EAP-FAST Security level
Hi all,
I use EAP-FAST in my network and I have some questions about it.
1) is there any vulnerability detected with EAP-FAST?
2) Can I restrict the establishment two or more simultaneous sessions using the same account and same PAC? how
3) Can I use EAP-FAST with MAC address filtering through ACS?
4) What is the level of security provided by EAP-FAST? is there technology more security than EAP-FAST?
Thanks for your reply.
Thanks.
1)
Everything should be fine with EAP-FAST but you should take into consideration some issues when your clients are being provisioned their PACs through inband PAC provisioning.
What will happen? see
The in-band provisioning mode operates inside a TLS tunnel raised by Anonymous DH or Authenticated DH or RSA algorithm for key agreement.
To minimize the risk of exposing the user's credentials, a clear text password should not be used outside of the protected tunnel. Therefore, EAP-MSCHAPv2 or EAP-GTC are used to authenticate the user's credentials within the protected tunnel. The information contained in the PAC is also available for further authentication sessions after the inner EAP method has completed.
Automatic In-Band PAC Provisioning, which is the same as EAP-FAST phase zero, sends a new PAC to an end-user client over a secured network connection. Automatic In-Band PAC Provisioning requires no intervention of the network user or an ACS administrator, provided that you configure ACS and the end-user client to support Automatic In-Band PAC Provisioning.
In general, phase zero of EAP-FAST does not authorize network access. In this general case, after the client has successfully performed phase zero PAC provisioning, the client must send a new EAP-FAST request in order to begin a new round of phase one tunnel establishment, followed by phase two authentication.
However, if you choose the Accept Client on Authenticated Provisioning option, ACS sends a RADIUS Access-Accept (that contains an EAP Success) at the end of a successful phase zero PAC provisioning, and the client is not forced to reauthenticate again. This option can be enabled only when the Allow Authenticated In-Band PAC Provisioning option is also enabled.
Because transmission of PACs in phase zero is secured by MSCHAPv2 authentication, when MSCHAPv2 is vulnerable to dictionary attacks, we recommend that you limit use of Automatic In-Band PAC Provisioning to initial deployment of EAP-FAST.
After a large EAP-FAST deployment, PAC provisioning should be done manually to ensure the highest security for PACs.
EAP-FAST has been enhanced to support an authenticated tunnel (by using the server certificate) inside which PAC provisioning occurs. The new cipher suites that are enhancements to EAP-FAST, and specifically the server certificate, are used.
2) Max user sessions
3)Yes
4)PEAP ( EAP TLS )
Side note:
EAP FAST is now supported on Micrsofot supplicants , so yeah it should work with third party supplicants
Please make sure to rate correct answers and rate the thread as answered
Similar Messages
-
NAC-L2-802.1x (EAP-FAST) and Cisco Secure Services Client 5.0 in wired net
Hi!
(Sorry, if this is a wrong forum.)
Does anybody have any success with Cisco SSC and EAP-FAST in the wired network?
I'm going to use NAC, so I'm trying to set up EAP-FAST. I see the pop-up window on the client to enter user credentials and I see a lot of "debug radius" messages on my 3750 12.2(44)SE switch:
Access-Requests with User-Name="anonymous"
Access-Challenges (I see certificate is sent from ACS)
Access-Reject
CS ACS Failed Attempts Report shows "ACS user unknown" failure for "anonymous".
So far as I understood, EAP-FAST is a tunneled method and it uses "anonymous" to protect user's identity during phase 0 / phase 1 transactions. The actual username is sent in phase 2 transaction.
The following is excerpt from the CS ACS documentation:
"EAP-FAST can protect the username in all EAP-FAST transactions. ACS does not perform user authentication based on a username that is presented in phase one; however, whether the username is protected during phase one depends on the end-user client. If the end-user client does not send the real username in phase one, the username is protected. The Cisco Aironet EAP-FAST client protects the username in phase one by sending FAST_MAC address in place of the username. After phase one of EAP-FAST, all data is encrypted, including username information that is usually sent in clear text."
SSC 5.0 is indeed set up with "Unprotected Identity Pattern"=anonymous and "Protected Identity Pattern"=[username] using sscManagementUtility.exe
So, the question is: Why is ACS 4.1 trying to authenticate username "anonymous" if it knows that the user is fake? Does anybody have working configuaration for EAP-FAST in a wired network?
Any help is greatly appreciated.Correct, ACS database wasn't selected on the NAP Authentication page. It works now, but I constantly get the following message in the Windows event log: "The Cisco Secure Services Client service hung on starting". This is Windows 2000 Advanced Server system with SP4. SSC was set up with no domain authentication, no machine authentication, single sign-on. After some time the SSC service starts, but at that time my PC is already put into the guest VLAN by the switch (the tx-period is 10 seconds):
POD1-SW#sh run int fa1/0/1
Building configuration...
Current configuration : 378 bytes
interface FastEthernet1/0/1
switchport access vlan 999
switchport mode access
dot1x mac-auth-bypass
dot1x pae authenticator
dot1x port-control auto
dot1x timeout reauth-period server
dot1x timeout tx-period 10
dot1x reauthentication
dot1x critical
dot1x critical recovery action reinitialize
dot1x guest-vlan 91
dot1x critical vlan 11
spanning-tree portfast
end
After all the VLAN is reassigned by the switch, but the delay is too high. How can I troubleshoot this?
Thx. -
EAP-FAST on Local Radius Server : Can't Get It Working
Hi all
I'm using an 877w router (flash:c870-advsecurityk9-mz.124-24.T4.bin) as local radius server and have followed various config guides on CCO. LEAP works fine but I just can't get EAP-FAST to work.
I'm testing with win7 client using anyconnect secure mobility client, and also a mac book pro but without luck.
the router sees unknown auth type, and when I run some debugs it talks of unknown eap type 3
sh radius local-server s
Successes : 1 Unknown usernames : 0
Client blocks : 0 Invalid passwords : 0
Unknown NAS : 0 Invalid packet from NAS: 17
NAS : 172.27.44.1
Successes : 1 Unknown usernames : 0
Client blocks : 0 Invalid passwords : 0
Corrupted packet : 0 Unknown RADIUS message : 0
No username attribute : 0 Missing auth attribute : 0
Shared key mismatch : 0 Invalid state attribute: 0
Unknown EAP message : 0 Unknown EAP auth type : 17
Auto provision success : 0 Auto provision failure : 0
PAC refresh : 0 Invalid PAC received : 0
Can anyone suggest what I might be doing wrong?
