Edge E530 network card - 'no link'

Hello,
My Thinkpad edge of nearly 2 years has as of today stopped showing a carrier signal on it's network port.
This follows constant use under Slackware 14 since purchase (have tested with stock OS and knoppix). The first sign of trouble was in april this year when plugging in to a specific client network caused the transfer speed to slow to a permanent crawl after dhcp, and may have been triggered by plugging in to a bad wall socket at another site today.
Anyone had luck replacing them, are they too much hassle, and is there a good usb network card that could do the trick?
Shame to lose it, really liked these - and bought them for clients too.

Does the order in which you boot up the VMs have any impact on which one can reach the internet?
Such as; the first one that boots always gets out, no matter the VM.
This would point to a MAC limiting feature on your physical switch.
The other is, since you have teamed NICs, do both have active connections.
Brian Ehlert
http://ITProctology.blogspot.com
Learn. Apply. Repeat.
Disclaimer: Attempting change is of your own free will.

Similar Messages

  • MLS dual network card incorporation

    Hello
    I'm incorporating a technique into our network that uses a dual slot network card. The driver of these cards also makes it so that both NICs have the same MAC. both of the network cards are linked to a cicso 4500 catalyst switch. the link works however I get the error alert: MLS-4-moreoverflow. The switch recognizes the two as a looped mac by two different devices. I was wondering how to fix this problem or obtain documention for this problem.
    Thanks in advance for your time.

    Hello,
    I wonder if it would work when you configure the two switchports as an Etherchannel, effectively making both ports appear as one link. Can you try and add the following to both switchports:
    channel-group 1 mode desirable
    I have no equipment to test this configuration on...can you try and see if this works ?
    Regards,
    GP

  • Use only one network card with Edge

    hi,
    is it ok to configure single network card for the edge and do the static routing on that network card. is it supported if yes then kindly providee me the Technet article. If it is not supported then kindly provide me technet article which says that one network
    card for lync edge is not supported.
    Thanx
    SKHATRI

    Hello all,
    Thanks a lot for your post. May i know the following clarification as i want to use single interface at EDGE server.
    Unsupported Scenario
    A Consolidated Edge cannot be deployed with a single Network Interface in the environment as the roles has a requirement to have and bind separate IP addresses for internal and external services. At the same time, a single multihomed
    network adapter connected to a same IP sub-network for both internal and external routes is not supported for the A/V Edge role specifically.
    – Did not understand why not supported, in TCP/IP communication, what will be the issue? If I make sure that external and internal users see the EDGE server with different IP.  External
    users will see the EDGE server with public IP. The external users will not able to connect internal interface in any case.  Internal users/server will see the EDGE server with private IP. They will be able to connect with public IP /service (port).
     Besides that, if i use 2 NIC but IP will be from same subnet of DMZ what will be the issue.
    Appritiate your response.
    Thanks
    Ashif

  • Alternative to Intel Wifi Link 5100 AGN wireless network card?

    I'm finding that my Intel 5100 AGN wireless network card is not performing as well as it used to.  I've tried everything... even drivers are fully up to date.  But I keep losing connection to my wireless router, even though connection strength is between 3-4 bars.  I find that I rarely get dropped if I have 5 bars.  But if it weakens to 3, I get periodically dropped no matter what wireless network I am using.
    I want to replace this card with something better, but of course compatible with the HP dv5 (my specific model is dv5t-1000).  Any recommendations?
    "If you keep an open mind, life will give you more possibilities."
    This question was solved.
    View Solution.

    Hi, Gary:
    What I meant by my statement regarding you having the better of the available cards for your notebook is that, yes, I am sure the Intel 5300 is an improvement over the 5100, but the problem is you can't install the 5300 in your notebook.
    The Intel 5300 is not supported (only the cards/part numbers listed in the service manual can be installed) and your notebook wouldn't boot until you removed the card.
    You can try a different card listed in the manual if you want.
    However, you are limited to the:
    Broadcom 4322 802.11a/b/g/n WLAN module
    Broadcom BCM4312 802.11b/g WLAN module (not a wireless N card)
    I suppose you can use an external USB adapter but I would get one with an external antenna connected to it, because I would have to believe the 3 antenna wire setup in your notebook has to provide superior reception over a plain USB wireless adapter with an internal antenna as its only antenna.
    The antennas go all the way up to the top of your screen.
    Did you fiddle around with your network card's advanced settings?  They can be found by clicking on the card in the device manager, clicking on the advanced tab.  make a note of where the settings are now so if something goes buggy, you can change them back.
    Here is a guide to the advanced settings you have and the recommended settings for them.
    http://www.intel.com/support/wireless/wlan/sb/CS-025393.htm
    Paul

