EA6350 usb storage problems

I have a WD Mybook 3tb drive setup as my usb storage, and it is very unreliable. At times it works fine, but is unusble a large majority of the time. As in, it can't access a single file on the drive. It doesn't seem to be related to access either, as it sometimes happens under heavy usage, other times accessing a file at a time. The drive had no problems when plugged into a computer.
All of my settings are default, no secure access, no media server or ftp server, no media prioritization.

I recommend trying this, it maybe trying to catalog that size of information and may take a while. Do a reset sometime at night before you go to bed, Set up the router again and enable the drive on the router. Let the router and the drive be alone over night and check back in the morning. Let the router do it's cataloging of the drive. It should be done by morning. Look at the drive light in the morning. If it's still blinking, the router maybe still accessing the drive and it's contents. 
The more you put on the drive the longer it may take the router to catalog the drive and it's contents. I personally don't use USB drives on the router unless they are small drives. I prefer using wired LAN NAS for any storage solutions. 

Similar Messages

  • WRT600N USB Storage Problems Solved

    For a couple of years, I've been living with all the problems others have reported with the WRT600N USB storage - lost connections, permissions problems, rebooting the router to recover access to the USB drive, etc. I solved my problems, mostly, by switching to a DLink DIR-655 router. I assume other routers in the Dlink family that support USB devices will perform similarly.
    My main problem seemed to be interference from the microwave, which is in an open kitchen/keeping room arrangement in my house. However, the bottom line is that any time I lost wireless connectivity to the router, due to the microwave or unknown causes, I'd lose access to the USB drive. This meant a trip upstairs to power cycle the router and the USB drive several times a day.
    With the Dlink, I still sometimes lose wireless connectivity due to the microwave or unknown causes, but not as often. Sometimes, but not always, this will cause me to lose the USB drive access. If I do need to reboot the router, I can do so from the web based interface, something that was not possible with the WRT600N, so no more trips upstairs to perform this operation. I also find have a stronger wireless signal in my work location with the Dlink.
    Dlink uses a SharePort software utility to manage the USB connection and this has to be installed on all PC's that want access to the USB device. SharePort makes a USB device appear to be a local device attached directly to the computer you're using and you can attach external drives/printers/probably USB hubs. (I've experimented only with an external USB drive.) Because of this, however, only one computer can attach to the USB device at a time - not a problem for me, but you need to be aware. The software has a mechanism for requesting access to the USB device from one computer, when the device is in use by another computers. You can also set it to automatically connect to the USB device if its available, to try a reconnect if connection is lost, and to automatically run a program when the USB device connects. Dlink says SharePort will support FAT or NTFS formatted drives and there's no known limitation on the drive size.
    Dlink support doesn't seem much better than here - it took about three weeks for me to get an answer on the external drive size and formatting options. There are plenty of complaints on the Dlink support site about poor support, poor performance of SharePort, etc.  So, all I can say is their router/USB device sharing has worked much better for me than my Linksys WRT600N ever worked.

    Welcome to the WRT600N nightmare. The Storage Link is poorly documented, and the firmware controlling it has issues. Basically, it will corrupt file date/times stamps whenever you copy files onto the attached drive. It has also been known to be a bit flaky about maintaining the drive as a connected/mapped drive. Backup programs may have difficulty accessing the drive via Storage Link. Depending on the file format you use, you may encounter file size limitations on the Storage Link drive.
    I, personally, gave up after a few days of these issues mentioned above and bought extra USB hard drives for each computer in the house rather than try and use the Storage Link as a NAS.
    What O/S are you using on your computer? I can try and walk you through the setup.
    A+ Certified, over 15 years of hands on computer and home networking experience...and I still get lost!

  • EA4500 USB storage problem

    I have ea4500 with the latest avaiable firmware. smart wi fi, I have tried several USB pens and hard disk  but I cannot save a file over 3.1 mb to to the shareport device. the routers main page shows the correct storage space available, but the computer always shows 3.1 mb available  I can access files saved on the stick no problem, but i cannot add files
    osx mountain lion, all Usb storage device are formatted to FAT 
    please help me I'm desperate!!!