Regs, TimThanks Nicolas, relevant snippets from config:
aaa new-model
aaa group server radius rad_eap
server 172.27.44.1 auth-port 1812 acct-port 1813
aaa authentication login eap_methods group rad_eap
aaa authorization exec default local
aaa session-id common
dot11 ssid home
vlan 3
authentication open eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa
ip dhcp pool home
import all
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 194.74.65.68 194.74.65.69
ip inspect name ethernetin tcp
ip inspect name ethernetin udp
ip inspect name ethernetin pop3
ip inspect name ethernetin ssh
ip inspect name ethernetin dns
ip inspect name ethernetin ftp
ip inspect name ethernetin tftp
ip inspect name ethernetin smtp
ip inspect name ethernetin icmp
ip inspect name ethernetin telnet
interface Dot11Radio0
no ip address
encryption vlan 1 mode ciphers aes-ccm tkip
encryption vlan 2 mode ciphers aes-ccm tkip
encryption vlan 3 mode ciphers aes-ccm tkip
broadcast-key vlan 1 change 30
broadcast-key vlan 2 change 30
broadcast-key vlan 3 change 30
ssid home
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
interface Dot11Radio0.3
encapsulation dot1Q 3
no cdp enable
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 spanning-disabled
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
interface Vlan3
no ip address
bridge-group 3
interface BVI3
ip address 192.168.1.1 255.255.255.0
ip inspect ethernetin in
ip nat inside
ip virtual-reassembly
radius-server local
no authentication mac
nas 172.27.44.1 key 0 123456
user test1 nthash 0 B151E8FF684B4F376C018E632A247D84
user test2 nthash 0 F2EEAE1D895645B819C9FD217D0CA1F9
user test3 nthash 0 0CB6948805F797BF2A82807973B89537
radius-server host 172.27.44.1 auth-port 1812 acct-port 1813 key 123456
radius-server vsa send accounting -
Mac OS X 10.4.8 adds EAP-FAST support
From the release notes of Mac OS X 10.4.8 update:
http://docs.info.apple.com/article.html?artnum=304200
- Improves security by adding support for EAP-FAST for AirPort wireless authentication.Mac OS X 10.4.8 is now out, and many people were
hoping that Apple would take the opportunity to
update iSync at the same time.
After examining this update I can confirm that iSync
remains at v2.3 and no new phone support has been
added.
Therefore Sony Ericsson M600, P990 and W950 owners
still have no way to iSync their phones. (For
workarounds
see here.
Owners of Sony Ericsson W850, K610, K510, K800, W300,
W700, K790, V630, Z550 and Z525 phones can continue
to use the iSync Phone Plugins available below to
sync these models:
http://mobile.feisar.com/phoneplugins23.html
Jools
This is really bad news! Apple is disappointing a whole lot of new phone owners. I bought my first Apple computer especially for Isync and Ical. Now it seems that the users are no longer important. Innovation and big numbers are the new targets.
Without the proper use of Ical and Isync, OS X becomes incomplete and therefore less interesting for all users.
I think Apple is making a big mistake here!
I’m not willing to let Apple decide witch phone to buy!
So how about it Steve?
Powerbook G4 Mac OS X (10.4.7) -
Connect to EAP-FAST corporate network
Hi. I'm trying to setup my new macbook to connect to my company's wireless network but no luck. Here are the details from my WinXP laptop's Intel PROSet profile:
+Enterprise Security:+
+Wireless Network Name (SSID): protected+
+Network Authentication: Open+
+Data Encryption: CKIP+
+Authentication Type: EAP-FAST+
+Desable EAP-FAST Enhancments (CCXv4): checked+
+Allow unauthenticated provisioning: checked+
+Default server: ACS_wifi+
+User Credentials: Use Windows logon+
+Server Verification is not required.+
*Any idea how to setup my macbook/airport to connect to this network?*
ThanksI've already did try to create there various profiles but no luck. Even when I try 'Join other network' and select 'Show networks' I don't get my corporate network on the list. Maybe it's hidden. Where I can see a Log what's going on?
-
Cisco 871w, radius server local, and leap or eap-fast will not authenticate
Hello, i trying to setup eap-fast or leap on my 871w. i belive i have it confiured correctly but i can not get any device to authenticate to router. Below is the confiureation that i being used. any help would be welcome!
! Last configuration change at 15:51:30 AZT Wed Jan 4 2012 by testtest
! NVRAM config last updated at 15:59:37 AZT Wed Jan 4 2012 by testtest
version 12.4
configuration mode exclusive auto
service nagle
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service linenumber
service pt-vty-logging
service sequence-numbers
hostname router871
boot-start-marker
boot-end-marker
logging count
logging message-counter syslog
logging buffered 4096
logging rate-limit 512 except critical
logging console critical
enable secret 5 <omitted>
aaa new-model
aaa group server radius rad-test3
server 192.168.16.49 auth-port 1812 acct-port 1813
aaa authentication login default local
aaa authentication login eap-methods group rad-test3
aaa authorization exec default local
aaa session-id common
clock timezone AZT -7
clock save interval 8
dot11 syslog
dot11 ssid test2
vlan 2
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 <omitted>
dot11 ssid test1
vlan 1
authentication open
authentication key-management wpa
wpa-psk ascii 7 <omitted>
dot11 ssid test3
vlan 3
authentication open eap eap-methods
authentication network-eap eap-methods
no ip source-route
no ip gratuitous-arps
ip options drop
ip dhcp bootp ignore
ip dhcp excluded-address 192.162.16.49 192.162.16.51
ip dhcp excluded-address 192.168.16.33
ip dhcp excluded-address 192.168.16.1 192.168.16.4
ip dhcp pool vlan1pool
import all
network 192.168.16.0 255.255.255.224
default-router 192.168.16.1
domain-name test1.local.home
lease 4
ip dhcp pool vlan2pool
import all
network 192.168.16.32 255.255.255.240
default-router 192.168.16.33
domain-name test2.local.home
lease 0 6
ip dhcp pool vlan3pool
import all
network 192.168.16.48 255.255.255.240
default-router 192.168.16.49
domain-name test3.local.home
lease 2
ip cef
ip inspect alert-off
ip inspect max-incomplete low 25
ip inspect max-incomplete high 50
ip inspect one-minute low 25
ip inspect one-minute high 50
ip inspect udp idle-time 15
ip inspect tcp idle-time 1800
ip inspect tcp finwait-time 30
ip inspect tcp synwait-time 60
ip inspect tcp block-non-session
ip inspect tcp max-incomplete host 25 block-time 2
ip inspect name firewall tcp router-traffic
ip inspect name firewall ntp
ip inspect name firewall ftp
ip inspect name firewall udp router-traffic
ip inspect name firewall pop3
ip inspect name firewall pop3s
ip inspect name firewall imap
ip inspect name firewall imap3
ip inspect name firewall imaps
ip inspect name firewall smtp
ip inspect name firewall ssh
ip inspect name firewall icmp router-traffic timeout 10
ip inspect name firewall dns
ip inspect name firewall h323
ip inspect name firewall hsrp
ip inspect name firewall telnet
ip inspect name firewall tftp
no ip bootp server
no ip domain lookup
ip domain name local.home
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip accounting-threshold 100
ip accounting-list 192.168.16.0 0.0.0.31
ip accounting-list 192.168.16.32 0.0.0.15
