Edimax & 6510

Recently purchased 6510 and wireless set-up went fine and worked just fine with my ethernet connected PCs, one running Windows XP and the other Vista. Installation on both no problem and they still work just fine. Then purchased new laptop running windows 7 and connected to router via ethernet initially to instal latest drivers from HP rather than the disk supplied. Printing and scanning work just fine. Then disconnected ethernet and got successful network connection via the wireless connection on the Edimax router. However, I cannot print when my laptop is connected via the wireless network. Internet is just fine on wireless connection, I just can't print. If I leave a job in the Queue, and then plug the Ethernet cable back in, it prints almost immediately.
Have tried switching off various elements and switching back on but to no avail. I also note that my IPAD cannot see the router or the printer although it, and my laptop appear in the Edimax list of devices when I look for them. This one has got me beat. Oh, by the way, I ran all of the HP diagnostic software, and that didn't provide a solution either. Any suggestions would be really welcome.
By the way I installed a similar setup in Spain with a 5510 printer but with a Draytek 2830 router and had absolutely no problems at all with wireless laptop and iPAD working just fine and also PC plugged directly into router via Ethernet. Could this be a router issue???
This question was solved.
View Solution.

Neonskeleton
Thanks for all your input. I decided it
had to be something to do with the router and its settings, so rather than go through the Edimax ask a question and never get a reply routine I had a closer look at a couple of the settings and tried a couple of changes on my router. In the advanced settings for the wireless element there were a couple of choices for 'Relay Blocking' and 'Protection'. Both of these were 'Enabled' so I changed them to 'Disabled' and low and behold the printer now works from my lap-top and from the iPAD, have yet to try the notebook, but I suspect it will be OK.
As there is no documentation with this router and the 'on screen' help is non-existent it is not obvious to me what these two changes may have invoked in terms of fire walling, but I'm hoping I'm OK and have not opened up my system too much. I still have MAC addressing to restrict which devices can see the router and get through to the internet, so I think I will probably be OK.
Only have a remaining issue of why I always have problems from this new laptop when it comes to printing a Web Page (Always comes up with an error) and why I can't print anything from my 'Live Mail', but that can keep for another day.
Thanks for you hints and advice in your various posts, at least it got me thinking in the right direction, and i eventually found a solution. Many Thanks.

Similar Messages

How do i use my mac book with my HP 6510 e all in one series printer

how do i use my mac book with HP photosmart 6510 e all in one series

Hello Marilynatsea,
Thanks for using Apple Support Communities.
To learn more about printing in OS X on your Mac, and how to add a printer, take a look at the article linked to below.
Mac Basics: Printing in OS X - Apple Support
Cheers,
Alex H.

HP Photosmart 6510 e-All in One Series I want it to print off my PC in just Black and not Colour?

Please help! I have been in to settings for the printer on my Lap-top and can not find anywhere that will allow me to adjust to just printing in Black and White when I need it and not Colour all the time, which it is doing!

Hi @Anna11,
Welcome to the HP Forums!
I understand that you are trying to print in black only instead of color with your HP Photosmart 6510. I am happy to help with changing these settings!
For further assistance, I will need to know some more information:
If you are using a Windows or Mac Operating System, and the version number. To find the exact version, visit this link. Whatsmyos.
If the full feature software and drivers has been installed.
Please see this post, Want Good Answers? Ask Good Questions, by @Bob_Headrick, so you can get the most out of these forums.
Thank you for posting, and I hope to hear from you soon!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Photosmart 6510 e-ALL-IN-ONE Series offline

I can't get my 6510 all in one to go back on-line. I have windows 7 on my hp laptop and use my android phone as my wireless connection - this has worked perfectly for the past two years. I ran a wireless network test and the printer indicates PASS on connected. I've shut my printer off and turned back on. I did scan some pictures last weekend so I'm wondering if that has changed something. Any help is greatly appreciated.

Hi Williamstw
I understand you are unable to get the Photosmart 6510 back on line.
I have provided a document for the printer being offline to take a look at.
Hope this helps.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

PhotoSmart 6510 e All-IN-ONE Series HP Printer

My HP Photosmart 6510 e-All- In -One printer suddenly stoped coping, and delivers blank pages. When I print from my laptop the printer works but the quality is poor; printing faded out areas within the printed-out paper process. I tries cleaning the Pringheads, but got no resolve to my issue. Can anyone give advice on eliminating my problem?

