Eclipse SLI cannot post

Well hello to the forum, I have been using MSI products for almost a decade, and I am facing a very difficult problem, that it drives me mad.
First of all I have the following system running for 3 and half years
Mobo Eclipse SLI bios v1.15 (1.F 03/03/2011)
CPU i7 920 2.66GHZ overclocked to 3.20GHZ
PSU TAGAN BZ-series 1300watt
Graphics MSI Cyclone HD 4890
RAM CORSAIR TR3X6G1600C7D, CMT12GX3M3A2000C9
HDD 2X1TB WD BLACK SATA3 RAID0, 2X1TB WD GREEN SATA2 RAID0
DVDRW LG SATA, DVD LG IDE
Sound MSI Creative XFi (came with mobo)
Screen ASUS VK246 on HDMI
Case Thermaltake Speedo full tower
A couple weeks ago when listening to internet radio, the PC freezed, no display, no reset button so I power it off.
I tried to power it on but the power indicator didn't have no light, the reset button had its light on and all other components had power, but no post.
I power it off, and let it go for the night. Next day I cleared the cmos, pulled out the battery, bought a new one cause the voltage was 2.9v, disassembled everything, put new thermal paste for the cpu, and posted after 4 or 5 loops, I got the system running installed windows 7 sp1, and let it run over night. Next morning the same thing happened , and it keeps happening if I leave the pc running at night.
I have checked everything, with one ram installed, disassembled graphics card, applied thermal paste to the gpu.
So I am out of ideas. I have endless loops for post and if I am lucky it will post!!
Is the mobo bios defected or is there a way to save it? I think it is some kind of capacitor that is going bad.
Any help would be nice.......................

xmad, thank you for your reply, I managed to post and boot my pc, but there is another issue that I came onto it.
My eclipse has the D-Led2 accessory that I never used it, so I hook it up to give it a try, but it is not working, the button has power, the lcd display shows nothing, and the funny thing is that it blocks my graphics card of displaying anything on the screen, I do hear the hard drives spin and everything else seems to work ok.
Is there any beta bios for eclipse sli, so I can test it?

Similar Messages

MSI Eclipse SLI - no POST

I had the system of my sig running fine for about 9 months (apart from a d-led2 stuck at CPU Init). The board was won in a MSI contest and I was thrilled with it. Bios was upgraded to 1.C I think following the guide in this thread with the forum tool 3 months ago and all was fine and dandy until 5 days ago.
I decided to take apart the system and rebuilt i for some case modifications and cable management. Re-assembled the system, being very careful as always and tried to boot up.
System started, leds on but never heard the single beep. 15 seconds later, auto shut down and reboot.
System disassembled, put on cardbox, cpu only, cooler, 1 stick of RAM @ bank A0 and GPU. Cleared CMOS by removing PSU cable, pulling battery and hitting clear CMOS button for 5 sec as per manual instructions. Reboot @ 15 seconds no beeps
Changed RAM module with one known working (from other system) and at comparability sheet from MSI (KVR1066D3N7 1GB). Same thing
Changed GPU with one known working. Reboot again @ 15 seconds
Changed PSU with one from the other system. Nothing
Borrowed a CPU from a friend (don't have a spare one sitting :p). Reboot again
Anyone have a suggestion? Cause I am out and I think the only thing that's left is a bad m/b and I don't know what is MSI policy for competition prizes

Quote from: HU16E on 25-February-11, 04:13:58
Would think it falls under a policy similar to having received a product as a gift. If you have a prize award receipt or documentation of any kind, I would think MSI or your distributor/reseller could help you with an RMA process.
I have the email from the EU Technical PR Officer, Cyril I think, for my address to send the prize, but nothing else. I have opened a ticket with online support and we shall see.
Thanks for the answer though

New ECLIPSE SLI Build, but not POSTing

Hello MSI peeps,
Installed MB, CPU, CPU cooler, 1 stick of RAM, SSD, HD, PSU, 1 Video card and Optical drives, but cannot get it to POST.
I powered up and the MB is showing light blue indicators on installed components, but no video signal going to monitor.
I shut down, then connected DLED2 and powred up and DLED2 says CPU.ini, which means CPU error on POST, but is this really true? I have read allot of everyone's posts on this forum where all claim that DLED2 is faulty.
I am thinking that I may have plugged in too many drives and will disconnect the HD and optical drives to see if that may be the problem....should I also try to reset CMOS too?
Here's my rig....
Case: Coolermaster CM-830
Mainboard: MSI Eclipse SLI
CPU: Intel i7 975
CPU cooler: Thermalright ULTRA-120 Extreme
RAM: Two sets (12GB) of Corsair TR3X6G1600C7D Dominator 6GB PC3-12800 1600 MHz (2GB * 3)
Video Cards: EVGA Model GTX295 Co-op x 2
PSU: Enermax Model EGX1250EWT GALAXY EVO 1250W
Primary drive: Patriot Torqx 2.5-Inch 128 GB SATAII SSD - Model PFZ128GS25SSDR
Storage drive: Seagate Barracuda 500gb
Optical drives: Pioneer Blu-Ray DVD Burner Model BDR-203BKS / SAMSUNG DVD Burner Model SH-S223L
Thanks for your inputs!!!