ip accounting-list 192.168.16.48 0.0.0.15
ip accounting-transits 25
login block-for 120 attempts 5 within 60
login delay 5
login on-failure log
memory free low-watermark processor 65536
memory free low-watermark IO 16384
username testtest password 7 <omitted>
archive
log config
logging enable
logging size 255
notify syslog contenttype plaintext
hidekeys
path tftp://<omitted>/archive-config
write-memory
ip tcp synwait-time 10
ip ssh time-out 20
ip ssh authentication-retries 2
ip ssh logging events
ip ssh version 2
bridge irb
interface Loopback0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
interface Null0
no ip unreachables
interface FastEthernet0
switchport mode trunk
shutdown
interface FastEthernet1
switchport mode trunk
shutdown
interface FastEthernet2
shutdown
spanning-tree portfast
interface FastEthernet3
spanning-tree portfast
interface FastEthernet4
description Cox Internet Connection
ip address dhcp
ip access-group ingress-filter in
ip access-group egress-filter out
no ip redirects
no ip unreachables
no ip proxy-arp
ip accounting access-violations
ip flow ingress
ip flow egress
ip inspect firewall out
ip nat outside
ip virtual-reassembly
ip tcp adjust-mss 1460
load-interval 30
duplex auto
speed auto
no cdp enable
interface Dot11Radio0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 2 mode ciphers aes-ccm
encryption key 1 size 128bit 7 <omitted> transmit-key
encryption mode wep mandatory
broadcast-key vlan 1 change <omitted> membership-termination
broadcast-key vlan 3 change <omitted> membership-termination
broadcast-key vlan 2 change <omitted> membership-termination
ssid test2
ssid test1
ssid test3
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
rts threshold 2312
no cdp enable
interface Dot11Radio0.1
description <omitted>
encapsulation dot1Q 1 native
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.2
description <omitted>
encapsulation dot1Q 2
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 spanning-disabled
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
interface Dot11Radio0.3
description <omitted>
encapsulation dot1Q 3
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 spanning-disabled
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
interface Vlan1
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan2
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 2
bridge-group 2 spanning-disabled
interface Vlan3
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 3
bridge-group 3 spanning-disabled
interface BVI1
description <omitted>
ip address 192.168.16.1 255.255.255.224
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
interface BVI2
description <omitted>
ip address 192.168.16.33 255.255.255.240
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
interface BVI3
description <omitted>
ip address 192.168.16.49 255.255.255.240
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
no ip http server
no ip http secure-server
ip http secure-ciphersuite 3des-ede-cbc-sha rc4-128-sha
ip http timeout-policy idle 5 life 43200 requests 5
ip flow-top-talkers
top 10
sort-by bytes
ip nat inside source list 1 interface FastEthernet4 overload
ip nat inside source static tcp 192.168.16.50 80 interface FastEthernet4 80
ip nat inside source static tcp 192.168.16.50 53 interface FastEthernet4 53
ip nat inside source static tcp 192.168.16.50 3074 interface FastEthernet4 3074
ip nat inside source static udp 192.168.16.50 3074 interface FastEthernet4 3074
ip nat inside source static udp 192.168.16.50 88 interface FastEthernet4 88
ip nat inside source static udp 192.168.16.50 53 interface FastEthernet4 53
ip access-list extended egress-filter
deny ip any host <omitted>
deny ip any host <omitted>
deny ip host <omitted> any
deny ip host <omitted> any
remark ----- Bogons Filter -----
deny ip 0.0.0.0 0.255.255.255 any
deny ip 10.0.0.0 0.10.9.255 any
deny ip 10.0.0.0 0.10.13.255 any
deny ip 127.0.0.0 0.255.255.255 any
deny ip 169.254.0.0 0.0.255.255 any
deny ip 172.16.0.0 0.15.255.255 any
deny ip 192.0.0.0 0.0.0.255 any
deny ip 192.0.2.0 0.0.0.255 any
deny ip 192.168.0.0 0.0.15.255 any
deny ip 192.168.0.0 0.0.255.255 any
deny ip 198.18.0.0 0.1.255.255 any
deny ip 198.51.100.0 0.0.0.255 any
deny ip 203.0.113.0 0.0.0.255 any
deny ip 224.0.0.0 31.255.255.255 any
remark ----- Internal networks -----
permit ip <omitted> 0.0.0.3 any
deny ip any any log
ip access-list extended ingress-filter
remark ----- To get IP form COX -----
permit udp any eq bootps any eq bootpc
deny icmp any any log
deny udp any any eq echo
deny udp any eq echo any
deny tcp any any fragments
deny udp any any fragments
deny ip any any fragments
deny ip any any option any-options
deny ip any any ttl lt 4
deny ip any host <omitted>
deny ip any host <omitted>
deny udp any any range 33400 34400
remark ----- Bogons Filter -----
deny ip 0.0.0.0 0.255.255.255 any
deny ip 10.0.0.0 0.255.255.255 any
deny ip 127.0.0.0 0.255.255.255 any
deny ip 169.254.0.0 0.0.255.255 any
deny ip 172.16.0.0 0.15.255.255 any
deny ip 192.0.0.0 0.0.0.255 any
deny ip 192.0.2.0 0.0.0.255 any
deny ip 192.168.0.0 0.0.255.255 any
deny ip 198.18.0.0 0.1.255.255 any
deny ip 198.51.100.0 0.0.0.255 any
deny ip 203.0.113.0 0.0.0.255 any
deny ip 224.0.0.0 31.255.255.255 any
remark ----- Internal networks -----
deny ip 10.10.10.0 0.0.0.255 any
deny ip 10.10.11.0 0.0.0.255 any
deny ip 10.10.12.0 0.0.0.255 any
deny ip any any log
access-list 1 permit 192.168.16.0 0.0.0.63
access-list 20 permit 127.127.1.1
access-list 20 permit 204.235.61.9
access-list 20 permit 173.201.38.85
access-list 20 permit 216.229.4.69
access-list 20 permit 152.2.21.1
access-list 20 permit 130.126.24.24
access-list 21 permit 192.168.16.0 0.0.0.63
radius-server local
no authentication mac
eapfast authority id <omitted>
eapfast authority info <omitted>
eapfast server-key primary 7 <omitted>
nas 192.168.16.49 key 7 <omitted>
group rad-test3
vlan 3
ssid test3
user test nthash 7 <omitted> group rad-test3
user testtest nthash 7 <omitted> group rad-test3
radius-server attribute 32 include-in-access-req format %h
radius-server host 192.168.16.49 auth-port 1812 acct-port 1813 key 7 <omitted>
radius-server vsa send accounting
control-plane host
control-plane transit
control-plane cef-exception
control-plane
bridge 1 protocol ieee
bridge 1 route ip
bridge 2 protocol ieee
bridge 2 route ip
bridge 3 protocol ieee
bridge 3 route ip
line con 0
password 7 <omitted>
logging synchronous
no modem enable
transport output telnet
line aux 0
password 7 <omitted>
logging synchronous
transport output telnet
line vty 0 4
password 7 <omitted>
logging synchronous
transport preferred ssh
transport input ssh
transport output ssh
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
process cpu threshold type total rising 80 interval 10 falling 40 interval 10
ntp authentication-key 1 md5 <omitted> 7
ntp authenticate
ntp trusted-key 1
ntp source FastEthernet4
ntp access-group peer 20
ntp access-group serve-only 21
ntp master 1
ntp server 152.2.21.1 maxpoll 4
ntp server 204.235.61.9 maxpoll 4
ntp server 130.126.24.24 maxpoll 4
ntp server 216.229.4.69 maxpoll 4
ntp server 173.201.38.85 maxpoll 4
endso this what i am getting now for debug? any thoughs?
