EA6300 Slowing my speed greatly.

I have a EA6300 set up in my small duplex and it is crippling my download speeds.
Ran a program called Network Logger for 24 Hours hard wired into modem, had an average 88.03Mbps Download and 19.1 Mbps.
Another 24 Hours wired into router 84.11Mbps down and 19Mbps up. Awesome.
24 Hours on 2.4Ghz network roughly 30 feet from router 9Mbps down and 4.4Mbps up.
24 Hours on 5 Ghz network same place in house 11Mbps down and 997 kbps up (I would trim this upload, but its 24 hours with a 30 second refresh rate)
I have no cap on my usage, and I also pay for 70+ Mbps. This wireless is killing my speed, what gives? Linksys says they want to replace the router, but the **bleep** thing is brand new. I have the router set up exactly as Linksys told me to, prioritization is disabled.
Iphone 5 gets a good 3.3 Mbps dl and 2 Mpbs ul on average on either one of them.
Other information (This is from inSSIDer)
5 Ghz
RSSI -70 Channel 36 + 40 WPA2 Personal Max Transfer Rate 450Mbps
There is no (0) other traffic on the lower 5 Ghz freq
2.4 Ghz
RSSI -52 Channel 3 WPA2 Personal Max Transfer Rate 130Mbps
There is a bit of traffic on the 2.4Ghz freq, but Channel 3 and 4 are not used (except by me) Channel 7-11 are extremely clogged and Channel 1 has about 5 networks on it.
Also to note, on the 2.4 Ghz channel my PS3 gets 2-4Mbps down and 700kbps up in roughly the same place as the laptop. If anyone has any ideas on how to speed this up that would be quite useful.
Note: Up until about a week ago the only thing I knew about wifi was how to use the wizard when you get a new router. I am catching up, but bear with me.

for the fun of it Disable IPV6;
lots of ussus there;
Chris

Similar Messages

WRT310N Playstation 3 Slow Download speed and general lag

Hey guys, I just recently bought the WRT310N and got both of my computers working with it. One is wired directly into the router, while the other is running off wireless. My Playstation 3 is able to connect to the router but I am getting an extremely slow connection speed.
Right now, both PC's get about 6.4-6.5 Mbps download speed while my Playstation is anywhere from 600 Kbs to 1.2 Mbps. I have plugged in my Playstation 3 directly into the modem and got a speed of 3.2 Mbps and was downloaded a demo very fast, but I do not recieve anywhere near those results when using it wireless.
Any advice? I have tried opening the ports, but that only seemed to slow it down. A couple of days ago I opened the ports specific to the game NHL 10 and for two days I was getting such a good speed in the game that it felt like I was playing offline, which was great! Then this morning, it just seemed do a complete 180. Now when I play the game I get an extreme amount of lag, and my other games like CoD4 get random lag spikes. Like, I'll be running and I get a lag spike which seems to happen fairly consistently every minute or so.
Any advice? Should I try opening the ports again or what?
Message Edited by Nimer on 10-02-2009 03:58 PM

I think you need to adjust the wireless settings of your Router, The wireless settings on your Router must have been setup to its default that's the reason you are receiving low signal strength on your PS3.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Here select manual configuration...Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select TKIP...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and remember the key.
NOTE : Passphrase should be more that 8 characters...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

Mac Pro slow write speed on Samsung SSD drive

Hi,
I am wondering why I get very slow write speeds on my Samsung SSD 840 Series 250 GB system startup drive in my Mac Pro (early 2008).
I get an average write speed of approx. 35 MB/s and not much more for top speed. I tested it by transfering a large file (8GB, .m4v) from my Mac Pro internal Raid 0 (4x 2TB Stripe Set) delivering up to 550 MB/s. The read speed of the SSD is around 270 MB/s which I consider to be OK for that I have just the 3 Gb/s internal SATA interfaces in my pretty outdated Mac Pro.
I don't see any Memory or CPU overruns or consuming system tasks while doing the tests and no other user programs except Activity Monitor is running. The following screen shots from the Activity Monitor should proove my findings:
Setup:
Samsung SSD 840 Series 250 GB (SATA 6Gb/s and 3Gb/s compatible) system startup drive. Free Space left on SSD is around 100GB of 250GB.
Mac Pro (early 2008, Model 3,1), 2 x 2.8 GHz Quad-Core Intel Xeon, 8 GB RAM, NVIDIA GeForce 8800 GT 512 MB.
OS X Mavericks 10.9.1
Samsung sais there should be 540 MB/s for Seq. Read and 250 MB/s for Seq. Write for their SSD drive.
Any hints what could be done to increase especially that low write speed of around 35 MB/s (average) on the SSD in my Mac Pro?