When you replaced the printer cartridges did it clear up the problem?
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

How to print out wallet size photos on 6510 e-all-in-one series photosmart printer

want to print out wallet size photos (size 3 and a half x 2 and a half). I have windows XP and my printer is the photosmart 6510 e-all-in-one series

You will have to change the settings in the photo editing software and put 2 wallets on a 4x6 or 9 wallets on a full page. The photo tray will not take paper smaller than 4x6.
SandyBob
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP
1-800-474-6836

Connection constantly dropping with edimax ew-7612uan USB adapter

Hi there,
I have just installed a newly purchased edimax ew-7612uan USB wireless adapter, the problem that I'm getting is that the connection works fine on boot however it keeps dropping very frequently.
This can be reset by running netctl restart my-network. which is a temporary fix but I can't keep on doing this every 5 minutes or so when the connection drops.
I don't think there is a problem with the USB adapter as it appears to work fine in windows (I don't work fine with windows though!).
The same problem has happened on both of my Arch computers... I don't use any other distributions so I don't know if this is an arch specific problem or a general Linux problem. It also happens when using the live disk.
The old adapter is still installed in the box but once I can get this one working properly it will be removed.
The output of dmesg is as follows
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.13.8-1-ARCH (tobias@T-POWA-LX) (gcc version 4.8.2 20140206 (prerelease) (GCC) ) #1 SMP PREEMPT Tue Apr 1 12:19:51 CEST 2014
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=104c8e28-5731-4470-8911-313aca8c0d0f rw quiet
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f000-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007fedf7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007fedf800-0x000000007fedffff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007fee0000-0x000000007fee2fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007fee3000-0x000000007feeffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000007fef0000-0x000000007fefffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f3ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.4 present.
[ 0.000000] DMI: HP-Pavilion GB394AA-ABU a6030.uk/LEONITE, BIOS 5.17 04/20/2007
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x7fedf max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CEFFF write-protect
[ 0.000000] CF000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07FF00000 mask FFFF00000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [mem 0x000f5f40-0x000f5f4f] mapped at [ffff8800000f5f40]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01b3e000, 0x01b3efff] PGTABLE
[ 0.000000] BRK [0x01b3f000, 0x01b3ffff] PGTABLE
[ 0.000000] BRK [0x01b40000, 0x01b40fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x7fc00000-0x7fdfffff]
[ 0.000000] [mem 0x7fc00000-0x7fdfffff] page 2M
[ 0.000000] BRK [0x01b41000, 0x01b41fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x7c000000-0x7fbfffff]
[ 0.000000] [mem 0x7c000000-0x7fbfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x7bffffff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x7bffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x7fe00000-0x7fedefff]
[ 0.000000] [mem 0x7fe00000-0x7fedefff] page 4k
[ 0.000000] BRK [0x01b42000, 0x01b42fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x379ea000-0x37cecfff]
[ 0.000000] ACPI: RSDP 00000000000f8310 000024 (v02 HPQOEM)
[ 0.000000] ACPI: XSDT 000000007fee30c0 000054 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
[ 0.000000] ACPI: FACP 000000007fee7a80 0000F4 (v03 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
[ 0.000000] ACPI: DSDT 000000007fee3280 004798 (v01 HPQOEM SLIC-CPC 00001000 MSFT 03000000)
[ 0.000000] ACPI: FACS 000000007fee0000 000040
[ 0.000000] ACPI: SLIC 000000007fee7cc0 000176 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
