EAP and AES CCM on 1310 AP/Bridges
I have a pair of Cisco 1310 AP/Bridges. I am attempting to use them only in bridge mode. I can get them configured using open/wep/wpa shared keys, but when I attempt to configure them using AES CCM and Network EAP I can not get them to talk to each other. The Root Bridge which is setup as the Radius with a dedicated user for the Non-Root gives the error of "NAS shared key mismatch with XX.XX.XX.XX" and the Non-Root Bridge gives the error Interface Dot11Radio0, cannot associate EAP authenticating" I have checked the Radius shared key on the Root and also ensured that the username and password on the non-root match. I can't find much on this on the interwebz. Any help will be greatly appreciated.
Ben,
can you post the configs of the root and non-root bridges?
the key mismatch error means the key you entered in the local-radius config, and the ip radius-server lines do not match. When you enter these you want to use 'key 0' not 'key 7'. the AP will encrypt the key after you enter it.
Steve
Similar Messages
-
Enable AES encryption on 1310 Wireless bridge
Hi All,
I have requirment to enable the AES encryption on the management VLAN traffic between connected root and non root bridges . can any one share the configuration guidelines please ??
below is the network setup .
Router<---->SW1 ( main office)--> Root-bridge < ---------->non root-bride------SW2 ( remote end site)
Apart from the specific configuration on the wireless bridge is any extra configuration required on the Switch interfaces??
Regards
LernerHello,
1. Make sure you are running version 12.3(7)JA or later since WPA2/AES was not always available for the 1310.
2. How do you currently have the root/non-root configured?
Ideally, adding AES shoudl be fairly straight forward. Keep in mind we recommend using WPA2 with AES.
configured on your root AND non-root:
dot11 ssid
authentication open
authentication key-management wpa version 2
interface do1
encryption mode ciphers aes-ccm -
Aironet 1310 using Peap Auth and AES encryption??
I have 2 1310 wireless briges in a point to point configuration with the root bridge acting as my ACS server..
I am currently running Leap Authentication and with Wep encryption but would like to upgrade this to use Peap and AES if possible??
I'm wondering if anyone has upgraded their solution to this type of encryption?
thanksWhat IOS version are you running ? 12.4(25d)JA is the last supported IOS version for this product. So you should go with that image.
If you are using AP as AAA server, then I think only EAP-FAST, LEAP & MAC authentication is supported. Not anything else.
Here is WGB (workgroup bridge) configuration with EAP-FAST & you can get an idea how to configure EAP-FAST if you choose to. (In your case you have to configure root bridge & non-root bridge in two respective AP)
http://mrncciew.com/2013/04/28/wgb-with-eap-fast/
HTH
Rasika
**** Pls rate all useful responses **** -
Hi *,
I have the following problem with RADIUS and EAP authentication.
Radius server sends an "Access-Accept" packet to my AP, but the station does not authenticate.
I've tried with different encryption configuration and with different authentication methods under "dot11 essid", but nothing changes...
What could it be?
