EA6500 DLNA media server MP3 not shown

Hi!
I have recently bought Linksys EA6500 router and attached a USB drive with some media (4000+ MP3 files, 7000+ photos, and 1000+videos). Everything works smoothly, even from Nexus 4 on wireless, but none of the MP3 files are showing up! Are there any known limitations in Twonky server (which this device apparently uses) in terms of naming files, subdirectory structure, anything? I tried rescanning the drive, although didn't try rebuilding database...
Any ideas?
Solved!
Go to Solution.

Hi, 
Yes. There's a known limitation with Twonky Media Server that's built-in with your router: "maxfile-8000" - the license with Twonky limits the # of files to be scanned to 8000. This issue had been raised before and some acceptable reason is the "amount of cpu and ram need to deal with the db in memory" - of course, these routers have way much lower hardware specs, even compared to a smartphone running on Android 2.3.6 OS.
Here's the thread that was raised before: 
http://community.linksys.com/t5/Wireless-Routers/E4200-v2-Twonky-Media-Server-Issue-Default-quot-max...
Here are the links from Twonky Community Forum: 
http://community.twonky.com/twonky/topics/limit_8000_files
http://community.twonky.com/twonky/topics/twonky_media_server_issue_with_cisco_ea4500_router_and_wd_...
http://community.twonky.com/twonky/topics/cisco_e4200_default_maxitems_is_8000
Hope this helps.
If everyone needs to believe in something, I believe I'll have another beer..

Similar Messages

  • DLNA Media Server is not showing on diffrent Vlans

    Hi all,
    i have a media Server in one Vlan now i want to access it from other Vlans as well. for DLNA i configure Multicast and PIM Spare mode with rp address on Cisco 4500x L3 switch and enable IGMP snooping on all my Layer 2 switches but still not able to show my DLNA in other Vlans
    DLNA in Vlan2
    want to show in it in Vlan3 and Vlan4
    here is my L3 Switch configuration foe PIM
    ip routing
    ip multicast-routing
    int vlan 2
    ip add 192.168.2.1 255.255.255.0
    ip pim sparse-mode
    int vlan 3
    ip add 192.168.3.1 255.255.255.0
    ip pim sparse-mode
    int vlan 4
    ip add 192.168.4.1 255.255.255.0
    ip pim sparse-mode
    ip pim rp-address 192.168.2.1

    sh ip mroute 239.255.255.250
    IP Multicast Routing Table
    Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
           L - Local, P - Pruned, R - RP-bit set, F - Register flag,
           T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
           X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
           U - URD, I - Received Source Specific Host Report,
           Z - Multicast Tunnel, z - MDT-data group sender,
           Y - Joined MDT-data group, y - Sending to MDT-data group,
           G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
           Q - Received BGP S-A Route, q - Sent BGP S-A Route,
           V - RD & Vector, v - Vector
    Outgoing interface flags: H - Hardware switched, A - Assert winner
    Timers: Uptime/Expires
    Interface state: Interface, Next-Hop or VCD, State/Mode
    (*, 239.255.255.250), 16:39:10/00:02:57, RP 192.168.2.1, flags: SJC
      Incoming interface: Null, RPF nbr 0.0.0.0
      Outgoing interface list:
        Vlan2, Forward/Sparse, 00:27:03/00:02:56
        Vlan3, Forward/Sparse, 02:08:20/00:02:56
        Vlan4, Forward/Sparse, 12:20:31/00:02:57

  • EA6900 DLNA Media Server update intervall

    Hi everyone,
    I have the problem, that the media server does not update within the setted intervall. I set it up to scan the folders every 2 hours, but i updates the folder only every day or even less.
    For example - I made this screenshot today, October 16 - 10 a.m. (I am writing from Vietnam - so don´t wonder about the dates)
    So i played around withe the settings - 6hr/12hrs - no change.
    We use the DLNA Server for Samsung Smart TVs - so it is important, that it will update regulary.
    Anyone has an idea, what could be the problem?

    already did when I bought the router - so firmware should be the newest.
    Should I try to downgrade to an older firmware?
    I shared the whole drive in the settings.