Hey All,
Thanks for the help, but still no change....to save you having to read every thread, basically my build won't go to post.
DLED2 reads that it is CPU.ini and of course I questioned hte validity of the DLED2 reading as I have read other threads claiming that DLED2 is faulty.....so thanks to those who have replied, I have tried everything suggested, but the build still won't post....no beeps, no video signal, but the mobo and video card LEDs indicate no issue.
Is it RMA time or should I try something else? Should I just RMA the board or should I also RMA the CPU too?
Thanks for your help!
My build....
Case: Coolermaster CM-830
Mainboard: MSI Eclipse SLI
CPU: Intel i7 975
CPU cooler: Thermalright ULTRA-120 Extreme
RAM: Two sets (12GB) of Corsair TR3X6G1600C7D Dominator 6GB PC3-12800 1600 MHz (2GB * 3)
Video Cards: EVGA Model GTX295 Co-op x 2
PSU: Enermax Model EGX1250EWT GALAXY EVO 1250W
Primary drive: Patriot Torqx 2.5-Inch 128 GB SATAII SSD - Model PFZ128GS25SSDR
Storage drive: Seagate Barracuda 500gb
Optical drives: Pioneer Blu-Ray DVD Burner Model BDR-203BKS / SAMSUNG DVD Burner Model SH-S223L

Random restarts with Eclipse SLI board

This is a copy from my post on the Vista forums havent gotten much help there.
Describe the problem in detail!
I just built a new system on December 22nd 2008. I do Tier 2 and 3 Helpdesk work so I can work my way around a system. I put the machine together installed Vista did all the updates got all the newest drivers. Basically since I have built the Machine it will just randomly restart. It will not display a BSOD, I have auto restart turned off, and it does not create an event in the event viewer. It is almost like someone touched the reset button.
When did the problem start?
December 22nd 2008 the day I built the machine.
What have you tried to fix it?
Tried several different BIOS setups. I have upgraed the bios, did all the windows updates, got all the newest drivers for video, audio, lan etc etc. Removed MSI Live Monitor, disabled green power in Bios, and removed overclocking center. Went through event viewer and corrected three of the four errors that was showing up. One error is the Kerebos one and I am not worried about that one. I have just run both Memtest86 and Memtest86+ and both of them stop responding about half way through the test.
What is the error message (of any)?
I have Vista set to not auto restart so I should see a BSOD but I get no message. I have had 4 restarts just today and none of them created a new MEMORY.DMP file or any type of event in the viewer.
I do get warnings about something called FLASH.SYS but I cannot seem to track down what this is.
What was the last thing you did before the problem started?
Built the machine.
What are your system specs?
Vista 64
MSI Eclipse SLI X58
12 Gigs Crucial ram matched to the MoBo using the crucial matching system on the crucial website. The MoBo supports up to 24 and I am using Vista 64bit.
Antec P190 Case (Dual power supplies for a total of 1.2 KW of power)
Intel Core I7 2.66
Creative Extreme Gamer Edition PCI E sound card
Mcaffee
BFG 260 GTX
Coolmaster V8 cooler (CPU under stress runs about 70f well below the max of 208f)
Do you have a screenshot?
Nope
My next step is to take out 6 gigs of RAM and see if the issue goes away.
Any suggestions?

Quote
12 Gigs Crucial ram matched to the MoBo using the crucial matching system on the crucial website.
Please provide a link to the Crucial Product site for your memory modules and make a screenshot of the CPU-Z "SPD" view.
Quote
My next step is to take out 6 gigs of RAM and see if the issue goes away.
Test one memory module only and see what happens. If things seem fine, add one more module and test again (and so on).

What I hate about the Eclipse SLi

Not sure where to post this kind of thing, but having spent a fortune (£3,500 to be exact) on my new build PC, I thought I'd make a quick list of why I regret buying the MSI Eclipse SLi MB rather than another manufacturer. Maybe someone from MSI will read this and slap their designers about a bit
1) It has 10 SATA ports and supports SLi. What they don't tell you is that if you have 2 GFX cards, you cannot use 2 of the SATA ports as the 2nd GFX card covers them up. I had to purchase an additional PCI-E SATA card, and now, obviously, 2 of my planned devices don't work until Windows has booted and the drivers are loaded.
2) If you have a 2nd GFX card, it covers up the DLED and you cannot read the POST messages.
3) Needing to use a piece of tape to fix the thermocouple to some component
4) Less than great documentation on the BIOS options
5) Having only 2 USB headers on the MB. With everything being USB these days, more headers would be good so I can connect up my multi-card reader as well as case-mounted USB ports.
6) Poorly performing RAID implementation (or poor drivers) for RAID5
Anyway, that's my rant over for now. I've always used MSI MB's (except my last one was an Abit), but this has really put me off buying another one. I really regret it.