Really great 'The hatter' !!!
Thanks a lot for your exceptional support.
Next to my 4x discs in the 4 SATA II drive bays I have installed a additional OWC drive kit that allows me to have another 2 disks sitting in the empty bay below the CD/DVD drive and those are connected to the motherboard. So there is a lot to handle for that controller you mentionned ;-)
I will follow your guidance and boot from my 'maintenance' system on direct attached external drive, install the TRIM Enabler there as well and do the DU repair run. I always have a separate system available that gives me the chance to boot my Mac from there. And in addition I regularly use ONYX to keep my OS X clean and do the maintenance.
Anyway, you're the man of the day!
PS; I am looking forward to finally receive my new Mac Pro (late 2013) ordered on the 18th of December one of these days and then I hope that I can fly ;-)

Incredibly Slow broadband Speed

Hi, I'm servering from a Incredibly Slow broadband Speed and can't nail the reason why.
The broadband for my street was down for a whole weekend although box said connection was ok - helpline was no help - just said try again tomorrow. Now we have internet but the speed is very very slow - speed test results are :
Download = 53 kps
acceptable range = 100-250 kps
DSL Connection Rate 486 Kps (Down-Stream), 712 kps(Up-Stream)
IP Profile for line = 135 kps
Upload = 541 Kps
Addition Hub Info:
Noise Margin (Down/Up) = 8.5 dB / 6.7 dB
Line Attenuation (Down/Up) = 63.8 dB / 35.8 dB
Output power (Down/Up) = 1.3 dBm / 1.1dBm
Prior to loss of service, my speeds although weren't great were about 1.2 Mps
I've tried all the suggestions like changing channels, filters etc and nothings change in my house since the degrading of service.
Can someone please help !
Best regards

I don't know if this will help, but I do notice that your output power is only 1.3dBm / 1.1dBm. can I ask you to look on the back of your home Hub and check to see if it is a Type A or Type B, this will be on the label in the bottom right corner. If it is a type B Hub then ring and ask for a Type A Hub as I have found that I get a better output power reading of around 16.0dBm. When I was sent out a relacement Hub when mine went wrong they sent out a Type B and my speed went very slow, so I put the original Type A Hub back on to see if it made a differance and my speed increased and my IP Profile went up. So if this is the case, ring up tech support and don't ask tell them that you wont a Type A replacement Hub. All the best in your efforts and don't forget that the more you insist the more you can achieve.

Slow Inernet speeds and navigation

Hello.. I am a newbie so hope I can explain my problem accurately.
My Desktop PC is really slow espcially when I am accessing websites using either Chrome or IE.- Even Youtube is very choppy- ( Note..I have the latest version of both browsers but they are slow. (I am wired to my modem)
When I check the speed from my ISP using my HP desktop it is significantly slower than when I connect another laptop to my modem.
I have done all the virus updates,malware, disk clean up/defrag but it is still slow.
Navigating to other menus (My compuer, control panel etc) is not the best but it could be better in terms of speed
Could there be something wrong with graphics card or some other hardware? How can I test this.
I dont do gaming but I think this PC should be much better.
I appreciate your direction.
Here is the specs below. Let me know if you need more information.
HP CQ2025
AMD E-450 APU with Radeon HD Graphic 1.65GHz
4.00GB(3.60GB usable)
64bit OS
919GB HD (65.7 used)

Hello @Snooziedon,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that you are not getting the internet speed that you are expecting from your Compaq CQ2025 Desktop PC. I am providing you with two HP Support documents: Resolving slow system performance (Windows 7) and HP Academy: Speed up your Internet Connection in Windows 7, which I would suggest you review both and apply the suggested steps within to get your slow internet speed issue resolved.
Please re-post if you require additional support. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Slow network speed during peak times

I have begun experiencing very slow network speeds in the evening. My Mifi and other devices go from routinely getting 10 MBS down to 1 MBS in the evening. Is there any way to address this?