010724: Jan 5 16:26:04.527 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/2
010725: Jan 5 16:26:08.976 AZT: RADIUS: No response from (162.168.16.49:1812,1813) for id 1645/2
010726: Jan 5 16:26:08.976 AZT: RADIUS/DECODE: No response from radius-server; parse response; FAIL
010727: Jan 5 16:26:08.976 AZT: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
010728: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAIL
010729: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
010730: Jan 5 16:26:08.976 AZT: Client d8b3.7759.0488 failed: EAP reason 1
010731: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: Failed client d8b3.7759.0488 with aaa_req_status_detail 1
010732: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for d8b3.7759.0488
010733: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client d8b3.7759.0488
010734: Jan 5 16:26:08.976 AZT: EAPOL pak dump tx
010735: Jan 5 16:26:08.976 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0004
010736: Jan 5 16:26:08.976 AZT: EAP code: 0x4 id: 0x1 length: 0x0004
0AD05650: 01000004 04010004 ........
0AD05660:
010737: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: sending data to requestor status 1
010738: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010739: Jan 5 16:26:08.980 AZT: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
010740: Jan 5 16:26:08.980 AZT: dot11_auth_dot1x_send_client_fail: Authentication failed for d8b3.7759.0488
010741: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: sending data to requestor status 0
010742: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: client FAILED to authenticate d8b3.7759.0488, node_type 64 for application 0x1
010743: Jan 5 16:26:08.980 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010744: Jan 5 16:26:08.984 AZT: %DOT11-7-AUTH_FAILED: Station d8b3.7759.0488 Authentication failed
010745: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010746: Jan 5 16:26:09.624 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010747: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: req->auth_type 0
010748: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010749: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010750: Jan 5 16:26:09.624 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010751: Jan 5 16:26:09.624 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010752: Jan 5 16:26:09.624 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010753: Jan 5 16:26:09.624 AZT: EAPOL pak dump tx
010754: Jan 5 16:26:09.624 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010755: Jan 5 16:26:09.624 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0AD05B50: 01000031 01010031 ...1...1
0AD05B60: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0AD05B70: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0AD05B80: 72383731 2C706F72 7469643D 30 r871,portid=0
010756: Jan 5 16:26:09.644 AZT: dot11_auth_send_msg: sending data to requestor status 1
010757: Jan 5 16:26:09.648 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010758: Jan 5 16:26:09.648 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010759: Jan 5 16:26:09.656 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010760: Jan 5 16:26:09.656 AZT: EAPOL pak dump rx
010761: Jan 5 16:26:09.656 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0009
010762: Jan 5 16:26:09.656 AZT: EAP code: 0x2 id: 0x1 length: 0x0009 type: 0x1
0B060D50: 01000009 02010009 ........
0B060D60: 01746573 74 .test
010763: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(CLIENT_WAIT,CLIENT_REPLY) for d8b3.7759.0488
010764: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_send_response_to_server: Sending client d8b3.7759.0488 data to server
010765: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_send_response_to_server: Started timer server_timeout 60 seconds
010766: Jan 5 16:26:09.664 AZT: RADIUS/ENCODE(00000198):Orig. component type = DOT11
010767: Jan 5 16:26:09.664 AZT: RADIUS: AAA Unsupported Attr: ssid [282] 8
010768: Jan 5 16:26:09.664 AZT: RADIUS: 74 6F 79 73 6F 6E [toyson]
010769: Jan 5 16:26:09.664 AZT: RADIUS: AAA Unsupported Attr: interface [175] 3
010770: Jan 5 16:26:09.664 AZT: RADIUS: 36 [6]
010771: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Config NAS IP: 192.168.16.49
010772: Jan 5 16:26:09.664 AZT: RADIUS/ENCODE(00000198): acct_session_id: 408
010773: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Config NAS IP: 192.168.16.49
010774: Jan 5 16:26:09.664 AZT: RADIUS(00000198): sending
010775: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Send Access-Request to 162.168.16.49:1645 id 1645/3, len 133
010776: Jan 5 16:26:09.664 AZT: RADIUS: authenticator BF 69 DD DF 89 1F C6 FB - EF EC 12 EB C5 3F 3A CD
010777: Jan 5 16:26:09.664 AZT: RADIUS: User-Name [1] 6 "test"
010778: Jan 5 16:26:09.664 AZT: RADIUS: Framed-MTU [12] 6 1400
010779: Jan 5 16:26:09.664 AZT: RADIUS: Called-Station-Id [30] 16 "0019.3075.e660"
010780: Jan 5 16:26:09.664 AZT: RADIUS: Calling-Station-Id [31] 16 "d8b3.7759.0488"
010781: Jan 5 16:26:09.668 AZT: RADIUS: Service-Type [6] 6 Login [1]
010782: Jan 5 16:26:09.668 AZT: RADIUS: Message-Authenticato[80] 18
010783: Jan 5 16:26:09.668 AZT: RADIUS: 5B FA 47 07 0E E3 4B 71 7F 60 6E 4E 91 37 84 A6 [[?G???Kq?`nN?7??]
010784: Jan 5 16:26:09.668 AZT: RADIUS: EAP-Message [79] 11
010785: Jan 5 16:26:09.668 AZT: RADIUS: 02 01 00 09 01 74 65 73 74 [?????test]
010786: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]
010787: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port [5] 6 661
010788: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port-Id [87] 5 "661"
010789: Jan 5 16:26:09.668 AZT: RADIUS: NAS-IP-Address [4] 6 192.168.16.49
010790: Jan 5 16:26:09.668 AZT: RADIUS: Nas-Identifier [32] 11 "router871"
010791: Jan 5 16:26:14.501 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010792: Jan 5 16:26:19.018 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010793: Jan 5 16:26:23.739 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010794: Jan 5 16:26:28.700 AZT: RADIUS: Fail-over to (162.168.16.49:1812,1813) for id 1645/3
router871#
010795: Jan 5 16:26:33.629 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010796: Jan 5 16:26:38.494 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010797: Jan 5 16:26:39.794 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010798: Jan 5 16:26:39.794 AZT: EAPOL pak dump rx
010799: Jan 5 16:26:39.794 AZT: EAPOL Version: 0x1 type: 0x1 length: 0x0000
0AD053D0: 01010000 ....
