EA6900 port forwarding manage
I have EA6900. and I set UPNP enable. also set user can define port forwarding.
When I open single port forwarding, there is only 3 port I opened. that's fine.
BUT.. when I try port scanning on my home IP. I can see 7 ports is open. Not BT open.
I can NOT find any page that let me close those ports. even I turn off UPNP then reboot router.
I am still not allow to manage those open port.
Internet Service Provider and Modem Configurations
What ISP Service do you have? Cable or DSL?
What ISP Modem Mfr. and model # do you have?
If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>http://www.practicallynetworked.com/networking/fixing_double_nat.htm and http://cognitiveanomalies.com/cisco-nat-how-nat-works/ If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ.
doogy wrote:
I have EA6900. and I set UPNP enable. also set user can define port forwarding.
When I open single port forwarding, there is only 3 port I opened. that's fine.
BUT.. when I try port scanning on my home IP. I can see 7 ports is open. Not BT open.
I can NOT find any page that let me close those ports. even I turn off UPNP then reboot router.
I am still not allow to manage those open port.
Similar Messages
-
My eyes are burning from trolling the boards all day. Just picked up an AEBS (12:33 PM CST, 4/20/08), firmware's at 7.3.1, connected the ol' xbox and got a "moderate" on my NAT test. Thats fine, totally expected, no big deal, right? So here's what I do:
1. Assign static ip ads to all machines on the network (xbox is 10.0.1.3)
2. Check to see if NAT is enabled in airport utility: Yep.
3. Enter in the ports as usual:
Public UDP Port(s): 88,3074
Public TCP Port(s): 3074
Private IP Address: 10.0.1.3
Private UDP Port(s): 88,3074
Private TCP Port(s): 3074
The above, BTW, is exact as far as commas and spaces go.
4. Update!
Then, NAT test= Moderate.
OK, it'd be nice if there was a standardized way to forward ports on all routers, I think, no big deal, just need to do a little tinkering.
I put a space after the comma between 88 and 3074, i.e., instead of 88,3074 I did 88, 3074. Moderate. I tried putting a dash in there (88-3074) wouldn't even let me do that, but of course we all already knew that. Tried rearranging all the ports randomly (3074,88). Nope. Well, even though I just gave the machine a static ip address, might as well try a DHCP lease: enter Airport ID. Nothing. Try it again with Ethernet ID. Nothing. I've got an idea, I'll make multiple separate port mapping profiles:
xbox 1: Public UDP Port(s): 88...
xbox 2: Public UDP Port(s): 3074...etc.
NAT test= Moderate.
Hmm, Oh they make port forwarding management software? Lighthouse, eh? I'll try that...oh, it doesn't do anything: Moderate.
I tried a bunch of other things that I knew would be futile, but I've been working on this thing for a couple of hours now and I can't remember them...Oh and by the way, for those not familiar with xbox live: "Moderate"= not good.
I'll telepathically make you feel better if you can help me out.
Love ya,
BooThanks for the prompt reply Duane. Just to clarify: I need another wireless router? I thought airport express was one. I was trying to configure the ports of the airport express's basestation. My connection system is:
-An ADSL 2mbps connection that comes into my home from a phone line and into a D-link GLB 802C modem
-This connects to an Airport Express
-My macbook pro uses the net through the wifi signal provided
-I connect the macbook pro to the xbox through an ethernet cable (mainly because it's far from the adsl router)
I have read that one can forward ports with airport express... -
RV320 Bug - Service Management Table (Port Forwarding)
I'm unable to add more than 16 entries for port forwarding.
It's a RV320 on v1.1.1.06 (newest to date) and it doesn't accept more than 16 entries in the "Service Management Table" required for port forwarding. As soon as I try to enter number 17 and hit save the window closes like it always does but you can see for a short time it says "Critical failure. Please contact support." Everything else works, except for the entry in the Service Management Table. I'm also unable to use it in the port forwarding section, it just doesn't save the entry. I'm unable to add any services to the list unless I delete others but it only works again until number 16.
Actually the "limit" is 37 because it comes with 21 services entered out of the box.
I couldn't find any bug reporting website that I could use without a contract. So I seek for help here.
Anybody else having this issue or is it just my device?10 days ago a post was made in https://supportforums.cisco.com/discussion/12353771/cannot-manage-service-list-all-waited-unacceptably-long-fix indicating there is a new firmware in beta test, I've contacted support to try to get a copy.
I'm moving off Draytek, have a 2830 with latest firmware and various weird issues that they've confirmed are bugs but cannot provide a due date for fix. DHCP randomly giving out wrong DNS server addresses, tagged VLAN support flaky and giving out DHCP details from wrong VLAN (worked around using 1 cable from switch per VLAN and using port based VLAN rather than tagged), App Enforcement for IM blocking causing SMTP and Live.com login issues. And that's just what cropped up last week with the unit at work here. Still using it for our live router as we can't put the RV320 in place until we can configure all the required ACLs which needs more than 16 service entries. -
Port Forwarding for RDP 3389 is not working
Hi,
I am having trouble getting rdp (port 3389) to forward to my server (10.20.30.20). I have made sure it is not an issue with the servers firewall, its just the cisco. I highlighted in red to what i thought I need in my config to get this to work. I have removed the last 2 octets of the public IP info for security .Here is the configuration below:
TAMSATR1#show run
Building configuration...
Current configuration : 11082 bytes
version 15.2
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname TAMSATR1
boot-start-marker
boot system flash:/c880data-universalk9-mz.152-1.T.bin
boot-end-marker
logging count
logging buffered 16384
enable secret
aaa new-model
aaa authentication login default local
aaa authentication login ipsec-vpn local
aaa authentication login ciscocp_vpn_xauth_ml_1 local
aaa authorization console
aaa authorization exec default local
aaa authorization network groupauthor local
aaa session-id common
memory-size iomem 10
clock timezone CST -6 0
clock summer-time CDT recurring
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-1879941380
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1879941380
revocation-check none
rsakeypair TP-self-signed-1879941380
crypto pki certificate chain TP-self-signed-1879941380
certificate self-signed 01
3082024B 308201B4 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31383739 39343133 3830301E 170D3131 30393136 31393035
32305A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 38373939
34313338 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100BD7E 754A0A89 33AFD729 7035E8E1 C29A6806 04A31923 5AE2D53E 9181F76C
ED17D130 FC9B5767 6FD1F58B 87B3A96D FA74E919 8A87376A FF38A712 BD88DB31
88042B9C CCA8F3A6 39DC2448 CD749FC7 08805AF6 D3CDFFCB 1FE8B9A5 5466B2A4
E5DFA69E 636B83E4 3A2C02F9 D806A277 E6379EB8 76186B69 EA94D657 70E25B03
542D0203 010001A3 73307130 0F060355 1D130101 FF040530 030101FF 301E0603
ip dhcp excluded-address 10.20.30.1 10.20.30.99
ip dhcp excluded-address 10.20.30.201 10.20.30.254
ip dhcp excluded-address 10.20.30.250
ip dhcp pool tamDHCPpool
import all
network 10.20.30.0 255.255.255.0
default-router 10.20.30.1
domain-name domain.com
dns-server 10.20.30.20 8.8.8.8
ip domain name domain.com
ip name-server 10.20.30.20
ip cef
no ipv6 cef
license udi pid CISCO881W-GN-A-K9 sn
crypto vpn anyconnect flash:/webvpn/anyconnect-dart-win-2.5.3054-k9.pkg sequence 1
ip tftp source-interface Vlan1
class-map type inspect match-all CCP_SSLVPN
match access-group name CCP_IP
policy-map type inspect ccp-sslvpn-pol
class type inspect CCP_SSLVPN
pass
zone security sslvpn-zone
crypto isakmp policy 10
encr aes 256
authentication pre-share
group 2
crypto isakmp policy 20
encr aes 192
authentication pre-share
group 2
crypto isakmp key password
crypto isakmp client configuration group ipsec-ra
key password
dns 10.20.30.20
domain tamgmt.com
pool sat-ipsec-vpn-pool
netmask 255.255.255.0
crypto ipsec transform-set ipsec-ra esp-aes esp-sha-hmac
crypto ipsec transform-set TSET esp-aes esp-sha-hmac
crypto ipsec profile VTI
set security-association replay window-size 512
set transform-set TSET
crypto dynamic-map dynmap 10
set transform-set ipsec-ra
reverse-route
crypto map clientmap client authentication list ipsec-vpn
crypto map clientmap isakmp authorization list groupauthor
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
interface Loopback0
ip address 10.20.250.1 255.255.255.252
ip nat inside
ip virtual-reassembly in
interface Tunnel0
description To AUS
ip address 192.168.10.1 255.255.255.252
load-interval 30
tunnel source
tunnel mode ipsec ipv4
tunnel destination
tunnel protection ipsec profile VTI
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface FastEthernet4
ip address 1.2.3.4
ip access-group INTERNET_IN in
ip access-group INTERNET_OUT out
ip nat outside
ip virtual-reassembly in
no ip route-cache cef
ip route-cache policy
ip policy route-map IPSEC-RA-ROUTE-MAP
duplex auto
speed auto
crypto map clientmap
interface Virtual-Template1
ip unnumbered Vlan1
zone-member security sslvpn-zone
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
no ip address
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 10.20.30.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
ip local pool sat-ipsec-vpn-pool 10.20.30.209 10.20.30.239
ip default-gateway 71.41.20.129
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip dns server
ip nat inside source list ACL-POLICY-NAT interface FastEthernet4 overload
ip nat inside source static tcp 10.20.30.20 3389 interface FastEthernet4 3389
ip nat inside source static 10.20.30.20 (public ip)
ip route 0.0.0.0 0.0.0.0 public ip
ip route 10.20.40.0 255.255.255.0 192.168.10.2 name AUS_LAN
ip access-list extended ACL-POLICY-NAT
deny ip 10.0.0.0 0.255.255.255 10.20.30.208 0.0.0.15
deny ip 172.16.0.0 0.15.255.255 10.20.30.208 0.0.0.15
deny ip 192.168.0.0 0.0.255.255 10.20.30.208 0.0.0.15
permit ip 10.20.30.0 0.0.0.255 any
permit ip 10.20.31.208 0.0.0.15 any
ip access-list extended CCP_IP
remark CCP_ACL Category=128
permit ip any any
ip access-list extended INTERNET_IN
permit icmp any any echo
permit icmp any any echo-reply
permit icmp any any unreachable
permit icmp any any time-exceeded
permit esp host 24.153. host 66.196
permit udp host 24.153 host 71.41.eq isakmp
permit tcp host 70.123. host 71.41 eq 22
permit tcp host 72.177. host 71.41 eq 22
permit tcp host 70.123. host 71.41. eq 22
permit tcp any host 71..134 eq 443
permit tcp host 70.123. host 71.41 eq 443
permit tcp host 72.177. host 71.41. eq 443
permit udp host 198.82. host 71.41 eq ntp
permit udp any host 71.41. eq isakmp
permit udp any host 71.41eq non500-isakmp
permit tcp host 192.223. host 71.41. eq 4022
permit tcp host 155.199. host 71.41 eq 4022
permit tcp host 155.199. host 71.41. eq 4022
permit udp host 192.223. host 71.41. eq 4022
permit udp host 155.199. host 71.41. eq 4022
permit udp host 155.199. host 71.41. eq 4022
permit tcp any host 10.20.30.20 eq 3389
evaluate INTERNET_REFLECTED
deny ip any any
ip access-list extended INTERNET_OUT
permit ip any any reflect INTERNET_REFLECTED timeout 300
ip access-list extended IPSEC-RA-ROUTE-MAP
deny ip 10.20.30.208 0.0.0.15 10.0.0.0 0.255.255.255
deny ip 10.20.30.224 0.0.0.15 10.0.0.0 0.255.255.255
deny ip 10.20.30.208 0.0.0.15 172.16.0.0 0.15.255.255
deny ip 10.20.30.224 0.0.0.15 172.16.0.0 0.15.255.255
deny ip 10.20.30.208 0.0.0.15 192.168.0.0 0.0.255.255
deny ip 10.20.30.224 0.0.0.15 192.168.0.0 0.0.255.255
permit ip 10.20.30.208 0.0.0.15 any
deny ip any any
access-list 23 permit 70.123.