  • '[FAQ] Twonky DLNA Media Server Setup & Use

    Some Frequently Asked Questions Regarding Twonky, And Some Answers The MyCloud includes a Twonky DLNA Media Server.  Sadly it doesn't seem very well integrated into the MyCloud, and the two fight for supremacy.  I've spent a long time trying to understand how it works, and reading the forum, I see many other people also have trouble with it. So I thought that, rather than trying to answer these questions individually, I'd try to write an FAQ covering the things I've found, and the problems I or others have encountered, and the solutions.
    I'm not a member of WD staff.  I'm not a MyCloud, Twonky or Linux expert (but I'm moderately competent).  But I am stubborn, and determined to find out how to make the thing work the way I want it to.  If more expert users find fault in this FAQ, or have other insights to offer, then feel free to post comments.  I'll edit this first post and make corrections and add any FAQ&A that are added.
    Where I am unsure of something, I'll enclose it in [brackets].  Feel free to investigate and confirm or disprove my observations... Where I mention control settings, I use a | to indicate a level of hierarchy in the menu system.  This is to distinguish control settings and file system paths.
    Ideally, we'd shame WD into doing a better job of integrating Twonky into the MyCloud, so it's not such a struggle, and doesn't require Linux administrator-level skills to make it work properly. Starting the Media Server and setting up a Media LibraryQ. What is a Media Server?
    Q. How do I start the Twonky Server?
    Q. How do I control the Twonky server properly?
    Q. Where should I put my media so Twonky finds it?
    Q. Why doesn't Twonky find my media?
    Q. Can I stop Twonky searching in certain folders in my media storage folders?
    Q. What are the 'Shared Media' folders for?
    Q. Why can people using DLNA clients see media in my private share?
    Q. How do I control when Twonky rescans the media store? Optimising operation of the Media Server
    Q: How does the Twonky service work on the MyCloud?
    Q. Where is the Twonky database stored?
    Q. Where are the Twonky settings stored?
    Q. What do all the settings in Twonky's configuration file do?
    Q. How do I clear Twonky's database and start again?
    Q. Where can I find debug log files for Twonky?
    Q. How do I stop MyCloud breaking the Twonky Server?
    Q. Can I change to location of the 'Shared Media' folders?
    Q. Why does setting a Twonky access control password prevent the MyCloud from sleeping?
    Q. Can I replace Twonky with another Media Server?
    Optimising behaviour for Media Clients
    Q. Why does my media player not show the right track information?
    Q. How can I get Twonky to provide full size artwork to clients, rather than crude thumbnails?
    Q. How can I change the media 'views' I see in my DLNA client?
    Q. Can I add my own category to the Music/Photos/Videos categories?
    Some Prerequisites
    You'll need to know how to use the WD Dashboard browser interface to control the MyCloud:
    http://wdc.custhelp.com/app/answers/detail/a_id/10420
    You'll need to know how to use the Twonky UI browser interface to control Twonky:
    http://wdc.custhelp.com/app/answers/detail/a_id/3299
    You'll need to know how to use SSH to log in as root to the MyCloud:
    http://wdc.custhelp.com/app/answers/detail/a_id/10435
    Note the big warning signs about warranty.  IMHO, it's a bit off to make dire threats like this when you often NEED to SSH login to get the advertised services to work properly.
    Some Unix experience will help, but I'll try to explain all the commands you'll need.  Experience with a Unix text editor such as vi or nano is assumed.