010800: Jan 5 16:26:39.798 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,EAP_START) for d8b3.7759.0488
010801: Jan 5 16:26:39.798 AZT: dot11_auth_dot1x_ignore_event: Ignore event: do nothing
router871#
010802: Jan 5 16:26:43.007 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010803: Jan 5 16:26:47.336 AZT: RADIUS: No response from (162.168.16.49:1812,1813) for id 1645/3
010804: Jan 5 16:26:47.336 AZT: RADIUS/DECODE: No response from radius-server; parse response; FAIL
010805: Jan 5 16:26:47.336 AZT: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
010806: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAIL
010807: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
010808: Jan 5 16:26:47.336 AZT: Client d8b3.7759.0488 failed: EAP reason 1
010809: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: Failed client d8b3.7759.0488 with aaa_req_status_detail 1
010810: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for d8b3.7759.0488
010811: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client d8b3.7759.0488
010812: Jan 5 16:26:47.336 AZT: EAPOL pak dump tx
010813: Jan 5 16:26:47.336 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0004
010814: Jan 5 16:26:47.336 AZT: EAP code: 0x4 id: 0x1 length: 0x0004
0B060710: 01000004 04010004 ........
0B060720:
010815: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: sending data to requestor status 1
010816: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010817: Jan 5 16:26:47.340 AZT: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
010818: Jan 5 16:26:47.340 AZT: dot11_auth_dot1x_send_client_fail: Authentication failed for d8b3.7759.0488
010819: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: sending data to requestor status 0
010820: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: client FAILED to authenticate d8b3.7759.0488, node_type 64 for application 0x1
router871#
010821: Jan 5 16:26:47.340 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010822: Jan 5 16:26:47.344 AZT: %DOT11-7-AUTH_FAILED: Station d8b3.7759.0488 Authentication failed
010823: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010824: Jan 5 16:26:47.972 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010825: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: req->auth_type 0
010826: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010827: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010828: Jan 5 16:26:47.976 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010829: Jan 5 16:26:47.976 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010830: Jan 5 16:26:47.976 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010831: Jan 5 16:26:47.976 AZT: EAPOL pak dump tx
010832: Jan 5 16:26:47.976 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010833: Jan 5 16:26:47.976 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0AD05B50: 01000031 01010031 ...1...1
0AD05B60: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0AD05B70: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0AD05B80: 72383731 2C706F72 7469643D 30 r871,portid=0
010834: Jan 5 16:26:47.996 AZT: dot11_auth_send_msg: sending data to requestor status 1
010835: Jan 5 16:26:47.996 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010836: Jan 5 16:26:47.996 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010837: Jan 5 16:26:47.996 AZT: dot11_auth_client_abort: Received abort request for client d8b3.7759.0488
010838: Jan 5 16:26:47.996 AZT: dot11_auth_client_abort: Aborting client d8b3.7759.0488 for application 0x1
router871#
010839: Jan 5 16:26:47.996 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
router871#
010840: Jan 5 16:26:58.634 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010841: Jan 5 16:26:58.634 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010842: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: req->auth_type 0
010843: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010844: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010845: Jan 5 16:26:58.638 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010846: Jan 5 16:26:58.638 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010847: Jan 5 16:26:58.638 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010848: Jan 5 16:26:58.638 AZT: EAPOL pak dump tx
010849: Jan 5 16:26:58.638 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010850: Jan 5 16:26:58.638 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0B060710: 01000031 01010031 ...1...1
0B060720: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0B060730: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0B060740: 72383731 2C706F72 7469643D 30 r871,portid=0
010851: Jan 5 16:26:58.658 AZT: dot11_auth_send_msg: sending data to requestor status 1
010852: Jan 5 16:26:58.658 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010853: Jan 5 16:26:58.658 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010854: Jan 5 16:27:01.603 AZT: dot11_auth_client_abort: Received abort request for client d8b3.7759.0488
010855: Jan 5 16:27:01.603 AZT: dot11_auth_client_abort: Aborting client d8b3.7759.0488 for application 0x1
010856: Jan 5 16:27:01.603 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010857: Jan 5 16:27:02.179 AZT: %SEC-6-IPACCESSLOGP: list ingress-filter denied tcp 32.42.41.254(57443) -> 72.201.117.84(59652), 1 packet
010858: Jan 5 16:27:02.179 AZT: %SEC-6-IPACCESSLOGP: list egress-filter denied tcp 22.3.184.118(0) -> 74.125.53.188(0), 4 packets
010859: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010860: Jan 5 16:27:12.261 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010861: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: req->auth_type 0
010862: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010863: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010864: Jan 5 16:27:12.261 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010865: Jan 5 16:27:12.261 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010866: Jan 5 16:27:12.261 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010867: Jan 5 16:27:12.261 AZT: EAPOL pak dump tx
010868: Jan 5 16:27:12.261 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010869: Jan 5 16:27:12.261 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0B060FD0: 01000031 01010031 ...1...1
0B060FE0: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0B060FF0: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0B061000: 72383731 2C706F72 7469643D 30 r871,portid=0
010870: Jan 5 16:27:12.285 AZT: dot11_auth_send_msg: sending data to requestor status 1
010871: Jan 5 16:27:12.285 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010872: Jan 5 16:27:12.285 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010873: Jan 5 16:27:12.293 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010874: Jan 5 16:27:12.293 AZT: EAPOL pak dump rx
010875: Jan 5 16:27:12.293 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0009
010876: Jan 5 16:27:12.293 AZT: EAP code: 0x2 id: 0x1 length: 0x0009 type: 0x1
0AD05290: 01000009 02010009 ........