Quote from: Surreal-Killer on 05-January-09, 21:28:55
Not sure where to post this kind of thing, but having spent a fortune (£3,500 to be exact) on my new build PC, I thought I'd make a quick list of why I regret buying the MSI Eclipse SLi MB rather than another manufacturer. Maybe someone from MSI will read this and slap their designers about a bit
1) It has 10 SATA ports and supports SLi. What they don't tell you is that if you have 2 GFX cards, you cannot use 2 of the SATA ports as the 2nd GFX card covers them up. I had to purchase an additional PCI-E SATA card, and now, obviously, 2 of my planned devices don't work until Windows has booted and the drivers are loaded.
2) If you have a 2nd GFX card, it covers up the DLED and you cannot read the POST messages.
3) Needing to use a piece of tape to fix the thermocouple to some component
4) Less than great documentation on the BIOS options
5) Having only 2 USB headers on the MB. With everything being USB these days, more headers would be good so I can connect up my multi-card reader as well as case-mounted USB ports.
6) Poorly performing RAID implementation (or poor drivers) for RAID5
Anyway, that's my rant over for now. I've always used MSI MB's (except my last one was an Abit), but this has really put me off buying another one. I really regret it.
1.) I solved the SATA issue by connecting the sata cables to the ports BEFORE i put the cards in. Mine work fine.
2.) What GFX card are you using? I have 2 x GTX285's and they are NOT small. Yet I can still see my DLED. Perhaps if you squat down to eye level vs. Looking from the top of the board down?
3.) Not sure what you are talking about. I know my Copper heat pipe was missing a plastic retention clip and spring/ Found it packaged UNDER THE BOARD (damn QA dropped the ball). Clip was broken so I had to pay $5 for shipping or a new plastic clip for mine.
4.) I agree they need to document the BIOS much better.
5.) To be fair, most ALL the major sellers like Newegg and Tigerdirect list how many stat headders, usb headders etc there are. Not knowing there were only 2 herders is the fault of the buyer.
6.) On board raid is always cheap bro. Good raid cards can cost around $200-1000USD. Hardware > Software. I bought a mid line SATA Raid card for my box. Have 3 raptor drives in Raid 0. VERY happy i did it to.

Eclipse Sli - Not going to BIOS

Hi there
I was hoping that someone out there could help me! I have just finished building a new machine and decided to go the MSI route as opposed to the ASUS route (regretting that already!) Anyway, having finally managing to get past the machine not booting at all I have got to a stage where I cannot get into the BIOS and get no further than the memory check. The spec is the following:
Eclipse Sli
Intel Core i7 920
3GB OCZ Gold Series Triple Channel
Leadtek 7800 GT TDH PCi Express
Soundblaster Fatal1ty PCI
Hiper Type R II PSU
I have disconnected the Soundblaster and all the memory seems to be recognised because thats as far as I get - confirmation that there is 3GB on board. Is there anything else that I am missing or should be doing?
Any help would be greatly appreciated!
Thanks

Thanks to all who have posted on this thread with help and advice.
New motherboard came on Monday evening. Built on Tuesday evening, switched on with eyes closed and.................EUREKA!!! We have lift off!! Manged to get into BIOS and select the DVD drive etc. I went for XP Pro x64 for the moment and it has installed flawlessly. Only problem I am getting at the moment is trying to find the drivers for the SM Bus as I am getting the yellow triangle on device manager. Don't suppose anybody has any ideas, there doesn't seem to be anything on the driver disk.
Should I upgrade the BIOS? Are there any marked improvements over the pre installed (can't tell you version at moment as I at work!) If I do whats the best way of doing it. Is the Live Update thing still a recipe for disaster??
How's yours getting on bdhuf?

