EA6900 PPPOE problems with D-link DSL-320b

Hi
I really hope someone can help as I can't seem to find a working answer in the forum yet.
I have a new D-Link DSL-320B modem/router. This works fine as a modem/router, however as I also now have a Linksys EA6900 router I wanted to stop the router part of the D-link so it would just be a modem. I assume this would be a good thing to do, but don't really know why.
I followed instructions to configure the D-Link modem/router as a bridge:
I set the Manual ASDL Connection Setup in Bridge mode '1483 Bridged IP LLC' (note I also tried in the 'Bridged IP VC-Mux' option at a later point), VPI 0 and VCI 38 (as per my ISP instructions), saved the settings and then under the LAN tab I disabled the DHCP Server, saved the settings and lost internet connection (which I expected).
I then attached the D-Link into the WAN port of the EA6900, the computer via ethernet to one of the 4 ethernet ports on the EA6900 and manually set up the EA6900.
Under 'Connectivity'-'Internet Settings' I set up the ipv4 to:
Connection Type: PPPoE
Username/Password (as provided by my ISP which had previously worked in the D-Link standalone)
Service name (left blank)
Connection mode: Keep Alive, redial 30 secs
On the right hand side of the page, I set the MTU to manual and size to 1432 (again as per my ISP instructions on setting up routers).
However, after pressing applying, whilst the device is connected to the router, the router is not connected to the internet.
Am I missing something? Should I just leave my DSL D-Link with the ADSL connection and DHCP server enabled and put the EA6900 into Connection Type: automatic configuration -DHCP? as this does give me internet access.
Please help.
Many thanks in advance
Hannah

To isolate the issue I recommend connecting a computer directly to the modem. The create PPPoe connection to test whether or not the Modem is actually bridging as per your ISP instructions. Once you verify that the modem is bridging with your computer transfer those settings to the EA6900. Don't change the MTU from Auto initially. Only change the MTU if you notice you can get to some site and not others. That's typically a sign that there is an MTU issue. Actually for PPPoe the MTU is typically 1492.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Similar Messages

Problems with Dinamic Link between Premiere pro CC and After Effects CC

I'm having serious problems with dinamic link between premiere pro and after effects, really serious problems that have 2 big projects in trouble (a documentary and a video clip) and I had to redo all the work pipeline to the consumer.
The documentary for a spanish TV was made on CC 2014 and a video clip was made on CC. Both of them with a lot of after effects composition in the premiere pro timeline. Render freeze, a lot of playback issues, and many more problems... Until I decided to remove these links between premiere and after effects and render out all the after effects compositions one by one and insert as clips in premiere pro. 1 week working away with back and fourth.
I've got a huge workstation:
i7 4990
32Gb ram
GTX780 3gb
256 gb system ssd
2 Tb project storage
*All my hardware and software are update.
I know that a lot of folks are on the same huge problem and I want to ask everyone:
How do you save this?
What is your pipeline?
Are there any solution?
Best practice to use dinamic link in a huge project?
Thanks,
Ruben Gimenez.
R&D iceblink.es
www.rambot.es

Thank You, Jim -
Unfortunately that specifically did not work.
Based on another comment sent to me, here is what did.
In PProCC
File > Adobe Dynamic Link > New After Effects Composition
In AECC
From that composition created from PPro, I imported the project (aep) initially created in AECC from another team member. Saved the file.
Back in PProCC
File > Adobe Dynamic Link > Import After Effects Composition
Magic.

Hi guys. i have some problem with a link from a pdf on-line,when i click on it,the page adds a "%" at the and of the link and says "page not found" because of it

Hi guys. i have some problem with a link from a pdf on-line,when i click on it,the page adds a "%" at the and of the link and says "page not found" because of it.
This happens only when a load my pdf file on my server, because if i click on the link when the file is on my iPad, the page opens without problem.
Any help please?
thanx

the % sign is often used when there's a space in a name. HTML doesn't like spaces so it fills them with % or %20
try, on the end of that link, see if there's a space built into the page or the link when the page was made
On the web address you may be able to 'backspace' at the end and erase that space to get the address, but whomever made the page possibly put a mistake in the link

Problem with Help Link in search result screen of PCUI

Hi,
I am trying to access the pcui applications that came out of box with crm using BAB,everthing is working fine but got a problem with "Help" link in top right (beside personalize link) the search result area of all the PCUI screens.
when i click on that i get "page cannot be displayed" error, seems that it is pointing to some wrong URL, where should i change the url to point to our company's help site for that link..
clicking on the properties of that link shows that it is pointing to
javascript:CATshowF1(%20'/sap/bc/bsp/sap/crm_bsp_f1_help/f1help.do?doctype=kw&loio=70B4ED8E03595645A6ABA33B4576BB57&class=IWB_EXTHLP&language=E' );
Please help me in this regard.
Thank you