[ 0.000000] ACPI: HPET 000000007fee7e80 000038 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000098)
[ 0.000000] ACPI: MCFG 000000007fee7f00 00003C (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
[ 0.000000] ACPI: APIC 000000007fee7bc0 000084 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
[ 0.000000] ACPI: SSDT 000000007fee8460 000304 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000007fedefff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x7fedefff]
[ 0.000000] NODE_DATA [mem 0x7feda000-0x7fedefff]
[ 0.000000] [ffffea0000000000-ffffea0001ffffff] PMD -> [ffff88007d600000-ffff88007f5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0x7fedefff]
[ 0.000000] On node 0 totalpages: 523901
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 8124 pages used for memmap
[ 0.000000] DMA32 zone: 519903 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.000000] e820: [mem 0x7ff00000-0xefffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88007fc00000 s86336 r8192 d24256 u524288
[ 0.000000] pcpu-alloc: s86336 r8192 d24256 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 515692
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=104c8e28-5731-4470-8911-313aca8c0d0f rw quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 2047396K/2095604K available (5271K kernel code, 836K rwdata, 1676K rodata, 1124K init, 1324K bss, 48208K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[ 0.000000] NR_IRQS:8448 nr_irqs:712 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 8388608 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2133.881 MHz processor
[ 0.003339] Calibrating delay loop (skipped), value calculated using timer frequency.. 4269.58 BogoMIPS (lpj=7112936)
[ 0.003343] pid_max: default: 32768 minimum: 301
[ 0.003383] Security Framework initialized
[ 0.003400] AppArmor: AppArmor disabled by boot time parameter
[ 0.003402] Yama: becoming mindful.
[ 0.003637] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.004945] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.005645] Mount-cache hash table entries: 256
[ 0.005953] Initializing cgroup subsys memory
[ 0.005966] Initializing cgroup subsys devices
[ 0.005969] Initializing cgroup subsys freezer
[ 0.005972] Initializing cgroup subsys net_cls
[ 0.005975] Initializing cgroup subsys blkio
[ 0.006006] CPU: Physical Processor ID: 0
[ 0.006008] CPU: Processor Core ID: 0
[ 0.006011] mce: CPU supports 6 MCE banks
[ 0.006021] CPU0: Thermal monitoring enabled (TM2)
[ 0.006030] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32
tlb_flushall_shift: -1
[ 0.006122] Freeing SMP alternatives memory: 20K (ffffffff819ec000 - ffffffff819f1000)
[ 0.007776] ACPI: Core revision 20131115
[ 0.010162] ACPI: All ACPI Tables successfully acquired
[ 0.013362] ftrace: allocating 21068 entries in 83 pages
[ 0.023793] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.057912] smpboot: CPU0: Intel(R) Core(TM)2 CPU 6420 @ 2.13GHz (fam: 06, model: 0f, stepping: 06)
[ 0.059999] APIC calibration not consistent with PM-Timer: 4652ms instead of 100ms
[ 0.059999] APIC delta adjusted to PM-Timer: 3346453 (155709996)
[ 0.059999] Performance Events: PEBS fmt0-, 4-deep LBR, Core2 events, Intel PMU driver.
[ 0.059999] perf_event_intel: PEBS disabled due to CPU errata
[ 0.059999] ... version: 2
[ 0.059999] ... bit width: 40
[ 0.059999] ... generic registers: 2
[ 0.059999] ... value mask: 000000ffffffffff
[ 0.059999] ... max period: 000000007fffffff
[ 0.059999] ... fixed-purpose events: 3
[ 0.059999] ... event mask: 0000000700000003
[ 0.083418] x86: Booting SMP configuration:
[ 0.089999] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.083422] .... node #0, CPUs: #1
[ 0.089999] x86: Booted up 1 node, 2 CPUs
[ 0.089999] smpboot: Total of 2 processors activated (8538.17 BogoMIPS)
[ 0.090131] devtmpfs: initialized
[ 0.093350] PM: Registering ACPI NVS region [mem 0x7fee0000-0x7fee2fff] (12288 bytes)
[ 0.094547] RTC time: 8:54:04, date: 04/02/14
[ 0.094607] NET: Registered protocol family 16
