EA6350 fails to load web pages, but all other online services continue working

Occasionally, when using the internet, web pages stop loading. Other online services such as messenger programs, Netflix, and online games still function properly. I usually end up having to restart the router in order to re-enable browsing. We are using the latest firmware, and only purchased the router about a month or two ago. I'm on channel 11, with only one other network on 11, and my 5 Ghz channel is irrelevant, as I'm the only 5 Ghz network in my area. Is the router defective? Is it a problem with a firewall or other program? Let me know if you need any more information. 

Internet Service Provider and Modem Configurations
What ISP Service do you have? Cable or DSL?
What ISP Modem Mfr. and model # do you have?
Is ISP Modem/Service using Dynamic or Static WAN IP addressing?
What ISP Modem service link speeds UP and Down do you have?
Check cable between Modem and Router, swap out to be sure. Link>http://en.wikipedia.org/wiki/CAT6 is recommended.
Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=88e63d78588142e6bb68e22d7faf2046_Configuring_the_M...
For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.
If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>http://www.practicallynetworked.com/networking/fixing_double_nat.htm and http://cognitiveanomalies.com/cisco-nat-how-nat-works/ If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ. 
I recommend that you have your ISP check the cabling going to the ISP modem, check signal levels going to the ISP modem. For cable Internet, RG-6 coaxial cable is needed, not RG-59. Check for t.v. line splitters and remove them as they can introduce noise on the line and lower the signal going to the ISP modem. Connecting to the ISP modem could result in a false positive as the signal to the modem could be just enough to that point then adding on a router, could see problems. Ensure modem is working well too. Bad modems are out there as well. The router operation is dependent upon getting good data flow from the ISP modem and the modem is dependent upon getting good signal from the ISP Service.
Any other WiFi routers in the area? Link> Use http://www.techspot.com/downloads/5936-inssider.html to find out. Use v3. How many?
WMM Support must be enabled for single wireless N mode to function.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&articleid=5471
Router Placement
Forum User - "Well I feel really dumb. After moving the router away from other electronic devices my speeds are back to normal. Just a heads up for anyone experiencing slow speeds, you might want to move it away from other electronics and see if that helps."
3-6' feet minimum safe distance between devices.
Placement on main level floor and central in the building and WELL ventilated is preferred. Not in basements or closets as building materials, or near by electronics devices could interfere or hinder good signal propagation.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=d9a3b1b2039741948a2365b053a93ea8_3759.xml&pid=80&r...
http://www.smallnetbuilder.com/wireless/wireless-basics/31083-smallnetbuilders-wireless-faq-the-esse...

Similar Messages

  • Safari cannot load web pages, but still communicates with the www

    I am using Safari 6.0.5 as my main web browser. Unexpectedly, a week ago it stopped loading web pages, though apparently the program somewhat still communicates with the world outside, since I can enter any text in the address bar and get responses in real time from Google.
    Other programs using the internet work regularly. I have already tried the usual set of solutions proposed in the official documents.
    Thanks in advance,
    Valerio