0AD052A0: 01746573 74 .test
010877: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(CLIENT_WAIT,CLIENT_REPLY) for d8b3.7759.0488
010878: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_send_response_to_server: Sending client d8b3.7759.0488 data to server
010879: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_send_response_to_server: Started timer server_timeout 60 seconds
010880: Jan 5 16:27:12.301 AZT: RADIUS/ENCODE(0000019B):Orig. component type = DOT11
010881: Jan 5 16:27:12.305 AZT: RADIUS: AAA Unsupported Attr: ssid [282] 8
010882: Jan 5 16:27:12.305 AZT: RADIUS: 74 6F 79 73 6F 6E [toyson]
010883: Jan 5 16:27:12.305 AZT: RADIUS: AAA Unsupported Attr: interface [175] 3
010884: Jan 5 16:27:12.305 AZT: RADIUS: 36 [6]
010885: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Config NAS IP: 192.168.16.49
010886: Jan 5 16:27:12.305 AZT: RADIUS/ENCODE(0000019B): acct_session_id: 411
010887: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Config NAS IP: 192.168.16.49
010888: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): sending
010889: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Send Access-Request to 162.168.16.49:1645 id 1645/4, len 133
010890: Jan 5 16:27:12.305 AZT: RADIUS: authenticator 6F 6C 63 31 88 DE 30 A2 - C2 06 12 EB 50 A3 53 36
010891: Jan 5 16:27:12.305 AZT: RADIUS: User-Name [1] 6 "test"
010892: Jan 5 16:27:12.305 AZT: RADIUS: Framed-MTU [12] 6 1400
010893: Jan 5 16:27:12.305 AZT: RADIUS: Called-Station-Id [30] 16 "0019.3075.e660"
010894: Jan 5 16:27:12.305 AZT: RADIUS: Calling-Station-Id [31] 16 "d8b3.7759.0488"
010895: Jan 5 16:27:12.305 AZT: RADIUS: Service-Type [6] 6 Login [1]
010896: Jan 5 16:27:12.305 AZT: RADIUS: Message-Authenticato[80] 18
010897: Jan 5 16:27:12.305 AZT: RADIUS: 9D D5 62 1A 38 13 94 30 3A 43 D7 A4 AE A4 43 64 [??b?8??0:C????Cd]
010898: Jan 5 16:27:12.305 AZT: RADIUS: EAP-Message [79] 11
010899: Jan 5 16:27:12.305 AZT: RADIUS: 02 01 00 09 01 74 65 73 74 [?????test]
010900: Jan 5 16:27:12.305 AZT: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]
010901: Jan 5 16:27:12.305 AZT: RADIUS: NAS-Port [5] 6 664
010902: Jan 5 16:27:12.309 AZT: RADIUS: NAS-Port-Id [87] 5 "664"
010903: Jan 5 16:27:12.309 AZT: RADIUS: NAS-IP-Address [4] 6 192.168.16.49
010904: Jan 5 16:27:12.309 AZT: RADIUS: Nas-Identifier [32] 11 "router871"
010905: Jan 5 16:27:16.642 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/4 -
Is it possible to use eap-fast authentication with CCKM on 7920 phone with WLC.
It is working when configuring 802.1x and wep 104 bits on controller but it does not work with wpa1+wpa2.If the client doesn't have a PAC and automatic PAC provisioning is enabled on the ACS, then the first authentication attempt will result in a failure, which is the session where the client will receive the PAC. The 7920 only supports automatic PAC provisioning. The default PAC settings should be ok, but may want to decrease or increase based on company's security policy. Also with CCKM, this will help when roaming with an expired PAC, otherwise there will be a 20 second gap in voice when roaming with an expired PAC, where a new PAC will need to be obtained.
-
Hi,
I have a AP1100 and a repeater AP1100. The AP acts as a Radius server and the clients (all AIR-350) use LEAP, WPA and TKIP. Everything works just fine.
Now I want to secure my environment a bid more and make use of EAP-Fast. I can't get it work. At the authetication process, it sticks at provisioning. The log at the AP only shows: debugging; Station xxxxx: Authentication failed.
Does anybody have a clue what I'm doing wrong or is it because the AP is the Radius server i.c.w. EAP-Fast ?
Thanks,
AudenCisco Secure ACS is listed as a Prerequisite and in the Required Hardware and Software section;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a0080262422.html#wp998531
hth
Required Hardware and Software
The following software and hardware are required for configuring EAP-FAST.
Cisco Aironet Client Utility (ACU) and Aironet
Aironet Client Utility version 6.3
Cisco Aironet 350 Series Client Adapter
Client adapter firmware version 5.40
Client driver version 8.5
Aironet Client Monitor (ACM) version 2.3
Windows XP, SP1
Cisco Aironet Access Point
Cisco Aironet 1100 Series Access Point
Cisco IOS Software Release 12.2(13)JA3
CiscoSecure Access Control Server (ACS)
CiscoSecure ACS v3.2.3 for Windows 2000 SP4
Aironet Configuration Administration Tool (ACAT) (optional)
Cisco Aironet ACAT v1.3 -
EAP-Fast or PEAP ??
Dear All,
we are not sure if we should use EAP-FAST as authentication method or if we should use PEAP or EAP/TTLS. Could you please inform us which one is safer ? For PEAP or EAP/TTLS we would need a Radius Server such as ACS while we could assign an Access Point as local authentication server if we used EAP-Fast. Is the extra cost for an ACS server justified only to be able to use PEAP ? Thanks for your help.Also you don?t need ACS for PEAP. MS IAS can do that for you. The thing about ACS is that
it is there for many other things thatn wireless. TACACS authentication on you devices, security logs. VPN authentication, and can connect OTP solutions on top of ACS (From other vendors like RSA) When migrating from LEAP EAP-FAST is the easiest way to go since EAP-FAST was designed to take over LEAP with less impact on your configuration and migration is easy since you are then running a ACS. The market acctually demanded EAP-FAST cause there was need for a solution that was mroe secure than LEAP and PEAP-mschapv2 (both shared secret mecanisms) and something less complicated that PKI solutions. The answer was EAP-FAST with its easy to setup "mini certificate" setup which can be preety well automated. PKI PEAP with certificates is a major decission and you have to be ready to manage a PKI solution all year long. This might require extra presonell to take care of it. But of course those solution will be the most secure.
regards. Kristjan Edvardsson
Sensa ehf. Cisco Silver Partner -
ISE - EAP-FAST PAC Provisioning - Identity field??
Hi all, very simple question regarding the fields in the PAC provisioning section of ISE. Basically wondering what the "identity" field under machine and tunnel PAC is meant to be? I am currently planning an EAP-FAST deployment and this is the only area I am wondering about. Essentially planning to auto-provision the PAC hopefully using authenticate in-band. The Cisco doco is a little vague on this particular field.
Thanks in advance - have googled this for a day or so and frankly cannot find the information that I want.Use
PAC
•Tunnel PAC Time To Live—The Time to Live (TTL) value restricts the lifetime of the PAC. Specify the lifetime value and units. The default is 90 days. The range is between 1 and 1825 days.
•Proactive PAC Update When: of PAC TTL is Left—The Update value ensures that the client has a valid PAC. Cisco ISE initiates an update after the first successful authentication but before the expiration time that is set by the TTL. The update value is a percentage of the remaining time in the TTL. The default is 90%.
•Allow Anonymous In-band PAC Provisioning—Check this check box for Cisco ISE to establish a secure anonymous TLS handshake with the client and provision it with a PAC by using phase zero of EAP-FAST with EAP-MSCHAPv2. To enable anonymous PAC provisioning, you must choose both of the inner methods, EAP-MSCHAPv2 and EAP-GTC.
