Echo in audio! Need help!!

Hello, I am using Audition for audio recording and its going great except for one thing, there is a little echo, little but very noticeable, in my audio. I was wondering if there was a way to remove the echo or prevent the echo. I could really use the help.

This might be happening because you have enabled record monitoring in the Windows Recording Mixer. Right-click on the speaker icon on the taskbar, then select 'Recording devices'. Double-click the recording device icon you want to use, then select the 'Listen' tab. Make sure that the check box 'Listen to this device' is clear. I've been caught out by this ...... too many times!
Pete.

Similar Messages

DVD Audio Need Help

Help Please,
I'll just cut to the chase... I do not get audio off my dvd's. I get the video and can watch them but without any sound. I have the Diamond Plus board and am just running the Audigy. I downloaded all firmware for dvd drives, have one with digital enabled and one without (neither work), its not a muting/volume issue... Have been searching forums of MSI and Audigy have seen a few similar problems but never have been able to find answer to them. Looked at Plextor's (the manufacturer of both dvd -+r/rw) help site, very lacking area to be honest. Please give thoughts/ideas as they would be greatly appreciated... Im out of them
Thanks for your time

i just installed the dvd decoder off my old nvidia graphics card driver cd. works wonders baby. thank you guys all for your help... i love you all... i would still be lost without your help... its been a while since ive had to deal with the initial setup of a home built 'puter. the most impressive piece of my gear in my opinion so far has been the mobo... cant wait until i get my place cleaned up and can install this zalman water cooler. mmm mmm good... then the overclocking begins....
Thank You all again... much appreciated

No output sound from output port/analog audio: Need help

hello, I want to connect my analog audio equipment to my iMac. I have done this in the past with my old G3. I have connected the RCA cables to a 3.5 mm jack and put it into the audio input port, which was what worked on the G3. When I open the sound page for input & output, on Output I can see the volume bar thing moving in relation to the sounds from mic, turntable, etc: all the analog audio things. However, there is no actual output of sound through the iMac;s speakers or a headphone. The output page is pretty simple so I am real sure I have all the rigt things checked, unchecked etc. Any ideas? Thanks.

I had what sounds like a similar problem to jazzzrat. i had my macbook setup to a stereo and it worked for over a year. suddenly no sound came out of the stereo. in my case, it definitely was a software setup thing.
plug in your stereo jack into the audio out port. then go to system preferences-->sound-->output. on there you should see, under "device for sound output": Name=Headphones, port=built-in output. (if you see name=built in speakers, you plugged in the wrong plug). Now go down to the bottom of the window and UNcheck the "mute" box, and make sure the volume slider is midway or more.
For some reason, mac allows you to mute the "headphones" and "built in speakers" selectively. we have no idea how that box got checked, that remains a complete mystery. but when we eventually found -- and unchecked -- the box, our stereo output came back just fine.
i hope this works for you. good luck and have a good new year.

Need help getting audio off of a dvd...

[You can skip this paragraph if you don't need the backstory.]
So, for several weeks I've been trying to get some audio off of a DVD of mine and into a simple mp3 file. A couple days ago I found and followed this guide, and thought I had succeeded. But after a while I realized that the file I got does not play nice with my handheld mp3 player, or mpd, or mplayer, or anything whatsoever that is not gstreamer-based. MPD goes especially berserk - after playing the file, it can no longer play anything else until I reboot (yes reboot - restarting mpd doesn't fix anything). I should also mention that I'm aware that the guide is not 100% correct; I followed the advice and corrections of some commentors there too.
Anyways, I guess I need to ask for help with this. How would you go about getting audio off of a DVD?
Last edited by fflarex (2008-07-19 01:26:01)

