Easing the entry of 2 point interpolations into scaling module.

I have a program that I need to check and calibrate the scaling data x1 and x2 frequently .
I would like to make this entry without typing in the voltage setpoints and from the Layout if possible to keep the machine operator out of the worksheet .
Calibration proceedure at the moment.
- I place low tolerance master into tool
-cycle unit
-take the numbers from the voltage digital meter and enter them manualy into the linear scaling module x1 box
-repeat the process with the high tolerance master for the x2 box.
Is it possible to have the scaling setpoints entry made by simply pressing an enter button from the layout after cycling the unit
without having to type the numbers in and hgow could I go about this ?
Thanks Kent.
Attachments:
Volt Cal..DSB ‏94 KB

Yes...
Use Global variables in the Linear Scaling module.
In the Layout window, use the table object, and configure the cell to use the defined global variables, selecting the "Variable" option.
Then, on the layout, when running, enter the value and hit enter to store it
Test it... the scaling module may want you to restart to pick up the value.
- cj
Measurement Computing (MCC) has free technical support. Visit www.mccdaq.com and click on the "Support" tab for all support options, including DASYLab.

Similar Messages

No Entry in Table T510 when the entry should be pointing to T710?

Hello Guruu2019s,
When we process an IT0008 change, we are receiving an error that there is u201CNo Entry in Table T510 for the key 10*###** **** on 2/20/2011u201D. This is a new entry in PM Compensation Management Job pricing  Pay Structures  Define Pay Grades and levels.
With that said, I did not set this up originally and I am new in to this area of configuration. Also, I configured this new entry based on the instructions that were left by the previous co-worker.
Now, from the research that I have done so far, the configuration that I was instructed to key in uses Table T710 which is why I am receiving the No entry in T510. From the entire configuration that I have checked in our system, we have never used table T510. So why it is yelling at me now, I cannot figure that out. I checked the feature TARIF and there is no configuration with any of our employee group/settings, but it is active and the otherwise is calling a program RPCADD00.
Just a little more history, we have been in the process of implementing Performance Management & Enterprise Compensation Management with consultants. The consultants are gone, so I am not sure if they turned something on which is forcing this to look at table T510 now or not?
We are on ECC 6 with EHP4 and any direction would be highly appreciated because I am at a lost here.
Thanks,
Mike

Hi,
On the IT0008 screen menu bar, go to Edit>Change remuneration type. This will toggle between Salary (T710) and Pay Scale (T510). For your case, you need to keep it as Salary.
Hope this helps.
Donnie

In the Full Featured LabVIEW example, what makes the entry point button reappear?

My question is this: What piece of LV code or invoke node for the TS engine makes the Entry Point button reappear when a sequence file is loaded?
Background:
I've inherited a modified version of the Full Featured LabVIEW UI, which has been moderately modified (Enough so that restarting isn't really an option, but it's still similar enough to use them as comparisons for behaviors). Also, this code was started in LV2012/TS2012, and I'm migrating to LV2013/TS2013, but this behavior was consistent in both versions.
Here's what I've tried:
I found that when the Connect Command executes (See attachment), the button, which is a TSUI.IButton control, is gets greyed out or hidden. In the unmodified example UI that's provided with TestStand, the button reappears when a sequence file is loaded. The problem is that when I load a sequence file in my code, and click on it ahead of running, the button does not reappear. In my code, I can run the sequence successfully by right clicking on the sequence file and selecting Run, so I don't believe the sequence has an error, nor the process model.
Thanks in advance,
Seth
Solved!
Go to Solution.
Attachments:
ConnectCommand.JPG ‏56 KB

Seth,
The "options" input of the ConnectCommand function controls this. On the Help page for this input, you can see that there are options for "ignore enable" and "ignore visible". Either of these could impact the functionality of the entry point button. You might try making the options for both buttons 0 and see if this resolves the issue. If not, please let us know.
Daniel E.
TestStand Product Support Engineer
National Instruments

I just update itunes for latest version. Now I can't open it on win 7- 64 bits. I get an erro: Cant find the entry point of the procudere sqlite_wal_checkpoint.. Windows error 127.. help!!!