My response help resolve Kodru's Message which he also posted in EP Implementation Forum. He resolved it by changing the variant noted below.
The link http://help.sap.com/saphelp_crm40/helpdata/EN/70/B4ED8E03595645A6ABA33B4576BB57/content.htm should display Activity Info.
First I would check if the crm_bsp_f1_help service has been activated in SICF.
Secondly I would check the settings in the IMG -> SAP WAS -> Know. Mgt. -> Settings in App. Sys. -> Usage of Help Type "Dynamic Help". The Tab PlainHtmlHttp should have a variant called CRM_HELP, Server Name (help.sap.com) and path.

After Effects won't close/Problems with dynamic links

When I quit After Effects the icon still shows up and it says that it is still open, even force quit will not work. Also having problems with dynamically linked files between after effects and Premiere pro. Rendering in Premiere doesn't work unless I go to AE, save the project, then go back to Premiere. I have OSX Mavericks 10.9.2, a late 2012 mac pro, and AE CC 12.2.1.5

Kevin: would appreciate further thoughts on this.
I am using Pr2014, version 8.0.0 I am using AE2014, version 13.0.2.3. When I was on earlier versions of each, I had no problem importing AE comps into Pr. I'd choose import in Pr, then select the AE project, then select the comp. But with my new and improved versions of AE and Pr, I keep getting "importer reported a generic error."
I also tried to go the other way. I selected in Pr the clips I wanted to work on in AE, and then tried "replace with AE comp" but got the "generic error" message again..
Finally, I attempted to create a Dynamic Link from Pr via the File menu, but with each of the options from there, I got "failed to connect to AE Dynamic Link"
Any advice you can share, would be most welcome.

Strange problem with Database LInk

Hi Everyone,
I have strange problem with Database Link in Oracle 11g Express Edition;
There are two computers: computer-server and computer-client. Tnsnames.ora are the same on both computers ie.
CT =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = krzysztof)(PORT = 1521))
(CONNECT_DATA = (SERVICE_NAME = XE)
I created database link :
Create database link zdalny
Connect to <user_id> identified by <password>
using ‘CT’;
Client can’t connect with server when I am using above command. But when I change “using” for using ‘krzysztof:1521’ or using ‘krzysztof’ or using ‘server IP:1521’ – everything is ok.
Why I am asking. Because in all materials which I am reading about Oracle command with using ‘CT’ should be working correct. But there is not. Do you know, why?
Thanks in advance and apologize for my English.
Rgds
Krzysztof

Krzysztof Szymaniak wrote:
Thanks for all replies.
Below is server's tnsnames.ora
CT =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = krzysztof)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = XE)
EXTPROC_CONNECTION_DATA =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(CONNECT_DATA =
(SID = PLSExtProc)
(PRESENTATION = RO)
ORACLR_CONNECTION_DATA =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(CONNECT_DATA =
(SID = CLRExtProc)
(PRESENTATION = RO)
SQL Error: ORA-12154: TNS:could not resolve the connect identifier specified
12154. 00000 - "TNS:could not resolve the connect identifier specifie
Rgds
Krzysztof
PS. I tried with using 'XE' - not working.Assuming that is the correct tnsnames, of course XE is not working. You don't have a tnsnames entry for 'XE'.
You need to be aware that when using a dblink, the client is the db in which the link is defined, not the desktop from which you connect to that database.
I think you need to start here:
http://edstevensdba.wordpress.com/2011/02/26/ora-12154tns-03505/
http://edstevensdba.wordpress.com/2011/02/09/sqlnet_overview/ (Help! I can’t connect to my database )
http://edstevensdba.wordpress.com/2011/02/16/sqlnet_client_cfg/ (Help! I can’t connect to my database (part duex) )
The fact that your client (db link) is a database doesn't change anything taught in the above.

Problems with graphics [link removed]

Hi everyone.
I have problems with graphics [link removed] - Ogłoszenia Hrubieszów. Darmowe ogłoszenia Hrubieszów i okolice. If you want to help, please [link removed] help me in diagnosis. THX !