Rickrdn1,
Thank you for all of the detailed information. The coverage in the area looks great. All of your devices seem to drop in speeds at the same time? How is voice and text working during these times? The coverage in the area looks great, but can still be affected by congestion at peak times of usage. We may want to investigate your area further with a remedy ticket.
TrevorC_VZW
Follow us on Twitter @VZWSupport

Slow transfer speeds between two macs

The general setup: an iMac Intel 20" and an iBook G4 1,2GHz connected via an Airport Express (newest edition), both computers running 10.4.7.
When trying to transfer files via AFP between the two on my local network, I get "tremendous" speeds of about 0.5-1 MB/sec. Why is this so incredibly slow? Is it because of encryption or something similar? I can download off the internet with greater speed than that!

i have exactly the same problem , using a macbook black g1 . slow network speeds and flakey internet . these were ok when I first got the machine . but are now slow as . using the network view of menumeters I see that if i try and shift files from my mac mini they are incredibly slow with menumeters show 0.0kb/s for seconds at a time .
to trouble shoot this problem I used another friends macbook configured with exactly the same settings on this network and the transfer speeds were as they should be which was about 1.5-2.5 megs/sec .
so i figure there is some preference corrupted but which one ?
I have experienced several crashes recently . because of the overheating bug I have the fix applied to my machine and the firmware update . Maybe the network preference got corrupted at that point .
any tips as to which preference to delete would be appreciated .

WRT160N V1 slow N Speeds , good g speeds

so i have a wrt160n v1 and the n speeds are horrible. very very slow. it works great on comps with a g card only but my brand new comp that has an n card that i paid extra for dont work at all hardly, its under 1mbps. so i went and bought a new wrt160n v3 the other day, hooke it up, configured it, and it works great on my new comp.
is there anyway i can get the v1 to work as good as the v3 ? there are no firmware updates for the v1 past 2008:-/ HELP ME!!!!!

i think the the router and my comp dont mix. when i secure it thats what caused the probs. the wap2 security i think cause when i removed it , it improved if i took the comp away from it. but i went out and bought the wrt320n tonite at walmart and its like WOAH. it works way better and speeds are constant and fast and idle speed is good. and when i speedtest it, its constant. im content with the new one . and the old one is i think just junk lol. cause it wolnt seem to work, its out of warranty so im screwed and had no choice
if u have any suggestions im open to any, i have 45 days to return the gigabit router.

Firmware Password protection = slow firewire speeds

i've been trouble-shooting a seagate freeagent fw800 external drive which is suffering from abnormally slow read speeds when connected to my macbook pro. i tested it with Drive Genius's Benchtest - around 8mb/s. the drive works fine on my imac, so the drive isn't at fault.
after much head-scratching, i remembered that i have firmware password protection switched on, so i just turned it off with the 10.6 dvd and retested the drive, and it performs normally (around 40mb/s).
i've not found any mention of this issue apart from one post from 2 years ago:
http://discussions.apple.com/thread.jspa?messageID=8448187
so now i have to choose between a safer mac, or decent read/write speeds for my audio multitracking work. great. its not exactly convenient having to turn FPW on and off via the dvd...
anyway just thought i'd mention this for future baffled searchers.
reported it as a possible bug to apple too.

This should allow you to reset the root password
1. Restart your MBP while holding down Apple/S
You will see a bunch of scrolling text, when that stops
2. At the Localhost% prompt type:
*/sbin/mount -uw /*
/sbin/SystemStarter 
You will then see the services starting up.  
3. When the Localhost% prompt reappears, type:
*passwd root *
It will then ask you to type the new root password twice
4. After entering the new password, type:
reboot
5. Login as root with your new password and proceed from there.

From the old forum.... Slow broadband speeds in th...