I just update itunes for latest version. Now I can't open it on windows 7- 64 bits. I get an erro: Cant find the entry point of the procudere sqlite_wal_checkpoint.. Windows error 127. What can I do...???

How did you fix this?

Am gettinI g an error message of apple sync notifer that the entry point sqlite3_3_checkpoint could not be located in the dynamic link library SQLite2.dll/ This message comes up every time I re boot.

getting error message when I boot up of the apple sync notifer that the entry point sqlite3_3 checkpoint could not be located in the dynamic link library SQlite2,dll this message comes up every time I login and I dont know what it means or how to fix and stop the message appearing every time I log in. what does this mean and how do I fic this issue

With that one, perhaps first try uninstalling and reinstalling your MobileMe control panel. Does that clear up the error?

How to get the entry point in the ActiveX/COM adaptor

below is the description of the Demo of using the ActiveX/COM to call new seq .
API Demo
1. Manually add a Message Popup step to the MainSequence of a
new sequence file. Save the sequence file as launch.seq.
2. Create another sequence file and save the file as caller.seq.
3. In the MainSequence of the caller.seq file, add Action steps
using the ActiveX/COM Adapter to call into the TestStand API and
launch the launch.seq file in a new execution.You might need the
following two methods to complete this step.
. Engine.GetSequenceFileEx
. Engine.NewExecution
so the question as follows:
1.i call the method of get sequencefileEx
2. call the method of getmodlesequenceFile
3.call the method of evalEntryPointNameExpression
4.call the method of NewExecution.
but at the step of 3. i haven't get the entry point.
so how to solve this issue? thanks
Attachments:
QQ图片20140115200924.jpg ‏58 KB
QQ图片20140115201708.jpg ‏100 KB

This is a duplicate post of this:
http://forums.ni.com/t5/NI-TestStand/How-to-get-the-entry-point-in-the-ActiveX-COM-adaptor/m-p/27005...

Help me in finding the entry points in the source code of java.....

hi...
I want to design a compilation server and apply some of the optimization technique's like inlining, SSA and others.
So i require to find the entry points in source code from where i can include my code and check the performance of the program at level it is performing .
Please help in this problem....
and i also like to know what are hot methods in java context?

BigDaddyLoveHandles wrote:
Do you even know Java? Why not just let the HotSpot optimization do its thing?Good point, I would try either of two things.
If you have a good understanding of Java internals and are confident you could optimise code better, I suggest you contribute to the OpenJDK and we can all benefit.
Otherwise I suggest you try using the optimisation built into the compiler and the JVM.
Note: the JVM optimises the code dramatically in ways most normal people won't have thought possible.
The compiler doesn't optimise the code so much as it leaves this job to the JVM.
Two examples;
- say you call a small method often. The JVM can inline this method for you. (the same way a compiler would) However say this method can be over-ridden and later your program calls a different implementation, it can inline both methods even if the new method in a new class didn't exist when the first method was inlined.
- In a 32-bit JVM, 32-bit registers and references are used. In a 64-bit JVM 64-bit registers and references are used without needing to recompile the code. However there is a third option of using 32-bit references in a 64-bit JVM. In this case, it assumes the bottom 3 bits are always 000 so it shifts the reference down 3 bits allowing you to access 32 GB using 32-bit references. Again, you can use this with libraries which were compiled before 64-bit JVMs were available.

"ZENNW32.DLL is misssing the entry point nwappLoadOD."

