EA6500 doesn't show device connected to 5 port workgroup switch

I just replaced a defective Linksys e4200 with an ea6500.  After some help over the phone, I got it up and working, but one computer on my local network doesn't show up.
I had connected an 8 port 10/100 Linksys switch to my 4200, and my wife's computer was connected to that.   Her computer shows the ip address as 192.168.1.133 and it is connected to the internet with my new router.  But the ea6500 doesn't show a device with the ip address.  Instead it shows  what it calls a Network device with ip address 192.168.1.130.
How can I see the devices connected to the 5 port switch and determine what ip addresses they have been assigned?
Solved!
Go to Solution.

I am using a switch with my network with an EA router and it shows the devices correctly. Turn off the computer that is not showing up in the device list and check if any device will show as offline adter that. Remove it from the device list and reboot the router afterwards. Once the router is ready, open the router page again and power on the computer and check if it will be detected correctly. Hope this helps.
Edit: Check and make sure that you have the latest firmware loaded. If not upgrade the firmware and do a reset after the firmware upgrade. Check your device list after that.

Similar Messages

  • While playing games like NFS and CounterStrike my macbook pro it does connects to the hotspot by any device either a Windows laptop, but doesn't show or connect to the server (LAN) created by windows player.Or neither connects to the server that i created

    While playing games like NFS and CounterStrike my macbook pro it does connects to the hotspot by any device either a Windows laptop, but doesn't show or connect to the server (LAN) created by windows player. Or, any other devices doesn't  connects to the LAN server that i created in the Game.     
    Could any one help me please.

    Please do not post more than about 50 lines of console logs or output from an Application crash at a time. No one can make it through those.
    If you had a kernel panic, those are Full of good information and should be posted in their entirety. They are stored, and can be read back and posted using this article:
    How to log a kernel panic

  • "Device connected to USB port has malfunctioned and is not recognized"

    When I hooked my nano up to my computer today, the screen went black with a silver apple icon on it...it's still all lite up and on...but it won't change from that screen.
    And my computer says, "Device connected to USB port has malfunctioned and is not recognized", so it won't show up in iTunes.
    What do I do?? Thanks.
    Windows    

    iPod appears in Windows Explorer but does not appear in iTunes.
    iPod does not appear in iTunes.
    Fast user switching in Windows XP is not supported.
    Strange iPod behavior.

  • How can we find the hostname of the devices connected with the interfaces of switch?

    how can we find the hostname of the devices connected with the interfaces of switch ? I have tried mac address and ARP, there are lot of servers connected with the switch having multiples LAN cards. So mac table shows the mac of physical machine as well as virtual machines. But i want to know only the physical machines. Is there any other method to find out the IP address, hostname of the physical machines only? 

    Hello Leo Laohoo
    Thanks for this information
    In our network most of the Servers are not of Cisco. Some of them are Vmware machines, some are Hyper V machines, etc. 
    Does IP device tracking show us only the IP addresses of the Physical Machines of the Vmware Server not of Virtual Machines?
    Regards
    Mukesh Kumar
    Network Engineer 
    Spooster IT Services

  • I can't see my devices in itunes, first I couldn't get my computer to notice my device, now it does but itunes doesn't show devices

    I can't see my devices in itunes, first I couldn't get my computer to notice my device, now it does but itunes doesn't show devices

    Same thing is happening to me, before it wouldnt regognize it at all, it would sync but it would say on my iPhone "this device cannot be charged" and now it wont come up at all.
    But it does work on my laptop, can sync on iTunes and chrages it fine, the problem is my computer

  • HT202731 Unstable operation when 2 or more USB devices connected to usb port on a MacBook Pro running Yosemite

    I have tried connecting a number of devices to my MacBook Pro but I have found if I try to connect 2 or more using either usb ports or a usb hub the computer reports 'disk not ejected properly' and sometimes it will fail to recognise the device and remove it from the desktop or it stalls operation and I have to turn the computer off at the power button.
    I have tried erasing the hard drive and reinstalling the operating system.
    I have done various types of reset suggested by apple support.
    The computer has been to an Apple dealer who has tested the hardware but found nothing due to the intermittent nature of the problem.
    I have operated the computer with only the software originally installed on it present.
    Could it be possible that a virus could be present on the usb devices I am trying to connect?
    My computer is a MacBook Pro (13-inch, Mid 2012)
    Processor 2.5 GHz Intel Core i5
    Memory 4 GB 1600 MHz DDR3
    Startup Disk Macintosh HD
    Graphics Intel HD Graphics 4000 1024 MB
    Operating System X Yosemite 10.10.1
    Devices I have connected to USB ports all USB 3.0 compatible in a variety of combinations:-
    7 port superspeed USB 3.0 hub (powered).
    4 port Inateck USB 3.0 portable hub (not powered).
    Buffalo ultra portable 500Gb USB 3.0 hard drive.
    Seagate Expansion portable 500Gb USB 3.0 hard drive.
    Seagate Expansion desktop 2Tb USB 3.0 hard drive (powered).
    Seagate Expansion desktop 3Tb USB 3.0 hard drive (powered).
    ScanDisk Cruiser Edge 16Gb USB stick.
    ScanDisk Cruiser Edge 32Gb USB stick.
    Hewlett Packard 16Gb USB stick. (This causes an instant crash now.)

    Why?
    - Because when I'm editing/ rendering lots of HD video everyday, I don't want to share system resources between virtual machines... I want the entire system's resources devoted to what I'm doing.
    - I don't want to spend anymore money than I have to in order to buy one of the faster virtual systems. Not to mention, I've had a bad experience with Parralels in the past and I'd rather not use one again.
    - I really don't want to clutter up my system anymore than I have to for a project that's only going to take a few weeks.
    - I don't mind swapping hard drives... it takes two minutes, and I have an empty ssd just sitting on the shelf.
    So, back to my original question. Can I just swap the computer's drives, then install Ubuntu on the second drive and be good to go without any harm to my MacBook Pro or OSX on the other drive (which wouldn't be connected when Ubuntu is running)?
    Thanks.