FROM THE OLD FORUM Original post by John Jorgensen...
Slow broadband speeds in the evening all of a sudden
Posted: Jan 22, 2010 9:17 AM
Click to report abuse...        Click to reply to this thread    Reply
Hi,
I have had bt broadband opt3 for almost 3 months now and have always had a healthy 9mb+ connection, however have noticed it being very slow in the evening when I come home from work, I checked the speed last nite as iplayer was constantly freezing and was getting 1mb . A bit upset by this as I got bt broadband to play my ps3 online and to get faster speeds on my laptop, and I use these services mostly at nite.
I checked my speed this morning and was getting 11mb, is this normal or am I being capped I cant believe Id be going over my download limit. Can someone from bt get back to me on this?
Thanks
John
alison griffiths
Posts: 54
Registered: 11/3/09
   Re: Slow broadband speeds in the evening all of a sudden
Posted: Jan 22, 2010 11:22 AM   in response to: John Jorgensen in response to: John Jorgensen
Click to report abuse...        Click to reply to this thread    Reply
Welcome to the world of BT , the tv advert when he says " business slow" when trying to load a webpage is not other companies thats BT.
John Jorgensen
Posts: 2
Registered: 9/2/09
   Re: Slow broadband speeds in the evening all of a sudden
Posted: Jan 22, 2010 12:11 PM   in response to: alison griffiths in response to: alison griffiths
Click to report abuse...        Click to reply to this thread    Reply
Yes Alison, I think I can see that now. I wouldnt mind if broadband was a bit slower at peak times, I know thats normal, but when I'm only getting 1mb when my max is 14mb, I just dont feel I'm getting what I pay for. And when it gets to the point where I cant watch iplayer without it stuttering everywhere and online games lagging on the ps3, this is certainly not what I'm paying for.
I was hoping one of the mods here would help me and check my line and see if there is any cap on the line and get it removed.
I really dont wanna phone India, I deal with them 5 days a week as is...
Think I will just send one of the mods an email to check my line and see if it is being capped or if somethings wrong.
anthony dickerson
Posts: 72
Registered: 4/26/07
   Re: Slow broadband speeds in the evening all of a sudden
Posted: Jan 22, 2010 3:52 PM   in response to: John Jorgensen in response to: John Jorgensen
Click to report abuse...        Click to reply to this thread    Reply
You will never get decent speeds on Iplayer,
BT limit it because they want you to subscribe to their precious BT Vision service.
The only way you are guaranteed to get decent speeds on BT is to subscibe to BT Vision and also unlimited broadband.
Then you will get priority when you stream TV at your exchange unlike fighting it out with all the other broadband users as you currently are for the available bandwith.the more over subscribed your local exchange the worse it is
Paddy B Mod
Posts: 199
Registered: 10/13/08
   Slow broadband speeds in the evening all of a sudden
Posted: Jan 23, 2010 2:04 PM   in response to: anthony dickerson in response to: anthony dickerson
Click to report abuse...        Click to reply to this thread    Reply
Hi John,
I can take a look at the network side of things for you, to see if there is anything I can do to help improve your speed during peak periods. Please could you drop me an email with your BT account details? Please also include a link to this thread. It would also be very helpful if you could run a few speed tests using www.speedtester.bt.com when you feel your Broadband is running slow. I can then check those results from here.
Thanks
Paddy
BT Forum Moderator - [email protected] - if you're emailing please include a link to your thread so I can reference back to it.
Mateusz Sokolin...
Posts: 2
Registered: 10/11/08
   Re: Slow broadband speeds in the evening all of a sudden
Posted: Jan 24, 2010 7:33 PM   in response to: John Jorgensen in response to: John Jorgensen
Click to report abuse...        Click to reply to this thread    Reply
Well John i'll tell you what it is...
First of all welcome to BT and I hope you'll enjoy 18months of pain and suffer.
OK here it goes....
If you look at your contract, find a rule that says Fair Usage Policy.
Basically it states that BT will cap anyone that is abusing their lines.
However, it does not say what are the limits after which you are going to be capped for how long and at what times. (I'll come back to this later and explain)
If you ring 08007076044 I'm sure that someone will confirm my theory. As constant 1MBit between 6PM till 11/12 PM is actually FUP applied on to your account.
Ok time to explain my frustration about FUP.
Since I signed my contract with "lovely" BT for constant 4 months I had similar issue but it took me even longer to find out what is going on and how to deal with this problem (thanks to google).
FUP team states that if you exceed 100GB in a month (everyone will admit that these days 100GB is nothing when a single game for PS3/XBox360/PC sometimes is more than 5GB and 1080p film is about 12GB) will cap you for a month at peak times to outstanding and superfast 1Mbit (about 130-150KB/s).
I'be been watching my download and for few months never exceeded that 100GB in a month. Been ringing FUP team to verify when suddenly they told me that from (cant remember exactly) March FUP will apply only to accounts that are using Torrents and other P2P.
you won't believe how happy I was hearing that.... So i've started to download and next month guess what.... 1Mbit connection.
Really mad rang FUP team and asked them what on earth is going on. They confirmed that its only P2P and I've explained them that I only use Youtube, BBC iPlayer, Rapidshare, Steam and XBox Live, Beatport (just don't understand how ppl can use torrents and other P2P as they are just way to slow). So they were happy to take the cap off my broadband connection.