PC shuts down or reboots spontaneously (MSI Eclipse SLI)

Starting a new thread to avoid totally hijacking another thread talking about almost the same symptoms here.
My original post:
Quote from: Smoke on 05-April-09, 12:43:21
I get this same situation.. except the event viewer doesnt state anything.
The system is not bluescreening.. it just hardware powers down and reboots.
I get the same message as the original poster as well, it is very annoying as it often happens in the middle of doing something.
I wonder if it could be thermal related to the high IOH temps on the board (often 80-85C, but not sure what happens to them in the middle of playing a game)? Is there any way to log the temperatures to a file so I can check what they were at the time of the crash?
I get this issue whether I change the default bios settings or not. Ive got a 920 on my eclipse board, my CPU temps are below 30C under load. System temp is about 27C.
What can I do?
The following replies:
Quote from: AaronYuri on 05-April-09, 12:56:57
That's way too high, even for 100% load. Reinstall the heatsink.
Quote from: Smoke on 05-April-09, 20:46:53
It is? I found another thread on this forum where it was mentioned that intel and msi said the IOH runs hot and to expect temps up to 100C. How do I go about changing the manufacturers heatsink on a board? Ive never done that before and cant find any procedural help thru google...
Ive been able to replicate the issue by running ram up to high usage. When I get above 98% ram allocation, I spontaneously reboot. So It could be a ram issue as well. Of would that be something possible IOH related as well?
Quote from: NovJoe on 05-April-09, 23:37:33
smoke,
Can you list out your full system spec and PSU spec?
System Spec:
Core i7 920 w/ TRUE 120
MSI eclipse SLI (bios 1.4)
6x 1gb corsair 1866mhz rated ram sticks (TR3X3G1866C9DF)
1500w thermaltake psu
galaxy gtx295 in the primary x16 pci-e slot
MSI eclipse soundcard in the 1st pci-e x1 slot
4x 1tb samsung 'UJ' hdd (raid 5)
O/S (= old winxp 32 bit until I get hold of a 64 bit os) running on 128gb PQI SSD
lg bluray burner
All the drives are sata2 and running on the ICHIOR ports.
For bios settings Ive got the optimised defaults with spread spectrum off and turbo boost on. Once its table then I will OC, but for now its not stable at the baseline yet.
Temp info:
IOH temps are as I said, around 80 at startup but rise to at least 87 under load, but not really much further that Ive seen.
CPU temps are very low with the dual-fan TRUE 120 heatsink. I havet seen it go above 35C with a reasonably heavy processing load. Usually sits about 0-2C above ambient at most when idle.
System temps get to about 40 under load, or around 27-35 under regular usage, but Im not quite sure what thats measuring the temp of on the board.
The issue is very frustrating but somewhat intermittent - I can go two days without a crash but then get several in a row. I wasnt previously paying attention to my usage at the time tho so I dont remember what I was doing when it crashed that I wasnt doing when it was fine. I have been able to replicate the crash/reboot/shutdown symptom by running multiple memory intensive apps and loading the ram up to just on the 2.99gb mark (the most winxp 32 bit will 'see') and it goes down. No blue screen though.. its a hardware issue not software I am pretty sure.
[edit] Updated the ram part number to be correct.

ok, should I label this possibly as solved?
I followed MSI's advice and checked through on drivers. Ive got totally up to date drivers, but nvidia just put out a .5 driver update (i mean, its increased the driver version by .50) and so I updated to that. I still got a sft reboot on testing, so no real joy.
THEN, I did the big change MSI asked me to do - Ive successfully brought my system up to bios 1.5B3 and pow, massive improvements all round!
Intelburntest runs perfectly now, no crash, no reboot, no errors of any kind. All residuals match. No memory errors. Memtest86 2.11 runs smooth as silk without errors either. PCmark runs out a basic benchmark of almost 19000 (about 3000, or 18.75%, more than the std core i7 920 benchmark without OC'ing) and looks great. Couldnt get that to run previously either.
The previous methods which 100% of the time would replicate the soft reboot of the system now no longer do so at all (i.e. 0% of the time yet) and for that matter I have not been able to get the box to fall over AT ALL since the new bios.
I have the same temps on cpu/ioh/system as I did previously. I recall for the same clock speed the cpu was putting out something well under 20 gigaflops... now its a solid 28. I didnt even realise that was a symptom of anything wrong, else the bios does some amazing extras.
I should note, Im only now using the 'optimised defaults' setting thru the bios. No overclock at all yet.
I'd love to know what MSI changed from 1.4 to 1.5B3, but whatever it was.. it does appear to have solved my issues. I wont say that conclusively just yet, but I cant bring the system to a crash no matter what I try now where it was rather easy to blow it over with a quiet whistle before.
Other things Ive noted is that the page file now seems to be actively utilised. Ive pushed it at load up to almost 3gb where before the bios update I was struggling to see 400mb used. Not sure if that was part of it, but if you get simiar issues go straight to MSI and see about getting hold of the 1.5B3 bios or later.
To quickly address the recent replies:
1) Ive got to agree with HU16E with my ram. I have no trouble running at the 1333 JDEC spec. And I feel very positive about now being able to achieve the XMP spec with this new bios.
2) Thanks for the link Aaron. I did end up using the USB flash method from this forum. Worked perfectly. Chalk up another success story!
3) I did try to swap out the ssd last night, but the system kept soft rebooting while installing the OS on the spin drive. SO I gave up. Seems the ssd isnt a drawback under the new bios tho (assuming it even was a cause earlier).
4) Ive DL'ed the x64 windows 7 beta and I'll likely as not have a shot installing that and refitting the extra 3gb ram back into the system. I'll let you know how it goes. Theoretically 6x1gb sticks should be as much as 15-20% faster than 3x 2gb sticks (and were about that much cheaper for me at time of purchase) but I'll run some benchmarks now that the benchmarks work and let you know the differences in case anyone wants to build their box the same way.
Conclusion:
I'll stress the system over a bit for the next few days without overclocking and I'll see if I can bring the system to reboot like it did previously through high usage, and if I cant I'll change the thread to solved and write out a proper solution post for the problem, symptoms and solution.
Id like to take the opportunity to say thanks to all the guys who've given me help and advice. Youve all been really great. Thanks a bundle! I owe you one