I usually use the following command to rip a music dvd to wav:
OUTPUTDIR="/Some/Rip/Dir"
TITLE=2
FIRST_CHAPTER=1
LAST_CHAPTER=13
CHAPTER=$FIRST_CHAPTER
AUDIO_ID=128
echo "Ripping Audio..."
while [ $CHAPTER -le $LAST_CHAPTER ]; do
let NO=$CHAPTER
mplayer -dvd-device /dev/dvd1 dvd://$TITLE -vo null -vc null -ao pcm:waveheader:file=$OUTPUTDIR/track$NO.wav -af lavcresample=44100 -aid $AUDIO_ID -chapter $CHAPTER-$CHAPTER
let CHAPTER=CHAPTER+1
done
Resampling to 44100 is important since most mp3 players cannot handle 48000.
Then I have another little script that converts it to flac, sets the correct tags, and finally converts the flac to oggs as well..
Last edited by GogglesGuy (2008-07-19 01:45:06)

Need help to open audios attached in a PDF file

Hello
I just need help. I have ordered a reviewer online that has audios and texts in a pdf file. I was told to download the latest adobe reader on my computer. I have done the same thing on my ipad mini. I am not so technical with regards to these things. Therefore I need help. I can access the audios on my computer but not on my ipad.
I want to listen to audios with scripts or texts on them so i can listen to them when i am on the go. I was also informed that these files should work in any device. How come the audios doesnt work on my ipad.
Please help me on what to do.
Thanks

Audio and video are not currently support on Adobe Reader. :-<
You need to buy a PDF reader that supports them. My suggestion is PDF Expert from Readdle ($US 9.99)

Need help.. premiere pro cs4 imports video but not the audio!!

i need help before i fkn suicide..
i'm trying to import a .mpg clip its importing it but with out the audio.
the file is fine when i play it in VLC or WMP
i've also imported it before and it imported fine.. video and audio but now i dunno what the fk is goin on!?!?!?!?
i've tried uninstalling cs4 then reinstalling etc... i've tried the 4.0.1 update etc... i've opened it up in another program then changed it into .avi and still nothing!!!!
it must be something i'm overlooking in settings
HEEEEEEEEEEEELP!!!!

try doing a little research on the hundreds of posts exactly like yours.
Its called the ac3dc3dbs2t32cfgh24.dll codec or something, its in encore and you copy it into premiere. I dont know, ask someone who does.

Need help!! Compaq V3500 No audio driver available in website

Need Help Compaq V3510TU P/N GG201PA#AKL Windows XP Professional 32 bit, After I re installed the new OS..
The windows doesn't have the audio driver. I tried everything download many of Conexant HD many many version...
they don't work at all.
Please tell me what you should do next
P.S. Last year I came to hp website, it provided many driver in windows xp but now nothing... where 'd they gone???
I tried these, but didn't work
sp36509
sp35682
and many many of them
This question was solved.
View Solution.

Hi:
Please read the XP downgrade guide at the link below:
http://h30434.www3.hp.com/t5/Notebook-Operating-systems-and/General-XP-Downgrade-Guide-for-HP-Laptop...
The instructions for installing the audio for your model can be found under the section labeled 1. Easy Models
More than likely you didn't install the required MS UAA driver before installing your audio driver.
You will need to uninstall any audio drivers you tried before installing the MS UAA driver.
Paul

Need help dealing with nested audio in Premiere Pro CC 7.2.2

Hi, so previously I have been working with nested multicam video and nested audio together (one video track, and one audio track).
However, I am hitting some issues with the nested audio workflow, and am hoping someone could help me iron out my issues.
1. Once I've completed my edit, how do I efficiently flatten my nested edits so I have all of my original audio back? (For mixing purposes)
2. Audio nesting sometimes seems glitchy. When making new nests, sometimes I will only get the topmost audio track in my nest, and I'm not sure what's causing that to happen.
I REALLY need helping getting my workflow together, as it's at a bit of a stand still right now. I think I'm going to switch to unnested audio to avoid issues, but still need to flatten my existing edits to do that as well.
Many thanks!

