EA6500 WAN IP Release Problem

To all I need to switch back to my old router currently I am using the EA6500 in the GUI of the latest firmware there is no longer a button "Release IP Address" but it has been replaced with "Release and Renew" button this is causing that the IP address lease form ISP never gets released and I can not switch the routers. Please help I need to fix this issue ASAP

As I read from your other post, your ISP is Verizon. How did you set up your old router before with your modem? Was it on DHCP or PPPoE? All you have to do is reconnect your old router back from modem's ethernet port to router's internet port via ethernet cable. If you can get online with the modem again getting an ip address of 192.168.1.xx then to set the old router you change it's ip address to 192.168.2.1. If you were on full bridged mode before with modem then use PPPoE on the router with the correct account username and password for your modem so that it can be authenticated on the router. I have a link below to help you set up your old router again. As for the new router's button under status, I believe it does both and Cisco just made it into one button unlike from before that it is separate.
Setting up a Linksys router for DSL Internet connection

Similar Messages

WRT54G v7 WAN DHCP client problem

I've recently started having a strange problem with my WRT54G. Internet access is via a Cable modem and has been working fine for months, and the cable modem works fine so I suspect the problem is with the router. However the router is also working, mostly, so I figured I'd see if anyone here has any suggestions. Here are the details of the problem:
The router WAN configuration was set to DHCP.
It used to happily pick up a new IP address from the cable modem whenever necessary.
One night the router stopped picking up an IP on the WAN side. (nothing was changed. I'm the only one in the house who goes anywhere near the router)
Connecting the modem directly to a PC works fine (suggesting the modem's DHCP server is fine).
Copying the WAN IP config from the PC to the router, as a Static IP, also allows it to work when the modem is plugged back into the router and the router to a PC (which is how it's setup now, but it's a pain to have to mess with the physical connections and manually reconfigure the router every time the modem drops a connection (which is another issue, but not one for this forum...)).
So both the modem and the router seem to work except for the router's DHCP client. It works fine as a DHCP server for the LAN.
The firmware was already upgraded (and working), I've followed the standard power-cycle procedure, I've released and renewed the IP via the Status tab in the web interface, and I've tried resetting the router using both the button on the unit and via the web interface to revert to factory defaults.
Any suggestions?
Solved!
Go to Solution.

I also had this problem which occurred after >2 years of the router working fine. After changing MTU to 1300, cloning the PC MAC address, and power cycling the router and modem fixed the problem. But I was curious to see which change did the trick, so I changed both back to the default (MTU = auto and not cloning the MAC address) and it worked fine! I think the router problem is intermittant and may appear to be fixed by changing setting, but I fully expect it to reoccur.

LRT224 WAN IP Release and Renew

I am trying to debug an issue where my internet performance drops to nothing after about 18 hours of operation. I have bypassed the LRT224 for several hours and my cable modem seems fine. So now I am focused on the LRT224.
When I log into the router and try to release and renew the WAN IP. It will release just fine but will never renew and get a new IP.
A couple of weeks ago I upgraded the firmware to the latest on the website. However, I just did an upgrade in place and did not go through a factory default reset.
The internet performance issue seems to happen when I run the heck out of the connection using encrypted traffic.
Questions
1) is there a problem with the release/renew function in the latest firmware?
2) should I do a factor reset and reconfig the router to see if that clears up both problems?
3) Has anyone else seen performance issues after 16 to 20 hours of operation?

Yes you should do the reset to factory defaults and reconfigure with the latest firmware upgrade.
After you have done the reset see if you notice the issue I notified Linksys engineering about in my last post in the below thread:
http://community.linksys.com/t5/Linksys-Small-Business/LRT214-DNS-Proxy-stops-working/td-p/928464/pa...
If you do see that issue after about two week please add a post to that thread regarding it.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Purchase Requisition Release Problem

Hi All,
I have a release procedure set up, and the strategy pulls up correctly when a PR is made. When I view collective release from ME55, the PR's show up, and I am able to release line items from that screen. However, when viewing the PR from ME53N, in the Release Procedure tab there is no green check next to the release code with which to release the line. Also, if I do release the PR from ME55, I cannot go to ME53N and cancel the release from the Release Procedure tab.
I am a user with all security access, so it is not an authorization role problem. The release group is also configured to release by line item, so that is not the problem. I have set up other release procedures which allow the release/cancel release function from ME53N before... what could be the problem this time?
Thanks,
J

hi.
There are two ways of releasing purchase requisitions:
Individual release (Tcode - ME54)
You release items of an individual purchase requisition or - if the requisition has to be released in total - by releasing one item you simultaneously release all the others.
Collective release (Tcode- ME55)
You release all requisition items or complete requisitions that are awaiting processing by your release code. This is the preferred method if you frequently have to effect release.
Display PR -with release status (Tcode-ME53N)
One can only see release status in ME53N & can not change release.
hope it helps to you.
Regards,
Rahul