Eclipse sli full board chipset water blocks?

Hi, I'm new to the these forums, but not a new MSI customer. I've had my eclipse sli since march '09 and was running everything @ stock. A couple of months ago a finally got around to OC'ing and noticed my IOH temps idling between 95-100c and 105-110c under load. I have since set everything back to stock and started searching for solutions, which led me to this thread. I have done the mod( HR-05 on IOH and I cut the heatsink for the ICH, I trust MSI boards.) and am pleased to report that my new IOH temps are 49-51c idle and 53-55c load. The strange thing is that my board seems to be clocking better because now with the stock heatsink I'm @ 3.5 with 1.26v stable whereas before the mod I was @ 1.3v stable on a custom loop. Which leads me to a question, sorry for being long winded and I'm not even sure if this is the right thread to ask it in but, Seeing that my lower IOH temps have given me the potential for a better clock I would like to add the IOH and ICH into the new loop I'm trying to put together, but I've looking all over for a full chipset waterblock for my eclipse sli and can't find any. Do they exist? Are they in production? or Are there any alternatives? Suggestions?

prymal, rename the title to suit your needs.
>> Posting Guide <<
I'll split and move this one to OC & Modding Corner.

Eclipse Sli, Leds on, No boot

Hi everybody,
I bought two days ago an Msi Eclipse for my new computer :
Mobo : Msi Eclipse Sli X58
Proc : I7 965 Extreme / Noctua NH-12 SE2
Ram : 3 * 2 Go Kingston Hyper X 1600Mhz
GC : ATI HD 4890 Vapor X
Power s. : Silencer 520 W
HD : Samsung SpinPoint 750 * 2 + 500 * 1
The problem :
When i switch on my PC leds are on and all fans work, but no signal on screen and Dled2 Off.
What i Tried :
Ram :
No ram
Only one
Corsair TwinX 1600
GC :
No GC
Fan :
All tower fans off
Nothing appened and the problem is still the same.
Regards,
Sky

Ok ,
So i successed :D and i'm still alive lol
I think it will be a little bit long to explain what i done in details so i resume :
I put the mobo on a table and used an air cleaner first.
Second, I put on the mobo only the cpu and the cpu fan, I made as you suggest me, clear cmos : the Dled2 worked but blocked on the DRAM.
Finaly I put the DDR3 only one slot and it didn't work , the post was still bloqued on the dram. I tried with an other old one , still bloqued, i put the three slots of the new one, it worked...
I don't know where was the real problem but if it can helps someone
Regards,
Sky

Eclipse SLI with Corsair TR3X3G1333C9 (OC Quesion)

Hi all,
Just starting out in trying to overclock and was windering what speeds people have managed to get on their rigs. Is there anyone out there that is using the board and memory (Eclipse SLI with Corsair TR3X3G1333C9 3x1GB).
- If there is anyone out there with the same hardware as me and has overclocked it.
- What speeds did you get and what setting did you use?
Thanks All,
Halvare

Hi halvare & welcome to the forum. An Admin. or Moderator will probably move your thread to the forum subject 'Overclockers & Modding Corner'. In the mean time, take a peak at the forum posting guide & other 'Sticky' topics to help with the details needed to provide the best answers for you. Provide a full list of system specs, as this will greatly increase the forum users ability to make recommendations. Use my signature below this post text as an example.

X58 Eclipse Sli with CMP12GX3M3A1600C9 how to make it run stable in 1600Hz?

