Early 2011 Macbook Pro screen turns off/on
I was listening to music and doing some homework when the screen turned off and then turned back on. The computer wasn't hot at all when it happened. The music also stopped when it happened. After a few seconds it turned back on and everything went back to normal, I had sound and everything. I'm not exactly sure what happened, battery was at 87% so I'm sure it wasn't that. This is the first instance of it happening. If anyone has any advice or knows anything I could do to ensure it doesn't continue or get worse it'd be very much appreciated.
I thought it might have been an update that triggered it, but I guess not. It could be your hardware, but I would try to dianose software reasons first.... such as something else you were running that triggered a resolution change. Whats involved in "doing your homework"?
Similar Messages
-
My MacBook Pro screen turns off when I open the lid!
This has been driving me nuts, and also apparently Apple as well.
When my MacBook Pro is connected to a power adapter, if I close the lid it sleeps like a good little Mac. When I open the lid, the display comes on instantly. Then after about a second, it goes black. The LED backlight turns off. I can get it to come on using either of two ways: 1) touch either of the brightness buttons, or 2) remove and replace the power connector.
Now, here is the weird part: it only seems to do it when I am logged in as me. If I login as guest, it doesn't happen. That would seem to imply it is something about my profile that causes it to happen. So I whacked ~/Library/Preferences and it still happened. So where is this particular bit of nastiness hiding?OK, so I think I solved my issue. It was caused by the system not going to sleep (The screensaver thing was a dead end).
When I ran the console app pmset, I got something like this:
➜ ~ pmset -g assertions
12-06-29 9:11:06 AM EDT
Assertion status system-wide:
PreventUserIdleDisplaySleep 0
CPUBoundAssertion 0
DisableInflow 0
ChargeInhibit 0
PreventSystemSleep 1
PreventUserIdleSystemSleep 0
ExternalMedia 0
DisableLowPowerBatteryWarnings 0
EnableIdleSleep 1
NoRealPowerSources_debug 0
UserIsActive 0
ApplePushServiceTask 0
The process that was causing PreventSystemSleep to be 1 was "org.cups.cupsd" which is the print service. So I checked all my printers, one of them was "In Use". When I opened it, there weren't any jobs listed. I went through the options and selected Jobs > Show Everyone's Jobs and sure enough there was a job there. I deleted it and everything seems to work now.
The odd thing is that print job was probably from my other account which didn't seem to have this screen problem. Anyway, I hope this helps anyone out there.... -
Hi,
I had this problem since I bought my MacBook Pro 15' (Summer 2009) whenever using the 9600 card. From time to time the monitor simply turns itself off and then comes back on, sometimes after a few seconds, and sometimes after a few minutes. This happens a few times a day, and sometimes it never happens. But usually it happens during sudden temperature increases, like when waking the mac from sleep, or a short while after firing up a game.
Just by sheer chance, I discovered today that if the screen turns itself off, then I can bring the screen back again by pressing slightly on the aluminum body somewhere above the F5 and F6 keys. Doing so while the monitor is on, can also turn it off and then back again.
I am suspecting that there is a bad contact problem between the motherboard and the screen. Any suggestions or courses of actions are appreciated.
Note that this never happens when using the 9400 card.
Thanks in Advance.OK, so I think I solved my issue. It was caused by the system not going to sleep (The screensaver thing was a dead end).
When I ran the console app pmset, I got something like this:
➜ ~ pmset -g assertions
12-06-29 9:11:06 AM EDT
Assertion status system-wide:
PreventUserIdleDisplaySleep 0
CPUBoundAssertion 0
DisableInflow 0
ChargeInhibit 0
PreventSystemSleep 1
PreventUserIdleSystemSleep 0
ExternalMedia 0
DisableLowPowerBatteryWarnings 0
EnableIdleSleep 1
NoRealPowerSources_debug 0
UserIsActive 0
ApplePushServiceTask 0
The process that was causing PreventSystemSleep to be 1 was "org.cups.cupsd" which is the print service. So I checked all my printers, one of them was "In Use". When I opened it, there weren't any jobs listed. I went through the options and selected Jobs > Show Everyone's Jobs and sure enough there was a job there. I deleted it and everything seems to work now.
The odd thing is that print job was probably from my other account which didn't seem to have this screen problem. Anyway, I hope this helps anyone out there.... -
Early 2011 MacBook Pro shutting off all by itself
Early 2011 MacBook Pro 11" shutting off all by itself recently.
I had the logic board replaced 11 months ago because it started to shut off more and more until it refused to boot up again.
Now I am going through the same problem. Is this common?OK, in that case:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Mac OS X 10.6.8 Update Combo v1.1.