Debug piece and configuration follows:
*Jan 25 14:23:34.795: RADIUS/ENCODE(00000012): acct_session_id: 17*Jan 25 14:23:34.795: RADIUS(00000012): sending*Jan 25 14:23:34.799: RADIUS: 4E 47 56 7A 78 65 4A 4F 55 31 47 40 77 6C 61 6E [NGVzxeJOU1G@wlan]*Jan 25 14:23:34.799: RADIUS: 2E 6D 6E 63 30 30 31 2E 6D 63 63 30 30 31 2E 33 [.mnc001.mcc001.3]*Jan 25 14:23:34.799: RADIUS: 67 70 70 6E 65 74 77 6F 72 6B 2E 6F 72 67 [gppnetwork.org]*Jan 25 14:23:34.799: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]*Jan 25 14:23:34.799: RADIUS: NAS-Port [5] 6 265 *Jan 25 14:23:34.799: RADIUS: NAS-Port-Id [87] 5 "265"*Jan 25 14:23:34.799: RADIUS: NAS-IP-Address [4] 6 192.168.173.2 *Jan 25 14:23:34.811: RADIUS/DECODE: EAP-Message fragments, 20, total 20 bytes*Jan 25 14:23:34.831: RADIUS/ENCODE(00000012):Orig. component type = DOT11*Jan 25 14:23:34.831: RADIUS: AAA Unsupported Attr: ssid [265] 8 *Jan 25 14:23:34.831: RADIUS: 57 69 66 69 45 41 [WifiEA]*Jan 25 14:23:34.831: RADIUS: AAA Unsupported Attr: interface [157] 3 *Jan 25 14:23:34.831: RADIUS: 32 [2]*Jan 25 14:23:34.831: RADIUS(00000012): Config NAS IP: 192.168.173.2*Jan 25 14:23:34.831: RADIUS/ENCODE(00000012): acct_session_id: 17*Jan 25 14:23:34.835: RADIUS(00000012): sending*Jan 25 14:23:34.835: RADIUS: 10 01 00 01 07 05 00 00 D9 37 C3 D9 79 3E 33 EA [?????????7??y>3?]*Jan 25 14:23:34.835: RADIUS: F3 7D 73 43 BF BA D0 6A [?}sC???j]*Jan 25 14:23:34.835: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]*Jan 25 14:23:34.835: RADIUS: NAS-Port [5] 6 265 *Jan 25 14:23:34.835: RADIUS: NAS-Port-Id [87] 5 "265"*Jan 25 14:23:34.835: RADIUS: NAS-IP-Address [4] 6 192.168.173.2 *Jan 25 14:23:35.035: RADIUS: Received from id 1645/64 192.168.177.158:1812, Access-Challenge, len 304*Jan 25 14:23:35.039: RADIUS: 46 10 78 5F 5F B0 CB 6C 0B 05 00 00 DA C3 BF 28 [F?x__??l???????(]*Jan 25 14:23:35.039: RADIUS: E0 18 2B 95 97 C2 0A D7 40 53 FE 62 [??+?????@S?b]*Jan 25 14:23:35.039: RADIUS(00000012): Received from id 1645/64*Jan 25 14:23:35.039: RADIUS/DECODE: EAP-Message fragments, 60+220, total 280 bytes*Jan 25 14:23:35.355: RADIUS/ENCODE(00000012):Orig. component type = DOT11*Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr: ssid [265] 8 *Jan 25 14:23:35.355: RADIUS: 57 69 66 69 45 41 [WifiEA]*Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr: interface [157] 3 *Jan 25 14:23:35.359: RADIUS: 92 DA 5E 26 CF 40 01 22 7A 8E F5 C1 [??^&?@?"z???]*Jan 25 14:23:35.359: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]*Jan 25 14:23:35.359: RADIUS: NAS-Port [5] 6 265 *Jan 25 14:23:35.359: RADIUS: NAS-Port-Id [87] 5 "265"*Jan 25 14:23:35.359: RADIUS: NAS-IP-Address [4] 6 192.168.173.2 *Jan 25 14:23:35.367: RADIUS: Received from id 1645/65 192.168.177.158:1812, Access-Accept, len 30*Jan 25 14:23:35.367: RADIUS: authenticator 8C 2C 1B 97 82 BB 6C 7F - AA D3 4A AB CA 22 8B B7*Jan 25 14:23:35.367: RADIUS: EAP-Message [79] 10 *Jan 25 14:23:35.367: RADIUS: 03 01 00 04 00 00 00 00 [????????]*Jan 25 14:23:35.371: RADIUS(00000012): Received from id 1645/65*Jan 25 14:23:35.371: RADIUS/DECODE: EAP-Message fragments, 8, total 8 bytes*Jan 25 14:23:35.671: %DOT11-7-AUTH_FAILED: Station d023.dbb8.d6a9 Authentication failed
Config:
aaa new-model!aaa group server radius rad_eap server-private 192.168.177.158 auth-port 1812 acct-port 1813 key 7 044803071D2448!aaa authentication login eap_methods group rad_eapaaa authorization exec default if-authenticated aaa authorization network default if-authenticated ! aaa session-id commonip name-server 192.168.177.45! dot11 ssid WifiEAP1 vlan 10 authentication open eap eap_methods authentication shared eap eap_methods authentication key-management wpa optional guest-mode! bridge irb! interface Dot11Radio0 no ip address no ip route-cache ! encryption vlan 10 mode ciphers aes-ccm tkip wep128 ! broadcast-key vlan 10 change 300 ! ssid WifiEAP1 ! antenna gain 0 station-role root! interface Dot11Radio0.10 encapsulation dot1Q 10 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled! interface GigabitEthernet0 ip address 192.168.173.3 255.255.255.0 no ip route-cache! interface GigabitEthernet0.1 encapsulation dot1Q 10 native no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled! interface BVI1 ip address 192.168.173.2 255.255.255.0 no ip route-cache!ip radius source-interface BVI1 bridge 1 route ip