Hello ,
I m new here, so forgive me if i make a mistake somewhere !
So my specs are :
motherboard: X58 Eclipse Sli(bios ver:1.F0 model:MS-7520)
CPU:i7 950 @ 3,07 (stock)
GPU: 2x GTX470(msi)
PSU:Thermaltake 1200watt
HD:1xSSD , 1xWD@10000rpm
and here is my story:
I have been using TR3X6G1600C9(corsair ver8.1) with XMP enabled so in 1600Hz and everything were going sweet stable pc , then i decided to put something more on it another TR3X6G1600C9(corsair) this time came different ver2.5 with XMP profile off seems work fine , with XMP on blue screen-restart so i asked in corsair forum they show a .pdf from corsair which was saying that mixing modules even with same kind of memory there are posibilities it wont be compatible-work.
Today i just replaced the 2xTR3X6G1600C9 with CMP12GX3M3A1600C9(corsair) enabled the XMP profile , everything was looking good all 12gb were working , but after some time i got blue screen and restart :(, so i bet this has to do with options and propably i have to do more than to enable XMP profile in order to make it stable. So any suggetions ? Yes i m totally noob from knowledge in bios only i know is to enable XMP but i m looking forward to learn stuff from ya guys and considering that i might just lost about 230e in order to upgrade ram and i can't make to work 12gb stable in 1600hz i should of ask much earlier!

Quote from: IcUfu on 19-May-11, 02:54:22
Hello ,
I m new here, so forgive me if i make a mistake somewhere !
So my specs are :
motherboard: X58 Eclipse Sli(bios ver:1.F0 model:MS-7520)
CPU:i7 950 @ 3,07 (stock)
GPU: 2x GTX470(msi)
PSU:Thermaltake 1200watt
HD:1xSSD , 1xWD@10000rpm
and here is my story:
I have been using TR3X6G1600C9(corsair ver8.1)(http://www.corsair.com/memory/xms-classic/xms3-ddr3-memory/tr3x6g1600c9.html) with XMP enabled so in 1600Hz and everything were going sweet stable pc , then i decided to put something more on it another TR3X6G1600C9(corsair) this time came different ver2.5 with XMP profile off seems work fine , with XMP on blue screen-restart so i asked in corsair forum they show a .pdf from corsair which was saying that mixing modules even with same kind of memory there are posibilities it wont be compatible-work.
Today i just replaced the 2xTR3X6G1600C9 with CMP12GX3M3A1600C9(corsair)( http://www.corsair.com/memory/dominator/dominator/cmp12gx3m3a1600c9.html) enabled the XMP profile , everything was looking good all 12gb were working , but after some time i got blue screen and restart :(, so i bet this has to do with options and propably i have to do more than to enable XMP profile in order to make it stable. So any suggetions ? Yes i m totally noob from knowledge in bios only i know is to enable XMP but i m looking forward to learn stuff from ya guys and considering that i might just lost about 230e in order to upgrade ram and i can't make to work 12gb stable in 1600hz i should of ask much earlier!
What i have done so far ,with CMP12GX3M3A1600C9 http://www.corsair.com/memory/dominator/dominator/cmp12gx3m3a1600c9.html
turned off XMP , put manually :1.DRAM freq-1600Hz 2. CAS timings 9-9-9-24 3.DRAM command rate 2N 4. DRAM Voltage 1.65 it did't crass again so far but i am afraid about this DRAM Voktage 1.65 is it posible that i will destroy my CPU this way??? The rest options in bios are setted to optimal defaults should i change something else in order to protect my CPU?

Error Message- you cannot post write up

HII friends
I have an issue that our client have posted unplanned depreciation to one asset which is wrong on 31/3/07. now they want to write up the same on the same date. but system is not allowing the same date it is giving error
YOU CANNOT POST WRITE UP.
Message details:
None of the areas to be posted in accordance with the transaction type entered manages one of the depreciation types entered or cumulative values
Please help its very urgent///
sejal