[ 0.094741] cpuidle: using governor ladder
[ 0.094743] cpuidle: using governor menu
[ 0.094771] ACPI: bus type PCI registered
[ 0.094774] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.094845] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
[ 0.094848] PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in E820
[ 0.094848] PCI: Using configuration type 1 for base access
[ 0.094952] mtrr: your CPUs had inconsistent fixed MTRR settings
[ 0.094954] mtrr: your CPUs had inconsistent variable MTRR settings
[ 0.094955] mtrr: probably your BIOS does not setup all CPUs.
[ 0.094956] mtrr: corrected configuration.
[ 0.096731] bio: create slab <bio-0> at 0
[ 0.096745] ACPI: Added _OSI(Module Device)
[ 0.096745] ACPI: Added _OSI(Processor Device)
[ 0.096745] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.096745] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.100165] ACPI: SSDT 000000007fee7f80 000175 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
[ 0.100379] ACPI: Dynamic OEM Table Load:
[ 0.100382] ACPI: SSDT (null) 000175 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
[ 0.100470] ACPI: SSDT 000000007fee8390 0000CE (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
[ 0.100675] ACPI: Dynamic OEM Table Load:
[ 0.100678] ACPI: SSDT (null) 0000CE (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
[ 0.100813] ACPI: Interpreter enabled
[ 0.100824] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131115/hwxface-580)
[ 0.100840] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.100842] ACPI: Using IOAPIC for interrupt routing
[ 0.100873] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.100967] ACPI: No dock devices found.
[ 0.103333] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.103333] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.103333] acpi PNP0A08:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.103333] acpi PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.103333] acpi PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.103333] acpi PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.103333] acpi PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
[ 0.103333] acpi PNP0A08:00: host bridge window [mem 0x7ff00000-0xfebfffff] (ignored)
[ 0.103333] PCI: root bus 00: using default resources
[ 0.103333] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.103333] PCI host bridge to bus 0000:00
[ 0.103333] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.103333] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.103333] pci_bus 0000:00: root bus resource [mem 0x00000000-0xfffffffff]
[ 0.103333] pci 0000:00:00.0: [8086:2770] type 00 class 0x060000
[ 0.103333] pci 0000:00:01.0: [8086:2771] type 01 class 0x060400
[ 0.103333] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.103333] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
[ 0.103333] pci 0000:00:1d.0: reg 0x20: [io 0xff00-0xff1f]
[ 0.103333] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.103333] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
[ 0.103333] pci 0000:00:1d.1: reg 0x20: [io 0xfe00-0xfe1f]
[ 0.103333] pci 0000:00:1d.1: System wakeup disabled by ACPI
[ 0.103333] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
[ 0.103333] pci 0000:00:1d.2: reg 0x20: [io 0xfd00-0xfd1f]
[ 0.103333] pci 0000:00:1d.2: System wakeup disabled by ACPI
[ 0.103333] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
[ 0.103333] pci 0000:00:1d.3: reg 0x20: [io 0xfc00-0xfc1f]
[ 0.103333] pci 0000:00:1d.3: System wakeup disabled by ACPI
[ 0.103333] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
[ 0.103333] pci 0000:00:1d.7: reg 0x10: [mem 0xfdfff000-0xfdfff3ff]
[ 0.103333] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.103379] pci 0000:00:1d.7: System wakeup disabled by ACPI
[ 0.103420] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[ 0.103511] pci 0000:00:1e.0: System wakeup disabled by ACPI
[ 0.103555] pci 0000:00:1f.0: [8086:27b0] type 00 class 0x060100
[ 0.103727] pci 0000:00:1f.1: [8086:27df] type 00 class 0x01018a
[ 0.103741] pci 0000:00:1f.1: reg 0x10: [io 0x0000-0x0007]