access-list 23 permit 10.20.30.0 0.0.0.255
access-list 24 permit 72.177.
no cdp run
route-map IPSEC-RA-ROUTE-MAP permit 10
match ip address IPSEC-RA-ROUTE-MAP
set ip next-hop 10.20.250.2
banner motd ^C
UNAUTHORIZED ACCESS TO THIS NETWORK DEVICE IS PROHIBITED.
You must have explicit permission to access or configure this device. All activities performed on this device are logged and violations of this policy may result in disciplinary and/or legal action.
^C
line con 0
logging synchronous
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0
access-class 23 in
privilege level 15
logging synchronous
transport input telnet ssh
line vty 1 4
access-class 23 in
exec-timeout 5 0
privilege level 15
logging synchronous
transport input telnet ssh
scheduler max-task-time 5000
ntp server 198.82.1.201
webvpn gateway gateway_1
ip address 71.41. port 443
http-redirect port 80
ssl encryption rc4-md5
ssl trustpoint TP-self-signed-1879941380
inservice
webvpn context TAM-SSL-VPN
title "title"
logo file titleist_logo.jpg
secondary-color white
title-color #CCCC66
text-color black
login-message "RESTRICTED ACCESS"
policy group policy_1
functions svc-enabled
svc address-pool "sat-ipsec-vpn-pool"
svc default-domain "domain.com"
svc keep-client-installed
svc split dns "domain.com"
svc split include 10.0.0.0 255.0.0.0
svc split include 192.168.0.0 255.255.0.0
svc split include 172.16.0.0 255.240.0.0
svc dns-server primary 10.20.30.20
svc dns-server secondary 66.196.216.10
default-group-policy policy_1
aaa authentication list ciscocp_vpn_xauth_ml_1
gateway gateway_1
ssl authenticate verify all
inservice
endHi,
I didnt see anything marked with red in the above? (Atleast when I was reading)
I have not really had to deal with Routers at all since we all access control and NAT with firewalls.
But to me it seems you have allowed the traffic to the actual IP address of the internal server rather than the public IP NAT IP address which in this case seems to be configured to use your FastEthernet4 interfaces public IP address.
There also seems to be a Static NAT configured for the same internal host so I am wondering why the Static PAT (Port Forward) is used?
- Jouni -
SRP547W, How to use multiple WAN IPs for port forwarding?
Hi folks,
We've run into some difficulty trying to take advantage of multiple WAN IPs in conjunction with the SRP547, and I'm hoping someone here can help out or at least tell us that we're going to need to buy a different router...
What we're trying to acheive is the ability to port forward from our distinct public IPs to different internal servers. Looking at the options under Port Forwarding it looks like we can only configure forwards at the "WAN interface" level, but our problem is that we can't work out how to set up separate interfaces for each of our Public IPs...
Our ISP provides us with a fully managed NTU/router with a single "Internet" ethernet port, which we can use by statically configuring IPs on our end. For this configuration this port has been directly patched to the WAN ethernet port on the SRP547W.
We have been allocated a 255.255.255.248 (/29) subnet, giving us 5 usable IPs after the ISP's gateway address is taken into account, like so:
a.b.c.208 Network Address (/29 subnet)
a.b.c.209 ISP Gateway
a.b.c.210 IP1
a.b.c.211 IP2
a.b.c.212 IP3
a.b.c.213 IP4
a.b.c.214 IP5
a.b.c.215 Broadcast Address
On the SRP we've set up the default "Ethernet WAN2" sub-interface with the following details for IP1
VLAN ID: 4088 (Uneditable)
Connection Type: Static IP
Internet IP Address: a.b.c.210
Subnet Mask: 255.255.255.248
Default Gateway: a.b.c.209
The next step (I would have thought) would be to add a second sub-interface, using similar info for IP2
VLAN ID: 4000 (Chosen arbitrarily)
Connection Type: Static IP
Internet IP Address: a.b.c.211
Subnet Mask: 255.255.255.248
Default Gateway: a.b.c.209
When we try to do so however we get:
Fail!
Conflict with Ether_WAN2 interface address type
I should mention at this point that we're running on firmware version 1.02.01 (023).
Any suggestions on how we can proceed?
Is there a CLI or other method of configuration that might work if the web interface won't?
Thanks,
Tim.OK, I've seen reference to this solution before but not much in the way of details. Perhaps you can spell out how this ought to work, as the Software DMZ doesn't behave as I'd expected it to.
As before, on the SRP we've set up the default "Ethernet WAN2" sub-interface with the details for IP1 with a /29 subnet.
VLAN ID: 4088 (Uneditable)
Connection Type: Static IP
Internet IP Address: a.b.c.210
Subnet Mask: 255.255.255.248
Default Gateway: a.b.c.209
We'd now like to expose a server function on IP2, let's say LAN details for this server are:
VLAN: 3000
VLAN IP Range: 192.168.1.1/24
Server IP: 192.168.1.10
Server Port: 80
So first we turn on Software DMZ:
Status: Enabled
Public IP: a.b.c.211
Private IP: 192.168.1.10
WAN Interface: Ether_WAN2
My understanding, based on what you've said, is that this should expose the whole server to external access via IP2. Unfortunately, it doesn't seem to work this way - we don't seem to have any access at all. Perhaps there's a default deny rule on the firewall?
Just to be sure, I tried creating a rule to allow HTTP traffic to the server in the Advanced Firewall page.
In Interface (WAN): All
Out Interface (LAN): VLAN.3000
Source IP: 0.0.0.0
Source Subnet: 0.0.0.0
Destination IP: 192.168.1.10
Destination Subnet: 255.255.255.255
Protocol: TCP
Source Port: Any
Destination Port: Single:80
Action: Permit
Schedule: Everyday
Times: 24 Hours
Still no dice. What am I missing?
Cheers,
Tim. -
Please Help - Only Some Port Forwards Working
Hi all,
I have the most annoying issue with a Cisco 887VA-K9 port forwarding. Some port work while other don’t and I just can’t see why, however I suspect it is a zone based firewall (ZBF) issue.
Port forwards on the follow ports all work fine:
External port 8021 to 192.168.4.253 on port 80 works
External port 8022 to 192.168.4.253 on port 8022 works
All the rest don’t. I also have SIP phones sitting outside the LAN which are unable to register through the internet with the PBX unit which is in the DMZ network 192.168.4..0
Any help would be great appreciated as this sending me mad. Fully running config below.
Louise ;-)
Building configuration...
