sn FGL1540114P
license accept end user agreement
license boot module c2900 technology-package securityk9
hw-module ism 0
hw-module pvdm 0/0
username test test
redundancy
controller T1 0/0/0
cablelength long 0db
pri-group timeslots 1-6,24
no ip ftp passive
crypto isakmp policy 10
encr aes 256
authentication pre-share
group 2
crypto isakmp key P@ssw0rd address 33.33.33.33 no-xauth
crypto ipsec transform-set ESP-AES256-SHA esp-aes 256 esp-sha-hmac
crypto map VPN-TUNNEL 1 ipsec-isakmp
description COMPUGEN
set peer 33.33.33.33
set transform-set ESP-AES256-SHA
match address 115
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description Outside Interface To the Internet
ip address dhcp
ip access-group outside_access_in in
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map VPN-TUNNEL
interface ISM0/0
ip unnumbered GigabitEthernet0/1.20
service-module ip address 192.168.20.2 255.255.255.0
!Application: CUE Running on ISM
service-module ip default-gateway 192.168.20.254
interface GigabitEthernet0/1
no ip address
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/1.10
description VLAN 10 DATA VLAN
encapsulation dot1Q 10
ip address 192.168.10.254 255.255.255.0
ip nat inside
ip inspect ethernetin in
ip virtual-reassembly in
interface GigabitEthernet0/1.20
description VLAN 20 VOICE VLAN
encapsulation dot1Q 20
ip address 192.168.20.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.30
description VLAN 30 WIRELESS VLAN
encapsulation dot1Q 30
ip address 192.168.30.254 255.255.255.0
ip nat inside
ip inspect ethernetin in
ip virtual-reassembly in
interface GigabitEthernet0/2
no ip address
shutdown
duplex auto
speed auto
interface ISM0/1
description Internal switch interface connected to Internal Service Module
no ip address
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
trunk-group PRI
no cdp enable
interface Vlan1
no ip address
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip http path flash:CME8.6/GUI
ip nat inside source static tcp 192.168.10.10 443 interface GigabitEthernet0/0 443
ip nat inside source static tcp 192.168.10.10 25 interface GigabitEthernet0/0 25
ip nat inside source static tcp 192.168.10.10 1723 interface GigabitEthernet0/0 1723
ip nat inside source static tcp 192.168.10.10 3389 interface GigabitEthernet0/0 3389
ip nat inside source static tcp 192.168.10.10 123 interface GigabitEthernet0/0 123
ip nat inside source static tcp 192.168.10.10 987 interface GigabitEthernet0/0 987
ip nat inside source list 101 interface GigabitEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/0 75.152.248.1
ip route 0.0.0.0 0.0.0.0 75.152.248.1 254
ip route 0.0.0.0 0.0.0.0 205.206.0.1 254
ip route 192.168.20.2 255.255.255.255 ISM0/0
ip access-list extended outside_access_in
permit udp any any eq bootps
permit udp any any eq bootpc
permit tcp any host 22.22.22.22 eq 1723
permit tcp any host 22.22.22.22 eq 3389
permit tcp any host 22.22.22.22 eq smtp
permit tcp any host 22.22.22.22 eq 443
permit tcp any host 22.22.22.22 eq domain
permit udp any host 22.22.22.22 eq domain
permit tcp any host 22.22.22.22 eq 123
permit icmp any host 22.22.22.22 unreachable
permit icmp any host 22.22.22.22 echo-reply
permit icmp any host 22.22.22.22 packet-too-big
permit icmp any host 22.22.22.22 time-exceeded
permit icmp any host 22.22.22.22 traceroute
permit icmp any host 22.22.22.22 administratively-prohibited
permit icmp any host 22.22.22.22 echo
permit tcp any host 22.22.22.22 eq 987
permit tcp any host 22.22.22.22 eq 47
permit gre any host 22.22.22.22
permit udp any host 22.22.22.22 eq isakmp
permit esp any host 22.22.22.22
access-list 23 permit any