  • "White Listed" Wireless Network Cards

    I was wondering if anyone could tell me whether or not I could install a "Lenovo Branded" Intel Ultimate N Half-Mini Network Card in my ThinkPad Edge E530. I have upgraded to a SSD as well as 16 GB Ram, and would like to utilize these improvements over and above what my current Intel 2230 b/g/n can deliver. Since it is on the "White List", is there any way to adapt my machine to utilize its' potential? I have downloaded whatever "Access Connections" Lenovo offers, and installed all the pre-requisite software. Am I still limited to the two paltry offerings Lenovo has delineated for the E530......should this be the case, I'll never purchase another Lenovo machine.......
    I would really appreciate if someone more knowledgable than I could enlighten me regarding this frustrating restriction.....The "Access Connections" implied that downloading and installing the designated software would enable the use of any or all of the "supported devices". 
    Thanks to anyone and everyone in advance for shedding some light on this issue........fruhlpmd......
    Solved!
    Go to Solution.

    The white list is a per-machine-type thing.  It's part of the BIOS.
    Probably the best reference is the parts manifest for your machine:  http://download.lenovo.com/parts/ThinkPad/E530_FRU_BOM_V2.pdf
    From that PDF:
    60Y3195  FRU 6250 WiMax
    60Y3247  FRU FXC 11WLAN
    60Y3249  FRU LTN 11WLAN
    60Y3257  FRU Gobi3 WWAN
    60Y3297  FRU H5321w
    Unless the BIOS has been updated since that list, those are your options.  Make sure any card you choose actually has the Lenovo FRU.
    [edit] Hmm, I don't see the 2230 on that list.  There must be more to this story.
    Z.
    The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc.  The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

  • T520 won't detect Network card in WDS/WinPE/​Ghost image disk

    Hello all,
    I figured I would just post this so I could save 2 days of someone elses life.
    I'm not sure how many other modes have the EFI and UEFI bios's in them but this has caused a lot of problems when trying to capture an image / image the Lenovo T520.  So for anyone else that is having these problems here is how I got around the problem.
    The Problem:
    While trying to boot up off a Capture image with a CD or PXE boot for our WDS server the laptop would not detect the network card giving no IP address and listing the adapter as a hybrid.  When trying to do a ipconfig /renew it would give an error around the lines of the loopback something or other ....... the adapter could not be contacted or initated.
    I instantly thought this was due to the vanila WinPE / Capture image not having the drivers for the Lenovoo T520, so I went to the website downloaded the new drivers and injected them into the WinPE disk(You will want ot use the NDIS Drivers which are included in the package for this).  Following this process it would still not detect or install the NIC.  After many hours of searching it would apear this was due to the EFI/UEFI bios options not going through the proper boot cycle when in a PE enviroment.  The solution was to mess around with the EFI/UEFI switches in the WinPE boot image during the creation proccess as listed below:
    ocdimg -m -o -u2 -udfver102 -bootdata:2#p0,e,bc:\winpe_x64\etfsboot.com#pEF,e,​bc:\winpe_x64\efisys.bin c:\winpe_x64\ISO c:\winpe_x64\winpeuefi.iso
    The link with more details is here: http://support.microsoft.com/kb/947024
    Eseentially once the new boot image was complied with the proper EFI / UEFI options enabled it went through the proper boot process detected the NIC and installed the drivers which I previously provided on the disk and we where off to the races imaging the new laptop.
    Hopefull this will help some others who are struggling with this or any other model that has this type of bios.
    Cheers, and thanks
    Please feel free to post any additional comments to help others if you found better ways to get around this
    One side note the EFI/UEFI to legacy mode only does nothing for the NIC problem, I have seen some posts where they can help with the hard drive issues when imaging, however as for the nic not loading in PE enviroments this setting in the BIOS did not reslove the problem.