    Are you having the same issue saving files using other computers? Check if this is the case and use a windows- based computer for isolation. Is Secure Folder Access ON and have you set authorized users for your storage device? You might be using a log-in that only has read access as you are not able to add files. See Tested HDD and Printers for the EA4500. These devices are guaranteed to work with the EA4500. If your drive is not on the list, there is a slim chance that the storage feature will not work (properly).

  • E3000 USB Storage Problem

    Hey,
    Just setup my E3000 router and all was good.
    Connected a FAT formatted HHD to it and all went well.
    Disconnected the HDD and uploaded my music and movies.
    When I connect the drive and click the "Create Share" button, the dialog comes up as normal but when I hit the "Submit" button the browser shows me this message:
    "Unable to load the webpage because the server sent no data."
    As if I have lost connection to the router. For about a minute or two I can't access the router.
    Any ideas? I'm on Mac OS X 10.6.7 if that makes any difference.
    Thanks guys!

    I think you can try to reset the router and reconfigure it.
    Press and hold the reset button on the router for 30 seconds. Release the reset button and wait for 30 seconds. Power cycle the router and reconfigure it.
    Follow this link to configure the USB storage connected to the router.

  • Lennovo A1 " Turn on USB storage problem"

    Hi Lenovo community..
    I just want to ask if you could help me resolve this issue. When I connect my A1 tablet on any pc for file transfer. the "Turn on USB Storage " just keep on spinning. When I tilt the screen the "Turn on USB storage" spears and same result. It keeps on spinning.
    Sometimes my pc detects the tablet but I can't open the local disk assigned.
     Please help me

    Hi
    Welcome To Lenovo Community
    You may need to install the correct drivers for USB
    http://www.tinybeetle.us/A1_USB_Driver_20110816.zi​p
     Extract that to a folder and then point windows to that folder when it does the driver search.
    http://forums.lenovo.com/t5/IdeaPad-IdeaTab-Slate-​Tablets/Ideapad-A1-Windows-7-USB-Connection/m-p/59​...
    Hope This Helps
    Cheers!!!
    Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
    Did someone help you today? Press the star on the left to thank them with Kudos!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!  This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • WRT 160nl USB Storage Problems

    Hi, just got the 160nl recently.
    My problem is with my 1TB Maxtor Touch (NTFS). It works well for 20min, when connected to the USB point in the router. But after that, the response of the drive is slow, streaming becomes choppy, and then eventually the drive is no longer visible.
    My PC is connected with a ethernet cable. I've upgraded to the latest firmware. I've done reboots, resets, but it still works for 30 min and then later it stops responding.
    Anyone else facing problems like mine?

    Try to reset and reconfigure the router as you have the firmware upgraded .
    Also if you have any other Hard Drive try connecting that and see if the same thing happens .
    What is the current firmware version on your router ?

  • USB Storage problem

    Hi
    I want to mount my usb stick but I'm not able myself, so I'll ask you help
    Here's my hwd -ec output of the usb stick:
    USB Mass Storage
      unknown         : Dell Memory Key
    the module is unknown and here the dmesg:
    usb 4-6: new high speed USB device using ehci_hcd and address 5
    Could you help me please? Thanks!
    - tompouceuh

    ar 25 13:44:00 lmek usb 4-6: new high speed USB device using ehci_hcd and address 6
    Mar 25 13:44:00 lmek scsi1 : SCSI emulation for USB Mass Storage devices
    Mar 25 13:44:05 lmek Vendor: M-SysT5   Model: Dell Memory Key   Rev: 5.00
    Mar 25 13:44:05 lmek Type:   Direct-Access                      ANSI SCSI revision: 00
    Mar 25 13:44:05 lmek SCSI device sda: 123903 512-byte hdwr sectors (63 MB)
    Mar 25 13:44:05 lmek sda: Write Protect is off
    Mar 25 13:44:05 lmek SCSI device sda: 123903 512-byte hdwr sectors (63 MB)
    Mar 25 13:44:05 lmek sda: Write Protect is off
    Mar 25 13:44:05 lmek /dev/scsi/host1/bus0/target0/lun0: p1
    Mar 25 13:44:05 lmek Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
    and penguin:
    [root@lmek dev]# modprobe sd_mod
    FATAL: Module sd_mod not found.
    (and if you want to help me more,
    I have some others questions:
    I can play my mov files on kaffeine but I don't have sound. Every others filetypes have sounds so what am I suppose to understand?
    And the last:
    My partitions from fstab are always mounted for root only I'm always obligated to do a umount in root, and mount in my user shell to access my data from my partitions.
    Here's my fstab:
    /dev/discs/disc0/part1 /mnt/windows vfat defaults,rw,user 0 0
    /dev/discs/disc0/part2 /mnt/things vfat defaults,rw,user 0 0
    ) Thanks a lot again!
    Thanks for helping me!