Current configuration : 36870 bytes
! Last configuration change at 12:49:03 Magadan Fri Nov 8 2013 by cpadmin
version 15.1
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname QQQ_ADSL_Gateway
boot-start-marker
boot-end-marker
security authentication failure rate 3 log
security passwords min-length 6
logging buffered 64000
enable secret 4 gim.lMOdQK/21R4Wu.QJfOMAv3CIkRyN.hbSTG5xAxE
aaa new-model
aaa authentication login local_authen local
aaa authentication login ciscocp_vpn_xauth_ml_1 local
aaa authorization exec local_author local
aaa authorization network ciscocp_vpn_group_ml_1 local
aaa session-id common
memory-size iomem 10
clock timezone Magadan 11 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-3471381936
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3471381936
revocation-check none
rsakeypair TP-self-signed-3471381936
crypto pki trustpoint test_trustpoint_config_created_for_sdm
subject-name [email protected]
revocation-check crl
crypto pki certificate chain TP-self-signed-3471381936
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33343731 33383139 3336301E 170D3132 30373132 31313332
34375A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 34373133
38313933 3630819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100AB76 5F7EE03F 306F52A0 91E82E04 7A69528D 1839409C 55BCC55A 47F180A9
7B522E9B FBB96A32 715178FE B96B737E 788947A4 CF4791AA 15609E37 A3F66F07
AD1B8A34 A2877711 E33A613D 8E50AE40 A106DE9C B2B03B95 73392ADB 4BB51FAD
6F2D6F8D A90BA0B5 BD1A209C F54126A9 2E2FF5B7 85041B7E C72032C0 CECE7F79
51550203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 141713AB B7F927E5 50C242DF 9912C3B6 61D93313 80301D06
03551D0E 04160414 1713ABB7 F927E550 C242DF99 12C3B661 D9331380 300D0609
2A864886 F70D0101 05050003 81810099 8EBE5630 2E6734A8 4D2FD0A5 F09A98F8
9E49125F AECEF4BB E0DEBB3A 1A449E38 99B02114 7EC84845 B53C2F88 046B7290
AE44967A 8BE20F5E 9D4A1CFC E1F64FE8 59F51892 23B88B4E 3416808A 68E65660
644C7DA0 E3A7A525 14FE8E54 67C35F8E CF69EB40 34DFB13D EA302F66 102C822A
3D7107BA AA4E7273 1D43690E C4A5D4
quit
crypto pki certificate chain test_trustpoint_config_created_for_sdm
no ip source-route
ip dhcp excluded-address 192.168.0.230 192.168.0.255
ip dhcp excluded-address 192.168.0.1 192.168.0.200
ip dhcp pool QQQ_LAN
import all
network 192.168.0.0 255.255.255.0
default-router 192.168.0.254
dns-server 192.168.0.6 202.1.161.36
netbios-name-server 192.168.0.6
domain-name QQQ.Local
lease 3
ip cef
no ip bootp server
ip domain name QQQ.Local
ip name-server 192.168.0.6
ip name-server 202.1.161.37
ip name-server 202.1.161.36
ip inspect log drop-pkt
no ipv6 cef
parameter-map type inspect global
log dropped-packets enable
parameter-map type protocol-info yahoo-servers
server name scs.msg.yahoo.com
server name scsa.msg.yahoo.com
server name scsb.msg.yahoo.com
server name scsc.msg.yahoo.com
server name scsd.msg.yahoo.com
server name cs16.msg.dcn.yahoo.com
server name cs19.msg.dcn.yahoo.com
server name cs42.msg.dcn.yahoo.com
server name cs53.msg.dcn.yahoo.com
server name cs54.msg.dcn.yahoo.com
server name ads1.vip.scd.yahoo.com
server name radio1.launch.vip.dal.yahoo.com
server name in1.msg.vip.re2.yahoo.com
server name data1.my.vip.sc5.yahoo.com
server name address1.pim.vip.mud.yahoo.com
server name edit.messenger.yahoo.com
server name messenger.yahoo.com
server name http.pager.yahoo.com
server name privacy.yahoo.com
server name csa.yahoo.com
server name csb.yahoo.com
server name csc.yahoo.com
parameter-map type protocol-info aol-servers
server name login.oscar.aol.com
server name toc.oscar.aol.com
server name oam-d09a.blue.aol.com
parameter-map type protocol-info msn-servers
server name messenger.hotmail.com
server name gateway.messenger.hotmail.com
server name webmessenger.msn.com
password encryption aes
license udi pid CISCO887VA-K9 sn FGL162321CT
object-group service MAIL-PORTS
description QQQ User Mail Restrictions
tcp eq smtp
tcp eq pop3
tcp eq 995
tcp eq 993
udp lt rip
udp lt domain
tcp eq telnet
udp lt ntp
udp lt tftp
tcp eq ftp
tcp eq domain
tcp eq 5900
tcp eq ftp-data
tcp eq 3389
tcp eq 20410
object-group network Network1
description QQQ Management Network
192.168.1.0 255.255.255.0
192.168.4.0 255.255.255.0
192.168.5.0 255.255.255.0
192.168.7.0 255.255.255.0
192.168.8.0 255.255.255.0
range 192.168.0.200 192.168.0.254
range 192.168.0.1 192.168.0.25
object-group network Network2
description QQQ User Network
192.168.2.0 255.255.255.0
192.168.3.0 255.255.255.0
192.168.6.0 255.255.255.0
range 192.168.0.26 192.168.0.199
object-group network QQQ.Local
description QQQ_Domain
192.168.0.0 255.255.255.0
192.168.1.0 255.255.255.0
192.168.2.0 255.255.255.0
192.168.3.0 255.255.255.0
192.168.4.0 255.255.255.0
192.168.5.0 255.255.255.0
192.168.6.0 255.255.255.0
192.168.8.0 255.255.255.0
192.168.7.0 255.255.255.0
192.168.10.0 255.255.255.0
10.1.0.0 255.255.0.0
object-group network QQQ_Management_Group
description QQQ I.T. Devices With UnRestricted Access
range 192.168.0.200 192.168.0.254
range 192.168.0.1 192.168.0.25
192.168.1.0 255.255.255.0
192.168.8.0 255.255.255.0
192.168.7.0 255.255.255.0
192.168.5.0 255.255.255.0
192.168.4.0 255.255.255.0
10.1.0.0 255.255.0.0
192.168.10.0 255.255.255.0
10.8.0.0 255.255.255.0
192.168.9.0 255.255.255.0
192.168.100.0 255.255.255.0
192.168.20.0 255.255.255.0
192.168.21.0 255.255.255.0
192.168.22.0 255.255.255.0
192.168.23.0 255.255.255.0
object-group network QQQ_User_Group
description QQQ I.T. Devices WIth Restricted Access
range 192.168.0.26 192.168.0.199
192.168.2.0 255.255.255.0
192.168.3.0 255.255.255.0
192.168.6.0 255.255.255.0
object-group service WEB
description QQQ User Web Restrictions
tcp eq www
tcp eq 443
tcp eq 8080
tcp eq 1863
tcp eq 5190
username cpadmin privilege 15 password 7 1406031A2C172527
username QQQVPN privilege 15 secret 4 Hk2tP2GgJ1xXtJUqIZr4gmNSgw6q1E.rvzWiYnDAZHU
controller VDSL 0
ip tcp synwait-time 10
no ip ftp passive
class-map type inspect match-all sdm-cls-VPNOutsideToInside-1
match access-group 118
class-map type inspect match-all sdm-cls-VPNOutsideToInside-3
match access-group 121
class-map type inspect match-all sdm-cls-VPNOutsideToInside-2
match access-group 120
class-map type inspect imap match-any ccp-app-imap
match invalid-command
class-map type inspect match-any ccp-cls-protocol-p2p
match protocol edonkey signature
match protocol gnutella signature
match protocol kazaa2 signature
match protocol fasttrack signature
match protocol bittorrent signature
class-map type inspect match-all sdm-cls-VPNOutsideToInside-4
match access-group 122
class-map type inspect match-all SDM_GRE
match access-group name SDM_GRE
class-map type inspect match-any CCP_PPTP
match class-map SDM_GRE
class-map type inspect match-any SDM_AH
match access-group name SDM_AH
class-map type inspect match-any ccp-skinny-inspect
match protocol skinny
class-map type inspect match-any SDM_ESP
match access-group name SDM_ESP
class-map type inspect match-any SDM_VPN_TRAFFIC
match protocol isakmp
match protocol ipsec-msft
match class-map SDM_AH
match class-map SDM_ESP
class-map type inspect match-all SDM_VPN_PT
match access-group 117
match class-map SDM_VPN_TRAFFIC
class-map type inspect match-any ccp-cls-insp-traffic
match protocol pptp
match protocol dns
match protocol ftp
match protocol https
match protocol icmp
match protocol imap
match protocol pop3
match protocol netshow
match protocol shell
match protocol realmedia
match protocol rtsp
match protocol smtp
match protocol sql-net
match protocol streamworks
match protocol tftp
match protocol vdolive
match protocol tcp
match protocol udp
class-map type inspect match-all ccp-insp-traffic
match class-map ccp-cls-insp-traffic
class-map type inspect match-any SDM_IP
match access-group name SDM_IP
class-map type inspect gnutella match-any ccp-app-gnutella
match file-transfer
class-map type inspect match-any SDM_HTTP
match access-group name SDM_HTTP
class-map type inspect match-any SDM_EASY_VPN_SERVER_TRAFFIC
match protocol isakmp
match protocol ipsec-msft
match class-map SDM_AH
match class-map SDM_ESP
class-map type inspect match-all SDM_EASY_VPN_SERVER_PT
match class-map SDM_EASY_VPN_SERVER_TRAFFIC
class-map type inspect match-all sdm-cls-http
match access-group name dmz-traffic
match protocol http
class-map type inspect match-any Telnet
match protocol telnet
class-map type inspect msnmsgr match-any ccp-app-msn-otherservices
match service any
class-map type inspect ymsgr match-any ccp-app-yahoo-otherservices
match service any
class-map type inspect match-any ccp-h323nxg-inspect
match protocol h323-nxg
class-map type inspect match-any ccp-cls-icmp-access
match protocol icmp
match protocol tcp
match protocol udp
class-map type inspect match-any ccp-cls-protocol-im
match protocol ymsgr yahoo-servers
match protocol msnmsgr msn-servers
match protocol aol aol-servers
class-map type inspect aol match-any ccp-app-aol-otherservices
match service any
class-map type inspect match-all ccp-protocol-pop3
match protocol pop3
class-map type inspect match-any ccp-h225ras-inspect
match protocol h225ras
class-map type inspect match-any FIREWALL_EXCEPTIONS_CLASS
match access-group name FIREWALL_EXCEPTIONS_ACL
class-map type inspect match-any ccp-h323annexe-inspect