    Hi Rusty1234
    If I did not remember wrongly, you may present or add drivers (network, hardware) under WDS / Ghost software or copy necessary drivers (e.g. your T520 network card drivers) under it's PXE / boot section.
    Happy 2012! 
    Peter
    W520 (4284-A99)
    Does someone’s post help you? Give them kudos as a reward, as they will do better to improve | Mark it as solved if the solution works for you, so it could be reference for others in the future 
    =====================================
    Sound Enthusiast and Enhancement (Post comments, share mixes, etc.)
    http://forums.lenovo.com/t5/General-Discussion/Dol​by-Home-Theater-v4-for-most-Lenovo-Laptops/td-p/62​...

  • Network card not relinking..

    Last night, our local router siezed up and had to be rebooted.  When we brought the router back up, the network card in our proxy server(SuSE Linux) failed to link back up.  I was asked to look into the situation and see what kind of sollutions I could come up with.  Does any one have any suggestions.  I've seen ifplugd and it seems to be what we need, but does anyone have any experience working with this or any other suggested sollutions?  This is our first experience with a linux server in a production environment.  Also..just a note, the server runs SuSE linux because the admins that I work with like the sescurity of a support contract(understandably so). 
    Thanks

    medicated wrote:Wouldn't the system assume that the cable was uplugged?  It will no longer be linking up to anything, so whats the difference between that and simply unplugging the cable?
    dunno... I was just covering all the bases... I'm not sure how much of a "link down" ifplugd needs to reconnect... hitting a "reset" button might cause it to not relink... I dunno
    Best to just try it out on a desktop of your own (run ifplgud, shut the router off, restart... checking pings and whatnot the whole time)

  • Oracle Linux 6 update --- wirelees network card not working.

    Hello,
    The only problem I am having is with my wireless network card(built-in). Should I buy a new wireless card that can be used with Oracle Linux?
    Here is some info about my laptop:
    $ lspci -v | grep -i net
    04:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01)
    05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)
    $ iwconfig
    lo no wireless extensions.
    eth0 no wireless extensions.
    virbr0 no wireless extensions.
    virbr0-nic no wireless extensions.
    $ lsmod
    Module Size Used by
    fuse 49340 0
    ipt_MASQUERADE 1780 3
    iptable_nat 4651 1
    nf_nat 16615 2 ipt_MASQUERADE,iptable_nat
    iptable_mangle 2603 0
    tun 9430 1
    bridge 39245 0
    stp 1503 1 bridge
    llc 4140 2 bridge,stp
    autofs4 18216 3
    sunrpc 168053 1
    cpufreq_ondemand 6844 4
    powernow_k8 12957 0
    ipt_REJECT 1621 4
    nf_conntrack_ipv4 7140 6 iptable_nat,nf_nat
    nf_defrag_ipv4 1033 1 nf_conntrack_ipv4
    iptable_filter 2123 1
    ip_tables 8337 3 iptable_nat,iptable_mangle,iptable_filter
    ip6t_REJECT 3390 2
    xt_tcpudp 1879 6
    nf_conntrack_ipv6 14880 2
    xt_state 1042 5
    nf_conntrack 59159 6 ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv4,nf_conntrack_ipv6,xt_state
    ip6table_filter 2231 1
    ip6_tables 9601 1 ip6table_filter
    x_tables 12478 8 ipt_MASQUERADE,iptable_nat,ipt_REJECT,ip_tables,ip6t_REJECT,xt_tcpudp,xt_state,ip6_tables
    ipv6 225173 34 ip6t_REJECT,nf_conntrack_ipv6
    uinput 5260 0
    rfkill 13768 1
    i2c_piix4 10150 0
    joydev 7304 0
    microcode 11243 0
    uvcvideo 47429 0
    videodev 29537 1 uvcvideo
    v4l1_compat 11137 2 uvcvideo,videodev
    i2c_core 23454 2 i2c_piix4,videodev
    pcspkr 1386 0
    serio_raw 3380 0
    r8169 29689 0
    mii 3889 1 r8169
    snd_hda_codec_realtek 197227 1
    snd_hda_codec_atihdmi 2039 1
    snd_hda_intel 19505 2
    snd_hda_codec 62689 3 snd_hda_codec_realtek,snd_hda_codec_atihdmi,snd_hda_intel
    snd_hwdep 4852 1 snd_hda_codec
    snd_seq 43513 0
    snd_seq_device 5326 1 snd_seq
    snd_pcm 63799 2 snd_hda_intel,snd_hda_codec
    snd_timer 16064 2 snd_seq,snd_pcm
    snd 49098 12 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_seq_device,snd_pcm,snd_timer
    soundcore 5387 1 snd
    snd_page_alloc 6456 2 snd_hda_intel,snd_pcm
    usb_storage 35626 0
    ahci 28838 2
    pata_acpi 2307 0
    ata_generic 2403 0
    pata_atiixp 2852 0
    ohci_hcd 25812 0
    video 16346 0
    output 1723 1 video