Upgrading to Lion or Mountain Lion will not solve the problem. -
Early 2011 Macbook Pro - Black screen at random
I have an early 2011 Macbook Pro, running Mac OS X (10.7.5). Seemingly at random, the screen will go black and the only way to get it back is to hold the power button down. When it turns back on, everything is running as normal. It's been happening more and more frequently, so I'm wondering is this a problem I can fix on my own? Can it be fixed or is it just a glitch I should just deal with?
(Please explain everything to me as if I were a 5-year-old)Early 2011 15" Macbook Pro.
Add me to the long list of customers experiencing display issues. HUGE problems with a blank screen when waking from sleep and difficulty starting up (video glitches & hi fan speed). After about 6 months and 2 genius bar visits I finally did a complete HD wipe/clean install of Mavericks with all of the default settings.
The situation has improved only slightly overall, but at first things were great. I was confident I had it licked.
As I restored apps & profile settings things start to get wonky. The last install I did was Picasa (I thought this app was the culprit before the wipe). I successfully restored my Picasa settings and all was fine. I even closed the lid and when I opened it the next day the screen came right back on. Then I tried to sync my iPhone and BAM! Screen goes out and the system is hung (no response to keystrokes or sound events).
Power button shutdown.
Restarted and the Macbook hung as the previously opened apps reopened.
Power button shutdown again.
Restart this time was normal and everything opened just fine. The console logs show NOTHING indicate any issues or that the machine experienced a kernel panic or anything like that.
It's been 1 whopping 36 hours since my clean install and I've already crashed twice.
But now I use my Macbook with anxiety as I never know when it's going to crap out again. Maybe it's time I switch back to Linux on an inexpensive wintel laptop as I won't buy another Apple laptop if this is the what I should expect from a $2000 machine.
Incidently, I also have a 2010 MB pro which had dispaly issues and Apple replaced the logic board at no cost (out of warranty) as part of a replacement program. I've seen MANY forum posts suggesting that Apple should step up and provide the same level of service for the Early 2011 MB Pros... I tend to agree. -
My Early 2011 Macbook Pro Continues to shut off at random
I own an early 2011 Macbook Pro, 4GB RAM, intel 3000 384mb graphics, 250gb SATA hd. I now have OS X 10.8.2 and my macbook randomly shuts off and its not just once or twice a day. It is more along the lines of over 20 times a day. Can somebody give me some advice to resolve this issue? I used mackeeper and ran every scan and I went to disk utility and repaired the drive. I don't know what else i could possibly do. This issue is making me wish i never bought this mac. The macbook is great and all but now i can't even use it because it shuts off at random. I can't enjoy the macbook if i have to use it in fear that it will shut off at any moment. Can someone please help me with this issue quickly?
If you have Apple Care or are still under warranty, give them a call and get a case number. Otherwise, take the computer to an Apple store or an AASP. Whichever is more convenient for you.
-
Green flicker pixels on my screen (Early 2011 MacBook Pro)
I have a green flicker pixels on my screen (Early 2011 MacBook Pro) when I click on "menu" options at top of screen and very visable when I open a browser. I've update all software, even as recent as the infamous EFI 2.3 update. Please Help! I have not been able to find an answer anywhere!!!
hi did you resolve your flickering pixels issue I have same problem thanks Tim
-
My early 2011 MacBook Pro 15" non-glare display has developed a dark band at the edges of the screen approximately the same width as the aluminum surround. This wasn't present when the MBP was new. I'm near an Apple Store and can take the laptop in, but has anyone else had this problem?
Thanks for your input. I didn't completely flesh out what I'm seeing visually. The resolution settings are all correct for my screen. The problem is if, say, looking at the gray startup screens or a completely white full-screen image, there is a perimeter of graying, almost as if the LEDs are somehow not as bright as the rest. It's also curious that the thickness of this phenomenon is almost exactly the same as the metal bezel around the display. I will be taking it to an Apple Store for a look, as I'm also having several minor hardware problems that need to be addressed and remedied.
-
Early 2011 Macbook Pro shuts off when charger unplugged. Worked fine yesterday.
Hi,
I have an early 2011 Macbook Pro, which I purchased brand new; it's just over one year old. Yesterday the laptop held a charge no problem for 6 hours or more. Today, when I disconnect it from the charger it goes to sleep. When I plug it back in and press the power button it wakes up, and I can use it.
This cannot be a battery issue, since it was holding a charge without trouble yesterday. Does this appear to be a serious issue? My one year warranty expired 2 months ago yesterday, and I had forgot to purchase AppleCare. Sigh. It almost seems like surgically-planned obsolecense or punishment for not purchasing AppleCare.
I would immensely appreciate any help/suggestions on this.
Thanks.OK, in that case:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Mac OS X 10.6.8 Update Combo v1.1.
Upgrading to Lion or Mountain Lion will not solve the problem. -
Early 2011 MacBook Pro- The thermal paste discussion.