  • EA6300 USB Storage problem

    Hello,
    Im trying to map a network drive, connected to my EA6300 with Read and Write permissions. I have secure folder enabled. I also changed the password of the Guest access so that im sure the PC doesnt log in with Guest/Guest. So What i do is i map a new network drive, select to log in with different credentials and then just enter the admin / my password. The PC maps the drive and i can copy files onto it, but i cant delete or move. 
    Please advise.
    Thanks and regards
    G.

    Hi there, gnovodvorsky. I'd like to know more about this, it's quite interesting since I was able to delete and move the files on my mapped drive. Can you post pictures on where you get the error if possible? Let's have other users join the fray. They may have aces up their sleeves we don't know about. Cheers!
    Help, learn and share

  • [solved] USB storage devices problem

    Hello everyone. I have MSI Wind U270 and recently I've moved from Ubuntu 11.04 to Arch. I really like Arch so far but I have one quite big problem and I can't find any solution, so I hope someone here could help me.
    After I'd installed Arch, I tried to copy some file from/to USB flash drive. After just few seconds, transfer failed with information about I/O errors and USB flash drive disappeared along with any other USB drives connected at the same time but logitech usb mouse and keyboard continue to work.
    My first thought was that it's simply broken USB drive, but same thing was happening also when I tried to move some files from/to any other USB storage device that I have.
    Here is sample dmesg output after I connect device:
    [ 4799.189720] usb 1-2: new high-speed USB device number 4 using ehci_hcd
    [ 4799.369911] xhci_hcd 0000:06:00.0: PME# disabled
    [ 4799.369935] xhci_hcd 0000:06:00.0: setting latency timer to 64
    [ 4799.399707] ehci_hcd 0000:00:13.2: BAR 0: set to [mem 0xfeb48000-0xfeb480ff] (PCI address [0xfeb48000-0xfeb480ff])
    [ 4799.399754] ehci_hcd 0000:00:13.2: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00013)
    [ 4799.399800] ehci_hcd 0000:00:13.2: PME# disabled
    [ 4799.399819] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [ 4799.426731] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    [ 4799.520213] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    [ 4799.690262] usbcore: registered new interface driver uas
    [ 4799.704107] Initializing USB Mass Storage driver...
    [ 4799.704420] scsi7 : usb-storage 1-2:1.0
    [ 4799.704959] usbcore: registered new interface driver usb-storage
    [ 4799.704966] USB Mass Storage support registered.
    [ 4801.166512] scsi 7:0:0:0: Direct-Access JetFlash Transcend 8GB 1100 PQ: 0 ANSI: 0 CCS
    [ 4801.168550] sd 7:0:0:0: [sdc] 15826944 512-byte logical blocks: (8.10 GB/7.54 GiB)
    [ 4801.169401] sd 7:0:0:0: [sdc] Write Protect is off
    [ 4801.169411] sd 7:0:0:0: [sdc] Mode Sense: 43 00 00 00
    [ 4801.170332] sd 7:0:0:0: [sdc] No Caching mode page present
    [ 4801.170340] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 4801.175736] sd 7:0:0:0: [sdc] No Caching mode page present
    [ 4801.175747] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 4801.176962] sdc: sdc1
    [ 4801.181454] sd 7:0:0:0: [sdc] No Caching mode page present
    [ 4801.181465] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 4801.181471] sd 7:0:0:0: [sdc] Attached SCSI removable disk