access-list 101 deny ip 192.168.20.0 0.0.0.255 3.2.1.0 0.0.0.255
access-list 101 deny ip 192.168.30.0 0.0.0.255 3.2.1.0 0.0.0.255
access-list 101 deny ip 192.168.10.0 0.0.0.255 3.2.1.0 0.0.0.255
access-list 101 deny ip 3.2.21.0 0.0.0.255 3.2.1.0 0.0.0.255
access-list 101 deny ip 3.2.22.0 0.0.0.255 3.2.1.0 0.0.0.255
access-list 101 deny ip 3.2.23.0 0.0.0.255 3.2.1.0 0.0.0.255
access-list 101 permit ip 192.168.10.0 0.0.0.255 any
access-list 101 permit ip 192.168.20.0 0.0.0.255 any
access-list 101 permit ip 192.168.30.0 0.0.0.255 any
access-list 110 permit ip 0.0.0.0 255.255.255.0 0.0.0.0 255.255.255.0
access-list 115 permit ip 3.2.21.0 0.0.0.255 3.2.1.0 0.0.0.255
access-list 115 permit ip 3.2.22.0 0.0.0.255 3.2.1.0 0.0.0.255
access-list 115 permit ip 3.2.23.0 0.0.0.255 3.2.1.0 0.0.0.255
Solution: Support forums teamI have the same problem also. Restarting isn't helping and the auto lock/unlock button is on. Plus a couple of time when I turn it on it is asking if I want to power off. That is when I push the button on the front to wake it up. Not the power button on top. I have an IPAd 2. Worked fine before the update.
-
MTU Size Problem Loading Certain Webpages
Hello Colleagues,
I'm having a strange problem dealing with MTU sizes and loading certain webpages. I am aware of the default Microsoft MTU of 1500 and also using GRE IPSEC Tunnels recommended at MTU size 1400. I have since manually set some users PC's to MTU of 1400 and most of those users are experiencing no issues. However, there are a few users who still experience website loading issues even though I have manually changed their MTU size to 1400.
These are domain accounts will the same image loads on their machines, so all have the same permissions, rights, firewall settings, etc. They all use the same LAN, switches, and routers.
Here are the router configs, router 1 and router 2
Router 1
Current configuration : 9006 bytes
version 15.3
no service pad
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
service password-encryption
hostname R-US-RS-WVPN1
boot-start-marker
boot system flash:c1900-universalk9-mz.SPA.153-1.T1.bin
boot system flash:c1900-universalk9-mz.SPA.151-3.T1.bin
boot-end-marker
logging buffered 64000
enable secret 5 *removed*
no aaa new-model
clock timezone CET 1 0
clock summer-time CET recurring last Sun Mar 2:00 last Sun Oct 3:00
errdisable recovery cause udld
errdisable recovery cause bpduguard
errdisable recovery cause rootguard
errdisable recovery cause pagp-flap
errdisable recovery cause dtp-flap
errdisable recovery cause link-flap
errdisable recovery interval 303
ip cef
ip domain name corp.com
ip name-server 10.###.8.21
ip name-server 10.###.8.96
ip inspect dns-timeout 90
ip inspect tcp idle-time 60
ip inspect name fw smtp timeout 120
ip inspect name fw ftp timeout 120
ip inspect name fw realaudio
ip inspect name fw tftp timeout 30
ip inspect name fw udp timeout 30
ip inspect name fw tcp timeout 60
no ipv6 cef
multilink bundle-name authenticated
crypto pki trustpoint TP-self-signed-316595902
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-316595902
revocation-check none
rsakeypair TP-self-signed-316595902
crypto pki certificate chain TP-self-signed-316595902
certificate self-signed 01
*removed*
quit
license udi pid CISCO1921/K9 sn FTX153182M8
spanning-tree vlan 229 priority 8192
redundancy
ip ssh version 2
crypto isakmp policy 10
hash md5
authentication pre-share
lifetime 3600
crypto isakmp key *removed* address 70.###.172.142
crypto isakmp key *removed* address 184.###.###.254
crypto isakmp keepalive 35 11
crypto ipsec transform-set FY-WVPN-Tunnel esp-aes esp-md5-hmac