    Q. How does the Twonky service work on the MyCloud?
    A: [Twonky is installed as a Linux service.  Like other such services, there is a service control file in the /etc/init.d directory]:
    /etc/init.d/twonky
    This is called when the twonky service is invoked, and there are a number of options for the control of Twonky using an SSH root login:
    service twonky start
    service twonky stop
    service twonky restart
    service twonky status If you execute the start or stop commands with Media Streaming turned on in the Dashboard, you are likely to confuse the Dashboard; you may get an 'Error 400162'.
    'start' calls writeTwonkyContentDir.sh, which, as we'll see later (Q: How do I stop MyCloud breaking the Twonky Server?), reads the /etc/contentdir file and modifies the twonkyserver.ini file to set the media search paths and types, and then starts the Twonky server.
    [It is assumed that the MyCloud Dashboard uses these Twonky service calls to start and stop the Twonky server].  Q. Where is the Twonky database stored?
    A: Since Twonky is a service running on MyCloud, it is not visible in the shared space, so you have to log in via SSH, and navigate around the MyCloud's Linux file system.
    Once you have logged in, use the cd command to change directory to Twonky's area:
    cd /CacheVolume/twonkymedia Now see what's there with a directory list:
    ls -l  Q. Where are the Twonky settings stored?
    A: One of the files listed above is the Twonky configuration file:
    twonkyserver.ini This file contains all the settings that control how Twonky works.
    Now, this is where some of the fighting occurs, because both MyCloud and Twonky can modify this file...
    When you are happy that Twonky is working correctly, I'd recommend making a copy of the file in your Public area, where it won't be mangled by MyCloud firmware upgrades or restarts.  For instance:
    cp /CacheVolume/twonkymedia/twonkyserver.ini /shares/Public/twonkyserver.ini
    If things go wrong, you can reinstate this file by swapping the source and destination.  Q. What do all the settings in Twonky's configuration file do?A: [Most of them are provided with comments that explain their purpose].
    [There are some 'magic numbers' embedded in the configuration file that seem to cause problems, and I don't know what changes those; I suspect that a firmware upgrade does it.  If anyone can monitor these values before and after a MyCloud firmware upgrade and report any changes, I'd be obliged:
    # UserID Please Do NOT change it manually
    userid=<redacted>
    # twonky info for Media Feeds Please Do NOT change it manually
    twonkyinfo=<redacted>]  Q. How do I clear Twonky's database and start again?
    A: If Twonky doesn't seem to be behaving correctly (not finding media correctly, or partially, or finding unwanted media), then it may be useful to clean up the database. There are a number of escalating actions you can take.  Starting with the mildest, and increasing in severity, these are as follows:
    1. Initiate a library rescan, using either Settings|Media|DLNA Database|Rescan in the Dashboard, or Settings|Advanced|Server Maintenance|Rescan Content Folders in the Twonky UI.
    2, Initiate a library rebuild, using either Settings|Media|DLNA Database|Rebuild in the Dashboard, or Settings|Advanced|Server Maintenance|Restart Server in the Twonky UI.
    3. Finally, you can completely clear out Twonky's working area. [This can be useful if you notice the '[Error] - LOG_SYSTEM: Error: 2 No such file or directory' report in the Twonky logfile.  I don't know what causes this error, or whether it has serious consquences, but I have found it to be associated with periods of diffcult behaviour.] Turn Twonky off using the Settings|Media|DLNA Media Server|Media Streaming control in the Dashboard.  Then SSH root login, and hide the entire Twonky working area:cd /CacheVolumemv twonkymedia twonkymedia_bak Restart the Twonky Server using the Dashboard; it will re-create Twonky's working area with a clean version with default settings.  You can then use the Twonky UI to put your settings back in place.  You might try doing this one-by-one, saving the settings and restarting the Twonky server from the Twonky UI each time, then checking the logfile after the Twonky UI has re-appeared. Once you're happy with the operation of the clean startup, you can delete the old Twonky working area:
    rm -f -R /CacheVolume/twonkymedia_bak
    The -f -R flags mean 'delete EVERYTHING from here down... yes, I mean it'.  nb. it will only delete the Twonky database; it won't delete any of your media.  But do be careful that you type the command in correctly; rm -f -R is a powerful command (-f means force, -R means recursive), and could do a lot of damage if you get it wrong...
    Q. Where can I find debug log files for Twonky?
    A: You can enable activity logging using the Settings|Advanced|Logging control in the Twonky UI.  You can also open the logfile from there.