    The actual problem seems to be that you are using the wrong Linux distribution for you Laptop. Enterprise Linux was not designed for consumer grade hardware. To further troubleshoot the problem you will need to check for relevant output of "dmesg", i.e. check if the firmware and driver that was loaded for the device. You should also check "lspci -v" w/o grep to see more detailed information for the device.
    Are you trying the latest Oracle Linux 6 update 2?
    What is your hardware?
    Beware that no Oracle database products are yet certified for EL6 yet, so you should better stick to Oracle Linux 5 update 7 instead.
    If the purpose of your installation is research and development I suggest to install Windows as your primary OS and run Oracle Linux inside Virtualbox. Check the following link: http://www.oracle.com/technetwork/community/developer-vm/index.html

  • Difficulty getting my network card to work.

    Hey there,
    I recently converted to arch after the recent kernel update and currently love it. However, even though my network card should be supported, I'm having trouble connecting to any network, whether it be from ethernet or wireless.
    I was able to connect to a network through ethernet during the install but not anymore.
    I'm rocking a MSI GP60 2PE Leopard using the most up to date version of arch.
    [jonathan@j0nbiz-arch ~]$ lspci
    00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06)
    00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06)
    00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06)
    00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06)
    00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05)
    00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04)
    00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05)
    00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05)
    00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5)
    00:1c.3 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #4 (rev d5)
    00:1c.4 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #5 (rev d5)
    00:1c.5 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #6 (rev d5)
    00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05)
    00:1f.0 ISA bridge: Intel Corporation HM86 Express LPC Controller (rev 05)
    00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05)
    00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05)
    01:00.0 3D controller: NVIDIA Corporation GM108M [GeForce 840M] (rev a2)
    03:00.0 Ethernet controller: Qualcomm Atheros Killer E220x Gigabit Ethernet Controller (rev 13)
    04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5249 PCI Express Card Reader (rev 01)
    [jonathan@j0nbiz-arch ~]$ ip link
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
        link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    2: enp3s0: <BROADCAST,MULTICAST> mtu 1500 qdisc fq_codel state DOWN mode DEFAULT group default qlen 1000
        link/ether 44:8a:5b:42:a4:86 brd ff:ff:ff:ff:ff:ff
    I might be missing a lot of info but this is the first time I'm posting for help.
    Any help is appreciated! Thanks in advance.

    Welcome to the forums.  Please use code tags when posting command output - and see the stickied threads in this subforum and the forum etiquette guide on the wiki.
    Your ethernet cards is found by `lspci` and `ip link` - all seems in order there so far.  What have you done to try to connect?  The simplest test would be the following:
    sudo dhcpcd enp3s0
    If that works, then all is well and good, see the wiki on how to get connected automatically at start up.  If the above command fails, please post the error messages it provides.
    For wireless, lspci doesn't even show any wireless hardware - perhaps it is a usb interface for the wireless, what is the output of the following:
    dmesg | grep usbcore

  • Windows, RAC and network card problems... ?