Next month same issue solved exactly the same way.
After that for consecutive few months I had no problem whatsoever until September where FUP Team said that there is no such thing and FUP applies to everyone.
So just want to say that BT is rubbish that can't keep their word.
I went to one of the sales advisor in the shopping centre and asked him how FUP works as it does not say in the contract "how, when, who and what".
So he said that policy is applied based on amount of files downloaded within that 100GB. So if I download e.g. 3x 50GB (although its 150GB altogether) files I wont be affected but 100x 1GB will put a cap on me.
I've been so curious if what he said was right and started to download 2x 60GB and guess what... Got frigging FUP placed on my account!!!.
I've got 2months left with them and will be extremely happy to cancel my contract, moreover, I will do everything in my power to sue them under EU Consumer Rights Law (that states that contract should be clear and fair to both sides) as Fair Usage Policy is one of those things that allows BT to do anything they want to their customers;
1. No clear explanation of what FUP is.
2. Does not states the amount of downloaded data required to have cap on the acount
3. Does not states for how long it will be applied
4. Does not states when it will be applied
If you look at e.g. Virgin Broadband everything is clearly written in nice and understandable way. It warns you at what times FUP will be applied under what circumstances and for how long. Isn't it what we all want to know??
Alex Owen
Posts: 3
Registered: 12/13/09
   Re: Slow broadband speeds in the evening all of a sudden
Posted: Jan 24, 2010 9:35 PM   in response to: Mateusz Sokolin... in response to: Mateusz Sokolin...
Click to report abuse...        Click to reply to this thread    Reply
@Mateusz I think I maybe a victim of this outragous stint BT have done. I have 2 XBOX 360's running on XBOX Live, 2 Desktop PCs connected to the web constantly, and 3 laptops, we have a torrent sharing running and World Of Warcraft on one of the PCs. All of this is shared across a 6 person family. How can a family where two members goto to college and university do their college ork, download application such as VB.net do their coursework and revise without the hassle of a **** connection. Seriously BT get your ******* head outta your **** and stop this ********, we are customers, we pay for what we are offered. When I signed up several years ago I could download everything on the net woithout infracions on my line being set in motion. You altered my contract without telling me. You will lose custom from this. Also you have ****** my wireless
Edited by: Alex Owen on Jan 24, 2010 9:36 PM
amanda jones
Posts: 33
Registered: 1/8/10
   Re: Slow broadband speeds in the evening all of a sudden
Posted: Jan 25, 2010 8:42 PM   in response to: Alex Owen in response to: Alex Owen
Click to report abuse...        Click to reply to this thread    Reply
You lot are lucky, We wish we could be capped to 1mbit. Our IP profile is capped to 500kbit because BT say the line isn't good enough for anything more. We are paying for option3 up to 8mbit and BT have said we must continue to pay for it for the remainder of the contract, or buy ourselves out of it early, the reason they give.... Up to 8mbit means up to 8mbit. If you dont get 8mbit then TOUGH LUCK SUCKERS!!
The outcome? We feel like we've been turned over by a dodgey second hand car salesman called BT. The internet deal he flogged us was a dog, a ringer, it wasn't cosher and certainly had a false MOT certificate.
Computer Geek
Posts: 429
Registered: 7/22/05
   Re: Slow broadband speeds in the evening all of a sudden
Posted: Jan 25, 2010 8:49 PM   in response to: amanda jones in response to: amanda jones
Click to report abuse...        Click to reply to this thread    Reply
Hi Amanda,
Why have you joined BT Option 3 when you can not get what BT can offer?
No pun intended but you are a bit of a sucker for paying high prices where other suppliers are cheaper and can provide what your line can support.
CG
amanda jones
Posts: 33
Registered: 1/8/10
   Re: Slow broadband speeds in the evening all of a sudden
Posted: Jan 26, 2010 9:13 PM   in response to: Computer Geek in response to: Computer Geek
Click to report abuse...        Click to reply to this thread    Reply
we moved house last october to this one, the connection was rubbish from the get-go, BT said the router was broken and we needed a new one, we said OK. That "OK" meant that we had entered into a new contract for option 3 same as out old one. The router wasn't broken, the new one didnt fix or improve the problem, we have since asked for a price reduction or compensation and been told "no". we are in contract and can pay to buy ourselves out of it if we like but otherwise we have to pay for option 3 and recieve fixed rate 500kb.
Clare Thurston
Posts: 4
Registered: 10/17/06
   Re: Slow broadband speeds in the evening all of a sudden
Posted: Jan 27, 2010 11:57 AM   in response to: amanda jones in response to: amanda jones
Click to report abuse...        Click to reply to this thread    Reply
Hi Amanda,
I think you'll find that the Hold To Term rules have changed. BT are now unable to charge you for the account if you no longer require it. It is against OFCOM's rulings for a company to make more money out of you as a leaving customer than an existing one. However, You will need to pay for the connection charge (if that has not expired it's original differed contract) which is £40. A cancellation fee of £25 if you are simply cancelling and not migrating using a MAC key and for any hardware. The Routers are advertised at £88 and i would suggest that if they believed on to be faulty then that would be replaced under guarantee and not be put on a differed basis. I would check exactly what they say the are charging you and query this through OFCOM. http://www.ofcom.org.uk/