It is my goal to clear up the questions and concerns Apple customers have been having regarding heat or fan related concerns with Early 2011 MacBook Pros. If your MacBook Pro was produced within the last few months the thermal issue has been resolved and it will likely not be in issue for you. If you are still wondering if your computer is effected or what the real issue is keep reading.
The MacBook Cools itself by 2 main methods: active and passive. The active cooling is via a fan that blows air through a heatsync and into a tube called a heat pipe which leads to the back of the computer where the hot air is discharged through a vent at the bottom of the screen behind the hinge. The fan lowers the air pressure inside the case causing outside air is drawn in the case, displacing the hot air inside and helping to cool the other components.
The computer uses passive cooling to remove the residual heat from the processor which comes mostly in the form of radiant heat. Passive cooling is also used to cool the other components of the computer (memory, disk drives, battery etc). Passive cooling works by conductive heat transfer ie. syncing to the case of the computer. Some of the heat then is radiated. Some of it is transferred from the outside of the case via convective cooling; the foot pads on the bottom cover are designed to raise it up just enough to allow air underneath for convection to occur. (Convection is the process in which hot air to rises and is displaced by cooler air.) The rest of the heat from the bottom cover is absorbed by whatever surface you have the computer on.
The processor will not sync to the case very much if the board is assembled properly however the other components of the computer will, requiring the case to be in open air to allow for passive cooling to take place.
If you have some sort of covering such as a plastic snap on case it will likely interfere with passive cooling in all of it's 3 of it forms, this will cause the computer to be abnormally hot. I recently saw someone in the Apple store with a MacBook Air experiencing abnormal heating due to a plastic snap case so this particular problem is not unique to MacBook Pros and it is not the cause of the issue being discussed here. I do not recommend the use or anything that covers the computer while it is running with the exception of something that covers the back of the display panel only. If you are worried about your computer getting damaged go and buy a laptop insurance policy from Worth Ave group. The insurance does not cover cosmetic damage or misplaced items but will cover accidental damage including spills. This insurance also covers theft, vandalism and natural disasters, is quite inexpensive and the claims process and deductible is similar to most phone insurance plans (which they also offer).
User induced overheating can also occur when the computer is placed on an improper surface such as a couch cushion, car seat, bed, pillow etc. Doing this can interfere with both passive and active cooling.
As I mentioned earlier In all likelihood if your computer was produced after May it is not affected. I personally have been in posession of 3 MacBook Pros, one produced before May which had the problem, one after which had no problems and one produced more recently that has mind blowing thermal performance way beyond all of my expectations.
So the question at this point is exactly what is the problem, how can it be diagnosed and how can it be rectified.
After extensive research and testing I have determined the issue to be related to improper application thermal paste. I involuntarily became involved in this pursuit as a result of the problems I was experiencing and I did not initially come at from an objective viewpoint but rather one of cautious skepticism. I had anticipated before purchasing my computer that there may be a thermal issue. This anticipaion came as a result of reading an article on ifixit.com about the disassembly of the brand new early 2011 MacBook Pro. When the technician performing the disassembly removed the main heat sync he expressed concern about how much much thermal paste was present, expressing that it seemed excessive. This lead the technician to question wether or not it would cause heating problems.
Proper application of thermal paste is critical to the functionality of the active cooling system and when applied improperly will not properly transfer the heat to the heat-sync which in turn gets cooled by the fan. Proper application of thermal paste insures the heat is removed from the case as efficiently as possible. Doing this both reduces the speed at which the fan needs to run in a lot of situations and prevents too much heat from the processor needing to be cooled by passive means. If is is not applied properly it will eventually lead to overheating of the case as well as the other components of the computer. This can cause damage firstly to the computer's battery and can also significantly shorten the life computer. (Or any other kind of electronic device for that matter.)
The problem can be diagnosed by testing the computer using a program called System Load or any other software that will put your computers proscessor use up to its maximum and keep it there indefinitely. Placing full load on your GPU at the same time during the test is also recommended. Keep in mind, if you are using your computer the fan will spin up if needed for additional cooling. You should expect the fan go up to its maximum speed during the test, it is not in of itself an indication of a negative result. Make sure to have the computer plugged in, fully charged and on a proper surface. A desk or other flat surface should be fine. Exceptions would include the top of a refrigerator since it has insulation just underneath the metal exterior or any surface that is heated by any means such as a dryer or other appliance.