    Alternatively, the logfile is stored in Twonky's area:
    /CacheVolume/twonkymedia/twonkymedia-log.txt
    There's also a MyCloud system logfile that records actions on the Twonky server, such as start and stop:
    /CacheVolume/update.log  Q. How do I stop MyCloud breaking the Twonky Server?
    A: Firstly, go to the Settings|Firmware page in the Dashboard, and disable Auto Update: firmware upgrades completely destroy the /CacheVolume/twonkymedia area, and replace it with new, default version, so you'll be back to square one.
    Secondly, we can stop the problem of Media Streaming restarts overwriting the Twonky UI settings.  Using an SSH root login, enter the following commands:
    cd /usr/local/sbin
    mv writeTwonkyContentDir.sh writeTwonkyContentDir.sh.old
    This disables the script that MyCloud calls when it starts Twonky, which overwrites your settings.
    Another way of fixing the settings is to leave this script alone, but change the file it uses as the source of the settings.  Admittedly, this will still override any changes made via the Twonky UI.  The file is found here:
    /etc/contentdir
    Replace this with a single control line, with no line terminator, e.g.
    +M|/Public/Music,+P|/Public/Pictures,+V|/Public/Videos This will select my earlier settings.
    The format is a comma-separated list of shares and media search and aggregation control flags:
    + enable media searching on the share
    - disable media searching on the share
    A look for all media types
    M look for music
    P look for pictures
    V look for videos
    lower case letters enable aggregation of these media types.
    The | terminates the media type string [you can search for multiple types in a share].  Q: How can I change the location of the 'Shared Media' folders?A: This brings us deep into the guts of the twonkyserver.ini file...  There are a number of settings that control where Twonky stores uploaded files and 'servermanaged' media, [which are used for aggregation], and there is no control setting for them in the Twonky UI.  To change the location of the folders we have to do an SSH root login and edit the twonkyserver.ini file.  The lines in question are as follows:
    uploadmusicdir=/shares/Public/Shared Music
    uploadpicturedir=/shares/Public/Shared Pictures
    uploadvideodir=/shares/Public/Shared Videos
    servermanagedmusicdir=/shares/Public/Shared Music
    servermanagedpicturedir=/shares/Public/Shared Pictures
    servermanagedvideodir=/shares/Public/Shared Videos
    You can change these locations to suit your desired file system.  For instance, you could create a single 'Shared' folder in the Public area, with sub folders for the different media types, e.g.
    uploadmusicdir=/shares/Public/Shared/Music
    Or you could create a Shared sub folder within each of your main media folders, e.g.
    uploadmusicdir=/shares/Public/Music/Shared
    However, if you choose that option, you will need to stop Twonky searching there, by adding 'Shared' to the list of ignored directories discussed above.  Q. Why does setting a Twonky access control password prevent the MyCloud from sleeping?
    A: It has been reported that if a username and password are set using the Settings|Advanced|Secured Server Settings control in the Twonky UI, that the MyCloud then never sleeps.  [It appears that the MyCloud continues to interrogate the drive in some way, hoping to get status of the Media Server from Twonky, but Twonky won't talk to it because it doesn't have the required permission.].
    I don't think this is very important, since the MyCloud is mainly intended for home use, and the Twonky control UI isn't visible external to your local network, and all users on your local network must be trusted*, since you've given them the network access code, [and they have access to the Public area, and could wreak havoc there...] If you need to make your music library available to visitors who cannot be trusted, create a private share and put all your media under that, then enable media serving on that share, and get Twonky to search for media in that private share. DLNA ignores acces control, so DLNA clients will be able to see the media on your private share, but visitors will not have access to your private share via network file access. [However, if you feel that secured access to the Twonky UI is necessary, then I would suggest that you disable the Twonky server using the Settings|Media|Media Streaming conrol, then SSH login as root, and start Twonky using the command:service twonky start You won't get the media scan status in the Dashboard, but the Twonky Server and UI will be running.]
    * Breaches of this trust should be punished in an appropriate manner...
    Q. Can I replace Twonky with another Media Server?A: Yes; forum users hvalentim and Nazar78 have posted good threads about this:MiniDLNA for V3 firmwareMiniDLNA for V4 firmware Kudos to them :-) 