    Dear friends,
    I've a problem! :)
    Here are some info:
    Node Hardware:
         Processor: Intel(R) Xeon(R) CPU E7430 @2.13GHz (2 processors)
         Installed memory(RAM): 52.0 GB
         System type: 64-bit OS
         Windows edition: Windows server 2008 R2 Enterprise
    Network cards (Shown by WIN):
         PublicLAN: HP NC373i Multifunction Gigabit Server Adapter
         PrivateLAN: HP NC373T PCle Multifunction Gig Server Adapter
         Offline: HP NC373T PCIe Multifunction Gig Server Adapter
    Software:
         Windows 2008 R2 Enterprise (Very last updates from MS)
         Oracle RAC 11.2.0.2.0 (Clusterware, DB) – 2 nodes
    Environment:
         AD network. Everything is MS based.
    Problem description:
    During RAC installation, company had only one network card (server network card, per node). Installation was successfully finished. RAC was/is in production. Has some problems, but noting for alarm.
    This days, we get other network cards. (purpose: network redundancy).
    RAC shutdown was clean.
    Network card inserted to nodes by OS Admin.
    Nodes was started up... and...
    OS Admin disabled network card immediately after logon screen was available... but to late...
    Windows changed network card order!!! PublicLAN was not at the first place when Cluster started (Network and sharing center -> change adapter settings -> Advanced (from menu) -> Advanced Settings -> Adapters and Bindings)!!! (I found in logs that MAC address changed at this point!)
    Cluster started hardware reconfiguration... and... we could not stop CW till starting up finished... ! After stopping CW again, we set PublicLan at first place, and every win setting was as at the moment of installation.
    Cluster was started again, DB, OEM too...
    Everything is working. Client can connect to DB, applications work well... but...
    Damage is done... now we have totally new IP situation inside... changes are saved to the DNS, too!!!
    Before inserting network card IP settings (nslookup from any client) :
    rac1 192.168.217.60
    rac1-vip 192.168.217.62
    rac2 192.168.217.61
    rac2-vip 192.168.217.63
    rac-scan 192.168.217.64
    192.168.217.65
    192.168.217.66
    After this incident (nslookup from any client):
    rac1 192.168.217.60
    192.168.217.62
    192.168.217.64
    192.168.217.66
    rac2 192.168.217.61
    192.168.217.63
    192.168.217.65
    192.168.217.66
    VIP and SCAN IP address are the same as before...
    nslookup show as that rac1,rac2,rac-scan change IP addresses in round-robin scenario!!!
    We stopped RAC couple of time and OS Admin cleared DNS records (both zone)... but every start of cluster make changes again in DNS.
    Other "side-effects":
    Some cluster commands, invoked from CMD, fire errors (lsnodes, cluvfy comp nodecon -n rac1,rac2).
    Configuration files seem to be correct (listeners, scan, scan_listeners, etc). srvctl and crsctl command are working without errors. oifcfg too.
    Logs are full of errors (like: ASM could not be reached... no listener)
    Listener(s) stop working sometime...
    Relocation of resource are not possible.
    Well, I mentioned the most important things... other alerts and errors in logs are present, but everything is connected with this issue, I think...
    As I said: RAC working. Clusterware, DB, OEM, connections, applications, backup... everything look good... but we have a problem!!!
    Any ideas, any suggestion, any link, any advice, anything are welcome!
    Thanks!
    PS.
    Metalink haven't any document about this... I've found a lot of examples for changing IP's, interfaces, interconnection... but noting about fixing problem!

    I'm having the same issue. My desktop pc keeps dropping the connection to my network (airport extreme router) while the rest of my devices (macbook pro, xbox, mac mini) still stay connected. The pc never had this issue prior to installing Windows 7 so im guessing there must be something with the Windows 7 OS.