match protocol h323-annexe
class-map type inspect match-any SDM_EASY_VPN_CTCP_SERVER_PT
match access-group 102
match access-group 103
match access-group 104
match access-group 105
match access-group 106
match access-group 107
match access-group 108
match access-group 109
match access-group 110
match access-group 111
match access-group 112
match access-group 113
match access-group 114
match access-group 115
class-map type inspect match-any SIP
match protocol sip
class-map type inspect pop3 match-any ccp-app-pop3
class-map type inspect match-any SDM_HTTPS
match access-group name SDM_HTTPS
class-map type inspect sip match-any ccp-cls-sip-pv-2
match protocol-violation
class-map type inspect kazaa2 match-any ccp-app-kazaa2
match file-transfer
class-map type inspect match-all ccp-protocol-p2p
match class-map ccp-cls-protocol-p2p
class-map type inspect match-all ccp-cls-ccp-permit-1
match access-group name ETS1
class-map type inspect match-any ccp-h323-inspect
match protocol h323
class-map type inspect msnmsgr match-any ccp-app-msn
match service text-chat
class-map type inspect ymsgr match-any ccp-app-yahoo
match service text-chat
class-map type inspect match-all ccp-cls-ccp-pol-outToIn-1
match access-group name ETS
class-map type inspect match-all ccp-protocol-im
match class-map ccp-cls-protocol-im
class-map type inspect match-all ccp-cls-ccp-pol-outToIn-2
match class-map Telnet
match access-group name Telnet
class-map type inspect match-all ccp-icmp-access
match class-map ccp-cls-icmp-access
class-map type inspect match-all ccp-invalid-src
match access-group 100
class-map type inspect http match-any ccp-app-httpmethods
match request method bcopy
match request method bdelete
match request method bmove
match request method bpropfind
match request method bproppatch
match request method connect
match request method copy
match request method delete
match request method edit
match request method getattribute
match request method getattributenames
match request method getproperties
match request method index
match request method lock
match request method mkcol
match request method mkdir
match request method move
match request method notify
match request method options
match request method poll
match request method propfind
match request method proppatch
match request method put
match request method revadd
match request method revlabel
match request method revlog
match request method revnum
match request method save
match request method search
match request method setattribute
match request method startrev
match request method stoprev
match request method subscribe
match request method trace
match request method unedit
match request method unlock
match request method unsubscribe
class-map type inspect match-any ccp-dmz-protocols
match user-group qqq
match protocol icmp
match protocol http
class-map type inspect edonkey match-any ccp-app-edonkey
match file-transfer
match text-chat
match search-file-name
class-map type inspect match-any ccp-sip-inspect
match protocol sip
class-map type inspect match-all sdm-cls-sip
match access-group name dmz-traffic
match protocol sip
class-map type inspect match-all ccp-dmz-traffic
match access-group name dmz-traffic
match class-map ccp-dmz-protocols
class-map type inspect http match-any ccp-http-blockparam
match request port-misuse im
match request port-misuse p2p
class-map type inspect edonkey match-any ccp-app-edonkeydownload
match file-transfer
class-map type inspect match-all ccp-protocol-imap
match protocol imap
class-map type inspect aol match-any ccp-app-aol
match service text-chat
class-map type inspect edonkey match-any ccp-app-edonkeychat
match search-file-name
match text-chat
class-map type inspect match-all ccp-cls-ccp-permit-dmzservice-1
match class-map SIP
match access-group name SIP
class-map type inspect fasttrack match-any ccp-app-fasttrack
match file-transfer
class-map type inspect http match-any ccp-http-allowparam
match request port-misuse tunneling
class-map type inspect match-all ccp-protocol-http
match protocol http
policy-map type inspect ccp-permit-icmpreply
class type inspect ccp-icmp-access
inspect
class class-default
pass
policy-map type inspect p2p ccp-action-app-p2p
class type inspect edonkey ccp-app-edonkeychat
log
allow
class type inspect edonkey ccp-app-edonkeydownload
log
allow
class type inspect fasttrack ccp-app-fasttrack
log
allow
class type inspect gnutella ccp-app-gnutella
log
allow
class type inspect kazaa2 ccp-app-kazaa2
log
allow
policy-map type inspect PF_OUT_TO_IN
class type inspect FIREWALL_EXCEPTIONS_CLASS
pass
policy-map type inspect PF_IN_TO_OUT
class type inspect FIREWALL_EXCEPTIONS_CLASS
pass
policy-map type inspect im ccp-action-app-im
class type inspect aol ccp-app-aol
log
allow
class type inspect msnmsgr ccp-app-msn
log
allow
class type inspect ymsgr ccp-app-yahoo
log
allow
class type inspect aol ccp-app-aol-otherservices
log
reset
class type inspect msnmsgr ccp-app-msn-otherservices
log
reset
class type inspect ymsgr ccp-app-yahoo-otherservices
log
reset
policy-map type inspect http ccp-action-app-http
class type inspect http ccp-http-blockparam
log
reset
class type inspect http ccp-app-httpmethods
log
reset
class type inspect http ccp-http-allowparam
log
allow
policy-map type inspect imap ccp-action-imap
class type inspect imap ccp-app-imap
log
policy-map type inspect pop3 ccp-action-pop3
class type inspect pop3 ccp-app-pop3
log
policy-map type inspect ccp-inspect
class type inspect ccp-protocol-http
inspect
service-policy http ccp-action-app-http
class type inspect ccp-protocol-imap
inspect
service-policy imap ccp-action-imap
class type inspect ccp-protocol-pop3
inspect
service-policy pop3 ccp-action-pop3
class type inspect ccp-protocol-p2p
inspect
service-policy p2p ccp-action-app-p2p
class type inspect ccp-protocol-im
inspect
service-policy im ccp-action-app-im
class type inspect ccp-insp-traffic
inspect
class type inspect ccp-sip-inspect
inspect
class type inspect ccp-h323-inspect
inspect
class type inspect ccp-h323annexe-inspect
inspect
class type inspect ccp-h225ras-inspect
inspect
class type inspect ccp-h323nxg-inspect
inspect
class type inspect ccp-skinny-inspect
inspect
class type inspect ccp-invalid-src
drop log
class class-default
drop
policy-map type inspect ccp-permit
class type inspect SDM_VPN_PT
pass
class type inspect ccp-cls-ccp-permit-1
pass
class type inspect SDM_EASY_VPN_SERVER_PT
pass
class type inspect SDM_EASY_VPN_CTCP_SERVER_PT
inspect
class class-default
drop
policy-map type inspect sip ccp-app-sip-2
class type inspect sip ccp-cls-sip-pv-2
allow
policy-map type inspect ccp-permit-dmzservice
class type inspect ccp-cls-ccp-permit-dmzservice-1
pass
class type inspect ccp-dmz-traffic
inspect
class type inspect sdm-cls-http
inspect
service-policy http ccp-action-app-http
class type inspect sdm-cls-VPNOutsideToInside-1
inspect
class type inspect sdm-cls-VPNOutsideToInside-2
inspect
class type inspect sdm-cls-VPNOutsideToInside-3
pass
class class-default
pass
policy-map type inspect ccp-pol-outToIn
class type inspect ccp-cls-ccp-pol-outToIn-1
pass
class type inspect ccp-cls-ccp-pol-outToIn-2
pass
class type inspect CCP_PPTP
pass
class type inspect sdm-cls-VPNOutsideToInside-1
inspect
class type inspect sdm-cls-VPNOutsideToInside-2
inspect
class type inspect sdm-cls-VPNOutsideToInside-3
pass
class type inspect sdm-cls-VPNOutsideToInside-4
inspect
class class-default
drop log
policy-map type inspect sdm-permit-ip
class type inspect SDM_IP
pass
class type inspect sdm-cls-VPNOutsideToInside-2
inspect
class type inspect sdm-cls-VPNOutsideToInside-3
pass
class type inspect sdm-cls-VPNOutsideToInside-4
inspect
class class-default
drop log
zone security dmz-zone
zone security in-zone
zone security out-zone
zone security ezvpn-zone
zone-pair security ccp-zp-out-dmz source out-zone destination dmz-zone
service-policy type inspect ccp-permit-dmzservice
zone-pair security ccp-zp-out-self source out-zone destination self
service-policy type inspect ccp-permit
zone-pair security ccp-zp-in-out source in-zone destination out-zone
service-policy type inspect ccp-inspect
zone-pair security ccp-zp-out-zone-To-in-zone source out-zone destination in-zone
service-policy type inspect ccp-pol-outToIn
zone-pair security ccp-zp-in-dmz source in-zone destination dmz-zone
service-policy type inspect ccp-permit-dmzservice
zone-pair security ccp-zp-self-out source self destination out-zone
service-policy type inspect ccp-permit-icmpreply
zone-pair security dmz-to-in source dmz-zone destination in-zone
service-policy type inspect ccp-permit-icmpreply
zone-pair security sdm-zp-ezvpn-out1 source ezvpn-zone destination out-zone
service-policy type inspect sdm-permit-ip
zone-pair security sdm-zp-in-ezvpn2 source in-zone destination ezvpn-zone
service-policy type inspect sdm-permit-ip
zone-pair security sdm-zp-in-ezvpn1 source dmz-zone destination ezvpn-zone
service-policy type inspect sdm-permit-ip
zone-pair security sdm-zp-ezvpn-in2 source ezvpn-zone destination in-zone
service-policy type inspect sdm-permit-ip
zone-pair security sdm-zp-ezvpn-in1 source ezvpn-zone destination dmz-zone
service-policy type inspect sdm-permit-ip
zone-pair security sdm-zp-out-ezpn1 source out-zone destination ezvpn-zone