    16/07/13 08:32:44,048 SubmitDiagInfo[305]: Launched to submit Diagnostics and Usage
    16/07/13 08:34:58,455 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:34:58,455 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:34:58,456 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:36:20,212 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:36:20,215 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:36:20,216 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:37:40,026 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:37:40,028 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:37:40,029 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:39:24,687 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:39:24,688 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:39:24,688 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:40:31,347 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:40:31,348 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:40:31,349 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:40:37,794 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:40:37,796 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:40:37,797 apsd[72]: <APSConnectionNotificationQueue: 0x7fcb8484f1f0>: outstanding count -1 for com.apple.apsd-queue-port=com.apple.syncdefaultsd.push-user=501-env=production
    16/07/13 08:45:31,399 WindowServer[85]: CGXSetWindowBackgroundBlurRadius: Invalid window 0xffffffff
    16/07/13 08:45:31,419 loginwindow[57]: find_shared_window: WID -1
    16/07/13 08:45:31,419 loginwindow[57]: CGSGetWindowTags: Invalid window 0xffffffff
    16/07/13 08:45:31,419 loginwindow[57]: find_shared_window: WID -1
    16/07/13 08:45:31,419 loginwindow[57]: CGSSetWindowTags: Invalid window 0xffffffff
    16/07/13 08:45:31,438 loginwindow[57]: ERROR | -[LWBuiltInScreenLockAuthLion preLoad] | guestEnabled is true, but guest mode is not set to a usable value
    16/07/13 08:45:31,782 WindowServer[85]: Created shield window 0x5a for display 0x04280380
    16/07/13 08:45:31,783 WindowServer[85]: device_generate_desktop_screenshot: authw 0x7feb82c49380(2000), shield 0x7feb82c24510(2001)
    16/07/13 08:45:31,873 WindowServer[85]: device_generate_lock_screen_screenshot: authw 0x7feb82c49380(2000), shield 0x7feb82c24510(2001)
    16/07/13 08:45:31,929 loginwindow[57]: *** WARNING: -[NSImage compositeToPoint:operation:fraction:] is deprecated in MacOSX 10.8 and later. Please use -[NSImage drawAtPoint:fromRect:operation:fraction:] instead.
    16/07/13 08:45:31,930 loginwindow[57]: *** WARNING: -[NSImage compositeToPoint:fromRect:operation:fraction:] is deprecated in MacOSX 10.8 and later. Please use -[NSImage drawAtPoint:fromRect:operation:fraction:] instead.
    16/07/13 08:46:31,374 com.apple.time[11]: Next maintenance wake [Backup Interval]: <date: 0x7fd60be04910> Tue Jul 16 09:23:45 2013 CEST (approx)
    16/07/13 08:46:31,374 com.apple.time[11]: Requesting maintenance wake [Backup Interval]: <date: 0x7fd60be04910> Tue Jul 16 09:23:45 2013 CEST (approx)
    16/07/13 08:46:31,528 launchctl[319]: launchctl: Couldn't stat("/Library/LaunchAgents/com.oracle.java.Java-Updater.plist"): No such file or directory
    16/07/13 08:46:31,000 kernel[0]: AirPort_Brcm43xx::powerChange: System Sleep
    16/07/13 08:46:34,000 kernel[0]: LE is supported - Disable LE meta event
    16/07/13 08:46:34,000 kernel[0]: IOThunderboltSwitch(0x0)::listenerCallback - Thunderbolt HPD packet for route = 0x0 port = 11 unplug = 0
    16/07/13 08:46:34,000 kernel[0]: IOThunderboltSwitch(0x0)::listenerCallback - Thunderbolt HPD packet for route = 0x0 port = 12 unplug = 0
    16/07/13 08:46:34,000 kernel[0]: Wake reason: EHC1
    16/07/13 08:46:58,000 kernel[0]: AirPort_Brcm43xx::powerChange: System Wake - Full Wake/ Dark Wake / Maintenance wake
    16/07/13 08:46:58,000 kernel[0]: RTC: PowerByCalendarDate setting ignored
    16/07/13 08:46:58,000 kernel[0]: RTC: PowerByCalendarDate setting ignored
    16/07/13 08:46:58,000 kernel[0]: Previous Sleep Cause: 5
    16/07/13 08:46:58,000 kernel[0]: The USB device HubDevice (Port 1 of Hub at 0x1d000000) may have caused a wake by issuing a remote wakeup (2)
    16/07/13 08:46:58,000 kernel[0]: wlEvent: en0 en0 Link DOWN virtIf = 0
    16/07/13 08:46:58,000 kernel[0]: AirPort: Link Down on en0. Reason 8 (Disassociated because station leaving).
    16/07/13 08:46:58,000 kernel[0]: en0::IO80211Interface::postMessage bssid changed
    16/07/13 08:46:58,000 kernel[0]: en0: 802.11d country code set to 'X3'.
    16/07/13 08:46:58,000 kernel[0]: en0: Supported channels 1 2 3 4 5 6 7 8 9 10 11 12 13 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140
    16/07/13 08:46:58,000 kernel[0]: IOThunderboltSwitch(0x0)::listenerCallback - Thunderbolt HPD packet for route = 0x0 port = 11 unplug = 0