Purchase Requisition Overall Release problem with several CostCenter

Hello Gurus!!
I need your comments!!!
I define the Purchase requisition as Overall Release, and woks !! but I have a Issue.
I have an entry in the CL24N txn as follow:
AccAssgCat = K
Plant              = CC01
CostCenters = 10001
                        10002
                        10003
totalAmt        = 1USD to 1000US
So when I create my purchase requisition with only 1 Cost Center the release strategy is called and PR can be released.
But When I create the purchase requisition with CC 10001 and 10003, the requisition is not subjet to release!!! (note TotalAmt = 15usd)
I assume that as both are into the release strategy the system will take both CC and ask for release!!
What I can do to fix this situation??

Dear Marco Antonio,
I have never faced your issue, but have an idea of what you can do.
Activate Enhancement M06B0005   EXIT_SAPLEBND_004
Then in the program zxm06u31 put the following code line:
e_ceban = i_ceban.
and also a breakpoint so that it stops automatically upon PR verification or saving.
Activate and then create a PR with the problem you are facing. On saving the program will stop in your breakpoint.
Look at structure i_ceban there you will find the values that your release strategy is getting from the document and with which it will try to determine the strategy based on your classification.
I the standar logic is not what you want maybe you can put some logic of your own based on account assignments in structure C_EBKN.
Well, tell me what happens
Best Regards,
Sebastián Ligueros

Thinkpad A31 Ultrabay Plus release problem

I have a Thinkpad A31 that I'm repairing - I removed the Ultrabay enclosure that the CD-ROM fits into.
I've reinserted it and have issues with the eject lever.
The release mechanism allows the eject lever to come out, but there is no resistance on the eject lever (when pushing it in) with a CD-ROM in the _Ultrabay Plus_. This means that the only way to eject the CD-ROM is to manually pull it out, which requires the keyboard and plastic palm area to be removed.
I have checked the springs and they are present on the eject lever mechanism.
I have a copy of the A31 manual and have read up on the Ultrabay sections.
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-39796
http://download.lenovo.com/ibmdl/pub/pc/pccbbs/mobiles_pdf/92p1902.pdf
I will work on getting images of the parts/pieces for further information.
Thanks,
Mike
Solved!
Go to Solution.

I've only had to do it once, and that was a while ago, but I believe there's a post by Ray Kawakami on TPF dealing with this problem, I'm just way too tired to look for it now......
With no intention to insult you whatsoever, two bays exibiting the same problem sound like a human error to me...of course, being a human myself, I may very well be wrong...
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

[iPhone] AppStore release problem

Hi Guys,
I've got a little problem when I come to release an app.
I've watched the video regarding AppStore releases on iTunes and read all the other stuff, I think my xcode is all setup fine.
When I come to build the app using my release profile, it all builds fine. However when it comes to install the app on the phone, i get the error:
Your mobile device has encountered an unexpected error (0xE800003A) during the install phase: Verifying application
How can I fix this? To me it looks like the phone doesnt have the correct key install so it cant validate the app? I'm going to do a vanilla install of iPhone OS, any thoughts?

Hey, I'm having a somewhat similar problem in that my development builds all work fine, my app is debugged and ready for distribution build so i can upload to itunes connect but for some reason the distribution prov. profile is not showing up as an option under 'Code Signing Provisioning Profile' in project info (i have 'Code Signing Identity' set to 'iPhone Distribution: MYNAME').
I created a distribution certificate and distribution profile. I have both certificates in keychain access (development and distribution) as well as the WWDC certificate. i have a private/public key pair for each cert. i have the distribution provision file in the 'provision profiles' directory and it shows up under provisioning area under each device i have in 'organizer' (even tho i can't select it since it's distribution).
I have spent like three hours no trying to figure this out. (i even deleted/revoked both development and distribution certificates and prov. profiles and started over to no avail) Anyone have any idea???