(The temps to follow are in ºF)
Run the test for up to 1 hour. If the case of the computer breaks 93 degrees your unit is likely affected. Expect the unit to even possibly reach temps approaching and exceeding 100º, if this happens immediately abort the test. Also look for the processor temp shooting up to around 180 in the first 30 seconds and the fan spinning up right away. Typically on a properly functioning unit the temperature of the case will end up being somewhere in the neighborhood of 88-91º. If this test is preformed in a room with a normal ambient room temperature of about 68 degrees. Even after an hour the case of the computer should not be significantly hot, just warm to the touch. On a normally operating unit the fan will start to kick in within 90 seconds or so and may not reach full speed even after several minuets.
At one point the case of my computer actually reached 95º during normal web browsing.
This is a problem that I have had successfully corrected twice by reapplication of thermal paste. The first time was on a machine produced prior to may and the second was after a logic board was replaced at the repair depot. (I suspect the inventory turnover is lower for boards than whole computers resulting in a board from the initial production run being installed in my computer.)
If you forget everything I just wrote remember this. #1 if you are using your computer hard enough the fan will end up running at high speed at some point. #2 This problem is not in any way related to the design of the MacBook Pro, or its use/application. #3 This mostly not a problem of the CPU being too hot; these Sandy Bridge CPUs are rated for 212ºf and will routinely be in the neighborhood of 200º, this is hotter than other chips but well within design limits. #4 I have done everything in my power to make sure that this problem has been corrected and I have every logical and evidenced based reason to believe it has been resolved in machines produced after may. #5 This is not an Apple acknolidged issue. Technicians will tell you that there is no problem because these higher temps are normal and within operating limits and if they weren't the machine would shut itself off. (This is a bit extreme; just like a lot of other devices such as electronics, toaster ovens and space heaters with thermal overload protection this automatic shutoff is intended to occur when damage or risk of fire is imminent because the device is WAY outside of normal operating paramaters.) They will also not tell you when asked what these limits are, that they know what they are or in some cases that such figures they even exsist.
I stake my personal and professional reputation on the accuracy of my findings, it is my job as a private consultant to help my clients to resolve complicated and expensive issues just like this one.
Bottom line if you are having a problem and Apple won't fix it on warranty don't ditch your machine, just pay to have it done yourself. In most cases you can pay have it done at the Apple store. It will probably cost you less than 100.00, and it will not void your warranty as long as the work is done by Apple certified technician. It will be well worth it; after all in spite of this MacBook Pro's are hands down the best portable computers on the market, with an industry leading warranty and support to back it up. On it's worst day Apple's service and support is better than any computer/ consumer electronics company, even on its best day.
I hope this helps to clarify this issue! I also hope it will help anyone affected to resolve the problem instead of resorting to a refund and settling for something else.hello all
you can try this:
Go to system preferences > settings > built in display > see bottom of window.
check "show mirroring options in the menu bar when available". then click "airplay display" > and select your device.
That's what happened to my MBP - 15-inch, Late 2011 model. -
My early 2011 Macbook Pro on start up has wifi, but drops it soon after and never comes back, AHT shows nothing wrong. Multiple wifi's tried and same on all. I have also re-installed OSX from scratch and still happens.
I have the same problem. I have a white macbook 2010, with mavericks os. I just found my mac not powering on and then I tried to run it on safe mode by holding the shift button but it will turn off seconds after I let go of the shift button. I am able to access the desktop and use it while holding the shift button the whole time. It's a bit slower than before but I figured maybe it's because of holding down shift button.
I went to the Apple Store to have them look at my mac and I was told it's a failed hard disk. I wasn't told why he was able to conclude that a failed hard disk is causing the problem, I was just told to get a replacement. But the thing is when I ran Disk Utility it says, "disk appears to be okay." So I also feel like it's possible it's not a hard disk issue because it's also the first time it happened. My mac was working perfectly fine before all this.
Do you know anything else that could cause this problem? Were you able to find out what's wrong?
Thanks. -
Airplay mirroring on early 2011 macbook pro not mirroring
First, here's what I have:
Early 2011 macbook pro (identifier 8,3) with 2.2 Intel Core i7 processor connected over Wifi on 2.4 Ghz channel.
OSX 10.8 Mountain Lion
Apple TV 3 (fully up to date)
The stats I've read say airplay mirroring should work fine. I can connect both machines just fine. I can stream movies just fine. I can send music just fine. I just cannot mirror my desktop. I have the icons, a connection is made, but all that shows is a blank screen. I've adjusted the resolutions with no luck. I've shut down and rebooted both machines with no luck...
Any solutions or do I have to count my losses with Apple Airplay and spend more money on a 3rd party alternative (AirParrot)?Hi eoinodonnell,
The problem was resolved, but I have the worst answer... it just started working, and has remained reliable since. I never found out exactly what fixed it, but I would try these things:
1) Try a factory reset on the Apple TV, and make sure your Macbook pro has all the latest updates.
2) Try to repair disk permissions (better to do it from disk utility from boot menu) and reboot your macbook.
3) Backup your files and do a fresh install of OSX.