  • Xennet error, when tried to add new network card

    Hi,
    I got an error when I tried to create new virtual network thru VM manager,
    I have add a new virtual network card thru VM manager in the same Xen bridge "xenbr0" , then i reboot the virtual machine, but when i tried to activate this network I got the below error:
    cannot activate network device
    xennet device eth1 does not seem to be present, delaying initialization.
    ifconfig in the virtual machine:
    dev13248 Link encap:Ethernet HWaddr 00:16:3E:0B:DD:E4
    BROADCAST MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    eth0 Link encap:Ethernet HWaddr 00:16:3E:5A:3E:6E
    inet addr:192.168.2.102 Bcast:192.168.2.255 Mask:255.255.255.0
    inet6 addr: fe80::216:3eff:fe5a:3e6e/64 Scope:Link
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:204 errors:0 dropped:0 overruns:0 frame:0
    TX packets:48 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:47253 (46.1 KiB) TX bytes:5623 (5.4 KiB)
    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:1045 errors:0 dropped:0 overruns:0 frame:0
    TX packets:1045 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:1458998 (1.3 MiB) TX bytes:1458998 (1.3 MiB)
    sit0 Link encap:IPv6-in-IPv4
    NOARP MTU:1480 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    ifconfig in the VM server:
    eth0 Link encap:Ethernet HWaddr 00:1C:C4:46:AF:3D
    inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:110 errors:0 dropped:0 overruns:0 frame:0
    TX packets:98 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:13177 (12.8 KiB) TX bytes:17612 (17.1 KiB)
    eth1 Link encap:Ethernet HWaddr 00:1C:C4:46:AF:3E
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:2052 (2.0 KiB)
    eth2 Link encap:Ethernet HWaddr 00:1C:C4:A6:B8:0E
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    eth3 Link encap:Ethernet HWaddr 00:1C:C4:A6:B8:10
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:127 errors:0 dropped:0 overruns:0 frame:0
    TX packets:127 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:11984 (11.7 KiB) TX bytes:11984 (11.7 KiB)
    peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:127 errors:0 dropped:0 overruns:0 frame:0
    TX packets:92 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:14405 (14.0 KiB) TX bytes:17422 (17.0 KiB)
    Interrupt:21
    peth1 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    Interrupt:23
    peth2 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    Interrupt:16 Memory:f8000000-f8011100
    peth3 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    Interrupt:23 Memory:fa000000-fa011100
    vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:98 errors:0 dropped:0 overruns:0 frame:0
    TX packets:110 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:17612 (17.1 KiB) TX bytes:13177 (12.8 KiB)
    vif0.1 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:6 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:2052 (2.0 KiB) TX bytes:0 (0.0 b)
    vif0.2 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    vif0.3 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:12 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:2236 (2.1 KiB) TX bytes:0 (0.0 b)
    xenbr1 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:6 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:1968 (1.9 KiB) TX bytes:0 (0.0 b)
    xenbr2 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    xenbr3 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    Don't inject the Windows 7 version of the driver into your WinPE image. Depending on what version of ADK you are using determines what version of the driver you will inject into WinPE.  If you are using MDT 2013 with ADK 8.1 you are using WinPE 5.0/5.1
    which is basically Windows 8.1. Make a selection profile explicitly for your WinPE drivers to inject. Only include the drivers you want in the WinPE image. And match the architecture of the network and storage drivers (Windows 8.1 versions).
    Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

  • Network card: e1000g (Intel PRO/1000 MT) did not working properly

    Hi to everyone!
    I'm having some strange trouble.
    All computers attached to one DLink gigabit switch
    Server #1:
    nf4-based motherboard, Intel PRO/1000 MT net card, onboard net card (forcedeth driver used) Ubuntu Linux 2.6.25 kernel version.
    All just working.
    Server #2:
    nf6-based motherboard, same Intel net card, SunOS 5.11 snv_86.
    All just working.
    Server #3:
    Same as server's #1 nf4-based motherboard. Same onboard card. Same SunOS 5.11 snv_86 as server #2 have installed.
    Its work. BUT..
    Intel card is not working as expected.
    It is seen by system. It is properly up and running. It is sending packent and receiving packets. Ierrs=Oerrs=Collis=Queue=0.
    But thru e1000g0 interface no one computer can reach this one, and from server #3 no one computer is seen thru e1000g0. Exept...
    Except two old Sunray1 devices (attached to the same switch for testing purposes)! But even these devices seen only by arp requests, and is not pingable.
    It is some mistery, but if I turn on jubmo frames, these rays got a picture from SRSS, testing on this sevrer! Not for long, heh, they hung up fast, but this is proof a physical connection :)
    So, I can not disable onboard network card on Server #3 - server becoming unreachable :(
    I know, those network cards must work on Solaris - as they did it on server #2. I know, those network cards work with my nf4-based motherboards - as they did it on server #1.
    But I can't uderstand, whait is going on with e1000g driver on server #3!
    P.S. Kernel driver e1000g settings are the same. All difference from servers #2 and #3 is: #2 had Intel netcard installed then Solaris was setting up, and #3 had Intel netcard installed later. All netcards are working (I trying to swap them from one computer to another - did not change anything).