This bug is NOT FULLY FIXED. I'm on a tight deadline so i'm not looking very hard online to see if i'm alone - so please forgive me for just posting here...
I'm using CC7.2.1 it's 1/21... very grateful that match frame FINALLY works on merged clips, but, again, this insert/overwrite bug is only PARTIALLY FIXED.
Insert/overwrite with merged clips on 3-point edit now works, but ONLY when cutting in BOTH merged video+audio... if you're just trying to cut in the audio from a merged clip using a 3-point/4-point edit via hotkey, it's a no-go.
I, for example, needed to re-cut in audio under some video with effects on it. So, I unpatched the video source completely and patched source audio tracks 1-4 to the appropriate sequence tracks. Upon hitting insert or overwrite multiple times, nothing responds. The only way to cut anything in from the source (merged clip) was to patch the source video back into the timeline on an unused video track, then cut ALL the tracks from the source in, I then had to delete the video track re-link the now free audio to the original video. Not a big deal, but annoying enough & waste of precious time on tight deadline.
So, yeah, I have a workaround but is still not appropriate to have a core function not work properly. Especially when I'm working with a very complicated timeline.
That said, thanks for keeping on top of our gripes, Mark.

Need help regarding 5.1 audio on sblive va

dear users,
i m tight on budget thats y cant afford the audigy series or any new hifi cards.. i need help in activating 5. audio on my sbli've value card though old but i always love it.. theres a feature li've surround and when i activate it my surround mixer shows fi've speakers and sound comes from 4 speakers i wonder how can i connect the 5th speaker.. 2ndly there r two analog outputs on the card which connects front two and rear two speakers theres another spdif output now is that to connect 5th speaker? also plz guide me about the spdif cable which will connect with sbli've value cards and how can i get its output from ? i m really amauter in this stuff plz guide and help me thanks
regards
muddassar

Muddassar,
The SB Li've Value is only a 4/4. speaker system card and that does not support a 5. speaker as you would not have the available jack for such connection.
Jason

Need help, No audio for mpeg on Quicktime

Ok, the other day i downloaded a third party movie player that played movies that quicktime wouldnt play. It was MplayerOSXB8r5 and it worked ok. When i tried to play my regular mpegs that worked fine with quicktime i got no audio. the avi files work just fine, its only my mpeg movies that wont play with audio.
So i trashed the Mplayer hoping the problem would be fixed & nothing. I downloaded quicktime pro & nothing. I need help in fixing this problem.
any suggestions

Flip replies:
We have recently become aware of an audio compatibility issue revolving around Flip Video and the latest QuickTime 7.4.5 update running on the Mac OS X 10.4 Tiger operating system. Apple is aware of the issue and is investigating it with Flip Video.
This issue does not affect customers running the Mac OS X 10.5 Leopard operating system.
Several customers have reported that they have had success using the QuickTime components available from Perian (http://perian.org). Please note that we cannot officially recommend this as we have not fully tested the application, nor do we have knowledge of what other applications may be affected.
We apologize for any inconvenience this may have caused. Please do not hesitate to contact us for further assistance.
Thank you,
PS: Perian does me no good. A friend with 10.5 says he has no problem, just as indicated above.

TS1717 This article is vague and unhelpful. My iTunes needs help from a pro. I have over 120,000 songs -- NO movies, TV, radio, or books... I have other programs which efficiently run things which are not audio-based. So why can I not get iTunes working w

This article is vague and unhelpful. My iTunes needs help from a pro.
I have over 120,000 songs -- NO movies, TV, radio, or books...
I have other programs which efficiently run things which are not audio-based.
So why can I not get iTunes working well?? It now takes at least 10 secs for any operation to be completed!
That is just plain evil. But I am sure I could do something to help.
All the music is on an 2T external drive.

TS1717 as noted in the thread title...
Brigancook, is the library database on the external or just the media? iTunes reevaluates smart playlists and rewrites its database after every action on the library. I've found this can make a library half that size, with a lot of smart playlists, quite sluggish. That said I'm aware part of my problem is aging hardware. Having the database on the internal drive may improve performance if it is currently on the external.
I'd expect to see an exponential relationship between size and response time which may explain what you see. Cutting down on the number of smart playlists might help. If we're really lucky the long awaited iTunes 11 might have streamlined some of the background processes as well as cleaning up the front end.
tt2

Audio acting up in Premiere Pro | Need Help ASAP

Okay, I need help ASAP because this has been a serious issue for me.
So my source video (an interview) is on PR's timeline. I start playing it and it's working fine, but all of a sudden, the audio skips back to the beginning of the interview, then about 10 seconds later, it gets back on track. I checked the original video that I imported it from and it's all fine. I even reimported the file, but the problem persists.