Explain what exactly the problem is rather than spamming the forum with links. The page looks just fine in Firefox and Chrome.
Mylenium

Macbook Pro Problems with D-Link Router

My router D-link (Dl-624+A, model available in Asia) 802.11g/2.4 Ghz wireless router serves a G5 iMac, a G4 Aluminum Powerbook plus a Windows laptop and desktop. We have never experienced any problems with the network.
I have recently bought a 17" Macbook Pro 2.4 Ghz laptop (intel MBP) and have not been able, in any combination of modes, to join the network. A dialogue box simply says that there was an error trying to join the network.
I have no problems joining other wireless networks around town its so easy, just the one at home is the problem.
What is going on? Is there a fix? Thanks

Hi, my MacBook Pro can't connect to my D-Link DSL-G604T router via wireless too.
Airport can see my wireless connection and asks for the WEP password to connect. I put the password key in and an error pops up saying it cannot connect. I can connect via an Ethernet cable. Also, my previous system PowerBook G4 is able to connect via to the router via wireless, hence there is nothing wrong with my network.
Based on the suggestions from other threads, I tried to set my security to WPA instead of WEP. However, after I set my security to WPA, and tried to connect to my wireless network, the AirPort popup only gives me 4 options for the Wireless Security:
WEP Password
WEP 40/128-bit hex
WEP 40/128-bit ASCII
LEAP
There isn't an option to use WPA. Can anyone advise?

IChat video conferencing problems with D-Link WBR-1310

Howdy,
I am having a few problems with iChat video conferencing. I use the D-Link WBR-1310 wireless router and a MacBook. My girlfriend has a MacBook Pro at her school which she connects to via ethernet. I connect to my router via wireless. The routher is connected to a DSL modem. iChat video conferencing tends to work sometimes but very rarely. I have DMZ on the router turned on as i read somewhere on these forums that it was recommended. I also have the Apple firewall turned off so my laptop is pretty much naked as far as security is concerned. Three other computers use the network One desktop PC connected directly into the router and two Apple iBooks which are connected via the wireless. The problem is that i keep getting error message -8. Can anyone please help?
Thanks in Advance

I'd start by verifying you have the most recent firmware installed on your router.
Next, start off by trying to test to a user that has no known issues: http://www.ralphjohnsuk.dsl.pipex.com/ContactTesters.html (Bottom of the page)
That will help pinpoint where the connection issue lies.
Once you can succefully connected, then you should set up a static ip address on your mac and port forward the necessary ports in your router. If you router supports UPnP, I'd try enabling the first.
I hope this helps!

Problem with action links

I have a relatively simple DVD project with 10 movie sequences each placed on a separate timeline. DVD has just one menu with a Button: "Watch whole movie" which basically sequences all 10 clips and then back to the menu.
Then I also have 10 Sequence-Buttons on the menu that should only show the respective sequence and then back to the menu.
1. I set up the action sequence for "Watch the whole movie" m1-m2-m3-m4-m5-m6-m7-m8-m9-m10-menu. No problem with that.
2. When I then start working on the first sequence button "SCENE 1" the problem starts. What I want is just Scene1-back to the menu. I tried it without and with end action override but then I disturbed the m1-m2-m3-m4-m5-m6-m7-m8-m9-m10-menu sequence.
I really couldn't figure out this simple task. Maybe somebody can give me a hint.

1. I set up the action sequence for "Watch the whole movie" m1-m2-m3-m4-m5-m6-m7-m8-m9-m10-menu. No problem with that.
Actually, that is the problem. Instead of making the end action of each timeline the next timeline, create a Playlist and sequence the timelines in there. Your play all button links to the playlist. End action of the playlist is Return to last menu.
Without end actions that go to the next movie, your Scene buttons will work fine. (The end action on each timeline will be "Return to Last Menu."

Problem with subrpt links in crystal reports 8.5 (cr 9 and 2008 installed)

I am trying to add a subreport to an existing CR 8.5 report. I currently have Cr 8.5, cr 9 and cr 2008 on my pc (xp). The subrpt is pointing to a sql 2005 stored procedure that has a parameter (@vvcrCono). When I try to set up the link, the parameter is not listed in the of available parameters to link to. I select a field from the available fields on the main report, hit the > to move it over as a field to link to, and the dropdown that contains the list of parms to link to on the subreport will change to ?pm-(fieldname). I do not see the parm list from the subreport. I am unable to get the link defined. This occurs even when trying to edit an existing subreport.
Is there a problem with running these crystal report versions on the same machine? Or am I just missing something? It has been a while since I've used cr 8.5.