thanks so much!Stefano: not sure if related but there is an unsupported attribute in the debugs:
Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr:
*Jan 25 14:23:35.355: RADIUS: 57 69 66 69 45 41
*Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr: interface
Try to eliminate any configured attributes on radius except those in IETF radius. Then try again.
You may also chech by removing the shared eap as suggested above. Let us know if this works.
Sent from Cisco Technical Support iPad App -
Hi,
I have another problem - after upgrade ios wirelles connection not work.
After reload i have :
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
STP: Unable to get the port parameters.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
SETUP: new interface NVI0 placed in "shutdown" state
my old configuration work propertly in the old software, but after update i have notificatio.
Old thread:
https://supportforums.cisco.com/discussion/12379491/cisco-877w-no-wireless-connection
my current sh run:
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
service password-encryption
hostname cisco
boot-start-marker
boot system flash:c870-advipservicesk9-mz.124-24.T6.bin
boot-end-marker
logging message-counter syslog
logging buffered 4096 informational
enable secret 5 $1$eCNp$rWuBfZ/cexnwnkm7L447s.
aaa new-model
aaa session-id common
dot11 syslog
dot11 ssid ciscowifi
vlan 1
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 050D031D26595D0617
dot11 wpa handshake timeout 500
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.56.1
ip dhcp pool CLIENT
import all
network 192.168.56.0 255.255.255.0
default-router 192.168.56.1
dns-server 8.8.8.8 194.204.159.1 194.204.152.34
lease 0 2
ip cef
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
username marek password 7 00121A0908500A
archive
log config
hidekeys
ip tcp path-mtu-discovery
bridge irb
interface ATM0
description Polaczenie ADSL do ISP$ES_WAN$
no ip address
no atm ilmi-keepalive
pvc 0/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
hold-queue 224 in
interface FastEthernet0
description Edzia
interface FastEthernet1
description dom
interface FastEthernet2
description Dziadek
interface FastEthernet3
interface Dot11Radio0
no ip address
no ip redirects
ip local-proxy-arp
ip nat inside
ip virtual-reassembly
no dot11 extension aironet
encryption vlan 1 mode ciphers tkip
encryption mode ciphers aes-ccm tkip
broadcast-key change 3600
ssid ciscowifi
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
world-mode dot11d country AU indoor
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1
description ciscowifi
encapsulation dot1Q 1 native
no cdp enable
interface Vlan1
no ip address
bridge-group 1
interface Dialer0
description Interfejs dzwoniacy
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp chap hostname [email protected]
ppp chap password 7 xxxxxxxxxxxxxxxxxxxxxx
interface BVI1
description Polaczenie dla sieci LAN
ip address 192.168.56.1 255.255.255.0
ip nat inside
ip virtual-reassembly
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
no ip http secure-server
ip nat inside source list 100 interface Dialer0 overload
ip nat inside source static tcp 192.168.56.10 80 interface Dialer0 80
ip nat inside source static tcp 192.168.56.10 22 interface Dialer0 22
logging trap debugging
logging 192.168.56.10
access-list 100 permit ip 192.168.56.0 0.0.0.255 any
access-list 100 deny ip any any
no cdp run
snmp-server community ciskacz RO
snmp-server chassis-id ciskacz
control-plane
bridge 1 protocol ieee
bridge 1 route ip
line con 0
no modem enable
line aux 0
line vty 0 4
exec-timeout 0 0
transport preferred ssh
transport input ssh
scheduler max-task-time 5000
end
please help - thanks!Hello Marek,
I suppose you are not planning to do any kinds of advanced config using several VLANs and multiple SSIDs so let's just make your configuration simple and working.