    16/07/13 08:46:58,000 kernel[0]: IOThunderboltSwitch(0x0)::listenerCallback - Thunderbolt HPD packet for route = 0x0 port = 12 unplug = 0
    16/07/13 08:46:58,000 kernel[0]: The USB device HubDevice (Port 8 of Hub at 0x1d100000) may have caused a wake by issuing a remote wakeup (3)
    16/07/13 08:46:58,000 kernel[0]: TBT W (2): 0x0100 [x]
    16/07/13 08:46:58,000 kernel[0]: The USB device Apple Internal Keyboard / Trackpad (Port 2 of Hub at 0x1d180000) may have caused a wake by issuing a remote wakeup (3)
    16/07/13 08:46:58,000 kernel[0]: HID tickle 175 ms
    16/07/13 08:46:58,297 hidd[61]: MultitouchHID: device bootloaded
    16/07/13 08:46:58,000 kernel[0]: NVRM: 0x702a called in D3
    16/07/13 08:46:58,000 kernel[0]: AppleUSBMultitouchDriver::checkStatus - received Status Packet, Payload 2: device was reinitialized
    16/07/13 08:46:58,878 WindowServer[85]: handle_will_sleep_auth_and_shield_windows: releasing authw 0x7feb82c49380(2004), shield 0x7feb82c24510(2001), lock state 3
    16/07/13 08:46:58,878 WindowServer[85]: handle_will_sleep_auth_and_shield_windows: err 0x0
    16/07/13 08:46:58,880 WindowServer[85]: Created shield window 0x5b for display 0x003f003d
    16/07/13 08:46:58,880 WindowServer[85]: handle_will_sleep_auth_and_shield_windows: releasing authw 0x7feb82c49380(2002), shield 0x7feb82c24510(2001), lock state 3
    16/07/13 08:46:58,880 WindowServer[85]: handle_will_sleep_auth_and_shield_windows: err 0x0
    16/07/13 08:46:58,880 WindowServer[85]: Created shield window 0x5c for display 0x003f003e
    16/07/13 08:46:58,880 WindowServer[85]: handle_will_sleep_auth_and_shield_windows: releasing authw 0x7feb82c49380(2002), shield 0x7feb82c24510(2001), lock state 3
    16/07/13 08:46:58,880 WindowServer[85]: handle_will_sleep_auth_and_shield_windows: err 0x0
    16/07/13 08:46:58,881 WindowServer[85]: Created shield window 0x5d for display 0x003f003f
    16/07/13 08:46:58,881 WindowServer[85]: handle_will_sleep_auth_and_shield_windows: releasing authw 0x7feb82c49380(2002), shield 0x7feb82c24510(2001), lock state 3
    16/07/13 08:46:58,881 WindowServer[85]: handle_will_sleep_auth_and_shield_windows: err 0x0
    16/07/13 08:46:58,923 loginwindow[57]: resume called when there was already a timer
    16/07/13 08:46:59,000 kernel[0]: en0: 802.11d country code set to 'IT'.
    16/07/13 08:46:59,000 kernel[0]: en0: Supported channels 1 2 3 4 5 6 7 8 9 10 11 12 13 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140
    16/07/13 08:46:59,061 configd[17]: network changed: v4(en0-:10.0.1.2) DNS- Proxy- SMB-
    16/07/13 08:46:59,328 hidd[61]: MultitouchHID: device bootloaded
    16/07/13 08:47:00,000 kernel[0]: MacAuthEvent en0   Auth result for: b8:c7:5d:05:67:5e  MAC AUTH succeeded
    16/07/13 08:47:00,000 kernel[0]: wlEvent: en0 en0 Link UP virtIf = 0
    16/07/13 08:47:00,000 kernel[0]: AirPort: Link Up on en0
    16/07/13 08:47:00,000 kernel[0]: en0: BSSID changed to b8:c7:5d:05:67:5e
    16/07/13 08:47:00,000 kernel[0]: en0::IO80211Interface::postMessage bssid changed
    16/07/13 08:47:00,000 kernel[0]: AirPort: RSN handshake complete on en0
    16/07/13 08:47:00,651 configd[17]: network changed: v4(en0+:10.0.1.2) DNS+ Proxy+ SMB+
    16/07/13 08:47:00,660 UserEventAgent[11]: Captive: en0: Not probing 'Ayn Rand 5 GHz' (protected network)
    16/07/13 08:47:00,663 configd[17]: network changed: v4(en0!:10.0.1.2) DNS Proxy SMB
    16/07/13 08:47:02,248 airportd[320]: _doAutoJoin: Already associated to “Ayn Rand 5 GHz”. Bailing on auto-join.
    16/07/13 08:47:02,263 airportd[320]: _doAutoJoin: Already associated to “Ayn Rand 5 GHz”. Bailing on auto-join.
    16/07/13 08:47:32,956 com.apple.backupd[330]: Starting automatic backup
    16/07/13 08:47:33,107 com.apple.backupd[330]: Backup failed with error: 19
    16/07/13 08:47:33,107 com.apple.backupd[330]: Starting automatic backup
    16/07/13 08:47:33,000 kernel[0]: nspace-handler-set-snapshot-time: 1373957255
    16/07/13 08:47:33,000 kernel[0]: nspace-handler-set-snapshot-time: 1373957255
    16/07/13 08:47:33,552 com.apple.backupd[330]: Attempting to mount network destination URL: afp://***;[email protected]/Time%20Capsule%20di%20Valerio%20Fi l
    16/07/13 08:47:34,000 kernel[0]: AppleSRP started.
    16/07/13 08:47:36,000 kernel[0]: CODE SIGNING: cs_invalid_page(0x1000): p=339[ksadmin] clearing CS_VALID
    16/07/13 08:47:36,000 kernel[0]: CODE SIGNING: cs_invalid_page(0x1000): p=343[ksadmin] clearing CS_VALID
    16/07/13 08:47:42,707 com.apple.backupd[330]: Mounted network destination at mount point: /Volumes/Time Capsule di *** using URL: afp://***;[email protected]/***
    16/07/13 08:47:42,000 kernel[0]: AFP_VFS afpfs_mount: /Volumes/Time Capsule ***, pid 332
    16/07/13 08:47:42,000 kernel[0]: AFP_VFS afpfs_mount : succeeded on volume 0xffffff80df13a008 /Volumes/Time Capsule di *** (error = 0, retval = 0)