  • I'm trying to load video file into CS6 I keep getting error message: 'Could not complete you request because the DynamicLink Media Server is not available.' No Idea what to do next. Help please.

    I'm using CS6 Extended. My OS is "Windows 7 home premium.
    Can no longer load video files into CS6 for edited I keep getting error message:
    'Could not complete your request because the DynamicLink Media Server is not available.'
    Don't know what this means. Until just now I was able to load videos without any problems. Now I'm getting this message. Any thoughts?

    Hi Mylenium,
    upfront:
    I hope I won't be marked as spam now, since I am posting on a few relevant discussions now to this topic.
    However, I really would like to ask the people who have experienced this problem to see if they were able to solve it.
    Now the real deal:
    I posted a question in this discussionDynamicLink Media Server won't let me import video for video frames to layers anymore.
    The linked discussion is a lot younger, which is why I posted there first.
    I also put in information on the steps that I have tried and my computer specifications.
    I am experiencing this problem for a while now and hope you and jones1351may be able to help out.

  • Could not complete the video frames to layers command because the DynamicLink Media Server is not av

    I have this problem, I have PS CS6 and when I click on File> Import> Video Frames to Layers.. Next, the window that says "Initializing Video Import" starting to load and always get stuck and that's what appears: "Could not complete the video frames to layers command because the DynamicLink Media Server is not available". That's with aaaall the videos.
    PS: I've been trying with File> Open but that's what says "Could not complete your request because it is not the right kind of document"
    Anybody know what happens to my photoshop? Thx!

    The relevant auxiliary service/ helper app is being blocked and thus not launching,. anything from permissions issues to security tools getting in teh way. Check your Task Manager/ Activity Monitor, turn off security stuff, run as admin.
    Mylenium

  • DynamicLink Media Server is not available. I can't open any video file in Photoshop CC and when it does, Photoshop freezers and I can't do anything else. I'm using OS X 10.9.4-3.1 GHz Intel-16 GB DDR3. Any help please?

    DynamicLink Media Server is not available. I can't open any video file in Photoshop CC and when it does, Photoshop freezers and I can't do anything else. I'm using OS X 10.9.4-3.1 GHz Intel-16 GB DDR3. Any help please?

    Indicas que no puedes abrir ningun archivo de video, se supone que has probado varios formatos, mp4, mov,..
    Has actualizado el OSX a 10.9 ?, funcionaba antes? La versión de Photoshop es la CC, no la CC 2014?
    En el menú de Ayuda>Actualizaciones, cual es el resultado, dice que esta al día?
    Tienes abiertas otras aplicaciones?
    Prueba a cerrar todo, espera media minuto y abre Photoshop a ver que ocurre.
    (Estas utilizando un MacBook Pro?)

  • Photoshop 2014 (fresh install) cant open a video because: -. the dynamiclink media server is not avalable – any idea how to fix this on os x 10.5.8 ?

    Photoshop 2014 (fresh install) cant open a video because: …. the dynamiclink media server is not avalable – any idea how to fix this on os x 10.5.8 ?

    i found the error!
    little snitch on os x blocks something (i dont know what exact) of adobe in the background. i have no rule defined for adobe in little snitch, so everything of adobe can go out.
    when i stop little snitch, everything works fine - photoshop opens videos without the medialink error, photoshop starts up in seconds and premiere starts without a quicktime error.
    i report the problem also to objective developement to fix this!
    mad

  • WRT160NL DLNA Media Server Unstable (Twonky Media)

    I have an NTFS formatted USB disk drive (Western Digital My Passport Essential Black 320 GB WDBAAA3200ABK) attached to the WRT160NL wireless router (Firmware Version 1.0.02), and I have video, picture and music files on the USB disk drive in three folders: Videos, Music, Pictures. Auto-scan is disabled, I scan the media files manually by clicking on the 'Scan All' button.
    PROBLEM 1
    The worst problem is that the router is very sensitive to files that can't be recognized by the router as media files. For example if there are subtitle files (*.str) between the media files, then strange and nondeterministic things happen: some valid media files are skipped and not included in the media database; some files included but the file names are mixed. The most irritating in the bug is that there is no log file, where you could find the problem, and so you never know which file cause the problem, and you have to browse through all the files hunting for the cause.
    PROBLEM 2
    When the router is in the process of scanning the media files, then the internet (WAN) connection often can't be used, although the router can be accessed and the status says it is connected to the internet.