Months of impecable service form BT as an option 3 customer. (I've even recommended BT to people)
but
For the past 2 weeks peak traffic has murdered my connection.
I can get 14mbit off peak, and it used to drop to about 7-9 at peak times.
Now its down to 1-2mbit at peak times. (no i haven't breached FUP as I check my btinternet inbox for the 80GB warning)
I think its resonable to experience drop off but 90%!!!
BT advertising says fast speeds at peak times. less than 2mbit is not fast. (that the governments minimum standard!!!)
I don't know how to procede because when I'm experiencing these issues if I ring up I will end up waiting so long to speak to someone (because its peak time) the concection wiill be better again.
I can think of no recourse other than to approach trading standards...
Guarnetee me 5mbit at peak times (enough to stream HD iplayer) and I'd be happy
That is what BT vision customers are in essence are getting + what ever their PC is using.
Fair usage? what about Fair Supply.

Time Capsule with an Airport Extreme bridge resulted in slow LAN speeds

Wondering if other people are seeing this. I am unsure if this was a result of upgrading both my TC and AEx to 7.6, but my LAN speeds had suffered in this configuration.
1. Comcast cable modem connected to the WAN port on my TC.
2. Connected an ethernet cat6 cable from the TC to my Airport Extreme, which was configured as a bridge.
3. My desktop was connected to the Airport Extreme.
4. When doing file transfers within the LAN or general internet usuage, my network speeds were extremely low.
5. Disconnected the cat6 cable from the TC and plugged that directly to my desktop.
6. Network speed jumps up by a factor of 5. LAN file transfers and internet usuage has returned to what I had expected.
Is there a known issue where a bridged AEx conncted to another Airport "main" device will result in all machines connected via the AEx to have slow LAN speeds?
I didn't see this issue months ago. I did less than 2 months ago upgrade our machines to the 7.6 firmware, but after experiencing some hiccups on the network, reverted back to 7.5.2. However, the slow LAN speeds haven't gone away when the two airport machines are connected to each other.
Any insight or advise is appreciated.