service-policy type inspect sdm-permit-ip
zone-pair security sdm-zp-ezvpn-in3 source ezvpn-zone destination ezvpn-zone
service-policy type inspect sdm-permit-ip
crypto ctcp port 10000 1723 6299
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp policy 2
encr aes 256
authentication pre-share
group 2
crypto isakmp key 6 PbKM_WfaCM[hYNXAFOUgCNgCB_ZdJEAAB address 220.245.109.219
crypto isakmp key 6 NddQRR[O^KY`GRDC[VZUEPE`CSJ^CDAAB address 0.0.0.0 0.0.0.0
crypto isakmp client configuration group QQQ
key 6 UWVBhb`Lgc_AZbDYWDFZiGZTTadNYTAAB
dns 192.168.0.6 202.1.161.36
wins 192.168.0.6
domain QQQ.Local
pool SDM_POOL_1
include-local-lan
max-users 20
max-logins 1
netmask 255.255.255.0
banner ^CCWelcome to QQQ VPN!!!!1 ^C
crypto isakmp profile ciscocp-ike-profile-1
match identity group QQQ
client authentication list ciscocp_vpn_xauth_ml_1
isakmp authorization list ciscocp_vpn_group_ml_1
client configuration address initiate
client configuration address respond
keepalive 10 retry 2
virtual-template 1
crypto ipsec transform-set ESP_AES_SHA esp-aes 256 esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec profile CiscoCP_Profile1
set security-association idle-time 43200
set transform-set ESP_AES_SHA
set isakmp-profile ciscocp-ike-profile-1
crypto map SDM_CMAP_1 1 ipsec-isakmp
description Tunnel to220.245.109.219
set peer 220.245.109.219
set transform-set ESP-3DES-SHA
match address 119
interface Loopback0
description QQQ_VPN
ip address 192.168.9.254 255.255.255.0
interface Null0
no ip unreachables
interface Ethernet0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
shutdown
no fair-queue
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
no atm ilmi-keepalive
interface ATM0.1 point-to-point
description Telekom_ADSL
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
zone-member security out-zone
pvc 8/35
pppoe-client dial-pool-number 1
interface FastEthernet0
description QQQ_LAN-VLAN_1
switchport access vlan 1
no ip address
interface FastEthernet1
description QQQ_LAN-VLAN_1
no ip address
interface FastEthernet2
description QQQ_WAN-VLAN_2
switchport access vlan 2
no ip address
interface FastEthernet3
description QQQ_DMZ-IP_PBX-VLAN_3
switchport access vlan 3
no ip address
interface Virtual-Template1 type tunnel
description QQQ_Easy_VPN
ip unnumbered Loopback0
ip nat inside
ip virtual-reassembly in
zone-member security ezvpn-zone
tunnel mode ipsec ipv4
tunnel protection ipsec profile CiscoCP_Profile1
interface Vlan1
description QQQ_LAN-VLAN1$FW_INSIDE$
ip address 192.168.0.254 255.255.255.0
ip access-group QQQ_ACL in
ip mask-reply
ip nat inside
ip virtual-reassembly in
zone-member security in-zone
ip tcp adjust-mss 1412
interface Vlan2
description QQQ_WAN-VLAN2$FW_INSIDE$
ip address 192.168.5.254 255.255.255.0
ip access-group QQQ_ACL in
ip mask-reply
ip nat inside
ip virtual-reassembly in
zone-member security in-zone
ip tcp adjust-mss 1412
interface Vlan3
description QQQ_IP-PBX_WAN-VLAN3
ip address 192.168.4.254 255.255.255.0
ip mask-reply
ip nat inside
ip virtual-reassembly in
zone-member security dmz-zone
interface Vlan4
description VLAN4 - 192.168.20.xxx (Spare)
ip address 192.168.20.253 255.255.255.0
ip nat inside
ip virtual-reassembly in
zone-member security in-zone
interface Dialer0
description ATM Dialer
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip virtual-reassembly in
zone-member security out-zone
no cdp enable
interface Dialer2
description $FW_OUTSIDE$
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1452
ip nbar protocol-discovery
ip flow ingress
ip flow egress
ip nat outside
ip virtual-reassembly in
zone-member security out-zone
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxxxxxxxxxxxxxxxxxx
ppp chap password 7 xxxxxxxxxxxxxxxxxxxxxxxxx
ppp pap sent-username xxxxxxxxxx0 password 7 xxxxxxxxxxxxxxxxxxxxx
no cdp enable
crypto map SDM_CMAP_1
router rip
version 2
redistribute static
passive-interface ATM0
passive-interface ATM0.1
passive-interface Dialer0
passive-interface Dialer2
passive-interface Ethernet0
passive-interface Loopback0
network 10.0.0.0
network 192.168.0.0
network 192.168.1.0
network 192.168.2.0
network 192.168.3.0
network 192.168.4.0
network 192.168.5.0
network 192.168.6.0
network 192.168.7.0
network 192.168.8.0
network 192.168.10.0
network 192.168.100.0
ip local pool SDM_POOL_1 192.168.5.100 192.168.5.200
ip forward-protocol nd
ip http server
ip http access-class 5
ip http authentication local
ip http secure-server
ip nat pool NAT_IP 192.168.0.210 192.168.0.235 netmask 255.255.255.0
ip nat inside source static tcp 192.168.4.253 5060 interface Dialer2 5060
ip nat inside source static tcp 192.168.0.240 20408 interface Dialer2 6208
ip nat inside source static tcp 192.168.0.240 20409 interface Dialer2 6209
ip nat inside source static tcp 192.168.0.240 20410 interface Dialer2 6200
ip nat inside source static tcp 192.168.1.240 20408 interface Dialer2 6218
ip nat inside source static tcp 192.168.1.240 20409 interface Dialer2 6219
ip nat inside source static tcp 192.168.1.240 20410 interface Dialer2 6210
ip nat inside source static tcp 192.168.7.240 20408 interface Dialer2 6278
ip nat inside source static tcp 192.168.7.240 20409 interface Dialer2 6279
ip nat inside source static tcp 192.168.7.240 20410 interface Dialer2 6270
ip nat inside source static tcp 192.168.8.240 20408 interface Dialer2 6288
ip nat inside source static tcp 192.168.8.240 20409 interface Dialer2 6289
ip nat inside source static tcp 192.168.8.240 20410 interface Dialer2 6280
ip nat inside source static tcp 192.168.0.6 1723 interface Dialer2 1723
ip nat inside source static tcp 192.168.0.6 3389 interface Dialer2 6389
ip nat inside source static tcp 192.168.0.24 3389 interface Dialer2 6390
ip nat inside source static tcp 192.168.4.253 8022 interface Dialer2 8022
ip nat inside source static tcp 192.168.4.253 80 interface Dialer2 8021
ip nat inside source static tcp 192.168.0.254 23 interface Dialer2 8023
ip nat inside source static tcp 192.168.0.6 443 interface Dialer2 443
ip nat inside source route-map SDM_RMAP_1 interface Dialer2 overload
ip default-network 192.168.0.0
ip default-network 192.168.4.0
ip route 0.0.0.0 0.0.0.0 Dialer2 permanent
ip route 10.1.0.0 255.255.0.0 Vlan2 permanent
ip route 10.8.0.0 255.255.255.0 Vlan2 permanent
ip route 192.168.0.0 255.255.255.0 Vlan1 permanent
ip route 192.168.4.0 255.255.255.0 Vlan3 permanent
ip route 192.168.5.0 255.255.255.0 Vlan2 permanent
ip route 192.168.100.0 255.255.255.0 Dialer2 permanent
ip access-list extended ACCESS_FROM_INSIDE
permit ip object-group QQQ_Management_Group any
permit tcp object-group QQQ_User_Group any eq smtp pop3
permit tcp object-group QQQ_User_Group any eq 993 995
permit tcp 192.168.0.0 0.0.0.255 any eq smtp pop3
permit tcp 192.168.0.0 0.0.0.255 any eq 993 995
permit ip 192.168.1.0 0.0.0.255 any
permit ip 192.168.4.0 0.0.0.255 any
permit ip 192.168.5.0 0.0.0.255 any
permit ip 192.168.7.0 0.0.0.255 any
permit ip 192.168.8.0 0.0.0.255 any
permit tcp 192.168.2.0 0.0.0.255 any eq www 443 8080 domain
permit tcp 192.168.2.0 0.0.0.255 any eq www 443 8080 domain time-range QQQ_Control
permit tcp 192.168.3.0 0.0.0.255 any eq www 443 8080 domain time-range QQQ_Control
permit tcp 192.168.4.0 0.0.0.255 any eq www 443 8080 domain time-range QQQ_Control
permit udp 192.168.2.0 0.0.0.255 any eq domain time-range QQQ_Control
permit udp 192.168.3.0 0.0.0.255 any eq domain time-range QQQ_Control
permit udp 192.168.4.0 0.0.0.255 any eq domain time-range QQQ_Control
ip access-list extended ETS
remark CCP_ACL Category=128
permit ip host 203.219.237.252 any
ip access-list extended ETS1
remark CCP_ACL Category=128
permit ip host 203.219.237.252 any
ip access-list extended FIREWALL_EXCEPTIONS_ACL
permit tcp any host 192.168.0.100 eq 25565
permit tcp any eq 25565 host 192.168.0.100
ip access-list extended QQQ_ACL
permit ip any host 192.168.4.253
permit udp any any eq bootps bootpc
permit ip any 192.168.4.0 0.0.0.255
permit ip host 203.219.237.252 any
remark QQQ Internet Control List
remark CCP_ACL Category=17
remark Auto generated by CCP for NTP (123) 203.12.160.2
permit udp host 203.12.160.2 eq ntp any eq ntp
remark AD Services
permit udp host 192.168.0.6 eq domain any
remark Unrestricted Access
permit ip object-group QQQ_Management_Group any
remark Restricted Users
permit object-group MAIL-PORTS object-group QQQ_User_Group any
permit ip 192.168.0.0 0.0.0.255 any time-range QQQ_Control
permit ip 192.168.2.0 0.0.0.255 any time-range QQQ_Control
permit ip 192.168.3.0 0.0.0.255 any time-range QQQ_Control
permit ip 192.168.6.0 0.0.0.255 any time-range QQQ_Control
remark ICMP Full Access
permit icmp object-group QQQ_User_Group any
permit tcp 192.168.2.0 0.0.0.255 eq www 443 8080 5190 1863 any time-range QQQ_Control
permit tcp 192.168.3.0 0.0.0.255 eq www 443 8080 5190 1863 any time-range QQQ_Control
permit tcp 192.168.6.0 0.0.0.255 eq www 443 8080 5190 1863 any time-range QQQ_Control
permit udp 192.168.6.0 0.0.0.255 eq 80 443 8080 5190 1863 any time-range QQQ_Control
permit tcp 192.168.0.0 0.0.0.255 eq www 443 8080 5190 1863 any time-range QQQ_Control
permit udp 192.168.0.0 0.0.0.255 eq 80 443 8080 5190 1863 any time-range QQQ_Control