  • Since upgrading to Maverick I cannot send/share photos through iPhoto. Dropbox says "not connected to server". All other online email activities work just fine.

    Since upgrading to Maverick I cannot send photos while in iPhoto.  Dropbox says I am not connected to server.
    All other internet email activities work just fine.

    And again why do you think Dropbox is involved in any way?  There is no connection of any sort between iPhoto and Dropbox
    THis sounds like you either need to (my personal suggestion) change your email client to Mail in the iPhoto preferenceemail if you want to use the iPhoto client under the accounts tab delete your account and re-enter it
    Ln

  • Hanging and non loading web pages but random

    Hi New to this so please excuse me if it doesn't make complete sense! We have been on BT infinity since Oct 2011 but we have been experiencing problems with access to certain web pages the pages either do not load or it just hangs, this has now been going on for about 6 weeks but it has now got a lot worse, we have had a friendly IT specialist look at our computer and he is now of the opinion that the problem lies with either the BT line or router, please see below what we/friendly IT specialist have done and please advise if our next step is to speak with BT?
    Thanks Mick
    Issue
    Vista Client Service Pack 2 laptop slow Internet performance failure to access some web pages.
    Known Troubleshooting Approach
    **** One or more combined of these operations would normally resolve in most cases ****
    Initially checked over system settings and allowed pending windows systems updates and other updates.
    Removed Trusteer Rapport software (known issues with slow performance) 
    Updated JAVA & Full re-install of Adobe Flash Player (components required for website animations\operations)
    (Note : Adobe Flash Component was not registered)
    Cleared Internet temp files (delete of web files\history\cookies etc)
    Reset of Internet Explorer settings (to address instability issues with Internet Explorer)
    Microsoft Security Essentials (Combined Anti Virus & Anti Malware Software)
    Quick scan (15 mins usually scans core components) -all clear
    Full scan (left to run approx 2 hrs) usually not necessary - all clear
    Reset of router & restarts of router (homehub) over time
    (which included off for more than 15 mins)
    Power off of BT wall device (additional equipment involved with BT set up) and router at same time
    Laptop still slow hard wired to router (as in Ethernet cable from laptop to port on homehub)
    Checked for clean uninstall of Trusteer Rapport software
    (Checked registry which is heart of operating system settings for traces of Trusteer)
    Actually downloaded Trusteer Uninstall ulitility to ensure clean uninstall
    Install of Google Chrome (alternative Internet browser still did not work)
    Uninstall of Google Chrome
    Uninstall of Internet Explorer 9
    Uninstall of Google Desktop
    Uninstall of Mozilla Firefox (alternative browser)
    Also confirmed other laptops (Windows7) & Netbooks experience the same problems