I know I performed all these tasks, and possibly more, but something along the way did fix the problem.
I hope something here works! If so, please let me know what did it. -
Hi,
I have an early 2011 MacBook Pro. I use Premiere Pro CS5 to video edit on. It's fine but when it comes to grading it's nearly impossible on such a small screen.
I'd like to buy a 27inch external monitor (Asus, Samsung, Dell, whatever - haven't decided yet) for when I'm editing at work (which is most days). My query is regarding the resolutions. Obviously my MacBook Pro displays a resolution of 1280x800, so if I buy a monitor with a resolution of 2560x1440 for example, what gets displayed?
And also does the connecting cable make any difference? For example, if I'm connecting by Thunderbolt out to HDMI, then an HDMI to HDMI cable to the external monitor, what happens then? Or should I be using a Mini Display Port to Display Port connecting lead?
I guess all I really want to know is, will it work? But also, am I wasting my money buying an external monitor with a 2560x1440 resolution? Should I just go for one that's the same res at my MacBook Pro?
I've never really understood how these things all work!
Thanks in advance for anyones help.
Regards,
PhilI think it will work. You would need a mini displayport to (single link) DVI adapter to hook up that monitor.
Not sure what kind of problems you had with the ViewSonic but I'm guessing the Dell is probably a better monitor anyhow. -
I know this question has been asked before. My problem is similar to what is mentioned here but I hope someone can explain the error log attached below and hopefully I'm able to find a DIY solution without much cost.
I'm using a early 2011 MBP with Yosemite installed. Not too long ago, I manually upgraded my hard disk to a OWC SSD.
Recently my MBP screen went into white blank screen AGAIN while I was working on a python script which crawls the web with about 10 threads. I used to run this same script without *much* problems before yosemite (ie: i encounter the same problem with Mavericks but not so frequent. I never install mountain Lion before so I can't comment on that. I came from Snow Leopard to Maverick and Yosemite). Other times, my MBP will go into the same white blank screen while doing other misc stuff and this usually doesn't involved me watching any HD video.
A couple of solutions that get my MBP up and running are:
1) I hard shutdown and bootup my MBP. After the apple logo it freezes at the white blank screen. While it stays in the white screen, I will unplug my power adapter and wait for my battery to drain out completely. Once the battery is completely drained out, I will plug in my power adapter and I'm definitely able to boot up my MBP without any problem the first time. I did the same and thus I'm able to post this question.
2) Bootup into safe mode and restart. It works once
3) I have also disabled dynamic switching of graphics card but that didn't work.
Below is my error report. I don't quite understand it. I hope someone explain to me?
Wed Nov 26 23:00:48 2014
*** Panic Report ***
Machine-check capabilities: 0x0000000000000c09
family: 6 model: 42 stepping: 7 microcode: 40
signature: 0x206a7
Intel(R) Core(TM) i7-2720QM CPU @ 2.20GHz
9 error-reporting banks
Processor 0: IA32_MCG_STATUS: 0x0000000000000004
IA32_MC3_STATUS(0x40d): 0xbe00000000800400
IA32_MC3_ADDR(0x40e): 0x00003f7fa25f70af
IA32_MC3_MISC(0x40f): 0x000000000003ffff
Processor 1: IA32_MCG_STATUS: 0x0000000000000005
IA32_MC3_STATUS(0x40d): 0xbe00000000800400
IA32_MC3_ADDR(0x40e): 0x00003f7fa25f70af
IA32_MC3_MISC(0x40f): 0x000000000003ffff