In short, you need to remove all references to VLAN 1 and to any subinterfaces possibly related to the VLAN 1. This means in particular (follow these steps in sequence):
Remove the Dot11Radio0.1 subinterface entirely
In the Dot11Radio0 section, remove the encryption vlan 1 mode ciphers tkip command
In the dot11 ssid ciscowifi section, remove the vlan 1 command
After performing these steps, make sure that the ssid ciscowifi and encryption mode commands are still present in the Dot11Radio0 configuration, and if not, reenter them.
Best regards,
Peter -
1310 Wireless Bridge Poor performance
Hello I am getting really bad performance on a bridge i am trying to get up,
Laptop - Switch - AIR-BR1310G-E-K9-R attena-ed ----------------
attena-ed AIR-BR1310G-E-K9-R switch laptop.
When doing an FTP Transfer i get a poor 1MB, these are currently in a lab enviroment, this is a far cry from what i am hoping for,
can anyone see an issue
show run
Building configuration...
Current configuration : 1892 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname site1
enable secret 5 $1$XQ0Z$Fzjg/dJ/I1sY5bLjss0l4/
clock summer-time BST recurring last Sun Mar 1:00 last Sun Oct 2:00
ip subnet-zero
ip domain name xxxxxx
ip ssh time-out 60
ip ssh authentication-retries 2
ip ssh version 2
aaa new-model
aaa authentication login xxxxx
aaa session-id common
dot11 ssid XXXXXX
max-associations 1
authentication open
authentication key-management wpa
infrastructure-ssid
wpa-psk ascii xxxxxxxxxxxxxxxxxxx
username Cisco password 7 047802150C2E
username xxxxxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid xxxxx
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
no power client local
power client 50
power local cck 50
power local ofdm 30
channel 2452
station-role root bridge
cca 75
concatenation
distance 1
antenna receive right
antenna transmit right
antenna gain 13
world-mode dot11d country GB outdoor
infrastructure-client
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
full-duplex
bridge-group 1
bridge-group 1 spanning-disabled
hold-queue 80 in
interface BVI1
ip address 192.168.1.1 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
line vty 0 4
end
show run
Building configuration...
Current configuration : 1815 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname xxxxx
enable secret 5 $1$SN2n$CLPRLRzAjlUD47jR1ugca.