this issue is solved

Cannot post a reply

For whatever reason, although I am logged-in to Adobe Forums, I cannot post a reply to a message that was posted in reply to my original message (which began the discussion). A blank white space, barely discernible, is displayed below the two lines with their respective radion buttons for "Yes my question was answered." and "No, my question was not answered." The choice is "No", but I did not ask any question(s) to begin with.
Instead, I posted three screenshots which showed problems that I encountered while attempting to download and install the most recent update to Adobe Reader for Firefox. Someone posted a reply that the same problem occurs with Opera. I wanted to tell him that Firefox, Safari and Opera all use the same add-on for Adobe Reader.
But there was no way that I could discover to enter any text into the field for it. Javascript was enabled, or I would not have been able to use the Reply feature to access the screen on which the message was to be composed. The field never contained a cursor, regardless of my attempts to cause one to appear, whether with the mouse or with the keyboard. Please understand that I do NOT have any desire whatsoever to go to Jive Software, open an "account" with them, and attempt to engage in some problem-solving for their software. I am not a beta-tester!!   My name and other data about me is in far too many databases as it is. If you can't hire people whose product works, then DIY.
In fact, Adobe's use of subcontractors has become very alienating. When I attempted to update Adobe Reader on the evening of July 29, the process was a travesty. First, it was not clear whether the update in which the security vulnerablilities have been corrected was available, let alone installed. This is partly because your website maintainer(s) are too ignorant, or too lazy, to post the entire version number of the current Adobe Reader release. They just post "version 9.1" and omit anything after it. So they don't have to update the page until either of the two digits change. But it is the digits that follow "9.1." which disclose whether the version that I'm about to download (http://www.adobe.com/downloads) is the one that is already installed, or a version that is subsequent. Perhaps you are afraid that disclosing technical data that is actually useful will intimidate and alienate the artists and writers who are the primary users of your products (you're lucky that they aren't all running the Apple MacIntosh instead). But I doubt that will happen. It is the failure to disclose such data that will eventually alienate EVERYONE.
For what it is worth to you, I have posted the message text below at the following link:
http://techrepublic.com.com/5208-12846-0.html?forumID=102&threadID=314113&messageID=313100 9&alertspromo=100901&tag=nl.rCOMBINED
What makes a difference is
http://www.get.adobe.com instead of http://www.adobe.com/downloads.
{Update 2009-08-01: when I tried the first link with Firefox 3.5.1 today, Embarq, my ISP, displayed what used to be an HTTP 404 (?) error message but now is an Embarq website page that leaves you wondering why you are looking at it instead of what you wanted. I don't know what has happened to the first URL, but that was what Securnia PSI used during its downloads of the updates, as described below.}
I have used the second one for years, but now it has nothing but problems. Thanks for the link to the IE 8 download. What I did this evening was to first run Windows Update (with IE 7).
The MS update site offered: (A) upgrade to I.E. 8, (B) cumulative security update for I.E. 7 KB972260, and (C) Silverlight update to ver. 3.0.40723.0 KB970363. The one for Silverlight surprised me; it wasn't there on Tuesday 14 July. After all of them were installed, I ran I.E. 8 just to go through its initial configuration routine, so that it should not interfere with subsequently updating any add-ons.
Then I ran Secunia PSI and had it do a new scan. It reported updates: (A) for Adobe Air; (B) Adobe Flash Player (ActiveX) to 10.0.32.18; (C) Adobe Flash Player (General Plug-In) to 10.0.32.18; and (D) Shockwave Player 11.5.1.601. I used the Secunia "Download Solution" feature for each one; it obtained the respective updates from http://www.get.adobe.com. Secunia continued reporting the Flash Player version as 10.2.22.87 until I deleted Flash10b.ocx from the C:\Windows\system32\Macromed\Flash directory; the current one is Flash10c.ocx.
Curiously, Secunia did not report Adobe Reader as insecure or outdated, on my computer. AcroRd32.exe Properties > Version showed Version: 9.1.0.163 but also displayed File Version and Product Version as 9.1.0.2009022700. Control Panel > Add or Remove Programs reported the Adobe Reader version as 9.1.2. Go figure.
However, updating Adobe Reader via http://www.adobe.com/downloads on July 29 required installing two Firefox add-ons: an extension for the Adobe Download Manager, and a plug-in "getPlus+ for Adobe 16236" (if my memory is correct). Of course, there were a couple of .exe files under the radar in C:\Program Files\NOS and some more in C:\Documents and Settings\...\Application Data\NOS. After all of that, I subsequently learned, from looking at the Secunia report for I.E. Secure Browsing, that "NOS Microsystems getPlus ActiveX Control 1.x" is "insecure, no solution".
Already I wasn't happy about having one of the NOS executables installed as a service, as though that is what the memory must contain after every system boot. And I didn't like Yet Another Firefox Extension just for the convenience of one particular software developer and/or their distributor. Firefox already loads slower than I like and adding YAFFX like that makes it even slower to load.
So I uninstalled Adobe Reader and all of its Additional Ware from NOS; I found files from both all over the HDD. I think that I deleted everything that I don't want or need although the I.E. NOS ActiveX control remains. I have never downloaded a .PDF, or looked at one, with I.E. and I don't plan to, so maybe I should just get rid of that one, too, if I can.
For the time being, at least, I'll be looking at .PDF files with Foxit. Of course, Adobe Flash Player and Shockwave Player remain installed, with Adobe AIR and Adobe Download Manager.
Posted: 07/31/2009 @ 09:32 PM (PDT)                  (edited 08/01/2009 @ 06:18 PM (PDT))
As of this writing, I do not have any Adobe or NOS add-ons (extension or plug-in) installed in Firefox, and I am planning to remove the insecure ActiveX Control that has been installed for Internet Explorer 8.
Continue to follow your current strategy, and you won't have the burdens of maintaining either Adobe Flash Player or Shockwave Player as well. I had Adobe Media Player installed, but I removed it since I've never found a reason to run it.