•Allow Authenticated In-band PAC Provisioning—Cisco ISE uses SSL server-side authentication to provision the client with a PAC during phase zero of EAP-FAST. This option is more secure than anonymous provisioning but requires that a server certificate and a trusted root CA be installed on Cisco ISE.
When you check this option, you can configure Cisco ISE to return an Access-Accept message to the client after successful authenticated PAC provisioning.
–Server Returns Access Accept After Authenticated Provisioning—Check this check box if you want Cisco ISE to return an access-accept package after authenticated PAC provisioning.
•Allow Machine Authentication—Check this check box for Cisco ISE to provision an end-user client with a machine PAC and perform machine authentication (for end-user clients who do not have the machine credentials). The machine PAC can be provisioned to the client by request (in-band) or by the administrator (out-of-band). When Cisco ISE receives a valid machine PAC from the end-user client, the machine identity details are extracted from the PAC and verified in the Cisco ISE external identity source. Cisco ISE only supports Active Directory as an external identity source for machine authentication. After these details are correctly verified, no further authentication is performed.
When you check this option, you can enter a value for the amount of time that a machine PAC is acceptable for use. When Cisco ISE receives an expired machine PAC, it automatically reprovisions the end-user client with a new machine PAC (without waiting for a new machine PAC request from the end-user client).
•Enable Stateless Session Resume—Check this check box for Cisco ISE to provision authorization PACs for EAP-FAST clients and always perform phase two of EAP-FAST (default = enabled).
Uncheck this check box in the following cases:
–If you do not want Cisco ISE to provision authorization PACs for EAP-FAST clients
–To always perform phase two of EAP-FAST
When you check this option, you can enter the authorization period of the user authorization PAC. After this period, the PAC expires. When Cisco ISE receives an expired authorization PAC, it performs phase two EAP-FAST authentication.
•Preferred EAP Protocol—Check this check box to choose your preferred EAP protocols from any of the following options: EAP-FAST, PEAP, LEAP, EAP-TLS, and EAP-MD5. By default, LEAP is the preferred protocol to use if you do not enable this field. -
Other LEAP upgrade options besides PEAP and EAP-FAST?
Currently I'm using LEAP for authentication on my AP's at roughly 200 remote locations, with about 6 AP's per site. These are performing local Radius authentication on the AP's themselves. We are using non-dictionary passwords, so I'm not too worried about a ASLEAP attack. However, I've been asked to look into other alternatives besides LEAP for security.
Here's the problem.... there is no way my company will pay for a Radius server at each individual location. As both PEAP and EAP-FAST seem to require an actual Radius server as opposed to an AP acting as one, to use either means authentication would have to happen back to the central office servers over our WAN. That is going to generate an unacceptable amount of WAN traffic, as well as leave us stranded should the WAN connection go down, as happens to at least one site once a week or so. Do I have any other options, are are they superior to my current LEAP setup?A comparable system might be to use WPA - PSK (Pre-Shared Key) w/ TKIP.
TKIP will keep the key rotation, and if you start with a strong PSK, you should be OK. WPA - PSK doesn't need a RADIUS server or certificates to work.
Pre-shared keys could conceivably be defeated by a brute force attack, but you can control that aspect somewhat with a lockout after X number of failed attempts.
You could also toss on some MAC filtering but, depending on your user base, it can be an administrative nightmare.
If all of your remote sites are tied back to your home network, you could try a central RADIUS, and local Certificate Authority (both can be on an existing WIN2K or better server) at the home office, then use the remote RADIUS on the AP to proxy the requests back to the home office.
There are a couple approaches depending on your specific environment. Without a CA and RADIUS server (that supports certificates - I don't think the AP RADIUS does), your options are fairly limited. LEAP and WPA-PSK are probably as good as you're like to get.
Good Luck
Scott -
Limitations/Issues to use LEAP/EAP-Fast with Airespace
Hello
are there any important limitations or issues to use with cisco a/b/g Card the authentication methodes LEAP or EAP-FAST.
Any input is welcome
OliverI would suggest that you use LEAP for the client adapters. It is easy to implement and is also secure.
-
EAP-FAST is now in 10.4.9
The fix for EAP-FAST is suppose to be in 10.4.9.
the last network update to 10.4.8 had it.I have had the system hang on an Intel iMac running OS 10.4.9, with latest Security Updates, after importing an image into Photoshop CS3 via firewire connection to an Epson scanner. No problem previously with the firewire scanner on an iMac G5 running OS 10.4.9. Since everything was more or less updated at the same time, not sure where the problem lies. The scan is complete and just as the image opens in Photoshop, the system hangs, and Force-Quit doesn't work. The Force Quit dialogue box shows 'Photoshop is not responding'. I've had to manually shut down the system by holding the power button down. This has all happened within the last few days, and the issue appears intermittently--some scans complete normally.
-
ASA 5505 Interface Security Level Question
I am wondering if someone can shed some light on this for me. I have a new ASA 5505 with a somewhat simple config. I want to set up a guest VLAN on it for a guest wireless connection.
I set up the ASA with the VLAN, made a trunk port, set up DHCP (on the ASA) on the guest VLAN, configured NAT, etc. Everything seem to be working with that. Guests are getting address on the correct subnet, etc.
The only issue I have is that the Guest VLAN (192.168.22.0) can get to the secure (VLAN1 - 172.16.0.0). I set up the guest VLAN (VLAN 5) with a security level of 10, the secure with a level of 100. I figured that would be enough. To stop the guest from accessing the secure, I had to throw on an ACL (access-list Guest-VLAN_access_in line 1 extended deny ip any 172.16.0.0 255.255.255.0)
Can someone show me what I did wrong?
Thank you for any help!
To create the VLAN, I did the following:
int vlan5
nameif Guest-VLAN
security-level 10
ip address 192.168.22.1 255.255.255.0
no shutdown
int Ethernet0/1
switchport trunk allowed vlan 1 5
switchport trunk native vlan 1
switchport mode trunk
no shutdown
below is the whole config.