mode tunnel
crypto map vpn 10 ipsec-isakmp
set peer 70.###.172.142
set peer 184.###.###.254
set transform-set FY-WVPN-Tunnel
match address gre-tunnel-list
interface Loopback0
ip address 10.###.0.10 255.255.255.255
interface Tunnel2291
description Primary-TimewarnerTelecom-Ral-FayWVPN1
ip address 10.###.99.26 255.255.255.252
no ip redirects
cdp enable
tunnel source 66.###.161.126
tunnel destination 184.###.###.254
crypto map vpn
interface Tunnel2293
description Primary-TimewarnerTelecom-Ral-FayWVPN2
ip address 10.###.99.154 255.255.255.252
no ip redirects
cdp enable
tunnel source 66.###.161.126
tunnel destination 70.###.172.142
crypto map vpn
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description TW Telecom/DMVPN1
ip address 66.###.161.126 255.255.255.252
ip access-group Block-Internet in
ip access-group Block-Internet out
duplex auto
speed auto
no cdp enable
crypto map vpn
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
interface GigabitEthernet0/0/0
switchport access vlan 229
no ip address
interface GigabitEthernet0/0/1
switchport access vlan 229
no ip address
interface GigabitEthernet0/0/2
switchport access vlan 229
no ip address
interface GigabitEthernet0/0/3
description PBX Eth1
switchport access vlan 229
no ip address
interface Vlan1
no ip address
shutdown
interface Vlan229
ip address 10.###.229.253 255.255.255.0
ip helper-address 10.###.231.201
standby 229 ip 10.###.229.254
standby 229 priority 105
standby 229 preempt
router eigrp 100
network 10.0.0.0
ip forward-protocol nd
no ip http server
ip http secure-server
ip route 70.###.172.142 255.255.255.255 66.###.161.125
ip route 184.###.###.254 255.255.255.255 66.###.161.125
ip route 205.###.96.180 255.255.255.252 66.###.161.125
ip access-list extended Block-Internet
permit esp host 66.###.161.126 host 184.###.###.254
permit esp host 184.###.###.254 host 66.###.161.126
permit udp host 66.###.161.126 host 184.###.###.254 eq isakmp
permit udp host 184.###.###.254 host 66.###.161.126 eq isakmp
permit esp host 66.###.161.126 host 70.###.172.142
permit esp host 70.###.172.142 host 66.###.161.126
permit udp host 66.###.161.126 host 70.###.172.142 eq isakmp
permit udp host 70.###.172.142 host 66.###.161.126 eq isakmp
permit icmp host 66.###.161.126 host 184.###.###.254
permit icmp host 184.###.###.254 host 66.###.161.126
permit icmp host 66.###.161.126 host 70.###.172.142
permit icmp host 70.###.172.142 host 66.###.161.126
permit icmp any any echo-reply
permit icmp any any time-exceeded
permit icmp any any packet-too-big
permit icmp any any traceroute
permit icmp any any unreachable
deny ip any any
deny icmp any any
ip access-list extended gre-tunnel-list
permit gre host 66.###.161.126 host 184.###.###.254
permit gre host 66.###.161.126 host 70.###.172.142
logging host 10.100.###.254
logging host 10.100.###.246
snmp-server community a RW 20
snmp-server community r RO 20
snmp-server community a RW 20
snmp-server community r RO 20
snmp-server community P_RW RW
snmp-server community P_RO RO
snmp-server enable traps entity-sensor threshold
snmp-server host 10.100.###.246 public
snmp-server host 10.100.###.254 public
access-list 20 permit 10.###.9.3
access-list 20 permit 10.###.8.16
access-list 20 permit 10.100.###.249
access-list 20 permit 10.100.###.254
access-list 20 permit 10.100.###.246
control-plane
banner motd ^CCCCCCC
****************** Warning! Warning! Warning! ********************
This system is restricted to authorized users for business
purposes. Unauthorized access is a violation of the law. This
service may be monitored for administrative and security reasons.