Hi, Kath H.,
I hope that you heeded the warnings. Adobe has, however, released updates in which the security flaws have been corrected. From my reading of posts on some (non-Adobe) forums, what everyone has a problem finding is where to download the updates and/or to install them directly online.
The customary location is: http://www.adobe.com/downloads.
You will find three "buttons" labeled "Get Adobe Reader", "Get Adobe AIR", "Get Adobe Flash Player" and one hyperlink for "Get Shockwave Player". You need to update the ones that are installed on your computer (usually, at least Flash Player and Shockwave Player). The website button will automatically present you with the version that is appropriate for the browser that you are running at the time that you access the download.
BTW, please be aware that what I found at the customary Adobe downloads website on July 31 for Adobe Reader and Firefox was a travesty. I don't know whether Adobe has taken corrective measures since, but their "instructions for Firefox users" were outdated and simply wrong. I had already updated Adobe Reader on July 29, but I was not sure that I had actually obtained the update, since some people were reporting that they had to do it twice before it was installed correctly.
Something that may interest you is Secunia Personal Software Inspector (PSI). It inventories all of the software on your computer, and compares (via the Internet) each version that it finds to the Secunia database to check whether it is up-to-date, or it might be known to contain security flaws. An individual user can download, install and use Secunia PSI without charge (commercial use requires a license). You can obtain it from:
http://secunia.com/vulnerability_scanning/personal/
One feature is that, after Secunia PSI runs a "scan" of your software, it displays any "insecure" programs on a tab labeled "Insecure". Each entry has a [+] box which is expandable into an explanation, and a toolbar at the bottom with several actions that you can take, the first being "Download Solution" (when the software developer or publisher has a software update available). That is what I used to update the "insecure" Adobe Flash Player and Shockwave Player add-ons for Firefox (and for I.E., also, which I have installed but don't run often). Secunia PSI downloaded them from https://www.get.adobe.com but I haven't been able to connect there with the browser.
Since Secunia PSI did not report Adobe Reader as insecure, I have supposed that it was updated. (You can scan my first post here to find out why I uninstalled it and installed Foxit instead!)
   --- OldReader

Cannot post the shipment in SAP, stock showing as Unrestricted in MMBE

We are subcontracting to external vendor by creating PO in our routing step. we were able to ship the material to the vendor however "Cannot post the shipment in SAP" as a result the Unrestricted stock in MMBE is still showing. Any suggestions

Dear
Please review the steps involved in Sub-Contracting in Production Order : Operation Sub-Contracting
Subcontracting.
Did you try to send material in ME2O ?? Sub-Contracting Stock Monitoring for vendor ??
Did you create the Vendor frist in SAP ?? Check this Stock transport order..?
Did you maintain the correct shipping point in Purchasing view or STO through whivh u will trasfer the material TO VENDOR
Check all of them and come back
Regards
JH

Cannot post document : Tax base in local currency is zero

Hi,
I have an order with a down payment.
When I want to create the billing document, I get following error message:
Message no. FF759.
Cannot post document: tax base in local currency is zero.
You tried generating a document in which the tax base in local currency is zero although the tax amount and tax base in foreign currency is not zero.
I see in the sales order conditions that the VPRO is filled out.
Where can I check what is wrong?
How can I create the billing document?
Thank you.
Kind regards,
Linda

Hi,
Thanks for your reply.
The error message does not make sense.
We have maintained the exchange rates.
We only have postings in local currency (PLN).
In the order I can't find any zero values for the tax amount or the tax base.
But when we do a be-bugging, we get the following:
Error is being trown in LTAX2U27:
Prüfung: Steuer <> 0 und Steuerbasisbetrag = 0
IF ( i_bset-hwbas = 0 AND i_bset-hwste <> 0 ) OR
     ( i_bset-fwbas = 0 AND i_bset-fwste <> 0 ) OR
     ( i_bset-h2bas = 0 AND i_bset-h2ste <> 0 ) OR
     ( i_bset-h3bas = 0 AND i_bset-h3ste <> 0 ).
no error in case of external system is active             "N515047
AND billing document AND bas-amount = 0                  "N515047
prerequisite: note 549712                                 "N515047
    IF ext_activ IS INITIAL                              "N515047
    OR i_bkpf-awtyp NE 'VBRK'.                           "N515047
      message_store 'FF' 'E' '759' blank blank blank blank.
    ENDIF.                                                "N515047
ENDIF.
At the moment of entry fields have following values:
HWBAS     HWBAS_BSES     CURR     15     2     Tax Base Amount in Local Currency
FWBAS     FWBAS_BSES     CURR     15     2     Tax base amount in document currency
HWSTE     HWSTE     CURR     13     2     Tax Amount in Local Currency
FWSTE     FWSTE     CURR     13     2     Tax Amount in Document Currency
Do you have any idea to solve it?
Thank you!
Kind regards,
Linda

Eclipse SLI cannot post

Similar Messages

Maybe you are looking for