    [ 4801.388155] xhci_hcd 0000:06:00.0: PME# enabled
    [ 4801.439601] ehci_hcd 0000:00:13.2: PCI INT B disabled
    [ 4801.439657] ehci_hcd 0000:00:13.2: PME# enabled
    [ 4801.519628] ohci_hcd 0000:00:12.0: PCI INT A disabled
    [ 4802.346484] ohci_hcd 0000:00:13.0: PCI INT A disabled
    and when I start to copy some things to/from USB device this is what's happening:
    [ 4981.389262] ehci_hcd 0000:00:12.2: force halt; handshake ffffc90000c1e024 00004000 00000000 -> -110
    [ 4981.389271] ehci_hcd 0000:00:12.2: HC died; cleaning up
    [ 4981.389377] usb 1-2: USB disconnect, device number 4
    [ 4981.399810] sd 7:0:0:0: [sdc] Unhandled error code
    [ 4981.399820] sd 7:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
    [ 4981.399826] sd 7:0:0:0: [sdc] CDB: cdb[0]=0x2a: 2a 00 00 1f b4 7e 00 00 08 00
    [ 4981.399840] end_request: I/O error, dev sdc, sector 2077822
    [ 4981.399850] Buffer I/O error on device sdc1, logical block 259720
    [ 4981.399854] lost page write due to I/O error on sdc1
    [ 4981.404451] sd 7:0:0:0: [sdc] Unhandled error code
    [ 4981.404461] sd 7:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
    [ 4981.404467] sd 7:0:0:0: [sdc] CDB: cdb[0]=0x2a: 2a 00 00 20 34 7e 00 00 f0 00
    [ 4981.404481] end_request: I/O error, dev sdc, sector 2110590
    [ 4981.404489] Buffer I/O error on device sdc1, logical block 263816
    [ 4981.404493] lost page write due to I/O error on sdc1
    [ 4981.404500] Buffer I/O error on device sdc1, logical block 263817
    [ 4981.404504] lost page write due to I/O error on sdc1
    [ 4981.404509] Buffer I/O error on device sdc1, logical block 263818
    [ 4981.404512] lost page write due to I/O error on sdc1
    [ 4981.404517] Buffer I/O error on device sdc1, logical block 263819
    [ 4981.404521] lost page write due to I/O error on sdc1
    [ 4981.404525] Buffer I/O error on device sdc1, logical block 263820
    [ 4981.404529] lost page write due to I/O error on sdc1
    [ 4981.404534] Buffer I/O error on device sdc1, logical block 263821
    [ 4981.404537] lost page write due to I/O error on sdc1
    [ 4981.404543] Buffer I/O error on device sdc1, logical block 263822
    [ 4981.404546] lost page write due to I/O error on sdc1
    [ 4981.404550] Buffer I/O error on device sdc1, logical block 263823
    [ 4981.404554] lost page write due to I/O error on sdc1
    [ 4981.444899] usb 1-4: USB disconnect, device number 3
    Next I thought – computer is broken. But it simply couldn't be true because in Ubuntu it's working.
    I wanted to test if USB transfer is working in other distros, so I downloaded few and tried:
    Ubuntu 11.04 – everything is working
    Ubuntu 11.10 – it's not working, exactly same errors as in Arch
    Ubuntu 12.04 Alpha 2 – it's not working
    Mint 11 – it's working
    Mint 12 – it's not working
    So one thing in common that I can think of is fact that USB transfer is working in distros using kernel <3.0 and is broken in those using kernel >=3.0.
    In dmesg output I can see ehci_hcd errors. When I remove this module before moving files, than everything is working fine apart from very slow transfer but it's obvious.
    I really hope that someone will be able to help with my problem.  I don't know if it's some bug or it's just some configuration error.
    EDIT: problems were caused by rts5139 module (card reader). Blacklisting that module solved all the problems.
    Last edited by wpb (2012-07-01 08:37:02)