clock summer-time BST recurring last Sun Mar 1:00 last Sun Oct 2:00
ip subnet-zero
ip domain name xxxxxx
ip name-server 1.1.1.1
ip ssh time-out 60
ip ssh authentication-retries 2
ip ssh version 2
aaa new-model
aaa authentication login xxxxx
aaa session-id common
dot11 ssid xxxxx
max-associations 1
authentication open
authentication key-management wpa
infrastructure-ssid
wpa-psk ascii xxxxx
username Cisco password 7 062506324F41
username xxxxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid xxxxxx
parent 1 003a.9a21.a8b0
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
station-role non-root bridge
antenna receive left
antenna transmit right
antenna gain 13
world-mode dot11d country GB outdoor
infrastructure-client
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
full-duplex
bridge-group 1
bridge-group 1 spanning-disabled
hold-queue 80 in
interface BVI1
ip address 192.168.1.2 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
line vty 0 4
end
Regards NeilHi Scott,
Yes they are very close together, about a meter to be exact,
Sorry im by no means clued up on wireless, so im guessing your after these
e#show dot11 associations all-client
Address : 003a.9a21.b4c0 Name : xxxxxx
IP Address : 192.168.1.2 Interface : Dot11Radio 0
Device : 11g-bridge Software Version : 12.3
CCX Version : NONE
State : Assoc Parent : self
SSID : xxxxxxxx VLAN : 0
Hops to Infra : 1 Association Id : 4
Clients Associated: 1 Repeaters associated: 0
Tunnel Address : 0.0.0.0
Key Mgmt type : WPA PSK Encryption : TKIP
Current Rate : 54.0 Capability : WMM ShortHdr ShortSlot
Supported Rates : 1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
Voice Rates : disabled
Signal Strength : -31 dBm Connected for : 135 seconds
Signal to Noise : 67 dBm Activity Timeout : 30 seconds
Power-save : Off Last Activity : 0 seconds ago
Apsd DE AC(s) : NONE
Packets Input : 101726 Packets Output : 198208
Bytes Input : 10283192 Bytes Output : 257691877
Duplicates Rcvd : 0 Data Retries : 10049
Decrypt Failed : 0 RTS Retries : 0
MIC Failed : 0 MIC Missing : 0
Packets Redirected: 0 Redirect Filtered: 0
Session timeout : 0 seconds
Reauthenticate in : never
the above is after issuing the power statements
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid xxxxxx
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
no power client local
power client 1
power local cck 1
power local ofdm 1
station-role root bridge
cca 75
concatenation
distance 1
antenna receive right
antenna transmit right
antenna gain 13
world-mode dot11d country GB outdoor
infrastructure-client
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid xxxx
parent 1 003a.9a21.a8b0
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
no power client local
power client 1
power local cck 1
power local ofdm 1
station-role non-root bridge
antenna receive right
antenna transmit right
antenna gain 13
world-mode dot11d country GB outdoor
infrastructure-client
bridge-group 1
bridge-group 1 spanning-disabled
end
or
show int dot 0
Dot11Radio0 is up, line protocol is up
Hardware is 802.11G Radio, address is 003a.9a21.a8b0 (bia 003a.9a21.a8b0)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 21/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:07:23, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 36
Queueing strategy: fifo
Output queue: 0/30 (size/max)
5 minute input rate 105000 bits/sec, 224 packets/sec
5 minute output rate 4630000 bits/sec, 440 packets/sec
231658 packets input, 14164388 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
448016 packets output, 581607544 bytes, 0 underruns
16 output errors, 0 collisions, 4 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
I can serperate them by atlease 10 meters down the hallway... , What is the likely hood of actually getting 54.0 when they are deployed, Distance no more that 1Km) how do these stats look?
Neil -
I have a 1310 wireless bridge....when I power it up, it sometimes does not boot up. The I LED will just sit there and blink and the R and E LEDs will blink in unison with it. After a while just the I LED blinks. I cannot find any literature that tells me if this is an error code or not.
Also, when the thing does boot up, it tells me that the Radio interface is down and disabled, when in fact if you go into the settings of the radio interface, it is selected to be enabled.
What might be going on here?
Thank you.No, there is nothing on the console port when the thing is in the condition described above.
If I do get a successful boot, I can then access via a console port. I may try to reinstall firmware and see if that fixes the problem.
So you are saying the radio link will show as disabled/down until it actually tries to associate/authenticate with another bridge unit? That is normal? -
WPA2-EAP and WPA2-PSK supported Access Points
Dear Team,
I have been looking to find the Cisco Access Points that support both:
WPA2-EAP: Encryption: AES, Authentication: IEEE 802.1X
WPA2-PSK: Encryption: AES, Authentication: PSK (Pre Shared Key) with more than 21 Characters, combined with MAC address filtering.
I am confused about this and need help, please advise.
Regards,
FarhanSure. Go HERE. Click on the APs you want and go to their individual Data Sheets. Use Ctrl+F and enter "WPA2" (or whatever features you want).