We are getting the error
"ZENNW32.DLL is misssing the entry point nwappLoadOD."
I have found this in some other threads in this forum, but they did
not go
in a useful direction for me. This error message is appearing on a
WinXP Pro
workstation before the NWgina appears after boot up. Zen policies are
not
working.
The history of this error is that we installed SP1b on ZfD 4. We thenupdated our workstations from client 4.83 to 4.9 and afterwards the
Zen
agent to the MSI version shipping with SP1b. I have tried deleting the
installpath registry key as suggested in TID 2967507 and also followed
the
other suggestions. No luck. I also think I got the same error at some
point
after rolling back from 4.9 client to 4.83, without updating the
agent.
ZfDagent.msi will install fine on a clean machine that has not had the
previous version of the agent or client installed and policies will
work.

> interesting, someone else has reported this problem, but it looked like
> a terminal server issue.
I also found a few thread with this on the forum, but they were with
Win98 or 2k on the workstations, and we have XP, so the client is
different. Also, their problem was different, and the error message about
the missing entry point was just another one of their symptoms. My
problem is that the agent is not working on my XP workstations and I
cannot apply policies or register a workstation (which I can do with the
new wstations where we never had client 4.83 or the Zfd4 agent installed,
and also on our Win98 workstations).
> I'm still not clear on the exact sequence;
Ok, we had client 4.83 and Zfd4 installed. All was well re policies etc.
We updated to SP1b with Zfd, then we updated all our clients from 4.83 to
4.9. Then we deleted the InstallPath key in the registry, uninstalled the
Zfd4 agent and installed the .msi version tht comes with SP1b.
> If so, what options did you choose with client 4.9 during install?
The tech who did the client upgrade tells me that when she did a custom
install of 4.9 (with the old management agent present), she didn't get
the ZfD options in the client she used to get with 4.83. There was only
one box which was ticked and greyed out (i saw this too when I was
playing around). But I have since discovered, that when I took the
management agent off and then uninstalled 4.83 and installed 4.9, I had
all the ZfD options to tick I had with 4.83.
> Have
> you tried 4.9sp1a?
We did try it on a few machines, but found that a staff member who logs
in on lab machines as xxxxx.staff could not log in on the patched
clients. When we put the 'staff.' into the context field in the advanced
section of the login and only his username at the top, it worked! We
tried this on all the patched client machines and it happened on all of
them (I won't be upset if you don't believe me, it's too weird for
words!).
I'll try patching the client and see what happens when I update to
the .msi agent.
Thanks for your help, Shaun.
Renate
>

Could not find the entry point in the procedure sqlite3_wal_checkpoint sqlite3.dll dynamic link library., Could not find the entry point in the procedure sqlite3_wal_checkpoint sqlite3.dll dynamic link library.

Could not find the entry point in the procedure sqlite3_wal_checkpoint sqlite3.dll dynamic link library.

Could not find the entry point in the procedure sqlite3_wal_checkpoint sqlite3.dll dynamic link library.
Try uninstalling your MobileMe control panel for Windows.

The \System Root\System32\drivers\NatMotion.sys device could not locate the entry point IoSetDeviceInterfaceState in driver ntoskernal.exe

After installing version 5.1.1 of the Flexmotion driver, and installing f5 update, I got the following message after rebooting the system: The \System Root\System32\drivers\NatMotion.sys device could not locate the entry point IoSetDeviceInterfaceState in driver ntoskernal.exe. OS is Win NT. I see device in MAX , but can not initialise it, and cannot make firmware update.
I do not se device from NT system menager.

The instructions on the f5 update are not 100% explicit about what to do for NT. The NatMotion.sys file should not be replaced on NT systems, only on the specifically listed OSes. Uninstall and reinstall the 5.1.1 driver along with the f5 update, however only install the components that do not specifically mention a particular OS.
Regards,
Brent R.
Applications Engineer
National Instruments

How to get the entries in a jar/zip file contained within a jar/zip file?