    Ok,  so here is part of /var/log/messages.log with failed USB transfer:
    Feb 28 20:21:40 localhost kernel: [ 117.263584] usb 3-2: new high-speed USB device number 4 using ehci_hcd
    Feb 28 20:21:40 localhost mtp-probe: checking bus 3, device 4: "/sys/devices/pci0000:00/0000:00:12.2/usb3/3-2"
    Feb 28 20:21:40 localhost kernel: [ 117.470130] ehci_hcd 0000:00:13.2: BAR 0: set to [mem 0xfeb48000-0xfeb480ff] (PCI address [0xfeb48000-0xfeb480ff])
    Feb 28 20:21:40 localhost kernel: [ 117.470251] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    Feb 28 20:21:40 localhost kernel: [ 117.546266] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    Feb 28 20:21:40 localhost mtp-probe: bus: 3, device: 4 was not an MTP device
    Feb 28 20:21:42 localhost kernel: [ 119.687034] usbcore: registered new interface driver uas
    Feb 28 20:21:42 localhost kernel: [ 119.692675] Initializing USB Mass Storage driver...
    Feb 28 20:21:42 localhost kernel: [ 119.693029] scsi7 : usb-storage 3-2:1.0
    Feb 28 20:21:42 localhost kernel: [ 119.694285] usbcore: registered new interface driver usb-storage
    Feb 28 20:21:42 localhost kernel: [ 119.694294] USB Mass Storage support registered.
    Feb 28 20:21:43 localhost kernel: [ 120.353657] ohci_hcd 0000:00:13.0: PCI INT A disabled
    Feb 28 20:21:43 localhost kernel: [ 121.110815] scsi 7:0:0:0: Direct-Access JetFlash Transcend 8GB 1100 PQ: 0 ANSI: 0 CCS
    Feb 28 20:21:43 localhost kernel: [ 121.115125] sd 7:0:0:0: [sdc] 15826944 512-byte logical blocks: (8.10 GB/7.54 GiB)
    Feb 28 20:21:43 localhost kernel: [ 121.117132] sd 7:0:0:0: [sdc] Write Protect is off
    Feb 28 20:21:43 localhost kernel: [ 121.125243] sdc: sdc1
    Feb 28 20:21:43 localhost kernel: [ 121.130244] sd 7:0:0:0: [sdc] Attached SCSI removable disk
    Feb 28 20:21:44 localhost kernel: [ 121.570240] ehci_hcd 0000:00:13.2: PCI INT B disabled
    Feb 28 20:21:44 localhost ntfs-3g[1936]: Version 2012.1.15 external FUSE 28
    Feb 28 20:21:44 localhost ntfs-3g[1936]: Mounted /dev/sdc1 (Read-Write, label "", NTFS 3.1)
    Feb 28 20:21:44 localhost ntfs-3g[1936]: Cmdline options: rw,nosuid,nodev,uhelper=udisks,uid=1000,gid=1000,dmask=0077,fmask=0177
    Feb 28 20:21:44 localhost ntfs-3g[1936]: Mount options: rw,nosuid,nodev,uhelper=udisks,allow_other,nonempty,relatime,fsname=/dev/sdc1,blkdev,blksize=4096,default_permissions
    Feb 28 20:21:44 localhost ntfs-3g[1936]: Global ownership and permissions enforced, configuration type 1
    Feb 28 20:22:11 localhost kernel: [ 148.692914] usb 3-2: USB disconnect, device number 4
    Feb 28 20:22:11 localhost kernel: [ 148.756937] sd 7:0:0:0: [sdc] Unhandled error code
    Feb 28 20:22:11 localhost kernel: [ 148.756947] sd 7:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
    Feb 28 20:22:11 localhost kernel: [ 148.756954] sd 7:0:0:0: [sdc] CDB: cdb[0]=0x2a: 2a 00 00 1e 2f f6 00 00 18 00
    Feb 28 20:22:11 localhost kernel: [ 148.756983] lost page write due to I/O error on sdc1
    Feb 28 20:22:11 localhost kernel: [ 148.757000] lost page write due to I/O error on sdc1
    Feb 28 20:22:11 localhost kernel: [ 148.757016] lost page write due to I/O error on sdc1
    Feb 28 20:22:11 localhost kernel: [ 148.761894] sd 7:0:0:0: [sdc] Unhandled error code
    Feb 28 20:22:11 localhost kernel: [ 148.761905] sd 7:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
    Feb 28 20:22:11 localhost kernel: [ 148.761911] sd 7:0:0:0: [sdc] CDB: cdb[0]=0x2a: 2a 00 00 1e 2f ae 00 00 08 00
    Feb 28 20:22:11 localhost kernel: [ 148.761939] lost page write due to I/O error on sdc1
    Feb 28 20:22:11 localhost kernel: [ 148.914173] usb 3-4: USB disconnect, device number 3
    Feb 28 20:22:24 localhost ntfs-3g[1936]: ntfs_attr_pread_i: ntfs_pread failed: Input/output error
    Feb 28 20:22:24 localhost ntfs-3g[1936]: Reading $BITMAP failed: Input/output error
    Feb 28 20:22:24 localhost ntfs-3g[1936]: Failed to allocate clusters: Input/output error
    Feb 28 20:22:24 localhost kernel: [ 161.862408] quiet_error: 2 callbacks suppressed
    Feb 28 20:22:24 localhost kernel: [ 161.862424] lost page write due to I/O error on sdc1
    Feb 28 20:22:24 localhost kernel: [ 161.862436] lost page write due to I/O error on sdc1
    Feb 28 20:22:24 localhost kernel: [ 161.862446] lost page write due to I/O error on sdc1
    Feb 28 20:22:24 localhost kernel: [ 161.862457] lost page write due to I/O error on sdc1
    Feb 28 20:22:24 localhost kernel: [ 161.862466] lost page write due to I/O error on sdc1
    Feb 28 20:22:24 localhost kernel: [ 161.862476] lost page write due to I/O error on sdc1
    Feb 28 20:22:24 localhost kernel: [ 161.862485] lost page write due to I/O error on sdc1
    Feb 28 20:22:24 localhost kernel: [ 161.862495] lost page write due to I/O error on sdc1
    Feb 28 20:22:24 localhost kernel: [ 161.862505] lost page write due to I/O error on sdc1
    Feb 28 20:22:24 localhost kernel: [ 161.862514] lost page write due to I/O error on sdc1
    Feb 28 20:22:24 localhost ntfs-3g[1936]: Unmounting /dev/sdc1 ()
    and here is complete /var/log/messages.log - I just started system and then tried to copy some files to USB drive:

  • Yoga tablet 2 1050 problem to connect to my pc as usb storage

    when i connect my yoga to my pc (win7) it sees as CD with lenovo suite.but i cant install it.when i start intalling lenovo suite nothing happens on my tab there are only 2 options MTP and PTP (there is also ADB) but there is not as usb storage so i cant copy files via usb from my pc directly

    Any videos copied to the internal drive play fine, the same video copied to SD card will not play. This problem is all related to the SD card and can now be closed.

  • Problem about EA6700 USB Storage

    I am using a USB2.0 disk on the EA6700(plug in the usb2.0 slot of the router).
    I can copy file to the usb disk from computer and play movie file on computer directly from the usb disk.
    But when I want to delete the file in the usb disk. The windows7 system pop up an alert said I need some kind of authority to delete the file.(the file that I just copy into usb disk from computer few minutes ago)
    The alert window shows:You need the Linksys\admin authority to delete this file.
    But sometimes the alert is:You need the Unix User\admin authority to delete this file.
    So I go to check the router config.
    USB Storage > Folder Access > Secure Folder Access(already turned ON) and there are 2 authorized users:admin(read & write) and guest(read only)
    USB Storage > FTP Server(already turned ON) and "FTP Port 21" and "Encoding UTF-8"
    USB Storage > Media Server(already turned ON)
    Now I have to plug in the usb disk on computer when I want to delete file.
    How can I directly delete it when it`s on the router?How can I have the authority?
    Thanks very much!

    You may want to contact Microsoft on how to create a login account in your computer. Make sure that the router's Folder and File Sharing was configured properly. Check this link to know more about the USB storage options of the router:
    http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=f2fd60559043499c8643c3deea7c8ede_Overview_of_the_U...