    WRT610N maybe have the samme problem, Media Server USB HDD
    Ex, if you edit a playlist *.M3U and do a manuell SCANNING it will recogized the different (because the date is diff ?) If you edit again and make a second scanning (samme date) the playlist dissapear and IS GONE until you reconnect the Hdd or renamme the playlist.
    EX2 : A file named   13 - Ricky Martin - Livin La Vida.mp3 and you renamme it  12 - Ricky Martin - Livin La Vida.mp3 the file  is gone from Media Server !
    Normal use, you add a file , NO problem but it seams getting confused when you edit/renamme/move files.
    I solve it like this EVERY TIME -
    Disabled Media Server
    Rename media folder
    Enabled Media Server
    Scan the renamed folder
    It works   !
    Using WRT610n  Firmware Version: 1.00.03 B15  
    WD 1TB USB HDD with powersuply

  • WRT350N Media Server does not serve music up to a Directv HR20

    I have a Directv HR20.  This device is a UPnP device that is capable of playing Music/Picutres on the TV/Stero system using a media server software.  The intention of my purchase of the WRT350N router was to install a 500GB USB drive onto the router and use the media server software to supply music and photos onto the Dirctv HR20 DVR.  This has not been an easy task.  I can see the pictures and play the pictures without an issue.  I contacted Linksys support via the Live chat and spoke with them explaining how the media server is suppose to supply the music as well and the Directv HR20 is ecpecting a LPCM trascoder to work.  They assured me that they would pass this information up to the development team.  This was almost a month ago and I have not heard back from them yet.  I downloaded the beta version of the firmware and tried it, but it to did not work.  Other media server software does in fact work like Nero 7 media server and Twonky media server software.  I currently use the Nero 7 media server software on my PC to serve music and photos to the Dirctv HR20.
    The Directv HR20 uses a WET54g currently to connect to the home network.  I will need to update this to a "n" type of connection when a game adapter or bridge device is avliable for "n".
    So now here I sit with an expensive USB drive and I cannot use it for the music side of the media server portion of the WRT350N.
    Any help would be appreciated!
    Message Edited by Spanky_Partain on 07-24-2007 07:35 AM

    It is really hard to believe that Linksys is not interested in fixing this issue.  The Directv equipment that is DLNA compliant to Doc 1.0 and the Samsung LN52A860 which is also DLNA compliant will NOT see the media server and take advantage of the USB storage device that has Music and Photos stored on them.
    Come on Linksys by Cisco, get your firmware compliant to the standards the industry is following and STOP tyring to write your own!
    Mark

  • SBS 2011 VM and Server 2012 R2 Hyper-V host. After rebuilding the host image, no email is received, EMC states "You don't have sufficient permissions to view this data" when looking at organization config. Server config not shown on EMC.

    Hyper-V Host Server 2012 R2 x64 drive c:
    All VMs, including SBS 2011 Standard x64 are on drive d:
    I replaced my motherboard and defined a Marvell RAID 1 Mirror for my boot drive C:.  My drive D: containing all of my Hyper V machines remained untouched since the new MB had Intel Matrix Controller with RAID 5, as did the old MB.
    Since the C: drives are a few bytes smaller after configured as a RAID 1, I was unable to restore drive C from the image copy, so I rebuilt a new Hyper-V Host identical as possible using Server 2012 R2 x64.  I had to redefine the Hyper-V machines on
    the host, and the 1st time I brought it all (host and VMs) I had to reconfigure the NICs due to new MAC addresses, and verifying SBS 2011 DNS and DHCP for all physical and Hyper-V machines. Otherwise my Hyper-V SBS 2011 x(64) wasn't touched.
    Now the SBS Exchange 2010 is not receiving mail.  In the Exchange Management Console clicking on the Organization config gives me a highlighted error "You don't have sufficient permissions to view this data".  The Server
    Config is no longer on the EMC.  The Recipient Config looks fine.
    Outlook 2013 x64 connects to the Exchange Server, but no new mail appeared.  There were just a few older messages that came in since the last time I opened Outlook.  My public DNS on GoDaddy was not changed.  I did not change sending mail
    through my ISP Sonic.net.  The SBS internal DNS doesn't have an MX record, but I'm not sure it ever did since my GoDaddy public DNS has an MX record.
    I tried restoring to an earlier Image Copy, but that made no difference.  I'm using the Windows Backup from SBS 2011 for my daily image copy backups.
    - Michael Faklis

    Hi Michael,
    à
    After more research and running the Best Practices report from the EMC, I am missing a slew of ManagementRolesAndRoleGroups from the RBAC container.
    Based on your description, it seems that you have find the cause of this issue. On current situation, I still
    suggest that you should run
    SBS 2011 BPA and then check if can find some relevant errors. Just for a confirmation.
    Meanwhile, please refer to following articles and check if can help you.
    Apply
    missing Exchange 2010 RBAC Management Roles and Policies
    RBAC Manager
    (Exchange 2010 SP2)
    Hope this helps.
    Best regards,
    Justin Gu