panic(cpu 0 caller 0xffffff802161f12a): "Machine Check at 0xffffff7fa25f70af, registers:\n" "CR0: 0x000000008001003b, CR2: 0x000000010bd43000, CR3: 0x0000000018e1e03e, CR4: 0x00000000000626e0\n" "RAX: 0x0000000000000000, RBX: 0x0000000000000040, RCX: 0xffffff814f6e042c, RDX: 0xffffff814f6e0340\n" "RSP: 0xffffff812ae23898, RBP: 0xffffff812ae238d0, RSI: 0x0000000000000004, RDI: 0xffffff812b337fd8\n" "R8: 0x0000000000000040, R9: 0x00000000ffffffff, R10: 0x0000000000000000, R11: 0xffffff812b337eec\n" "R12: 0x0000000000000012, R13: 0xffffff812b2d7fd8, R14: 0x0000000000000040, R15: 0xffffff812b2d7fec\n" "RFL: 0x0000000000010202, RIP: 0xffffff7fa25f70af, CS: 0x0000000000000008, SS: 0x0000000000000010\n" "Error code: 0x0000000000000000\n"@/SourceCache/xnu/xnu-2782.1.97/osfmk/i386/trap_native.c:168
Backtrace (CPU 0), Frame : Return Address
0xffffff81034d5cf0 : 0xffffff802153a811
0xffffff81034d5d70 : 0xffffff802161f12a
0xffffff81034d5ed0 : 0xffffff802163acef
0xffffff812ae238d0 : 0xffffff7fa25f91ec
0xffffff812ae23920 : 0xffffff7fa25fbd85
0xffffff812ae23940 : 0xffffff7fa25fc241
0xffffff812ae23990 : 0xffffff7fa22bd0bb
0xffffff812ae239d0 : 0xffffff7fa22bfcb4
0xffffff812ae23aa0 : 0xffffff7fa22c5190
0xffffff812ae23ac0 : 0xffffff7fa22c50dd
0xffffff812ae23ad0 : 0xffffff8021ad8008
0xffffff812ae23b30 : 0xffffff8021b01c92
0xffffff812ae23b60 : 0xffffff8021b02859
0xffffff812ae23bc0 : 0xffffff8021b00003
0xffffff812ae23d00 : 0xffffff80215ea517
0xffffff812ae23e10 : 0xffffff802153e91c
0xffffff812ae23e40 : 0xffffff80215235a3
0xffffff812ae23e90 : 0xffffff8021533e8d
0xffffff812ae23f10 : 0xffffff802160a142
0xffffff812ae23fb0 : 0xffffff802163ac66
Kernel Extensions in backtrace:
com.apple.iokit.IOHIDFamily(2.0)[917971EF-5947-3DF5-BB9F-D353D05C0484]@0xffffff7fa229b000->0xffffff7fa2310fff
dependency: com.apple.driver.AppleFDEKeyStore(28.30)[3BAA7FEE-7EF3-3A9A-A0B1-902A4AB7171F]@0xffffff7fa2290000
com.apple.iokit.IOGraphicsFamily(2.4.1)[6D99A3BE-D531-3780-880B-13F2FC894A4A]@0xffffff7fa25ef000->0xffffff7fa2629fff
dependency: com.apple.iokit.IOPCIFamily(2.9)[766FC23F-452C-3B74-951C-598BB17BCF06]@0xffffff7fa1d24000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
14B25
Kernel version:
Darwin Kernel Version 14.0.0: Fri Sep 19 00:26:44 PDT 2014; root:xnu-2782.1.97~2/RELEASE_X86_64
Kernel UUID: 89E10306-BC78-3A3B-955C-7C4922577E61
Kernel slide: 0x0000000021200000
Kernel text base: 0xffffff8021400000
__HIB text base: 0xffffff8021300000
System model name: MacBookPro8,2 (Mac-94245A3940C91C80)
System uptime in nanoseconds: 44905012498
last loaded kext at 7194739946: org.virtualbox.kext.VBoxNetAdp 4.3.12 (addr 0xffffff7fa4795000, size 28672)
loaded kexts:
org.virtualbox.kext.VBoxNetAdp 4.3.12
org.virtualbox.kext.VBoxNetFlt 4.3.12
org.virtualbox.kext.VBoxUSB 4.3.12
org.virtualbox.kext.VBoxDrv 4.3.12
com.apple.filesystems.autofs 3.0
com.apple.driver.AppleHWSensor 1.9.5d0
com.apple.driver.AppleHDAHardwareConfigDriver 267.0
com.apple.driver.AGPM 100.14.37
com.apple.driver.AppleTyMCEDriver 1.0.2d2
com.apple.driver.AppleMikeyHIDDriver 124
com.apple.driver.AppleHDA 267.0
com.apple.iokit.IOBluetoothSerialManager 4.3.1f2
com.apple.driver.AppleOSXWatchdog 1
com.apple.driver.ApplePolicyControl 3.7.21
com.apple.driver.AppleMikeyDriver 267.0
com.apple.driver.AppleUpstreamUserClient 3.6.1
com.apple.kext.AMDFramebuffer 1.2.8
com.apple.iokit.IOUserEthernet 1.0.1
com.apple.driver.AppleIntelHD3000Graphics 10.0.0
com.apple.AMDRadeonX3000 1.2.8
com.apple.iokit.IOBluetoothUSBDFU 4.3.1f2
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.AppleIntelSNBGraphicsFB 10.0.0
com.apple.driver.AppleThunderboltIP 2.0.2
com.apple.driver.SMCMotionSensor 3.0.4d1
com.apple.driver.AppleSMCPDRC 1.0.0
com.apple.driver.AppleSMCLMU 2.0.4d1
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.3.1f2
com.apple.driver.AppleLPC 1.7.3
com.apple.kext.AMD6000Controller 1.2.8
com.apple.driver.AppleHWAccess 1
com.apple.driver.AppleHV 1
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.AppleMuxControl 3.7.21
com.apple.driver.AppleBacklight 170.4.12
com.apple.driver.AppleMCCSControl 1.2.10
com.apple.driver.AppleUSBTCButtons 240.2
com.apple.driver.AppleUSBTCKeyEventDriver 240.2
com.apple.driver.AppleUSBTCKeyboard 240.2
com.apple.driver.AppleIRController 327.5
com.apple.driver.CoreStorageFsck 471