By now, millions of users have updated to 7.6 and I cannot recall seeing a post similar to yours on this forum.
As far as a "known issue", you would need to contact Apple regarding that.
Suggest that you have the AirPort checked out at an Apple store if you have one near you.

Very slow broadband speeds

Hello
My first post, and I'm hoping that someone will be able to help me with this.
For a few days now, I've been experiencing very slow broadband speeds (100kbps or less), in contrast to the 1.5 - 2Mbps that I would usually expect to get. I've been on hold to BT technical support for some time, and have got through twice, on both occasions being told that this is a widespread issue and to wait until the next day. However, I'm not seeing any improvement. I'm aware of the problems in Edinburgh and the North of England,but I'm in East Anglia.
speedtester.bt.com shows:
Your configured download throughput speed for this service is 135 k
and then:
Two consecutive attempts have failed to initialise an Assured Rate session for your service.Please raise a fault with your service provider stating that the Performance Tester tool indicated a problem with initialising your Assured Rate session. <script type="text/javascript">// paintProgressAndMessageTestBar(-1,""); paintProgressAndMessageOnBar(-1,'An Error has Occured! '); // </script>
My hub stats are:
ADSL line status
Connection information
Line state Connected
Connection time 1 day, 13:59:54
Downstream 1,504 Kbps
Upstream 448 Kbps
ADSL settings
VPI/VCI 0/38
Type PPPoA
Modulation ITU-T G.992.1
Latency type Interleaved
Noise margin (Down/Up) 15.0 dB / 19.0 dB
Line attenuation (Down/Up) 60.0 dB / 31.5 dB
Output power (Down/Up) 16.6 dBm / 11.9 dBm
Loss of Framing (Local) 0
Loss of Signal (Local) 0
Loss of Power (Local) 0
FEC Errors (Down/Up) 4586 / 92
CRC Errors (Down/Up) 297 / 2147480000
HEC Errors (Down/Up) nil / 72
Error Seconds (Local) 221
I hope this is enough information, but I'll happily supply anything else if I can. The uptime of 1.5 days is the time since I was advised to restart / reset to defaults etc.
Thanks for any help.
Deej.

Once a line is stable and working well, it's best left running 24/7
Interventions like resets, replacing accelerators, unplugging the router etc. will cause line "flapping"
And the dslam sees this as instability, and in turn the BRAS lowers the IP profile ....
This is done to achieve stability, and decrease throughput purposefully, all done automatically.
What you have to do, is cure any line noise, plug directly into the master or test socket behind the NTE
faceplate, leave it connected and wait for the throughput to increase.
Very often a rock bottom IP may need a kick to get it out of the doldrums.
Eventually the noise margin will decrease, sync will increase, and IP profile go up.
Depending on how long the line has suffered impulse noise, will determine the time for SNR to come down.
Regardless of which type of phone you used to test quietline ... hum or crackle is a no-no.
It may be the cause of the problems. It could be REIN on the network portion of the connection or dslam
crosstalk, either way it needs to be reported as line noise before you can count it out of the equation.