    Hi quinnm5, myself and another poster had replied to your previous thread about the same issue here: http://community.bt.com/t5/BT-Infinity/Broadband-connection-issues/m-p/495109
    If you want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side If the the reply answers your question then please mark as ’Mark as Accepted Solution

  • Firefox does not load web pages but gives no error message

    Hi guys,
    I have been having this problem occasionaly for the past few weeks and can't remember making any changes to my computer or firefox that would have prompted it. Basically what happens is that when I try to load a web page, it says "loading..." at the top of the tab as if it is going to the page, but then nothing happens. It just says "loading..." and never goes to an error message or anything. It will stay like this for hours. I tried clearing the cache and history and it doesn't do anything. Internet explorer works perfectly so I know it's not a network connection problem. When I quit and restart firefox everything works again. It is not specific to any one site, it happens for all sites. I didn't find anything matching my problem on the help pages. Does anyone have any ideas?
    Thanks very much,
    Ben

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you boot, and again when you log in.
    Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
    The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem?
    After testing, reboot as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

  • Trouble loading some web pages but not others

    having a little trouble lately...
    For some reason safari and, well, any other browser, come to think of it isnt work on particular pages.
    Example. The other day google.com wasnt coming up just spinning its wheels then saying:
    Safari can’t open the page “http://google.com/” because it could not connect to the server “google.com”.
    Another example: Safari could not open the page “http://cbgundaker.com/” because the server stopped responding.
    I called my ISP and sat thru 2 hours worth of trouble shooting and got nowhere. They thought it was a DNS issue but I can reach the sites from other machines in the network so it looks like it is only effecting this particular powerbook. I've sat two machines down next to each other and it'll work on one but not the other(same wireless or wired network). annoying.
    Anyone have any ideas?
    Thanks,
    p

    pardon me for butting in, this problem is driving me crazy.
    i just tried your dns thing, no effect.
    what i can't understand is why does my iBook display all 5 pages that i can't display on my iMac? i visit these sites everyday
    -the bookmarks are synced between the two, iBook and iMac use same internet
    -i copied the iBook plist for internet and safari over to my iMac-no change
    -i did all the resets, clear cache, disk utility,ditch plists
    -safari, camino,opera,firefox,shirra do not open these 5 pages
    -macworld.com opens fine, macworld.com/news/ does not
    -my admin account does not display these 5 pages
    -i turned on airport, connected to someone's unprotected network and tried the sites to no avail (i have my own wired internet connection)
    -it hangs on the 2nd to last item in the progress bar, ie "8 out 9 items"
    -this all started sometime after the last security update and before10.4.6
    i am at wits end!

  • I just got a 64 bit new coomputer and use FirFox always. My home page Yahoo an dYahoo email work fine and fill the page but all other websites there is a 3-4' border around the words. What can cause that the 64 bit instead of 32 bit?

    I have tried everything I know in Windows 7 and your suggestions but nothing changes the look of each page. Only about half the page is being used for words and the rest is empty space. As I said my Yahoo and Yahoo email fill the page but nothing else does. Looks like words in a wide picture frame. This is Windows 7....64 bit...4GB memory and 1TB hard drive and Intel 3 chip

    Let me also copy and repeat -- since the developers' club apparently has chosen to not give it any weight or credibility -- a comment by a completely different user, in a different thread:
    "I am using the 64-bit nightly, and it is FAR faster than any release in 32-bit, and I have 2GB of ram. Usually the addon compatibility thing takes minutes, when with the nightly 64-bit, I was done in a matter of seconds. also, I notice that it is faster, pages load faster, there is less lag, and it all around seems better than 32-bit in every aspect, even though it is just automatically compiled and not tweaked."
    So, the developer's club position remains, "there really isn't much need for a 64-bit version", despite comments like that. Hmmm . . .
    Are you SURE you want to stand directly behind that answer, while people shoot at it?