By proceeding, you consent to this monitoring
****************** Warning! Warning! Warning! ********************
^C
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
exec-timeout 60 0
password 7 *removed*
login local
transport input ssh
line vty 5 15
exec-timeout 60 0
password 7 *removed*
login local
transport input ssh
scheduler allocate 20000 1000
ntp server 10.###.8.8 prefer
ntp server 10.###.231.200 prefer
ntp server 10.###.8.69
ntp server 10.###.1.6 prefer
end
Router 2
Current configuration : 9013 bytes
version 15.3
no service pad
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
service password-encryption
hostname R-US-RS-WVPN2
boot-start-marker
boot system flash:c1900-universalk9-mz.SPA.153-1.T1.bin
boot system flash:c1900-universalk9-mz.SPA.151-3.T1.bin
boot-end-marker
logging buffered 64000
logging console critical
enable secret 5 *removed*
no aaa new-model
clock timezone CET 1 0
clock summer-time CET recurring last Sun Mar 2:00 last Sun Oct 3:00
errdisable recovery cause udld
errdisable recovery cause bpduguard
errdisable recovery cause rootguard
errdisable recovery cause pagp-flap
errdisable recovery cause dtp-flap
errdisable recovery cause link-flap
errdisable recovery interval 303
ip cef
ip domain name corp.mann-hummel.com
ip name-server 10.###.8.21
ip name-server 10.###.8.96
ip inspect dns-timeout 90
ip inspect tcp idle-time 60
ip inspect name fw smtp timeout 120
ip inspect name fw ftp timeout 120
ip inspect name fw realaudio
ip inspect name fw tftp timeout 30
ip inspect name fw udp timeout 30
ip inspect name fw tcp timeout 60
ipv6 multicast rpf use-bgp
no ipv6 cef
multilink bundle-name authenticated
crypto pki trustpoint TP-self-signed-3179596086
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3179596086
revocation-check none
rsakeypair TP-self-signed-3179596086
crypto pki certificate chain TP-self-signed-3179596086
certificate self-signed 01
*removed*
quit
license udi pid CISCO1921/K9 sn FTX153182M2
spanning-tree vlan 229 priority 1###84
redundancy
ip ssh version 2
crypto isakmp policy 10
hash md5
authentication pre-share
lifetime 3600
crypto isakmp key *removed* address 70.###.172.142
crypto isakmp key *removed* address 184.###.###.254
crypto isakmp keepalive 35 11
crypto ipsec transform-set Fay-Ral-WVPN-Tunnel esp-aes esp-md5-hmac
mode tunnel
crypto map vpn 10 ipsec-isakmp
set peer 184.###.###.254
set peer 70.###.172.142
set transform-set Fay-Ral-WVPN-Tunnel
match address gre-tunnel-list
interface Loopback0
ip address 10.###.0.12 255.255.255.255
interface Tunnel2292
description Failover-TimewarnerCable-Ral-Fay-WVPN2
ip address 10.###.99.30 255.255.255.252
no ip redirects
cdp enable
tunnel source 96.###.25.226
tunnel destination 184.###.###.254
crypto map vpn
interface Tunnel2294
description Failover-TimewarnerCable-Ral-Fay-WVPN2
ip address 10.###.99.158 255.255.255.252
no ip redirects
cdp enable
tunnel source 96.###.25.226
tunnel destination 70.###.172.142
crypto map vpn
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description Fay-Ral WVPN
ip address 96.###.25.226 255.255.255.252
ip access-group Block-Internet in
ip access-group Block-Internet out
duplex auto
speed auto
no cdp enable
crypto map vpn
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/0/0
switchport access vlan 229
no ip address
interface GigabitEthernet0/0/1
switchport access vlan 229
no ip address
interface GigabitEthernet0/0/2
switchport access vlan 229
no ip address
interface GigabitEthernet0/0/3
description PBX Eth2
switchport access vlan 229
no ip address
interface Vlan1
no ip address
shutdown
interface Vlan229
ip address 10.###.229.252 255.255.255.0
ip helper-address 10.###.231.201
standby 229 ip 10.###.229.254
standby 229 preempt
router eigrp 100
network 10.0.0.0
ip forward-protocol nd
no ip http server
ip http secure-server
ip route 70.###.172.142 255.255.255.255 96.###.25.225
ip route 184.###.###.254 255.255.255.255 96.###.25.225
ip route 205.###.96.180 255.255.255.252 66.###.161.125
ip access-list extended Block-Internet
permit esp host 96.###.25.226 host 184.###.###.254
permit esp host 184.###.###.254 host 96.###.25.226
permit udp host 96.###.25.226 host 184.###.###.254 eq isakmp
permit udp host 184.###.###.254 host 96.###.25.226 eq isakmp
permit esp host 96.###.25.226 host 70.###.172.142
permit esp host 70.###.172.142 host 96.###.25.226
permit udp host 96.###.25.226 host 70.###.172.142 eq isakmp