External firewire hard drive reverts to slower transfer speeds

This is the strangest hardware problem I've come across. I'm running a unibody mbp (June 2009) with an external WD 2.0TB Caviar Green drive mounted in a firewire 800 enclosure made by icydock.
Lately, I've noticed that after an unknown amount of uptime, the speed of file transfers to the WD external drive slows down dramatically. I figured this out by watching my time machine transfers take a bit longer after awhile, and I verified this using aja system test and speedutilities.
When I boot my mbp in the morning, file transfers and time machine backups to the external WD transfer at a rate of about 67-75MB/s. This is the speed the drive should always be working at since it's connected via firewire 800. Aja speedtest verifies the speed is as it should be as well.
Then, after a couple hours of using my mbp, or even later in the day, I'll transfer a file to the external WD or run a time machine backup and find that the transfer will only run at a max of 29-35MB/s. This is exactly half the speed the transfer should be going at. Subsequent transfers stay at this slower rate no matter what I do.
However, I've been able to fix this problem by unmounting and remounting the external WD or restarting my mbp. After doing either of these actions, the WD external goes back to contant transfers at 75-80Mbs. So something is happening where the longer the mbp is running, or after some sort of disk activity, the external WD reverts to a slower transfer speed (closer to FW400). I can't isolate whether it's an issue on the mac os side or the hard drive or the hard drive enclosure because I can make the hard drive go back to optimal speed again merely by unmounting and remounting it. This works consistently until a few hours later when the drive begins to handle transfers at half speed again.
I run hourly time machine backups to the drive. The time machine backups can't be the culprit because the drive remains running at optimal speed after the backups (verified with aja system test and speed utilities)
Any possible ideas as to why the drive cuts down to half its optimal transfer rate after a bit of time? I can't figure out the cause of this, and the consistency of the drop leads me to think this is an issue with the power management on the drive since it reverts to full fw800 speed when I umount and remount the drive or restart my computer. Could this be an OSX issue where for some reason the system isn't negotiating the fastest speed?
Any help appreciated.

From the SoftRAID manual:
Fire hubs and disk drives. FireWire hubs are notorious for introducing errors and instability onto the bus.
Make sure that all of your consumer electronic devices (iSight, cameras, scanners) are connected to a separate FW bus. These devices are not built to the same standards as storage devices and known for introducing errors onto a FW bus.
Cables. While most cables work fine with a single device, many cables will introduce errors when 2 or more disks are connected to the bus.
http://www.softraid.com
http://www.softraid.com/demo.html - manual and demo
Output can be to any drive or partition. When you lauch iMovie it asks where to store your project.
I just bought a camera, and curious myself to see if I can take 10 minute clips and use iMovie/iDVD so that it will auto-play. I may end up buying Pogue's "iMovie Missing Manual" or something.
iMovie Discussions

Macbook pro: Extremely slow upload speed

Hi,
I know this question has beed raised many times before me, seemingly from hundreds or thousands of users, but none of the threads I have found has lead to any solution.
My new Macbook Pro (15 inch), using Lion 10.7.3, is simply unable to obtain anything but an extremely slow upload speed, when using Wifi. I am using an Apple Airpor Extreme wifi device. My work PC, my older Macbook Pro (13 inch), all tablets and telephones etc hooks up to the same Wifi device and obtain all the speed they should, but my new Macbook Pro is sloooooooooooowwwww and sometimes cannot even initiated an uload speedtest at i.a. www.speedtest.net.
As mentioned, I am aware that there are plenty of threads on this, but I am not aware of any that provides a solution.
Is there a solution or is my new Macbook nothing but crAplle?
Best regards,
n

My subscription is 10 Mbps downloadand 2 Mbps download. upload
I get that (10/2 Mbps) on all other devices, other than my new Macbook Pro.
On my new Macbook pro I get 10 Mbps download, but only from 0 to 25 Kbps upload.

[SOLVED] Slow read speeds from a DroboFS mounted in fstab via cifs

I've decided to move all my media over to my drobofs which I have and I've mounted the share on the drobo in fstab this way:
//mydrobofs/Media /media/drobofs cifs iocharset=utf8,uid=af,gid=users,guest,dir_mode=0775 0 0
The share is mounted fine at boot but my issue is now the read speeds are very slow. opening a video file with vlc takes 30 seconds or more before it starts playing. Before this was accessing the share on my drobofs via the network tab (samba shares) in Dolphin (using KDE4) and here the video files played immediately in vlc (no delay). The reason why I want to mount the share via cifs and fstab is to move music collection over to the my drobofs and since I'm using Amarok for managing my collection this is the only way to make Amarok see my Music collection on the Drobofs.
Why am I getting so slow read speeds with cifs?
Last edited by fettouhi (2012-05-07 05:54:00)

I did some more testing and seems like the problem has something to do with how many video files there are in the directory. I have some directories with several 100 video files and here I get this long delay but if I play a file that is in a directory by itself or only a few other video files are there, then the video starts immediately (almost). Is there a way to turn off this behaviour in vlc? Is it generating a playlist or what?

EA6300 Slowing my speed greatly.

Similar Messages

Maybe you are looking for