  • How to aquire data of Bluetooth device connected to USB port by using LABVIEW?

    I am using LabVIEW2010 and want to acquire data of Bluetooth device which is connected to USB port while i am using OS xp3
    THANKS

    Does it have a driver to use it as a serial port?
    Say hello to my little friend.
    RFC 2323 FHE-Compliant

  • Blutooth doesn't show device names

    When trying to setup a connection between my new iPhone 3G and my car's blutooth car kit, the iPhone only shows the device category names not the actual device name. Same thing happened with my PC. Has anyone else come across this?

    I have a similar problem in my 08 Dodge Charger connecting to UConnect. My phone worked fine prior to the upgade to 2.0. So far I feel like this was actually a downgrade. I am able to pair the devices but when I try to make or receive a call it says no phone connected. Apple really needs to get it together!!!

  • New iTunes doesn't show devices when plugged in

    When I plug in any of my devices iTunes no longer shows them.  How do I get them to show?  Even if iTunes is not running when I plug in a device it dowsn't automatically run iTunes.  What gives?

    Click on View, Show Sidebar.

  • I have updated to the latest version of iTunes (11.2.2.3). However, when I connect my iPod it shows in My Computer and iTunes opens automatically when the iPod is connected but the device doesn't show in iTunes.  Any ideas?

    I have updated to the latest version of iTunes (11.2.2.3). However, when I connect my iPod it shows in My Computer and iTunes opens automatically when the iPod is connected but the device doesn't show in iTunes.  Any ideas?  I am on Windows 8.1 and my iPod is a Classic

    Hi murr18140,
    Welcome to the Support Communities!  The article below will help you troubleshoot the issue you are having with your iPod classic not being recognized in iTunes for Windows:
    iPod: Appears in Windows but not in iTunes
    http://support.apple.com/kb/TS1363?viewlocale=en_US
    I hope this information helps ....
    - Judy

  • I want to restore my phone by connecting my Iphone4 to iTunes in Mac but it doesn't show phone device. What should i do now??????

    I have problem when I updated iOS7 yesterday. At first, there was a message popped out in my Iphone 4 said "iOS7 available for u to update, then i clicked "update", then it said "wait while it verifying", after that my phone tuned blank and what i saw was only the "logo of apple". Until now i see only that Apple logo, i can't either switch my phone on or off.
    My iTunes in Mac is just updated to version 11.1
    I want to restore my phone by connecting my Iphone4 to iTunes in Mac but it doesn't show phone device.
    I don't know why it doesnt connect to pc(Mac pro).
    Any solution?

    You need to restart the phone in DFU mode and update the software.
    To restart the phone in DFU mode press the power and home button simultaneously for like 10 seconds once the phone is switched off release the power button keep holding the home button while you connect to the computer which has Itunes running and then you can restore or update the software, you can download the update and connect after the software has been downloaded if your phone disconnects, And enjoy you new IOS7.

  • HT1386 i got a used ipod touch and when I connect it - it doesn't show up on my computer. I have an Itunes account and it does not show my device at all. any clue what I', doing wrong? The ipod is on and plugged in

    I am having trouble - when I turn on my ipod touch - the only thing on the screen is a usb cable with an arrow pointing to the itunes logo. I got it from a friend who cleared all of his stuff off of it. I can't get any of the stuff I downloaded on it. maybe it didn't sync with my computer. it doesn't show up when I go to the itunes store on the top bar next to the library tab either. HELP ! lol

    iOS: Device not recognized in iTunes for Windows
    or
    iOS: Device not recognized in iTunes for Mac OS X

  • Connected a flash drive but it doesn't show up in devices

    I downloaded songs to my flash drive and i want to put them into i tunes but it doesn't show up in devices do I need to look somewhere else. Thanks

    Your flash drive won't show up in iTunes, look for it in Windows Explorer, it will probably be labelled Removable Drive.

  • Why won't my ipod sync into itunes? it doesn't show a device is connected when i connect my ipod.

    my ipod wont show up on itunes, it says there is no device connected even when my ipod is connected to my computer.

    Hello gespinal94,
    Thanks for using Apple Support Communities.
    For more information, take a look at:
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    1. Update iTunes
    2. Check the USB cable
    3. Verify that Apple Mobile Device Support is installed
    4. Restart the Apple Mobile Device Service
    5. Verify that the Apple Mobile Device USB Driver is installed
    6. Check for third-party software conflicts
    Have a nice day,
    Mario

  • My ipod touch is connected to my USB port, it sais it's charging although... it doesn't show on itunes that i have plugged my device in, once i turn my ipod on the apple icon appears but then loses battery streight away and starts off all over again.

    although it is doing what i asked it to do, i want it to charge, ok so it does it... although when i turn it on it's as if it's either not charged at all but only enough to have the apple icon on my ipod, once it's had enough (which is like, a minute) it switches itself off and carries on charging, sometimes it switches itself on but this just takes it back to step one. also, when i connect my device to the USB port itunes does not recognise it for some reason, i've updated the newest version of itunes recently and i've tried annother ipod on annother computer with the same USB cable, so it's either the newest version of itunes, my ipod or my computer. please help
    P.S,
           i do have the required version of windows for this to work, my computer isn't a mac, it's a pc, hope this helps...

    how long have you had your ipod? mine did the same but after a while you need to get a new one because of the battery...

Maybe you are looking for