  • IMac will not load web pages, but high speed internet.

    Hi all,
    I upgraded my internet yesterday to 100Mbps, and received a modem + router combo from my ISP (Charter). It is a Netgear CG3000D and I have another router hooked up, which is a Cisco/Linksys E3200. The problem I'm encountering is extremely slow page speeds, it'll take from 3 to 5 minutes for pages to load. My first thought was DNS, but of course I tried Google's Public DNS and OpenDNS. Unfortunately, they did not work. I called both the ISP and router manufacturer, but still no luck. I called Apple, but I'm not paying $49 for additional support. I'm assuming my Mac is caching something it's not supposed to. I do not live near an Apple store to see what's wrong. I went into safe mode and the issue still hasn't been resolved. There's multiple devices working fine, and I've noticed when my Mac is connected to my router, my PC goes haywire as well. And FYI -- I connected my iMac directly to the ISP's modem/router and it didn't work either.
    Internet/Cable > Netgear CG3000D > Cisco/Linksys E3200 > iMac
    Please help! Much appreciated.
    Take care,
    Tyler

    Run through this list of fixes
    WiFi, Internet problems, possible solutions

  • Firefox won't load any web pages but my other browser will

    i updated to firefox beta. It ran for one day. Since then it loads a blank white page and won't go to any web sites. I don't get an error message or anything. It just sits there.

    http://support.mozilla.com/en-US/kb/Firefox%20cannot%20load%20websites%20but%20other%20programs%20can?s=won%27t+load+pages&r=2&as=s
    This was the problem with mine. I had to remove mozilla firefox from my trusted programs in my antivirus firewall settings and then open firefox... it added it back in. The problem occured when my AVG updated.

  • ITunes match does not work on my iPhone 4S, but is working across all of my other Macs and iOS devices.  All other iCloud services are working fine on the 4S - any suggestions?

    iTunes match is not working on my iPhone 4S; it works awesome across all of my Macs and other iOS devices (iPad 2, iPod Touch 4g x 2, and my wife's iPhone 4).  Any suggestions?  Thanks!

    It is not possible to "toggle back and forth" at will. If you associate a device with an Apple ID and you have iTunes Match enabled you must wait 90 days before you can associate it with another Apple ID. See this Apple KB article for more information: http://support.apple.com/kb/HT4627

  • I'm using Safari 5.0.5 on a 13" MacBook Pro and can't get Safari to fully load web pages or pictures on web pages. Any suggestions?

    I bought a MacBook Pro in October of 2010 and it's been running greatly up to this month. Now I am experiencing problems with Safari loading web pages. Sometimes it will load web pages just fine and other times it doesn't load web pages at all. This only seems to happen with certain sites. Also, on some web pages Safari won't load pictures (only the blue "?" is visible). I've experienced the same problem when I use the Mac App Store. In addition to these problems, when I visit sites that have problems loading, sometimes I just get a notice saying "Not connected to the internet" or "Safari cannot find the server." I am beginning to wonder if the problem could be some setting with my wireless router. I'm really hoping my MacBook hasn't gotten a virus. Any help would be greatly appreciated.

    Hi.
    Try putting these numbers in Network>TCP/IP>DNS Servers, for the Interface you connect with...
    208.67.222.222
    208.67.220.220
    Then Apply

  • Safari, camino, firefox not opening web pages but IE does... any ideas why?

    i just recently moved from the US to Bosnia. after finaly getting high speed internet, i'm finding that some web pages on my macbook pro open incredibly slow or not at all while those same web pages open just fine on my pc using internet explorer. i've tried using camino and firefox in addition to safari and all have the same problem on the mac.
    does anybody have any ideas?????

    well friend, thanks again for all your help. i found a lot of help on another thread if you're interested: http://discussions.apple.com/thread.jspa?threadID=1195713&tstart=0
    regardless, here's some things i did that seem to have helped for now... significantly speeding up my web browsing:
    1. I changed from WPA/WPA 2 to just WPA 2 (this seemed to have helped the most)
    2. I added two 'general' DNS addresses in my preferences/network settings (this also seemed to help):
    208.67.222.222
    208.67.220.220
    3. under my preferences/network settings, I completely turned off Configure IPv6. (I don't know if this has helped but it was suggested and it doesn't seem to have hurt)
    Unless I'm connected to a cisco client, I still have very slow to no browsing on the apple discussions pages but all other pages seem to be working now without cisco.
    until next time.