  • [46TL868G] DLNA Media Player Playlist not updating

    Hello guys,
    I was wondering - I set up my Network Media Player correctly, and am already able to stream files. However, somehow the list of files does not update itself, e.g. after renaming a file - it still shows the old name despite resetting my Windows 7 PC, or turning off and back on of the TV.
    Do you have an idea why this is like that? What can I do to change this?
    Regards

    Hello,
    thank you for your reply. Unfortunately, I am living in Germany and am not really able to call your given number.
    Let's hope for now, that the community might help me
    Regards

  • IPad smtp outgoing mail server choices not shown.

    I use one mail Gmail account to where all my other accounts forward their mail. This makes it simple for me to organize 10 different accounts.
    In iPad Mail settings I've setup my main Gmail account with 10 other smtp outgoing servers but when I write an email I don't have the option to select which smtp server is used. In Apple Mail (Mac OS) this system works fine as they have the option to select whatever smtp servers are setup.
    What is the point of having the option in the iPad to set multiple outgoing servers if you can not select which ones are used before sending?
    I know I could setup various POP/IMAP accounts for each smtp I prefer to use but why make it so complicated and waste space and bandwith downloading duplicate messages?
    Has anyone found a solution to this or am I missing something obvious?

    Yeah, I don't know why the difference. Interestingly for me, the iOS version in iOS4.2 is "better" than the OSX version of Mail because now I can have more than one Exchange account.
    I am sympathetic with your need to separate your lives. I have a client that accidentally got one of my alternate email addresses and cannot/will not update his address book with the "correct" address, despite my requesting several times over the course of a year. In any case, I don't think there is any way around this other than completely changing your email address. (If not a second Gmail, then Yahoo, Hotmail or other email provider.)
    The only time I've ever seen a "no password" SMTP server was as I previously said, it used a "network authentication" method. Many, many moons ago, SMTP servers often didn't have password authentication so would often be used for spam relaying. Before mobile users, "network authentication" by ISPs was fine since they could figure out which user was spamming since they could trace the IP addr, MAC addr, etc back through the physical link to the user. But with mobile users who change networks constantly, the general trend was to password authentication, even for wired ISPs since their users would want to have access to send mail while away from home. (e.g.: you're a RoadRunner customer, but want to send mail while using your laptop on vacation in Italy.) This "prior authenticated download" I've never heard of anyone else doing.

  • Logitech Media Server will not starts since OS update

    Hi All
    Updated to OS 10.10 during the week and since then my Logitech server won't start. I click start, in system preferences and in just 2 or 3 seconds it stops again. Downloaded latest Logitech server but still no use.
    Any idea?
    Cheers
    Jonna

    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
    The title of the Console window should be All Messages. If it isn't, select
              SYSTEM LOG QUERIES ▹ All Messages
    from the log list on the left. If you don't see that list, select
              View ▹ Show Log List
    from the menu bar at the top of the screen. Click the Clear Display icon in the toolbar. Then take one of the actions that you're having trouble with. Select any messages that appear in the Console window. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
    The log contains a vast amount of information, almost all of which is irrelevant to solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
    Please don't indiscriminately dump thousands of lines from the log into this discussion.
    Please don't post screenshots of log messages—post the text.
    Some private information, such as your name, may appear in the log. Anonymize before posting.

  • Photoshop CC: DynamicLink Media Server is not aviable

    It may have to do with the update to 14.1.1 but suddenly when I try to open a video file the above warning appears. Anyone else with this problem or maybe someone with a solution?
    (In PS CS5 everything just works fine)
    Windows 7 64bit
    B.T.W., is there a way to repair a CC application installation?
    Message was edited by: harrieb

    (Strange to reply to my own message but there is no "Edit" button)
    For what it is worth: I restored my Windows to a previous state and everything worked fine again.
    Off course CC wanted to update my PS and Bridge and I let it do so. Now everything still works fine but the PS "About" screen states that I have version 14.1.
    Guess the only thing I can do is wait for 14.1.2 or so...

Maybe you are looking for