permit udp 192.168.2.0 0.0.0.255 eq 80 443 8080 5190 1863 any time-range QQQ_Control
permit udp 192.168.3.0 0.0.0.255 eq 80 443 8080 5190 1863 any time-range QQQ_Control
ip access-list extended QQQ_NAT
remark CCP_ACL Category=18
remark IPSec Rule
deny ip 192.168.0.0 0.0.255.255 192.168.100.0 0.0.0.255
permit ip any any
ip access-list extended SDM_AH
remark CCP_ACL Category=1
permit ahp any any
ip access-list extended SDM_ESP
remark CCP_ACL Category=1
permit esp any any
ip access-list extended SDM_GRE
remark CCP_ACL Category=1
permit gre any any
ip access-list extended SDM_HTTP
remark CCP_ACL Category=0
permit tcp any any eq telnet
ip access-list extended SDM_HTTPS
remark CCP_ACL Category=0
permit tcp any any eq 443
ip access-list extended SDM_IP
remark CCP_ACL Category=1
permit ip any any
ip access-list extended SIP
remark CCP_ACL Category=128
permit ip any 192.168.4.0 0.0.0.255
ip access-list extended Telnet
remark CCP_ACL Category=128
permit ip any any
ip access-list extended dmz-traffic
remark CCP_ACL Category=1
permit ip any 192.168.4.0 0.0.0.255
access-list 1 remark CCP_ACL Category=2
access-list 1 remark QQQ_DMZ
access-list 1 permit 192.168.4.0 0.0.0.255
access-list 2 remark CCP_ACL Category=2
access-list 2 remark QQQ_LAN
access-list 2 permit 192.168.0.0 0.0.0.255
access-list 3 remark QQQ Insid NAT
access-list 3 remark CCP_ACL Category=2
access-list 3 permit 192.168.0.0 0.0.0.255
access-list 3 permit 192.168.1.0 0.0.0.255
access-list 3 permit 192.168.2.0 0.0.0.255
access-list 3 permit 192.168.3.0 0.0.0.255
access-list 3 permit 192.168.4.0 0.0.0.255
access-list 3 permit 192.168.5.0 0.0.0.255
access-list 3 permit 192.168.6.0 0.0.0.255
access-list 3 permit 192.168.7.0 0.0.0.255
access-list 3 permit 192.168.8.0 0.0.0.255
access-list 3 permit 192.168.9.0 0.0.0.255
access-list 3 permit 192.168.10.0 0.0.0.255
access-list 4 remark QQQ_NAT
access-list 4 remark CCP_ACL Category=2
access-list 4 permit 10.1.0.0 0.0.255.255
access-list 4 permit 10.8.0.0 0.0.0.255
access-list 4 permit 192.168.0.0 0.0.0.255
access-list 4 permit 192.168.1.0 0.0.0.255
access-list 4 permit 192.168.2.0 0.0.0.255
access-list 4 permit 192.168.3.0 0.0.0.255
access-list 4 permit 192.168.4.0 0.0.0.255
access-list 4 permit 192.168.5.0 0.0.0.255
access-list 4 permit 192.168.6.0 0.0.0.255
access-list 4 permit 192.168.7.0 0.0.0.255
access-list 4 permit 192.168.8.0 0.0.0.255
access-list 4 permit 192.168.9.0 0.0.0.255
access-list 4 permit 192.168.10.0 0.0.0.255
access-list 5 remark HTTP Access-class list
access-list 5 remark CCP_ACL Category=1
access-list 5 permit 192.168.4.0 0.0.0.255
access-list 5 permit 192.168.0.0 0.0.0.255
access-list 5 deny any
access-list 100 remark CCP_ACL Category=128
access-list 100 permit ip 192.168.4.0 0.0.0.255 any
access-list 100 permit ip 127.0.0.0 0.255.255.255 any
access-list 100 permit ip host 255.255.255.255 any
access-list 101 remark QQQ_Extended_ACL
access-list 101 remark CCP_ACL Category=1
access-list 101 permit tcp any host 192.168.0.254 eq 10000
access-list 101 permit udp any host 192.168.0.254 eq non500-isakmp
access-list 101 permit udp any host 192.168.0.254 eq isakmp
access-list 101 permit esp any host 192.168.0.254
access-list 101 permit ahp any host 192.168.0.254
access-list 101 remark Auto generated by CCP for NTP (123) 203.12.160.2
access-list 101 permit udp host 203.12.160.2 eq ntp host 192.168.4.254 eq ntp
access-list 101 permit udp host 192.168.0.6 eq domain any
access-list 101 remark NTP (123) 203.12.160.2
access-list 101 permit udp host 203.12.160.2 eq ntp any eq ntp
access-list 101 remark QQQ_ANY_Any
access-list 101 permit ip object-group QQQ.Local any
access-list 101 remark QQQ_DMZ
access-list 101 permit ip any 192.168.4.0 0.0.0.255
access-list 101 remark QQQ_GRE
access-list 101 permit gre any any
access-list 101 remark QQQ_Ping
access-list 101 permit icmp any any
access-list 102 remark CCP_ACL Category=1
access-list 102 permit tcp any any eq 10000
access-list 103 permit tcp any 192.168.0.0 0.0.0.255 eq 443
access-list 103 remark CCP_ACL Category=1
access-list 103 permit tcp any any eq 10000
access-list 103 permit tcp any 192.168.4.0 0.0.0.255 eq 8022
access-list 103 permit tcp any 192.168.4.0 0.0.0.255 eq telnet
access-list 103 permit tcp any 192.168.4.0 0.0.0.255 eq www
access-list 103 permit tcp any 192.168.4.0 0.0.0.255 eq 5060
access-list 103 permit tcp any eq telnet host 192.168.0.254
access-list 103 permit tcp any 192.168.0.0 0.0.0.255 eq telnet
access-list 103 permit udp any 192.168.4.0 0.0.0.255 eq 5060
access-list 103 permit udp any 192.168.4.0 0.0.0.255 range 10001 12000
access-list 104 remark CCP_ACL Category=1
access-list 104 permit tcp any any eq 10000
access-list 105 remark CCP_ACL Category=1
access-list 105 permit tcp any any eq 10000
access-list 106 remark CCP_ACL Category=1
access-list 106 permit tcp any any eq 10000
access-list 107 remark CCP_ACL Category=1
access-list 107 permit tcp any any eq 10000
access-list 108 remark CCP_ACL Category=1
access-list 108 permit tcp any any eq 10000
access-list 109 remark CCP_ACL Category=1
access-list 109 permit tcp any any eq 10000
access-list 110 remark CCP_ACL Category=1
access-list 110 permit tcp any any eq 10000
access-list 111 remark CCP_ACL Category=1
access-list 111 permit tcp any any eq 10000
access-list 112 remark CCP_ACL Category=1
access-list 112 permit tcp any any eq 10000
access-list 113 remark CCP_ACL Category=1
access-list 113 permit tcp any any eq 10000
access-list 114 remark CCP_ACL Category=1
access-list 114 permit tcp any any eq 10000
access-list 115 remark CCP_ACL Category=1
access-list 115 permit tcp any any eq 10000
access-list 116 remark CCP_ACL Category=4
access-list 116 remark IPSec Rule
access-list 116 permit ip 192.168.0.0 0.0.255.255 192.168.100.0 0.0.0.255
access-list 117 remark CCP_ACL Category=128
access-list 117 permit ip any any
access-list 117 permit ip host 220.245.109.219 any
access-list 118 remark CCP_ACL Category=0
access-list 118 permit ip 192.168.100.0 0.0.0.255 192.168.0.0 0.0.0.255
access-list 119 remark CCP_ACL Category=4
access-list 119 remark IPSec Rule
access-list 119 permit ip 192.168.0.0 0.0.255.255 192.168.100.0 0.0.0.255
access-list 120 remark CCP_ACL Category=0
access-list 120 permit ip 192.168.100.0 0.0.0.255 192.168.0.0 0.0.0.255
access-list 121 remark CCP_ACL Category=0
access-list 121 permit ip 192.168.100.0 0.0.0.255 192.168.0.0 0.0.255.255
access-list 122 remark CCP_ACL Category=0
access-list 122 permit ip 192.168.100.0 0.0.0.255 192.168.0.0 0.0.255.255
dialer-list 1 protocol ip permit
route-map SDM_RMAP_1 permit 1
match ip address QQQ_NAT
banner login ^CCWelcome to QQQ ADSL GatewayIt turns out the problem had nothing to do with wires or splitters. The Verizon tech was at my house yesterday and the ONT was failing. He replaced part of the ONT and it fixed the problem (finally!). At least I was able to watch the Celtics game last night.
I have a Tellabs ONT. Not sure the model but it's older like the ones in this thread.
http://www.dslreports.com/forum/r19982000-Mounting-board-for-612-ONT -
Port Forwarding To Two Macs with Port 22 limitations
This is another port forwarding/port 22 issue and I've look around and not seen an answer to my specific problem. I work for a business that has an in-house ad system that runs on a Mac Mini. I have been accessing that Mac Mini remotely because we set up port forwarding through the Linksys rounter that is at the business using port 22. This is the only port that works for this connection to the mini and the software.
We are now adding a second Mac Mini to send the ads to a different set of monitors. I can't set up port forward to the new mini on the same port so I don't know how to connect to this mini remotely. Is there a way to get into the first mini through port 22 and then somehow communite to the second one through the first? Is there another way to do port forwarding...or have the linksys router switch from one mini to the other when a request comes in? There will only be one remote computer trying to reach either Mac Mini so there will never be simultaneous traffic coming in. Any help would be appreciated!
The linksys router is critical to the business becasue a host of other devices are forwarded though it as well.
Thank you.klara wrote:
Having set up my IP camera with HH4 successfully, I've now got another one and would like to set it up as well. I gave it a unique, static IP address which my router can see fine. When I try to set up port forwarding, I get a message saying:
"The game or application you’ve selected conflicts with an application (IP Cam 1) you’ve already assigned to another device. Please remove the other application or select the same device."
I am not being given the option to select the same device.
I'm now wondering if port forwarding to two identical devices actually works in principle with HH4? Has anyone else done this?
If in the Home Hub 4 A you go to
Advanced Settings
Firewall
Port Fowarding
Manage Games and Applications
You get the following statement:
"Each game or application can be assigned to only one device on your home network"
I would think that the only way round your problem is to have each Camera running a different application or the same application with a different name.