Joanne, thank you for your posted solution and specifically your mention of miniscule scroll bar of the 'subreport parameter field to use' drop down, I had been on several forums but none of them mentioned this, my subreport now accepts the passed parameter and main report works well. Hope your post helps others as it did me, only wish we could include a graphic to illustrate this as I have seen same question posed several times and several different msg boards.

Problem with PDF, link in website doesn't find the adobe

We are using Windows XP, Internet Explorer 8 and Adobe Reader 9.0.
There is a website with a link to open the dokument with adobe. But when we take a klick on this link adobe isn't found. The format of the file is any file and there only cryptical sign in the file, which would be open. Please - I need help!

I have the same problem - shocked that this hasn't been addressed by Adobe or Microsoft. It began with recent updates. Adobe Reader will not open a .pdf file on the web. I sometimes get the following dialog but mostly I get a blank screen with "Done" in the status bar.
If I open a .pdf from my hard drive I get a message about protected mode. If I click on the link in the message, I get Adobe instructions about turning off protected mode - but it is already turned off. If i cancel that message i can open a local .pdf.

Two problems with my linked text

Hi, I am having a couple of problems with my code for a link.
Problem 1
I am trying to get the text "learn more" to be "red" on (main) but it is only showing "red" on (over) or hover. Please tell me how to make the text "red" on (main).
Problem 2
The code seems to be identical for all thumbnails but only the text below the "circled" image seems somewhat correct. I can't figure out why the other text has a link (is linked) when the code is the same as the "circled" code.
http://www3.telus.net/~jessum/holiday pools/index.html

<a href="http://www3.telus.net/~jessum/holiday pools/services.html" target="_self">
Thanks Nancy, so I named my main website folder "holiday pools", (with a "space") I guess this is bad. So in my code (see above) there is a space in "holiday pools".
Question #1
Do you know how can I delete the space or add a underscore without destroying all of my linked pages and images?
Question #2
I read that this (see below) is how I can add comments without it being visible in the browser, so why is this giving me errors?

IP / DHCP Problems with D-Link Extreme

I have been having a lot of problems with my current set up.. D-Link router/modem -> Airport Extreme >WDS> Express. The D-Link router has the "DHCP Range" of Start: 192.168.1.2 End: 192.168.254 and Lease time of 24 hours. The Airport extreme has the IP Address of 169.254.255.1 and Connection Sharing set to Off (Bridge Mode). The Airport Extreme keeps telling me it does not have a valid IP address and my MBP is connected to the AEBS is saying Airport has a self-assigned IP address and may not be able to connect to the internet. I have no idea of what settings to change it to. Help please.

Most likely there is a bad connection between the D-Link router and the Base Station, accounting for the inability of the Base Station to communicate with the D-Link router and thus obtaining an IP address.
Does the status light on the D-Link router port to which the Airport Base Station is cabled show a valid and active connection? If not, try a different ethernet cable for connecting the two devices and/or try plugging the Base Station into a different port on the D-Link router.

WRT110-EU with D-Link DSL-320T

Hi, I have just bought a Linksys WRT110-EU router, to work with my D-Link DSL-320T ADSL modem. The computer works well with the DSL-320T, but I do not seem to be able to configure the WRT100 to work with it. I am using the EasyLink tool, and I cannot get it past the step of setting up the WAN interface. I guess I am missing something, probably in the configuration of the DSL-320T, but I cannot figure out what to do. The output from ipconfig /all, on current connection (DSL-320T modem only) is below: Windows IP Configuration Host Name . . . . . . . . . . . . : pcbport1 Primary Dns Suffix . . . . . . . : ualg.pt Node Type . . . . . . . . . . . . : Broadcast IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : ualg.pt Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek RTL8139/810x Family Fast Ethernet NIC Physical Address. . . . . . . . . : 00-1B-38-AC-48-DB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 151.32.20.144 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 193.70.152.15 Lease Obtained. . . . . . . . . . : terça-feira, 7 de Outubro de 2008 00:55:05 Lease Expires . . . . . . . . . . : terça-feira, 7 de Outubro de 2008 00:56:05 Any help will be appreciated

Check these two settings on your computer (1) If your computer has a static ip on it .Click on the Start button >>> Settings >>> Control Panel >>>Network
Connections- Right click on th icon for Local area connection and go to
properties- On the 'General' tab select 'Internet Protocol TCP/IP' and click on the Properties button- Check if it is set to Obtiain and IP . (2) On network connections check if have any other ICON than Lacal area connection Lan or high speed internet. and wireless network connection or 1394 connections disable it. Then try the CD set up.

EA6900 PPPOE problems with D-link DSL-320b

Similar Messages

Maybe you are looking for