If I want to list the jar/zip entries in a jar/zip file contained within a jar/zip file how can I do that?
In order to get to the entry enumeration I need a Zip/JarFile:
ZipFile zip = new ZipFile("C:/java_dev/Java_dl/java_jdk_commander_v36d.zip");
// Process the zip file. Close it when the block is exited.
try {
// Loop through the zip entries and print the name of each one.
for (Enumeration list =zip.entries(); list.hasMoreElements(); ) {
ZipEntry entry = (ZipEntry) list.nextElement();
System.out.println(entry.getName());
finally {
zip.close();
Zip file "java_jdk_commander_v36d.zip" contains two zip entries:
1) UsersGuide.zip
2) JDKcommander.exe
How to list the entries in "jar:file:/C:/java_dev/Java_dl/java_jdk_commander_v36d.zip!/UsersGuide.zip"?
The following code:
URL url = new URL("jar:file:/C:/java_dev/Java_dl/java_jdk_commander_v36d.zip!/UsersGuide.zip");
JarURLConnection jarConnection = (JarURLConnection)url.openConnection();
zipFile = (ZipFile)jarConnection.getJarFile();
would point to "jar:file:/C:/java_dev/Java_dl/java_jdk_commander_v36d.zip", which is no help at all and Class JarURLConnection does not have an enumeration method.
How can I do this?
Thanks.
Andre

I'm not sure I understand the problem. The difference between a zip and jar file is the manifest file; JarFile is extended from ZipFile and is able to read the manifest, other than that they are the same. Your code
for (Enumeration list =zip.entries(); list.hasMoreElements(); ) {
ZipEntry entry = (ZipEntry) list.nextElement();
System.out.println(entry.getName());
}is close to what I've use for a jar, below. Why not use the same approach? I don't understand what you're trying to do by using JarURLConnection - it's usually used to read the jar contents.
String jarName = "";
JarFile jar = null;
try
    jar = new JarFile(jarName);
catch (IOException ex)
    System.out.println("Unable to open jarfile" + jarName);
    ex.printStackTrace();
for ( Enumeration en = jar.entries() ; en.hasMoreElements() ;)
    System.out.println(en.nextElement());
}

How to add the entries and how to delete the entries from custom Z-table?

Hi Experts,
My requirement is I need to add the entries from program to three custom z-tables . Assume as zabc1,zabc2,zabc3.
Here how to add the entries from program to Z-table.???
And one more requirement is I want to provide a deletion checkbox in selection screen . Initial it was unchecked. If I am giving tick mark then the entries should be deleted from above custom Z-tables. this all will done in backgroung job?
Could you please guide me the logic how to crack this???
Let me know if you need more Info
Thanks
Sanju

Hi Sanjana,
What you can do is to use the ABAP keyword INSERT or MODIFY to add or modify records to a given database table. Here are the syntax taken from SAP documentation:
*Insert Statement
INSERT dbtab
Syntax
INSERT { {INTO target VALUES source }
| { target FROM source } }.
Effect
The INSERT statement inserts one or more rows specified in source in the database table specified in target. The two variants with INTO and VALUES or without INTO with FROM behave identically, with the exception that you cannot specify any internal tables in source after VALUES.
System Fields
The INSERT statement sets the values of the system fields sy-subrc and sy-dbcnt.
sy-subrc Meaning
0 At least one row was inserted.
4 At least one row could not be inserted, because the database table already contains a row with the same primary key or a unique secondary index.
The INSERT statement sets sy-dbcnt to the number of rows inserted.
Note
The inserted rows are finally included in the table in the next database commit. Up until this point, they can still be removed by a database rollback.
*Modify Statement
MODIFY dbtab
Syntax
MODIFY target FROM source.
Effect
The MODIFY statement inserts one or several lines specified in source in the database table specified in target, or overwrites existing lines.
System fields
The MODIFY statement sets the values of the sy-subrc and sy-dbcnt system fields.
sy-subrc Meaning
0 At least one line is inserted or changed.
4 At least one line could not be processed since there is already a line with the same unique name secondary index in the database table.
The MODIFY statement sets sy-dbcnt to the number of processed lines.
Note
The changes are transferred finally to the database table with the next database commit. Up to that point, they can be reversed using a database rollback.
Hope it helps...
P.S. Please award points if it helps...