Does the remote browser app need to know the application name or just the device name ?
If you think about how Port Forwarding needs to function you need a way whereby the remote user needs to be able to tell the Hub what Camera to talk to. -
Port forwarding to two devices with HH4
Having set up my IP camera with HH4 successfully, I've now got another one and would like to set it up as well. I gave it a unique, static IP address which my router can see fine. When I try to set up port forwarding, I get a message saying:
"The game or application you’ve selected conflicts with an application (IP Cam 1) you’ve already assigned to another device. Please remove the other application or select the same device."
I am not being given the option to select the same device.
I'm now wondering if port forwarding to two identical devices actually works in principle with HH4? Has anyone else done this?
Solved!
Go to Solution.klara wrote:
Having set up my IP camera with HH4 successfully, I've now got another one and would like to set it up as well. I gave it a unique, static IP address which my router can see fine. When I try to set up port forwarding, I get a message saying:
"The game or application you’ve selected conflicts with an application (IP Cam 1) you’ve already assigned to another device. Please remove the other application or select the same device."
I am not being given the option to select the same device.
I'm now wondering if port forwarding to two identical devices actually works in principle with HH4? Has anyone else done this?
If in the Home Hub 4 A you go to
Advanced Settings
Firewall
Port Fowarding
Manage Games and Applications
You get the following statement:
"Each game or application can be assigned to only one device on your home network"
I would think that the only way round your problem is to have each Camera running a different application or the same application with a different name.
Does the remote browser app need to know the application name or just the device name ?
If you think about how Port Forwarding needs to function you need a way whereby the remote user needs to be able to tell the Hub what Camera to talk to. -
Port forwarding for Warcraft 3 - no other posts have helped me solve this :
Hi everyone,
At risk of flogging a dead horse, I am having trouble with port forwarding/port mapping on my new AEBS and need help.
Warcraft 3 requires ports 6112-6119 open, which I had successfully set up through the Router Management Interface of my router (Speedstream 536 v6). Since I've set up the airport and run the router through it, I've been unable to host/join games on Warcraft, due to ports not being open.
I've since gone back in to the router setup and attempted to configure it. I've tried sending the open port traffic to the base station, to the computer, and a combination of each, but nothing seems to fix it.
Aside from port forwarding, it is working fine. My internet connection is flawless (a little slower than before airport ... or perhaps my imagination?), my Wii and XBOX360 both find the network fine (360 hard wired over ethernet due to wireless security issues ... see other threads!), but I can't play my warcraft games.
The help system (and some of the other threads on here) direct me to the Airport Utility -> Advanced -> Port Mapping. The problem is that on my advanced pane I only see:
- Logging and SNMP
- Bonjour
- IPv6
I've tried restarting the AEBS but get no joy. Is there something I'm doing that is fundamentally wrong? Can anyone help me? I'm not sharing the connection with any other computers, just wii and xbox, if that makes any difference.
If there's anything else you'd need to know, please ask me.
I look forward to your responses, and any help is most appreciated.
Regards,
GHThe IP address of my iMac is 10.0.0.1; the address of the Speedtouch is 10.0.0.138; the AEBS is 10.0.0.2, and the xbox360 (which the speedtouch sees as "Generic device") is 10.0.0.4.
On the speedtouch setup page, there's a lot of long-winded gibberish which I don't really understand, but perhaps it'll be of some use to someone more knowledgable on the topic. Each device has the following information:
iMac (which it lists as Unknown-00-11-24-bb-ef-96):
Information
Status: Active
Type: Generic Device
Connected To: ethport1 (Ethernet)
Addressing
Physical Address: 00:11:24:bb:ef:96
IP Address Assignment: DHCP
IP Address: 10.0.0.1
Always use the same address: No
DHCP Lease Time: 0 days, 16:34:40
Connection Sharing
Game or Service
War3
Warcraft III
(This is what I had named the settings which opened ports 6112-6119 on TCP and UDP respectively. As stated, it worked fine before the airport came along, and I've since tried removing and reinstating with no success).
Airport-Extreme
Information
Status: Active
Type: Generic Device
Connected To: ethport1 (Ethernet)
Addressing
Physical Address: 00:16:cb:c2:c3:2c
IP Address Assignment: DHCP
IP Address: 10.0.0.2
Always use the same address: No
DHCP Lease Time: 0 days, 16:38:05
Connection Sharing
There is no game or service assigned to this device.
Xbox360
Unknown-00-17-ab-4f-fa-a6
Information
Status: Active
Type: Generic Device
Connected To: ethport1 (Ethernet)
Addressing
Physical Address: 00:17:ab:4f:fa:a6
IP Address Assignment: DHCP
IP Address: 10.0.0.4
Always use the same address: No
DHCP Lease Time: 0 days, 16:31:45
Connection Sharing
There is no game or service assigned to this device.
Does any of this help at all? -
Port forwarding is not working on SRP521W
Hello,
I have a problem with incoming traffic.
I opend 3 ports as followed:
I have olso anabbled de remote web menagement on port 888.
From the outside i can access the remote management. but i cannot access my webserver on prot 80 or 443. I have checked with the isp provirder en these port or not blocked.
Can anywane help,
Thanks,Hi Danny, to my recollection there are not any bugs on the current releases for the SRP for forwarding.
To affirm, you have went to Network Setup -> NAT -> Port forwarding
Also, are you able to log in to the server locally with the LAN IP address using an internet browser for http and https?
-Tom
Please mark answered for helpful posts -
Problem with opening/port forwarding some ports but not others
I read the Faq and the first few pages of the forums but couldnt find anything.
I am using the Port Forwarding (WRT54G, Firmware 4.20.7) to my network camera to try to open up ports 80, 554, 5556 and 5558.
Using the network toolbox at Blackcode.com I then check the ports to see if they are open.
Port 554 seems to be open. Port 80, 5556 and 5558 do not appear to be open.
I am using the correct external IP address (I can toggle port 554 open and closed and test that). Toggling Blocking Anon Internet Requests Of/Off makes no difference to the result.
I have checked with my ISP and they dont claim to block those ports.
Any thoughts on what this could be? Is there a way to test if its my ISP? If it is my ISP, is there a workaround?
Thanks for any help.Are you sure the camera does listen on those port at the time you did this tests? Are those ports open inside your LAN, too?
5556 and 5558 look like RTP ports which may only be active after the channels have been established through RTSP.
Forwarding of port 80 is known to be an issue on various routers as the router allocates port 80 for the web interface. Sometimes it helps to change the remote management port on the router from 80 to 8080 or something else. You may even have to enable remote management to get this active.
If this does not work you have to reconfigure port 80 on your server to a different port if possible.
Message Edited by gv on 08-21-2007 12:28 AM -
Help needed to do port forwarding in ipfw...
For the last weeks I have been working to get the new open-source content management system Alfresco working. It is a pure Java web application that runs under Tomcat. There is official support for Mac OS X but only Windows and Linux gets true installer binaries with guides and everything.
The unique thing about this platform is that it has a built in Java-based CIFS/SMB-server to expose the content not only in web browser but as a mounted volume as well. However, it turned out more than difficult to get that working in my Mac OS X Server 10.4.9 running on an XServe G5 2.0Ghz.
I can run the startup script for the Tomcat as root on my laptop running Mac OS X 10.4.9 and then the CIFS-server can use standard ports like 137, 138, 139 and 445. Finder can mount that as a volume called Alfresco. However, I do not want to run it as root because of several other issues related to X11. There is a note in the installation text that if running the script not as root but as admin or a designated Alfresco user requires port forwarding. That means setting up firewall rules to forward requests from the standard CIFS TCP ports 139/445 to the non-privileged ports the Alfresco CIFS server is listening on (which are 1137,1138,1139 and 1145).
I have understood that this is not possible through the Server Admin GUI-app but needs to be done either in the terminal or by using an app like WaterRoof. I guess also Apple´s server tools are famous for overwriting config files made by a "third-party" app. However, I can't make it work and ipfw syntax still looks very confusing to me. Any ideas of what I need to do in order to have this port forwarding to work.
I have tried something like this so far:
# ! /bin/sh
echo "Setup CIFS Port Forwarding ..."
sysctl -w net.inet.ip.fw.enable=1
sysctl -w net.inet.ip.forwarding=1
sysctl -w net.inet.ip.fw.verbose=1
sysctl -w net.inet.ip.fw.debug=0
#ipfw add 100 count log ip from any to any
ipfw add 200 allow ip from any to any via lo0
# Forward native SMB and NetBIOS sessions to non-privileged ports
ipfw add 300 fwd 192.168.1.2,1445 tcp from any to any dst-port 445 in
ipfw add 400 fwd 192.168.1.2,1139 tcp from any to any dst-port 139 in
# Forward NetBIOS datagrams to non-privileged ports
ipfw add 500 fwd 192.168.1.2,1137 udp from any to any dst-port 137 in
ipfw add 600 fwd 192.168.1.2,1138 udp from any to any dst-port 138 in
Windows filesharing i Mac OS X Server is turned off and there are firewall rules to allow traffic on the designated ports.
http://www.alfresco.com
Any hints would be very helpful!
XServe G5 Mac OS X (10.4.9)Ok, thanks for the tip. Had a look at that page and it was only about NAT which is not what I am looking for. I have a server with public IP where I need to forward from one port to another on the same IP. However, I find the information about how to configure IPFW rather limited so I wanted to know if the rules in the first post look right and what pitfalls there are when using the GUI-based server admin tools from Apple
-
Port Forward in Cisco series 800
Dear Support
below the configuration of Cisco Series 800 Router that Has VDSL port of internet , the configuration as below :
i add three command
what is required in order to make port forward
ip nat inside source static tcp 8000 10.10.10.10 8000 dilar 0
ip nat inside source static tcp 554 10.10.10.10 554 dilar 0
ip access list extended 100
permit ip any any
what is required to make port forward to the local ip address 10.10.10.10 from outside interface that is VDSL port ?