Okay, problem solved. I took the working source video, took the audio out and put it in there.

I have a Steinberg MI4 and a Roland Fantom X7, and am trying to use my Fantom in Logic to record audio. Need help setting it all up using MIDI cables. Please help !

I have a Steinberg MI4 and a Roland Fantom X7, and am trying to use my Fantom in Logic to record audio. Need help setting it all up using MIDI cables. Please help !

Encryption wouldn't matter except for Wifi.
While 10.2 might help, there's not much you can do on the Internet these days with less than 10.4.11
Tiger Requirements...
To use Mac OS X 10.4 Tiger, your Macintosh needs:
    * A PowerPC G3, G4, or G5 processor
    * Built-in FireWire
    * At least 256 MB of RAM (I recommend 1GB minimum)
    * DVD drive (DVD-ROM), Combo (CD-RW/DVD-ROM) or SuperDrive (DVD-R) for installation
    * At least 3 GB of free disk space; 4 GB if you install the XCode 2 Developer Tools (I recommend 20GB minimum)
http://support.apple.com/kb/HT1514
http://www.ebay.com/sch/i.html?_nkw=mac+os+x+tiger+retail+10.4
See Tom's, (Texas Mac Man), great info on where/how to find/get Tiger...
https://discussions.apple.com/message/15305521#15305521
Or Ali Brown's great info on where/how to find/get Tiger...
http://discussions.apple.com/thread.jspa?messageID=10381710#10381710
As far as Memory, that's sort of easy, find your eMac here...
http://eshop.macsales.com/MyOWC/Models.cfm?Family=emac&sType=Memory
As far as Hard Drive, it's not easy to replace the Internal drive, I'd maybe suggest an external Firewire drive to boot from...
http://eshop.macsales.com/item/Other%20World%20Computing/MAU4S7500G16/

Need help finding a audio system ( stressed)

I have cd with over 100 songs , and I need help finding a boombox that will play the CD anyone have any idea, I got no help from the store.

here are the specifications for Philips eXpanium eXp 2461 , if somone can help me find a boomboox with simular specifications it would very helpful
Philips eXpanium eXp 2461 - CD / MP3 player
CD System
CD system type CD / MP3 player
Media load type Top-load
Playback modes Repeat all,
Resume play,
One track repeat
CD system response bandwidth -19980.0 Hz
Signal-to-noise ratio 85.0 dB
CD shockproof memory 45 seconds
MP3 shockproof memory 100 seconds
CD-R compatible Yes
CD-RW compatible Yes
CD track programming Yes (50 tracks)
Digital audio standards supported MP3
Supported bit rate 32 - 320Kbps
General
Product type CD / MP3 player
Weight 8.0 oz
Carrying Case
Case type None
Built-in Display
Audio system built-in display LCD
Audio Features
Sound effects Digital Dynamic Bass Boost (Digital DBB)
Sound output mode Stereo
Additional features

I need help fast please an't render my full audio equalizer from adobe after effect

I need help really fast i can't render my full audio equalizer from adobe after effect

Without knowing any details about your comp or render settings, this is going nowhere. This could be anything from Quicktime acting up to having set the work area.... We don't even know what version of AE you use on what OS.
Mylenium

Need Help! No Video Just Audio With .AVI Files

i got quicktime for my iPod, just only for that cause i think that quicktime really *****... i searched this whole site for an answer. i found something i thought would solve my problems with .avi files but my .avi files are mpeg-4 layered, and there's only a descent answer for indeo files? or something like that. i really need help cause i want to convert an ordinary .avi file to iPod extension... please please help!!!!!!!!!!!!

There is no single codec for movies that have .avi extensions. AVI is a container format, not a specific type of file. An AVI movie may use one of the Indeo codecs or one of the various flavors of DivX, among other possibilities. You'll have to find out what codec was used for the movies you want to view to determine what you need. Note that not all codecs for the various .avi movies are available for QuickTime.
If you want to try "hit and miss", you can try the codecs at http://www.divx.com/ and http://www.3ivx.com/ and see if one of them will work for you

Echo in audio! Need help!!

Similar Messages

Maybe you are looking for