Billing releasing problem in vf02

Hi
At the time of releasing the billling document below error will appeared
Delivered/invoiced quantities cannot be updated in CO
This is the error messege
Delivered/invoiced quantities cannot be updated in CO
Message no. KI137
Diagnosis
For account assignment object WBS CP.0065.2, the delivered or billed quantity is to be updated in the unit of measure EA for material number 1025697.
The system has found a totals record (COSL) that already exists for the account assignment object WBS CP.0065.2 with unit of measure KG. However, you cannot convert the quantity from EA to KG.
System Response
The quantity cannot be updated in the totals record, which means that the quantity is missing for the receiver after the settlement of WBS CP.0065.2 (for example in CO-PA). Only the posted quantity is saved in the CO line item (COEPL table).
Procedure
Change the material KG and define KG in the master data record as an additional unit of measure.
If you can have the quantity in EA in the COSL totals record without it causing any problems, you can deactivate this error message in customizing, or change it to a warning or information message.
To do this, see the implementation guide (IMG) for "General Controlling" under the following activity: Change Message Control (work area KI, message no. 137).
If you have any questions, contact your CO consultant.

Solution is any of these.
1. Change Units of measure of WBS element from EA to KG - PS
2.Change the material unit of measure from KG to EA -MM
3. Define conversion rules between UOM EA and KG - MM

WS2000077 (Purchase Requisition Release) problem

Dear all
workflow task WS2000077 (Purchase Requisition Release) causes the following problem:
While executing an approval release (ME54N) through workflow, the result is always 'requisition release refused'.
Does anyone know why?
I appreciate your help in advance

Hi,
Go through the below links it may help you...
Workflow Definition WS20000077 and sequence of the events, significantly...
po release workflow issue/problem
PR Workflow problem
std workflow ; user to role agent assignment ?
Regards,
Udaya.

PO Cancel release problem

Hi, experts:
I am a beginer of SAP workflow, I've got a problem when testing customized PO cancel release workflow.
My workflow is quite simple, just test whether the event 'SIGNIFICANTLYCHANGED' was trigered when cancel PO. I will receive information in my SAP Business workplace.
Here is the configuration of PO release Strategies:
RGroup Rcode Workflow Agent
PO     C1     1     Blank
PO     C2     1     Blank
PO     C3     1     Blank
PO     C4     1     Blank
In my customized workflow template, I use the event 'SIGNIFICANTLYCHANGED' to deal with PO cancel release.
But I find that this event will not be triggered from Level C4 cancel to C3.
Here is my test result:
Cancel        Result
C4->C3       Not triggered
C3->C2       Trigered
C2->C1       Trigered
I can get the result from my Business workplace except cancel PO from C4 to C3.
Does anyone come across with this problem?
Please tell me why and how to handle it, thanks a lot!
Best regards!

Hi,Swaminathan PJ
Appreciate for your reply!
So, shall we change another event or even customize our own event?
My requirement is that send e-mail with PO item detail (*.xls file) to specified users when final release or cancel final release.
Thank you for any good advice.
Best regards!

Purchase Requistion : Overall Release Problem

Hi everybody,
Have a peculiar problem where Item Level release seems to be working fine. And the first time we want to use release at header level and its not working.
The OverReqRel (overall requisition release) is 'checked' [at release group level].
There is just one class, one characteristic within that class (document type).
There is just one group, release code, release indicator and release strategy.
The classification has 'NB' as the document type to be controlled.
The simulation works fine.
The 'Check Release Strategies' shows 'all green' with no errors.
But when we create a PR (txn ME51N) for document type NB, this procedure does not kick in (hence i dont see a new tab at the header level asking for a release).
We have been using item wise release before and are testing the viability of release at header level.
FYI. This is a test system (sandbox) where we have NO configuration for release procedure. This is the first strategy that has been created for testing.
Any help in getting this to work is most welcome.

Hi,
For the document type NB, did you flaged as PR header level release.
Regards,
Ramakrishna

PO releasing problem through ME28

Hi,
When i release the PO from ME28, system showing the following message : - No suitable purchasing documents found..
Note: - I define the new number range for the another plant. also created the new document type for it. PO makes succesfully, but when i m releasing this, showing that message.
What should be the problem here or we should define the release streatgy for New document type / number range.
Plz help...