-
"Restart Now" IOS command for 1310 Wireless Bridge
I have 2 Cisco Aironet 1310 wireless bridges setup, line-of-sight, 3/4 mile apart, one as Root, the other as Non-Root. Occasionally they drop their connection but a hard restart of either or both bridges will reestablish the connection. What is the equivalent IOS command to the
"GUI > System Software > System Configuration > Restart Now" command? I would like to be able to telnet to either/both units and issue/script the appropriate command.the command is "reload"
BRIDGE# reload
Regards
Surendra -
Power Injector for 1310 wireless bridge
Hello,
We have a failed power injector on a 1310 series bridge. Will the "Power Injector LR" from a 1410 series bridge work on the 1310?
Thank you,
MattNo... both have a different output and should not be used interchangeably.
See this post by Surendra:
https://supportforums.cisco.com/message/3280050#3280050
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Hi there, I cannot open bridge and I get this warning, "Adobe Bridge Cannot be Opened because of a problem. Check with the developer to make sure Adobe Bridge CC works with this version of Mac OS X. You may need to reinstall any updates for this application and Mac OS X" although bridge has been running on my Mac for over a yera. I have installed all current updates for Mac and reinstalled Bridge again from CC and still get the same issue? Any advice?
Would you please provide details about your setup?
BOILERPLATE TEXT:
Note that this is boilerplate text.
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
etc.,
someone may be able to help you (not necessarily this poster).
a screen shot of your settings or of the image could be very helpful too.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks! -
My husband uses adobe cs5. The clone tool isn't working and after resetting the tools adobe bridge now goes to picasa. How can we make the clone tool work and have bridge go to cs5 not picasa?
A lot more information about your hardware and software is needed.
BOILERPLATE TEXT:
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CC", but something like CC2014.v.2.2) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
a screen shot of your settings or of the image could be very helpful too,
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks! -
Raw and TIFF Thumbnails Not Showing in Bridge CS4
Hi,
I just bought Photoshop CS4 and installed. I got an installation error and had to remove and reinstall CS4 (and ran the Mac Cleanup Utility in between). Then, CS4 installed successfully.
Now, when I fire up Bridge CS4, I can preview JPG files, but not TIFF or RAW (*.NEF format from my D200) files.
Has this happened to anyone else and is there a fix I can apply? I have installed known updates for CS4 and have purged the cache.
I have tried searching adobe and the online communities for this issue, but haven't been able to locate it. The problem also applies to *.PSD documents. I have also tried Tools>Cache>Purge Cach for Folder xxx and this doesn't fix things.
Thanks in advance for your advice!!!
BrandonJust found that exchange with Ian. It apparently was milder than I remember, so it has not been deleted:
http://forums.adobe.com/message/1208904#1208904
and
http://forums.adobe.com/message/1208905#1208905
64.
Mar 2, 2009 9:37 PM
in response to: (Tom_Hogarty)
Re: Camera Raw 5.2 and DNG Converter Available - Note from Adobe
Ian,
OK, I'm back already.
The bug was easily and instantly reproduced just as I wrote earlier:
With one of the lines under the thumbnails (thumbnail view in
Bridge) set to date created, and the other three to Date Modified,
Pixel Dimensions and Color Profile, respectively. I then invoked the
Global Purge cache command in Bridge CS4. Poof! The date created line
under each and every thumbnail is now blank. The space for the line is there, but it's totally empty,
blank. >:(
Invoking
Tools > Cache > Build and Export Cache > for all folders and subfolders restores the data in the blanked lines wiped out by the global Purge Cache command in Bridge preferences.
Thank goodness I had disconnected the FW drives.
I then went again and repeated the procedure one more time. The
Date Created line was again immediately left blank under all
thumbnails.
As far as I'm concerned,
the Global Purge cache command in Bridge Preferences in CS4 is broken
, just as it was in CS3 at least until someone tells me how to stop this from happening, reliably and consistently.