Result of the command: "sho run"
: Saved
ASA Version 9.1(3)
hostname ciscoasa
enable password zGs7.eQ/0VxLuSIs encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
switchport trunk allowed vlan 1,5
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 172.16.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address <External IP/Mask>
interface Vlan5
nameif Guest-VLAN
security-level 10
ip address 192.168.22.1 255.255.255.0
boot system disk0:/asa913-k8.bin
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Inside_Server1_80
host <Inside_server1_IP>
object network Inside_Server1_25
host <Inside_server1_IP>
object network Inside_Server1_443
host <Inside_server1_IP>
object network Inside_Server1_RDP
host <Inside_server1_IP>
object service RDP
service tcp destination eq 3389
object network Outside_Network1
host <Outside_Network_IP>
object network Outside_Network2
host <Outside_Network_IP>
object network Outside_Network2
host <Outside_Network_IP>
object network TERMINALSRV_RDP
host <Inside_server2_IP>
object network Inside_Server2_RDP
host <Inside_Server2_IP>
object-group network Outside_Network
network-object object Outside_Network1
network-object object Outside_Network2
object-group network RDP_Allowed
description Group used for hosts allowed to RDP to Inside_Server1
network-object object <Outside_Network_3>
group-object Outside_Network
object-group network SBS_Services
network-object object Inside_Server1_25
network-object object Inside_Server1_443
network-object object Inside_Server1_80
object-group service SBS_Service_Ports
service-object tcp destination eq www
service-object tcp destination eq https
service-object tcp destination eq smtp
access-list inside_access_in extended permit ip any any
access-list outside_access_in extended permit object-group SBS_Service_Ports any object-group SBS_Services
access-list outside_access_in extended permit object RDP any object TERMINALSRV_RDP
access-list outside_access_in extended permit object RDP object-group RDP_Allowed object Inside_Server1_RDP
access-list outside_access_in extended permit object RDP object-group RDP_Allowed object Inside_Server2_RDP
access-list Guest-VLAN_access_in extended deny ip any 172.16.0.0 255.255.255.0
access-list Guest-VLAN_access_in extended permit ip any any
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu Guest-VLAN 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-714.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network obj_any
nat (inside,outside) dynamic interface
object network Inside_Server1_80
nat (inside,outside) static interface service tcp www www
object network Inside_Server1_25
nat (inside,outside) static interface service tcp smtp smtp
object network Inside_Server1_443
nat (inside,outside) static interface service tcp https https
object network Inside_Server1_RDP
nat (inside,outside) static interface service tcp 3389 3389
object network TERMINALSRV_RDP
nat (inside,outside) static <TerminalSRV_outside)IP> service tcp 3389 3389
object network Inside_Server2_RDP
nat (inside,outside) static interface service tcp 3389 3390
nat (Guest-VLAN,outside) after-auto source dynamic obj_any interface
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
access-group Guest-VLAN_access_in in interface Guest-VLAN
route outside 0.0.0.0 0.0.0.0 <Public_GW> 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 172.16.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd auto_config outside
dhcpd address 192.168.22.50-192.168.22.100 Guest-VLAN
dhcpd dns 8.8.8.8 4.2.2.2 interface Guest-VLAN
dhcpd lease 43200 interface Guest-VLAN
dhcpd enable Guest-VLAN
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 129.6.15.30 prefer
username <Username> VAn7VeaGHX/c7zWW encrypted privilege 15
class-map global-class
match default-inspection-traffic
policy-map global-policy
class global-class
inspect icmp
inspect icmp error
inspect pptp
service-policy global-policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:7f5d70668ebeb94f49f312612f76c943
: endHi,
To my understanding they should not be able to connect to the more secure network IF you DONT have an interface ACL configured.
One very important thing to notice and which I think is the most likely reason this happened is the fact that as soon as you attach an interface ACL to an interface then the "security-level" looses its meaning. The "security-level" has meaning as long as the interface is without an ACL. This makes the "security-level" only usable in very simple setups.
What I think happend is that you have "permit ip any any" ACL on the interface that allowed all the traffic.
Your option is to either remove the interface ACL completely or have the ACL configured like you have now. I mean first block traffic to your secure LAN and then allow all other traffic which would allow the traffic to Internet
Hope this helps
Please do remember to mark a reply as the correct answer if it answered your question.
Feel free to ask more if needed.
- Jouni -
The security level is set to High
Windows 2008R2 terminal Server
Office 2013
Adobe Acrobat XI update 9
When trying to create a PDF from a word document (have not tried other files yet), Adobe hangs for about 2 mins and then gives the following message
The Security Level is set to High
Please run the application which created this document, in the "Security Warning" dialog select the check box "Always trust macros from this source" and enable macro's created by Adobe Systems inc
No 1. There is absolutely no need for an apostrophe in the second instance of the word macros
Have deployed the Adobe Acrobat Administrative template and enabled the following setting
'Automatically Trust Sites for Win OS Security Zones' (Elevates the trusted sites list in Internet Explorer to privileged locations so that they may bypass enhanced security restrictions. When enabled, the trust list is a union of IE's trust list and Acrobat's privileged locations list. GUI mapping: Edit > Preferences > Security (Enhanced) > Automatically trust sites for my Win OS security zones)
- not a fix
Have exported every digital signature from the pdf office dlls and imported to the computer certificate store - not a fix
Have disabled every office macro and security setting - not a fix
Does not matter if the file being converted is on a UNC path, mapped drive, or local drive
Have added all file locations containing office docs to trusted folders in Word and Adobe - not a fix
R-Click context menus for combining and conversion work fine however I understand that this uses the Adobe PDF Printer and not the office addons
Opening a file in Word and converting to a PDF using the Addon is fine as is printing to the PDF Printer
This issue only occurs from within the Adobe Acrobat Application 'Create file from PDF' and currently only seems to affect Office documents
I cannot see how to give Adobe any more trustSolved
I was running Office in a 'RunVirtual' environment. This man explains it best
http://ppe.blogs.technet.com/b/gladiatormsft/archive/2014/02/05/app-v-5-on-run-virtual-rds -run-virtual-virtualizable-ext…
Essentially Office and Acrobat are installed Natively however all Office Apps are configured to run in a Virtual environment so that Office Addins which are true AppV applications can be linked into Office.
My 'Empty' 'RunVirtual Office package did not have 'Com Integration' enabled
Adobe Acrobat makes use of a Com Addin for Office, so Office was unable to expose that to Adobe Acrobat until the 'Empty' 'RunVirtual Office package was updated accordingly
Maybe you are looking for
-
How to tell if a contact blocked or deleted me...
ok, this is rather complicated. A few months ago, when I was using a previous version of Skype, this is what happened: 1. The user appeared as "Away" 2. I could no longer view his number of contacts (though he could have switched this to private)3. H
-
CATEGORIZATION using Alphabets in report
Hi, I have a requirement in report where we need to rate the vendors based on quality and I need to categorize them using alphabets E - EXCELLENT G- GOOD A- AVERAGE P- Poor Need to display these alphabets against each vendor based on their rating. H
-
Nokia 808 pureview- Any future updates for complet...
I saw the Nokia sample image in http://www.dpreview.com/news/2012/02/27/Nokia-808-PureView-with-41MP-sensor how come the pictures can be in ISO 114 - 5.3MP, 16:9? I thought they only have 5mp and ISO 100 or 200. How can I select 101~199 ISO. ISO 58
-
Recordset on html document type
Is it possible to add a Recordset on html page? I know I could convert the document to an ASP page to mke this possible, but I was wondering if it is possible to do this with converting. Cheers.
-
Delivery date in WCEM Quotation
Hi All. We have implemented WCEM , Is there a way to show the requested delivery date in WCEM ? Detailed explanation : We create quotations in CRM which are displayed in WCEM -> My Account -> Quotations . we enter the expected delivery date in Quotat