  • Firefox will not print a web page but other programs will.

    Firefox will not print a web page but my other browser will print it. It activates the printer and shows the page frame but does no printing of the page.
    == This happened ==
    Every time Firefox opened
    == About two months ago.

    Ever since the last Firefox update, I have been unable to use my printer while in Mozilla, but it works with Internet Explorer.

  • HP Officejet PRO 8500A Plus...can"t print wirelessly from web...all other wireless prints ok

    HAD TO REINSTALL MY PRINTER SOME TIME AGO.....NOW I CAN'T PRINT FROM WEB...ALL OTHER WIRELESS PRINT REQUESTS WORK FINE.  DO I NEED TO ENABLE SOMETHING TO GET THIS TO WORK?  WHEN I FIRST INSTALLED MY PRINTER EVERYTHING WORKED FINE....OBVIOUSLY I MESSED UP SOMETHING IN THE RE-INSTALL?

    Please reload the drivers and software on the Win7 PC.  Reconfigure and try again. 
    Say thanks by clicking the Kudos Thumbs Up to the right in the post.
    If my post resolved your problem, please mark it as an Accepted Solution ...
    I worked for HP but now I'm retired!

  • Serious delay in loading web pages, not network,  but  safari issue

    After my last software update, I am experiencing delays in loading web pages, 30sec-minutes on safari. This occurs rather frequently, I'd say about 20%-30% of the times I visit certain web pages.
    One example web location I noticed this happening is (but its not the only one):
    http://www.theweathernetwork.com/weather/caqc0363
    Once I visit this page, sometime it loads fine, other times it takes forever (the load indicator stays on in the tab). Also, once the delay occurs, opening up new widows or new tabs to ANY other address are also delayed. It seem like all of safari is stuck waiting for responses. (safari itself is still running ok, it is responsive and there is NO spinning wheel of death).
    It is not a network issue. Often while waiting for safari to load, I launch firefox, visit the same page and read, meanwhile Safri still loading, even after trying to refresh...I also do other network tasks, ssh, ftp, email with no problem.

    Thanx! The numbers didn't help me anything, but your post reminded me: I found the DNS numbers that my ISP had provided that I had put in the Ethernet TCP/IP section in Network Preferences, and just copied and pasted them into my airport TCP/IP section. Worked great!

Maybe you are looking for

  • "File Dialog" Express VI returns the wrong path when the user selects the desktop

    In labview 8.0.1 with Windows XP, the File Dialog Express VI seems to return something other than the path selected by the user when configured to browse for folders (or files and folders) and the user selects the desktop. I can't determine exactly w

  • In logman, should All Instances include _Total?

    Hello If this question has already been asked and answered elsewhere, my apologies. I want to collect IIS worker process perfmon data using logman.  When I add counters in PerfMon, choosing All Instances gives all instances (each w3wp process for eac

  • Is there a way to test NIVLM using a dummy license file?

    we are testing a situation where an autocad install (Flexlm) crashes a nicely running VLM install. we wan to test this on another server using a dummy license file. just to keep away from the Live environment. Can this be done? ruud  Solved! Go to So

  • Odd outbound longdistance issue

    I have a T1 on a 2851 that for some long distance calls will pass 10 digits to the provider but for others will pass only the first 7 digits.... I am out of ideas.... dial-peer voice 200 voip destination-pattern 6... progress_ind setup enable 3 sessi

  • Duplicates of elements for Address Book entries

    I have looked through the various threads that discuss "duplicate" entries in Address Book (Contacts). My situation is a slight variation. While I have a handful of AB people who have multiple entries (some have as many as 15!), my problem here is th