Tiger 10.4.11. Dual bootable, DP MDD 1.25GHz G4 (2004),
maxed out at 2GB of RAM, both Spotlight and Dashboard disabled,
Photoshop primary scratch disk on dedicated 160GB internal drive, at
least 100GB available on each of the four internal drives, up to 300GB
on some. Counting external FW drives just over 1TB of drive space
available. nVidia GeForce 7800 GS 425MHz 256 MB graphics display card.
Processor napping enabled through CHUD 3.5.2.
and
65.
Mar 2, 2009 9:50 PM
in response to: (Tom_Hogarty)
Re: Camera Raw 5.2 and DNG Converter Available - Note from Adobe
Oh, shingles! >:(
I just reconnected my FireWire drive and, to my utter disgust and
horror, the Date Created was wiped out under who knows how many
thousands of images. >:( This despite having unmounted, disconnected
and turned off the FW drive, and despite having my Bridge Preferences
> Cache > Options > set to A
utomatically Export Cache To Folders When Possible.
I'm one
very
unhappy camper, Ian. >:(
finally:
66.
Mar 2, 2009 11:20 PM
in response to: (Tom_Hogarty)
Re: Camera Raw 5.2 and DNG Converter Available - Note from Adobe
At
11:12pm, one hour and twenty minutes later (grrrrrrrrrr! >:(),
Bridge has finally rebuilt the cache for every darned file on my FW
drive, restoring through the Tools > Cache > Build and Export Cache > for all folders and subfolders command the blank
Date Created line under each file that the global Purge Command in Bridge Preferences had wiped out.
Ian, I won't trust you next time. :/*
* [emphasis added]
67.
Mar 3, 2009 1:39 AM
in response to: (Tom_Hogarty)
Re: Camera Raw 5.2 and DNG Converter Available - Note from Adobe
Actually, I just thought Bridge had finished. It was still going in the background after midnight. What a bummer! -
How to show rating dots and file name underneath thumbnail in Bridge CS4 preview workspace?
How to show rating dots and file name underneath thumbnail in Bridge CS4 preview workspace?
Thank you! That was it. The option to change it is not available in preferences (though I believe it was in early CS versions). It's hidden in a dropdown menu associated with an icon at the top. It sure wasn't easy to find, and I probably would not have done so without your lead. Thanks again!
-
My bridge is not working normally and keep given me this message : bridge encountered a problem and is unable to read the cache . Please try purging the central cache in cache preferences to correct the situation
And did you then actually purge the cache?
Please realize that you have given ZERO details.
BOILERPLATE TEXT:
Note that this is boilerplate text.
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
a screen shot of your settings or of the image could be very helpful too.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!
Maybe you are looking for
-
I have recently bought a reburbished iMac ( installed with Mountain Lion) and successfully transferred the content of my old imac ( snow leopard) using migration assistant. This onlt took an 1.5 hours. I have noe connected up an external USB drive an
-
Resulta que cuando tengo que conectarme em iCloud desde la web http://www.icloud.com toda va perfecto.. El problema esta cuando lo quiero hacer desde el pc. Me baje iCloud de la web oficial de apple (version windows), lo instalo y cuando quiero acced
-
Would working from a locked project file cause problems?
Hi all. working in FCP 4.5 on numerous Dual G5s (2.0 & 1.8 GHz) with sufficient RAM (4 GB+). I'm working on a large project with a number of editors and I've created projects that each editor can use as references to the material. I lock the referenc
-
Flash Player Installer Is Atrocious
Flash Player Installer absolutely sucks! It is without doubt the worst program I have to interact with on a regular basis. First, you have to download the installer. 17 Mb!!! Talk about bloatware! I guess cable modem users might not complain, but
-
IPhone 4S Blurry Photos w/Flash
My wife has a 64GB iPhone 4S; mine is the 16GB model. Mine takes great photos, with or without flash. Hers takes nice photos without the flash, but every shot taken with her flash turned on comes out blurry. Is there a setting somewhere we've not see