How to delete the entries from the transport request

i need to delete the entries programatically from the transport request for all the entries which is exists in the package for the tables e070 and e071.

Hi,
I think you need to have authorization for that thru auth group SA.
One more thing is where ever its created like source client only you can do if u have authorization.
Regds
Sivaparvathi
Please reward points if helpful...

Dump while copying the entries in view cluster

Hi Experts,
I am having a scenario where i am getting the dump while copying the entries through the vies cluster.
I have 2 tables CU00 and CU01. CU01 is depended on CU00.
CU00- it is having schema which are defined by the user.(SCHEMA-P,DESC)
CU01- this table is having the different tabs in a tab strip for a each of the user defined schema.(SCHEMA-P,SEQNO-P,TABID)
the data will be as follows
In CU00
          SCHEMA1         first schema
          SCHEMA2         second schema
In CU01
          SCHEMA1         01              TAB1
          SCHEMA1         02              TAB2
          SCHEMA2         01              TAB2
          SCHEMA2         02              TAB3
I maintained above 2 tables in a view cluster by making CU00 is the start point and defined the field dependencies as well.
in the T-code SE54 i tried to copy the existing schema and all its dependencies(means all the dependent entries in the CU01 table also).
when i pressed the SAVE button it is going for the dump by saying due to duplicate entries in the table CU01.
but it should check the consistency and display the error message when i pressed the COPY key.
I am badly struck up here. Please help me on this issue.
thanks in advance.

Hi Gouri,
CU01 and CU00 both are dictionary tables.
What I think is, while copying all the dependencies for a particular schema the system ha to check whether the data can be inserted into the child tables or not. I too dont know whether this can be done or not.
If not, it should display an error message stating that " primary key violation occurs please use different key values..."
thanks for the reply.

Table Maintance - Not able to see all the entrie of table

Hi All,
I have created a Z table where I have mentioned 3 key fields.
MANDT      CLNT    3
ANSVH      CHAR   2
ENDDA      DATS    8
Now when I create the multiple entry using sm30 with the key field ANSVH same and different date i amnot able to see the entry in the sm30 but in table it exists.
e.g.
in table i have 2 entrries
100   A     30.03.2009
100   A     31.03.2009
but in sm 30 i am able to see only one entry
A     30.03.2009
I have generated the table Maintainnance several times but no success.
pls help.
Regards,
Umesh Chaudhari.

Hi Siddharth Chordia,
Thanks for your all effort.
but ti have checked the points mentioned by you here.
1) you might have forgotten to check key field for date field,
              All the three fields mentioned are key fields.
MANDT     MANDT     CLNT     3     0     Client                                    KEY Initial
ANSVH     ANSVH     CHAR     2     0     Work Contract                       KEY Initial
ENDDA     ENDDA     DATS     8     0     End Date                              KEY Initial
BEGDA     BEGDA     DATS     8     0     Start Date
BETRG     BETRG     CURR     9     2     Amount
PERCT     PERCT     DEC     5     2     Percentage
ZPDPF     ZPDPF     DEC     7     3     DPF Department Production Factor
2) may be the table is inactive, if so activate the table
       Table is active.
3) may be you would have made the date field as a key field after you had created the table, in this case you will have to click on utilities menu -> database utility, then click on activate and adjust database,
Even though I created all the key fields in first place it self, I tried data base utility also.
4) once you give the entries you might have forgotten to save the entries.
Entries in the table
100   A     31.03.2009 01.01.2009     5,000.00   0.12     0.123
100   A     30.06.2009 01.01.2009     5,000.00   0.12     0.230
Entries in the SM30
A     30.06.2009     01.01.2009     5,000.00     0.12     0.230
I even tried to create the new table. but the same result.
Regards,
Umesh Chaudhari

Easing the entry of 2 point interpolat​ions into scaling module.

Similar Messages

Maybe you are looking for

Easing the entry of 2 point interpolations into scaling module.