permit udp host 70.###.172.142 host 96.###.25.226 eq isakmp
permit icmp host 96.###.25.226 host 184.###.###.254
permit icmp host 184.###.###.254 host 96.###.25.226
permit icmp host 96.###.25.226 host 70.###.172.142
permit icmp host 70.###.172.142 host 96.###.25.226
permit icmp any any echo-reply
permit icmp any any time-exceeded
permit icmp any any packet-too-big
permit icmp any any traceroute
permit icmp any any unreachable
deny ip any any
deny icmp any any
ip access-list extended gre-tunnel-list
permit gre host 96.###.25.226 host 184.###.###.254
permit gre host 96.###.25.226 host 70.###.172.142
logging host 10.100.###.254
logging host 10.100.###.246
snmp-server community P_RW RW
snmp-server community P_RO RO
snmp-server community a RW 20
snmp-server community r RO 20
snmp-server community a RW 20
snmp-server community r RO 20
snmp-server enable traps entity-sensor threshold
snmp-server host 10.100.###.246 public
snmp-server host 10.100.###.254 public
access-list 20 permit 10.###.9.3
access-list 20 permit 10.###.8.16
access-list 20 permit 10.100.###.249
access-list 20 permit 10.100.###.254
access-list 20 permit 10.100.###.246
control-plane
banner motd ^CCCCCC
****************** Warning! Warning! Warning! ********************
This system is restricted to authorized users for business
purposes. Unauthorized access is a violation of the law. This
service may be monitored for administrative and security reasons.
By proceeding, you consent to this monitoring
****************** Warning! Warning! Warning! ********************
^C
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
exec-timeout 60 0
password 7 *removed*
login local
transport input ssh
line vty 5 15
exec-timeout 60 0
password 7 *removed*
login local
transport input ssh
scheduler allocate 20000 1000
ntp server 10.###.8.8 prefer
ntp server 10.###.231.200 prefer
ntp server 10.###.8.69
ntp server 10.###.1.6 prefer
endUPDATE
I have since applied the following config to the tunnel interfaces:
ip mtu 1400
ip tcp adjust-mss 1400
tunnel path-mtu-discovery
This worked and I was able to reset each users PC to default MTU size of 1500, but only until just now. I got a call from a user who explained that he wasn't able to reach some websites, again.
Sure enough, I've just confirmed that all of the users are unable to access the websites any longer.
This is crazy, does anyone have any ideas? -
Advanced mode in receiver FILE adapter
Hi there,
Does anyone of you have a list of aditional parameters to be specified in the receiver FTP communication channel?
The only one i found is ftp.timeout and this is available on my default FTP connetion parameters.
Thanks a lot in advance,
DavidHi David,
Additional parameters are published in SAP Note 801926
Also Check this one.
http://help.sap.com/saphelp_nw04/helpdata/en/ae/d03341771b4c0de10000000a1550b0/frameset.htm
**Reward points if usefull***
Maybe you are looking for
-
Unable to delete file on the remote host
Hi, I tried to delete a file on the remote host using File.delete method as well as using Runtime.getRuntime.exec("del filename") But both of them failed to work. First one returned false, but the second one is throwing IOException always. I am tryin
-
Legacy MBP vs. 2009 MBP
Hello All, I'm finally in the market for a new 15" MBP to replace my 2.16 GHz variant of the first generation MBP! I'm an architecture student and my core pro uses are running CS4 on the Mac side and various CAD/rendering related applications on the
-
Why do I have problem importing iTunes purchases to iMovie 6?
I am quite frustrated. Because of all the problems I was having with iMovie 4, I recently upgraded my system to OS Tiger 10.4, my iMovie to version 6 and all other iLife components to version 8 (my processor doesn't support iMovie 8). Now I have a wh
-
Use 3 button or property to change selection of radio buttons?
Hi all, I have LV 7.1 and am trying to write a process that allows the user to select the next action following the execution of several Case Structure steps. The VI is basically thus: (sorry I can't cut-n-paste a graphic, it's on another pc.) While
-
Cant play my MOD video clips no matter what i try..
Last year i was making a dvd out of my home clips and got a lot of help to convert the files so i was able to do so on this imac. I had got a JVC Hard Drive video camera so thats what caused the problems. Anyway it has been sooo long since i did that