  • EA6400 Problem FTP USB Storage

    When I do not restrict the acces to the files I can reach them by FTP
    When I do restrict the acces I can not reach them anymore
    After usin my login I got this screen
    Like you see: the Transcend is not visible.
    Yes I have the rights to see and write on the USB Storage.
    Anybody a suggestion?
    Solved!
    Go to Solution.

    Use Username: admin and Password: the router password (admin by default). Don't use your Linksys Smart WiFi account password.
    Are you able to access the drive locally using the Remi user? Did you made sure that you checked the Transcend share when you created the Remi user?
    Try Chadster's suggestion by creating a new user and clear the browser. Or you can try using another computer.

  • My new iPhone 5 won't connect to iTunes, and when I connect to my computer it comes up as a usb storage device, also in the phone itself under usage it shows internal memory of 2gb and sd card 64 gb, is this an original iPhone or have I been sold a copy

    My new iphone 5 can not connect to itunes, it comes up as a usb storage device when I plug it in, also in the phone under settings/usage it shows internal memory of 2gb and SD card of 64gb, I cannot get it to connect to itunes at all so cannot sync etc, is this a genuine Iphone or a copy. I have owned 4 iphones and never had a problem with connecting to iphones and restoreing to a backup.

    According to http://en.wikipedia.org/wiki/IPhone_5
    the iPhone5 has 1GB of RAM, and internal storage of 16, 32, or 64GB.
    It does not use SD cards.
    Fake iphones are really Android phones using the skin of iOS6.
    Click on the App Store icon. If it takes you to Apple's App Store, then it's a real iPhone.
    But if you are directed to Google Play, then I'm afraid you've gotten a copy.

  • I am trying to add music to my computer and then put it on a usb storage device

    ok i havent used a computer in a very long time and the last time i did things seemed a whole lot easier.  i got a new laptop for valentines day and i still aint figured this thing out. what i am trying to do is add all my music cds to my computer, make some playlists, then download the music to a usb storage device so i can have the music in my truck.
    when i put a cd in my computer it pops up and it starts playing but i have no clue as what to do next. i have tried to make a playlist through the player that pops up and plays the music but aint having any luck. IM CLUELESS!!!! nothing ive tried has wroked, i need help please.
    thank you in advance

    Hi,
             The below link shows how to create playlist in Itunes.  Once the playlist is created, if you are using apple Ipod or any other apple product. Then once you connect the device it will start the sync with the device and then you can start playing.
    http://support.apple.com/kb/PH12340
    If you are using another device, then please do mention the device to which you want to sync the music and which player are using on the system.
    "I work for HP."
    Please click the "White Kudos" star to say thanks for helping.
    Please mark "Accept As Solution" if my help has solved your problem.

  • USB storage devices not being recognised

    Product:
    13" Macbook Pro w/ Retina Display (Late 2013 model)
    OS X Yosemite (version 10.10.2)
    2.4GHz i5, 8gb 1600 MHz DDR3, 256gb HDD
    Issue:
    - macbook unable to recognise USB storage devices.
    - can be found on disk utility but 'greyed out'.
    - cannot be found under devices in finder.
    - tried restarting laptop, no effect.
    - additional storage via Nifty + 64gb micro SD is working fine.
    - apple products (iPod/iPhone/iPad) and printer/scanner working fine, only storage devices appear to be affected.
    - USB-ethernet adapter appears to be working w/o problems too.
    - last technical thing done to the computer was SMC reset 5 days ago for power cable light not working properly (fixed with reset).
    Hello everyone,
    I seem to having some issues with my macbook and the ability to use USB storage devices. The SD card slot appears to be working fine as I have a nifty device attached on. I'm not sure exactly when this started to happen but it was working last week for sure.
    I've put some succinct notes above for anyone who is willing to help out and is able to use it to determine the problem but I don't think it's a hardware issue. Maybe it's a bug with the new OS X update over the weekend?
    I've attached a screenshot of the disk utility below as well.
    If anyone could help me out then that would be greatly appreciated.
    Thanks in advance!

    Some users on another Apple thread had success in running Kext Utility last November with similar issues.
    I ran kext utility 2.6.1, restarted my computer and everything was working again.

Maybe you are looking for