com.apple.driver.AppleFileSystemDriver 3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 35
com.apple.iokit.SCSITaskUserClient 3.7.0
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.6.5
com.apple.driver.AppleUSBHub 705.4.1
com.apple.driver.AirPort.Brcm4331 800.20.24
com.apple.driver.AppleSDXC 1.6.5
com.apple.iokit.AppleBCM5701Ethernet 10.1.2b3
com.apple.driver.AirPort.Brcm4360 901.19.10
com.apple.driver.AppleFWOHCI 5.5.2
com.apple.driver.AppleAHCIPort 3.0.7
com.apple.driver.AppleUSBEHCI 705.4.14
com.apple.driver.AppleUSBUHCI 656.4.1
com.apple.driver.AppleSmartBatteryManager 161.0.0
com.apple.driver.AppleACPIButtons 3.1
com.apple.driver.AppleRTC 2.0
com.apple.driver.AppleHPET 1.8
com.apple.driver.AppleSMBIOS 2.1
com.apple.driver.AppleACPIEC 3.1
com.apple.driver.AppleAPIC 1.7
com.apple.driver.AppleIntelCPUPowerManagementClient 218.0.0
com.apple.nke.applicationfirewall 161
com.apple.security.quarantine 3
com.apple.security.TMSafetyNet 8
com.apple.driver.AppleIntelCPUPowerManagement 218.0.0
com.apple.kext.triggers 1.0
com.apple.driver.DspFuncLib 267.0
com.apple.kext.OSvKernDSPLib 1.15
com.apple.iokit.IOAudioFamily 200.6
com.apple.vecLib.kext 1.2.0
com.apple.iokit.IOSerialFamily 11
com.apple.iokit.IOAcceleratorFamily2 156.4
com.apple.iokit.IOSurface 97
com.apple.driver.AppleThunderboltEDMSink 4.0.2
com.apple.driver.AppleThunderboltDPOutAdapter 4.0.6
com.apple.driver.AppleSMBusPCI 1.0.12d1
com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.3.1f2
com.apple.iokit.IOBluetoothFamily 4.3.1f2
com.apple.driver.AppleHDAController 267.0
com.apple.iokit.IOHDAFamily 267.0
com.apple.kext.AMDSupport 1.2.8
com.apple.AppleGraphicsDeviceControl 3.7.21
com.apple.iokit.IOUSBUserClient 705.4.0
com.apple.driver.AppleSMC 3.1.9
com.apple.driver.IOPlatformPluginLegacy 1.0.0
com.apple.driver.IOPlatformPluginFamily 5.8.0d49
com.apple.iokit.IOFireWireIP 2.2.6
com.apple.driver.AppleGraphicsControl 3.7.21
com.apple.driver.AppleBacklightExpert 1.1.0
com.apple.iokit.IONDRVSupport 2.4.1
com.apple.driver.AppleSMBusController 1.0.13d1
com.apple.iokit.IOGraphicsFamily 2.4.1
com.apple.driver.AppleUSBMultitouch 245.2
com.apple.iokit.IOUSBHIDDriver 705.4.0
com.apple.driver.CoreStorage 471
com.apple.driver.AppleUSBMergeNub 705.4.0
com.apple.driver.AppleUSBComposite 705.4.9
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.7.0
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.driver.AppleThunderboltDPInAdapter 4.0.6
com.apple.driver.AppleThunderboltDPAdapterFamily 4.0.6
com.apple.driver.AppleThunderboltPCIDownAdapter 2.0.2
com.apple.driver.AppleThunderboltNHI 3.1.7
com.apple.iokit.IOThunderboltFamily 4.2.1
com.apple.iokit.IOAHCISerialATAPI 2.6.1
com.apple.iokit.IOSCSIArchitectureModelFamily 3.7.0
com.apple.iokit.IOEthernetAVBController 1.0.3b3
com.apple.iokit.IO80211Family 700.52
com.apple.driver.mDNSOffloadUserClient 1.0.1b8
com.apple.iokit.IONetworkingFamily 3.2
com.apple.iokit.IOFireWireFamily 4.5.6
com.apple.iokit.IOAHCIFamily 2.7.0
com.apple.iokit.IOUSBFamily 705.4.14
com.apple.driver.AppleEFINVRAM 2.0
com.apple.driver.AppleEFIRuntime 2.0
com.apple.iokit.IOHIDFamily 2.0.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 300.0
com.apple.kext.AppleMatch 1.0.0d1
com.apple.driver.AppleKeyStore 2
com.apple.driver.AppleMobileFileIntegrity 1.0.5
com.apple.driver.AppleCredentialManager 1.0
com.apple.driver.DiskImages 389.1
com.apple.iokit.IOStorageFamily 2.0
com.apple.iokit.IOReportFamily 31
com.apple.driver.AppleFDEKeyStore 28.30
com.apple.driver.AppleACPIPlatform 3.1
com.apple.iokit.IOPCIFamily 2.9
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.corecrypto 1.0
com.apple.kec.Libm 1
com.apple.kec.pthread 1
Model: MacBookPro8,2, BootROM MBP81.0047.B27, 4 processors, Intel Core i7, 2.2 GHz, 8 GB, SMC 1.69f4
Graphics: Intel HD Graphics 3000, Intel HD Graphics 3000, Built-In, 512 MB
Graphics: AMD Radeon HD 6750M, AMD Radeon HD 6750M, PCIe, 1024 MB
Memory Module: BANK 0/DIMM0, 4 GB, DDR3, 1067 MHz, 0x0198, 0x393930353432382D3030352E4130324C4620