Check following things
1. You have correctly considered document types in classification
2. All plants have been taken into account in classification
3. Also check the PO value
And also see whether charachterstics, classes has been created and there has been proper assignment of both.
Regards,
SS

Transport request main task releasing problem

Hi friends,
Environment is Linux, ECC5.0, Two system landscape,
I have problem with Transport Request task releasing when I am going to release the subtask that willbe released success fully when I am trying to releasing the main task that task is not released and at that time the system wil hang( mesg on the status bar is tp is connected success fully) thats it we wait for long time then also that looks thats only no log will be generating in usr/sap/trans/log there will be a log on this one that log is
WARNING:/usr/sap/trans/tmp/<username.LOS>is already in use (10), I'm waiting 3 sec(20070326124305). My name:pid 7265 on test(sd1adm)
after saw the this mesg I kill the 7265 pid then also same proablem.
I change the ownet of the request then the request is released but not uppeard in the import que. whn i am trying to import in que as manually that will appear in que but not importing when i press the import button the error is tp error 0203.
I check the both users authorizations also bothe authorizations also same then why it wil happening ???
then I check the nfc also that service also running ok the six services are 1.off 2.off 3.on 4. on 5.on 6.off.
I mount the trans dir also the mounting points also ok tms configuration is also ok
wt can i do plz help me with ur valuable suggessions
Thankyou
Ranjith

Hello Ranjith,
This is usually because the tp transport buffer lock file remains locked by the
operating system (OS).
You should be able to move or delete this file from the DIR_TRANS/tmp dir.
After that the tp should run fine after.
Thanks,
George

MM Service Entry Sheet Release Problem - Plant Not Considered

Dear Experts,
I have a problem in Service Entry Sheet Release as it does not consider plant although it is maintained in Release Strategy.
I have created 1 Class for Service Entry Sheet Release.
This class contains 3 Characteristics, 1st for Plant, 2nd for Value of Services and 3rd for Purchasing Group.
Now the problem is that during the Entry Sheet Release, system does not consider the Plant in deciding the Release Strategy.
It considers the first Release Strategy found for Purchase Group and Value of Service combination, thus ignoring the Plant Characteristic.
Characteristic for Plant is having 'Released' Status
Please suggest what to do so that the Plant is also considered in Release Strategy.

Dear Charlie,
Thanks for your reply.
When I go to CL40N and check then system gives correct Release Strategy as it considers plant there.
But when actually the Entry Sheet is created/saved then system gives wrong release strategy as it does not consider Plant.
Let me tell you that my Release Strategies do contain common Purchase Groups but the Plants are different. So each Release Strategy is unique in this way.
But during Service Entry Sheet Creation system does not consider Plant in determining Release Strategy.
Please Help.

STMS change request release problem

Hi
I am not able to release change requests, sab task able to release, but problem in main request, when I press , release directly, on the bottom it shows u2026tp successfully connected / check writeability of buffers finished with return cod 0. Then screen hangs u2026 manually I have to stop the transition.
I have configured STMS 4,5 times but same problem, in SM59 all retaliated RFCs working fine.
Our System is ERP 6.0, HPUX with DB2
Kindly give me a solution.
But in Tcode STMS >>Monitor>>TMS Alerts>>TMS Alert viewer showers following error:
Date       Time       User           Function      Message                                            System   Clt
23.05.10   17:29:07   TMSADM         TMS_TS_GET_TRLIST    NO_LOG                SID      000
23.05.10   16:58:25   TMSADM         TMS_PS_READ_PROFILE_FROM_DISK                               READ_PROFILE_FAILED                                            SID      000
23.05.10   16:57:30   TMSADM         TMS_PS_READ_PROFILE_FROM_DISK                                 READ_PROFILE_FAILED                                            SID      000
23.05.10   15:55:59   TMSADM         TMS_TP_MAINTAIN_BUFFER                                        RFC_SYSTEM_FAILURE                                             SID      200
23.05.10   15:05:36   TMSADM         TMS_TS_GET_TRLIST                                             NO_LOG                                                         SID     000
23.05.10   15:01:29   TMSADM         TMS_TS_GET_TRLIST                                             NO_LOG                                                         SID     000
23.05.10   14:53:00   TMSADM         TMS_TS_GET_TRLIST                                             NO_LOG                                                         SID    000
23.05.10   14:51:38   TMSADM         TMS_TS_GET_TRLIST                                             NO_LOG                                                         SID      000
Regards
Sunny

Hi Sunny,
Its hard to tell what might be the problem.
I would recommend that you:
- update kernel to the latest patch level for your release
- update your transport tools, tp and R3trans to the latest available for your release
- go into STMS - system pverview and do the 3 checks: Connection test, transport directory, transport tool
check if they all pass.
- try to release a transport and then if it still freezes after all of the above, stop it and check the system log, trans.log, the latest logs in usr/sap/trans/tmp and usr/sap/trans/log to see what was the action it was doing before it froze. That will give a clue as to where the issue may be.
regards,
Paul

EA6500 WAN IP Release Problem

Similar Messages

Maybe you are looking for