    *) #3 thinks it is sending, but a NIC/driver error prevents it.NIC is fully health. It is tested on another PC. Driver error - or driver's bad implementation - is the one I'm thinking.
    *) #3 has a bad transmit pair of wires (would affect all communication)This patchcord works w/o problems on other PCs and even on onboard NIC of server #3.
    *) Network problemsHeh :)
    *) Firewall or other device is dropping the ARP repliesIt is some very stealthy and very selective firewall, affecting only external NICs :)
    BTW, then cord is attached to NIC, it sends "who has this IP" requests, asking to be shure there will not be an IP conflict. No one seen this requests.
    *) #1 has a NIC/driver error preventing it from seeing the reply.Only for send from #3? It is like a firewall on #3 :) And, there is more PCs, not only #1-#3. No one can see #3's replays (or asks), not only #1..
    I'm repeating: this PC works in network now on onboard NIC w/o problems. But onboard NIC is only 100 Mb/s, and we need 1 Gb/s.
    I was thinking, Solaris took wrong MAC for NICs - but not, ifconfig shows the same MACs as marked on NICs.
    Even more, yesterday i plumbed e1000g1 - second Intel NIC in server #3. And I was surprised - it worked perfectly!
    But I make "touch /reconfigure; init 6" - and after reboot, no one of two Intel NICs working again :( They both have the same behavior - no one can see packets they sends.)
    I even try to restrict connection on 100 Mb/s by driver's .conf modify - it works, link become yellow instead of green (take a note, NIC is able to "speak" properly with switch!), but all other stay the same.
    Strange, really strange behavior. More strange is a fact this NICs work on another instance of same SunOS, but on different motherboard, while the same MB with same NIC is working w/o problems under Ubuntu. Looks like some bug in Solaris driver.

  • Udev, two network cards

    Hi!
    I installed ARCH again. I didn't configure Xorg7 yet because I play with udev and my network cards. I have one integrated on the motherboard (3Com) which I use for Internet and I have D-Link card which I did use with my wifes computer and I live this card in for future. During installation was okay but after update I have a problem. Now I use a wifes computer and at this momemnt after sixt reboot network works.
    How can i save this problem, please?
    Mitja

    lumiwa wrote:
    Hi!
    I installed ARCH again. I didn't configure Xorg7 yet because I play with udev and my network cards. I have one integrated on the motherboard (3Com) which I use for Internet and I have D-Link card which I did use with my wifes computer and I live this card in for future. During installation was okay but after update I have a problem. Now I use a wifes computer and at this momemnt after sixt reboot network works.
    How can i save this problem, please?
    Mitja
    Some information more:
    lsmod show me now when network works skge and sk98lin.
    dmesg | grep etho:
    skge eth0: addr....skge eth0: enabling interfaces
    skge eth0: Link is up to 100 Mbps...
    and on the end:
    eth0: no IPv6 routers present

  • Replacement wired network card and driver for G4/OSX 10.3.9???

    Does anyone know of a wired network card that will work in a Mac (with or without a driver) when the one on the mother board is not longer functioning? It seems that my built-in Ethernet card was fried in a recent electrical storm and I'm looking for a replacement so I can connect to the internet again. My cable internet modem and cables were replaced after the storm and have been determined to be in working order.
    No theories, please -- I'm looking for a proven solution.

    Hi
    I found the Kingston KNE100TX (NB not KNE110TX) to be satisfactory in my B&W G3.
    Drivers required and available from Kingston up to OS9. No drivers required for OSX. See
    http://www.xlr8yourmac.com/OSX/osx_networkcards.html#kingston
    (There are other reports in this linked page but my experience is with the KNE100TX)
    Best wishes
    John
    G4 Quicksilver/733/1GB/80GB(ATA)+18GB(SCSI)   Mac OS X (10.4.7)  

  • Network Card XP Driver Configuration

    I've installed winxp home in Imac 17'', but it doesn't detect the network card.
    How can I install the correct drivers? Does anyone know what is the card's label so I can download the drivers.

    Just an idea for you. There is an entire Apple Discussion forum dedicated to Boot Camp and Windows XP.
    Whereas, not everyone here with an Intel iMac has installed, tried to install or has experience with BC & XP, everyone there has or at least has an interest. You may attract help more quickly there.
    The Forum is at the bottom of the main Apple Discussions page under Windows Compatible Technology.
    Here is a link;
    Forum: Boot Camp Public Beta

Maybe you are looking for