! Last configuration change at 10:47:44 KSA Wed Apr 22 2015 by aamalsup
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime
service password-encryption
hostname AamalNet
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
enable secret level 2 5 $1$Y4PF$K6TQ5wf0gcHiO5IxvLZba0
enable secret level 5 5 $1$WZeO$BzTCl0C0e1078CWxExJK0/
enable secret 5 $1$plq6$P5HVL/tR81cs0GFDrD.0V/
aaa new-model
aaa authentication login default local
aaa authentication login sdm_vpn_xauth_ml_1 local
aaa authentication login sdm_vpn_xauth_ml_2 local
aaa authorization exec default local
aaa authorization network sdm_vpn_group_ml_1 local
aaa session-id common
clock timezone KSA 3 0
crypto pki trustpoint TP-self-signed-1682106276
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1682106276
revocation-check none
rsakeypair TP-self-signed-1682106276
crypto pki certificate chain TP-self-signed-1682106276
certificate self-signed 02
30820250 308201B9 A0030201 02020102 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31363832 31303632 3736301E 170D3032 30333031 30303038
35315A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 36383231
30363237 3630819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100C2F3 49897460 71FEB259 7794B7C6 D398958A 2D338F0F C69F0E75 1137B16C
C261A275 8416DAF6 FC19AA6E 50024019 66CE4DB8 3AFAB6FE CE892B42 86A93490
97259E47 D740B2F4 9AA2D307 7B676841 2CAAA879 D945A6FD 717B507F 77399332
1644CEDE 884BF133 ACFBBC80 9869A104 54CC3EEE 9D521378 EC762D86 C3F0ABC9
CA990203 010001A3 78307630 0F060355 1D130101 FF040530 030101FF 30230603
551D1104 1C301A82 18417761 6C416D61 6C792E61 77616C6E 65742E6E 65742E73
61301F06 03551D23 04183016 80149ADD A651C9F9 F8369354 5C904777 090FEB75
72E0301D 0603551D 0E041604 149ADDA6 51C9F9F8 3693545C 90477709 0FEB7572
E0300D06 092A8648 86F70D01 01040500 03818100 50ACCA98 1A5FCCAD FC61D703
A8589B02 AFB8CD47 BD1CC7B0 B095C97F AA0604A8 F8495053 C8A9CBB9 644F5674
318A7AA0 873250AD 1DE28CE2 BE21ED19 BF212CF7 E2A97CFB FFA62F1E 643CEDFE
90D02109 719FD4D3 98E6C40B D61CE89C D2426C1E 3CBD9FBE 397F7F7C F1DD279E
14F8BB2D ABFA784B 6E04274B EDCBFC8F A805E91D
quit
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address 10.10.11.1
ip dhcp pool lan
import all
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 212.93.192.4 212.93.192.5
lease 0 2
ip dhcp pool wireless
import all
network 10.10.11.0 255.255.255.0
default-router 10.10.11.1
dns-server 212.93.192.4 212.93.192.5
lease 0 2
no ip domain lookup
ip domain name aamal.net.sa
ip name-server 212.93.192.4
ip name-server 212.93.192.5
no ipv6 cef
cwmp agent
enable download
enable
session retry limit 10
management server password 7 094D4308151612001D05072F
management server url http://aamalservice.aamal.net.sa:9090
license udi pid C887VA-W-E-K9 sn FCZ17459018
archive
log config
hidekeys
username k privilege 15 password 7 020D
username admin privilege 15 password 7 14161606050A
controller VDSL 0
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group aamalnet
key aamalnet
dns 212.93.192.4 212.93.192.5
include-local-lan
dhcp server 10.10.10.1
max-users 10
netmask 255.255.255.0
crypto isakmp profile sdm-ike-profile-1
match identity group aamalnet
client authentication list sdm_vpn_xauth_ml_2
isakmp authorization list sdm_vpn_group_ml_1
client configuration address respond
virtual-template 1
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
mode tunnel
crypto ipsec profile SDM_Profile1
set security-association idle-time 60
set transform-set ESP-3DES-SHA
set isakmp-profile sdm-ike-profile-1
bridge irb
interface ATM0
no ip address
no atm ilmi-keepalive
interface ATM0.1 point-to-point
pvc 0/35
pppoe-client dial-pool-number 1
interface Ethernet0
no ip address
shutdown
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface Virtual-Template1 type tunnel
ip unnumbered Dialer0
tunnel mode ipsec ipv4
tunnel protection ipsec profile SDM_Profile1
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
no ip address
interface wlan-ap0
description Embedded Service module interface to manage the embedded AP
ip unnumbered Vlan1
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface Vlan2
no ip address
bridge-group 2
interface Dialer0
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap callin
ppp chap hostname [email protected]
ppp chap password 7 0007145E2E5A05522E1858
no cdp enable
interface BVI2
ip address 10.10.11.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 1 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.255
access-list 1 permit 10.10.11.0 0.0.0.255
access-list 23 permit 212.93.196.0 0.0.0.255
access-list 23 permit 212.93.192.0 0.0.0.255
access-list 23 permit 212.93.193.0 0.0.0.255
access-list 23 permit 10.10.10.0 0.0.0.255
access-list 23 permit 10.10.11.0 0.0.0.255
dialer-list 1 protocol ip permit
no cdp run
snmp-server community private RW
snmp-server community public RO
bridge 1 protocol ieee
bridge 1 route ip
bridge 2 protocol ieee
bridge 2 route ip
privilege interface level 5 encapsulation
privilege interface level 5 description
privilege interface level 5 no encapsulation
privilege interface level 5 no description
privilege interface level 5 no
privilege configure level 5 ip route
privilege configure level 5 interface
privilege configure level 5 controller
privilege configure level 5 ip
privilege exec level 5 copy running-config tftp
privilege exec level 5 copy running-config
privilege exec level 5 copy
privilege exec level 5 write memory
privilege exec level 5 write
privilege exec level 5 configure terminal
privilege exec level 5 configure
privilege exec level 5 show processes cpu
privilege exec level 5 show processes
privilege exec level 2 show running-config
privilege exec level 5 show configuration
privilege exec level 2 show
privilege exec level 5 clear counters
privilege exec level 5 clear
banner exec
CC
% Password expiration warning.
Cisco Router and Security Device Manager (SDM) is installed on this device and
it provides the default username "cisco" for one-time use. If you have already
used the username "cisco" to login to the router and your IOS image supports the
"one-time" user option, then this username has already expired. You will not be
able to login to the router with this username after you exit this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you want to
use.
banner login
CC
********STC AamalNet Service****************************************
********Authorize Access Only. For more Support Call 909************
line con 0
privilege level 15
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
stopbits 1
line vty 0 4
access-class 23 in
privilege level 2
transport input telnet ssh
scheduler max-task-time 5000
scheduler allocate 20000 1000
endHello,
Sure.
What version are you running?
Regards, -
Linksys WRT610N Port Forwarding
I am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via www.grc.com. The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
Is there a bug? Can technical support please help?
Some background: I'm in the UK and I connect to the internet using the Fibre-to-the-cabinet (FTTC) technology. I have a BT supplied modem (Huawei Echolife HG612) which is completely locked (it is BT property) with no ability to log in and change settings. The WRT610N is plugged into the LAN socket of the modem and connects via PPPoE. Everything else works fine.A firewall does not open or close a port. A firewall blocks or passes transient traffic. Thus if the port is closed on the computer it doesn't matter what the firewall does. The port will never show up as open as long as the port is not in use.
ifconfig
netstat -an -
BT Home Hub Port Forwarding, Device Not Listed
Hi Guys,
It's quite a simple one really but it has me totally stumped. I've been trying to open a couple of ports recently, for games etc and I know how all this port forwarding stuff works, but recently I had hard drive issues and had to re-install windows etc, all the usual **bleep**. Since then though, when trying to forward a port in the hub manager (I have BT Home Hub 2), my device doesn't appear in the drop down list, neither the physical hexadecimal address nor the name I assigned to the machine! My Xbox, Iphone and my dads laptops are all on the list... just not the machine I'm using right now, even though its wired up by ethernet cable and I'm using the hub for the internet to get onto this website right now! -.-
Any help is appreciated!Anonymoose wrote:
Hi Guys,
It's quite a simple one really but it has me totally stumped. I've been trying to open a couple of ports recently, for games etc and I know how all this port forwarding stuff works, but recently I had hard drive issues and had to re-install windows etc, all the usual **bleep**. Since then though, when trying to forward a port in the hub manager (I have BT Home Hub 2), my device doesn't appear in the drop down list, neither the physical hexadecimal address nor the name I assigned to the machine! My Xbox, Iphone and my dads laptops are all on the list... just not the machine I'm using right now, even though its wired up by ethernet cable and I'm using the hub for the internet to get onto this website right now! -.-
Any help is appreciated!
Hi Anonymoose and welcome
Try power cycling the hub (turn it off and on) with your device connected and see if it then appears on the list.
-+-No longer a forum member-+-
Maybe you are looking for
-
Datatabase permissions configuration
Hi My form is designed with designer 8 and I have put all the necessary Reader Extensions to ACCESS THE DATABASE dynamically when the button is pressed (passing one of the form fields as a parameter to the database select statement) and everything SE
-
I just created a website on iWeb, but the site name is not showing up on the internet page tab. So if, for example, I have Google and my site open, the tabs are "Google" and mine is blank. Advice? Thanks!
-
Greetings I have been using avelsieve successfully for message filtering & forwarding, accessing GUI via squirrelmail on my OS X Server (10.4.8) But when I tried to log in to alter a filter today, I was unable to get to the message filters screen (ca
-
Need JavaHelp Solaris package to go with JDK 1.5 installation
[Sorry - I had posted this in another forum before finding this forum... Hope someone here can help... Thanks!] Hi, I've installed the JRE component of JDK 1.5.0_20 on a Solaris 9 SPARC system, but it looks like that broke SMC. I think I found a so
-
Help with mic problems please!
Currently I have a Sound Blaster Audigy2 ZS sound card with I-Trigue L3500 speakers. I have had this system for a bit now and have never needed to use a mic till recently. The system has a wired volume/bass control that plugs directly into the sub. I