Memory Module: BANK 1/DIMM0, 4 GB, DDR3, 1067 MHz, 0x0198, 0x393930353432382D3030352E4130324C4620
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0xD6), Broadcom BCM43xx 1.0 (5.106.98.100.24)
Bluetooth: Version 4.3.1f2 15015, 3 services, 27 devices, 1 incoming serial ports
Network Service: Ethernet, Ethernet, en0
Serial ATA Device: OWC Mercury Electra 6G SSD, 240.06 GB
Serial ATA Device: MATSHITADVD-R UJ-898
USB Device: Hub
USB Device: Apple Internal Keyboard / Trackpad
USB Device: BRCM2070 Hub
USB Device: Bluetooth USB Host Controller
USB Device: FaceTime HD Camera (Built-in)
USB Device: Hub
USB Device: IR Receiver
Thunderbolt Bus: MacBook Pro, Apple Inc., 22.1Hi all, I had many problems with the GPU of my Early 2011 MacBook Pro and the MLB was replaced three times so far. The first time was about a year ago and I went to an authorised retailer and not to an Apple Store. They first incorrectly diagnosed the problem and told me that they had to replace the hard drive. After that, they still did not really find the problem but said that the MLB had to be replaced, which I did given that my computer was only two years old and running fabulously. About a month later the problem reappeared and the MLB was replaced again, this time by using the 3-months guarantee of the MLB. The first time I had to pay. A few weeks ago I again had problems (the computer was very hot and fans were running at maximum speed most of the time although I was running only Mail and Preview). I'm, I took it directly to the Apple Store and after about five minutes of looking at it they decided to replace in the MLB for free. There is no official replacement program but I think Apple has now recognised the issue and they don't charge you anything if you had the issue before (they call this a repeat repair). So good luck if you haven't solved your problem yet. If the problem reappears there should be no problem.
-
My one day old MacBook pro just turned off and it won't come back on either through mains or battery power it's as if the unit is completely dead. Even with the mains plugged in there is no green or orange light to say its charging or full charged. The battery was fully charged anyway seconds before the screen went off.
When you say no green or orange light are you refering to the little led on the magsafe connector? That could mean either the charger/cable are bad or the circuitry in the MBP is faulty. Since this is a brand new MBP best bet is to take it back to an Apple Retail store and have the genius bar staff take a look. They can determine if it needs to be reparired or replaced.
Maybe you are looking for
-
"...in a custom Sequence Preset Editor."
On page 1011 of the Final Cut Express User Manual, in the section "The Export QuickTime Movie Command", in the second paragraph, it suggests that there is a way to create a custom Sequence Preset. I quote: "You can also choose to use the existing set
-
Possible malware/virus in mail?
hi there. until yesterday, my mail-software was working pretty well, even after all the upgrades. all of a sudden, all the different mailboxes and smartboxes disappeared, all the different accounts were gone. i had to do it all over again. something
-
with itunes installed on my computer it freezes/works slowly/it freezes trying to get to itunes store/it freezes working on word or excel....all in all it makes my laptop horrible. when i uninstall it the computer works just fine.......help
-
hi, i tend to have the same problem as many people on the forum, but since i can't find my problem i thought i'd post my own discussion. I installed the master collection succesfully, except for photoshop i get an exit code 7 problem on this install,
-
Quick Copy in Implementation task in display mode
Hi, I am trying to use the Quick copy method to copy data from one DB to another DB.But the categories on the left side are in display mode,How to activate that? If DB Authorization is needed how to do that? Thanks and Regards, S.G.Sekar