[ 0.103750] pci 0000:00:1f.1: reg 0x14: [io 0x0000-0x0003]
[ 0.103760] pci 0000:00:1f.1: reg 0x18: [io 0x0000-0x0007]
[ 0.103769] pci 0000:00:1f.1: reg 0x1c: [io 0x0000-0x0003]
[ 0.103778] pci 0000:00:1f.1: reg 0x20: [io 0xf900-0xf90f]
[ 0.103876] pci 0000:00:1f.2: [8086:27c0] type 00 class 0x01018f
[ 0.103890] pci 0000:00:1f.2: reg 0x10: [io 0xf800-0xf807]
[ 0.103899] pci 0000:00:1f.2: reg 0x14: [io 0xf700-0xf703]
[ 0.103907] pci 0000:00:1f.2: reg 0x18: [io 0xf600-0xf607]
[ 0.103915] pci 0000:00:1f.2: reg 0x1c: [io 0xf500-0xf503]
[ 0.103923] pci 0000:00:1f.2: reg 0x20: [io 0xf400-0xf40f]
[ 0.103932] pci 0000:00:1f.2: reg 0x24: [mem 0xfdffc000-0xfdffc3ff]
[ 0.103961] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.104042] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[ 0.104093] pci 0000:00:1f.3: reg 0x20: [io 0x0500-0x051f]
[ 0.104236] pci 0000:01:00.0: [1002:7181] type 00 class 0x030000
[ 0.104251] pci 0000:01:00.0: reg 0x10: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.104262] pci 0000:01:00.0: reg 0x18: [mem 0xfddf0000-0xfddfffff 64bit]
[ 0.104270] pci 0000:01:00.0: reg 0x20: [io 0xce00-0xceff]
[ 0.104283] pci 0000:01:00.0: reg 0x30: [mem 0xfddc0000-0xfdddffff pref]
[ 0.104314] pci 0000:01:00.0: supports D1 D2
[ 0.104362] pci 0000:01:00.1: [1002:71a1] type 00 class 0x038000
[ 0.104373] pci 0000:01:00.1: reg 0x10: [mem 0xfdde0000-0xfddeffff 64bit]
[ 0.104417] pci 0000:01:00.1: supports D1 D2
[ 0.104457] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.104466] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.104470] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
[ 0.104473] pci 0000:00:01.0: bridge window [mem 0xfdd00000-0xfddfffff]
[ 0.104477] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.104526] pci 0000:02:01.0: [11c1:5811] type 00 class 0x0c0010
[ 0.104543] pci 0000:02:01.0: reg 0x10: [mem 0xfdeff000-0xfdefffff]
[ 0.104616] pci 0000:02:01.0: supports D1 D2
[ 0.104619] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot
[ 0.104672] pci 0000:02:04.0: [1102:0002] type 00 class 0x040100
[ 0.104690] pci 0000:02:04.0: reg 0x10: [io 0xdf00-0xdf1f]
[ 0.104763] pci 0000:02:04.0: supports D1 D2
[ 0.104806] pci 0000:02:04.1: [1102:7002] type 00 class 0x098000
[ 0.104822] pci 0000:02:04.1: reg 0x10: [io 0xde00-0xde07]
[ 0.104895] pci 0000:02:04.1: supports D1 D2
[ 0.104946] pci 0000:02:05.0: [168c:0013] type 00 class 0x020000
[ 0.104964] pci 0000:02:05.0: reg 0x10: [mem 0xfdee0000-0xfdeeffff]
[ 0.105084] pci 0000:02:08.0: [8086:27dc] type 00 class 0x020000
[ 0.105101] pci 0000:02:08.0: reg 0x10: [mem 0xfdefe000-0xfdefefff]
[ 0.105112] pci 0000:02:08.0: reg 0x14: [io 0xdd00-0xdd3f]
[ 0.105176] pci 0000:02:08.0: supports D1 D2
[ 0.105178] pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.105247] pci 0000:00:1e.0: PCI bridge to [bus 02] (subtractive decode)
[ 0.105252] pci 0000:00:1e.0: bridge window [io 0xd000-0xdfff]
[ 0.105256] pci 0000:00:1e.0: bridge window [mem 0xfde00000-0xfdefffff]
[ 0.105262] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
[ 0.105264] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xfffffffff] (subtractive decode)
[ 0.105612] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 *7 9 10 11 12 14 15)
[ 0.105678] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 0.105743] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 7 9 10 11 12 14 15)
[ 0.105807] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 0.105870] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 0.105934] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.105998] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.106063] ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 7 9 10 11 12 14 15)
[ 0.106250] ACPI: Enabled 2 GPEs in block 00 to 1F
[ 0.106258] ACPI: \_SB_.PCI0: notify handler is installed
[ 0.106290] Found 1 acpi root devices
[ 0.106365] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.106365] vgaarb: loaded
[ 0.106365] vgaarb: bridge control possible 0000:01:00.0
[ 0.106365] PCI: Using ACPI for IRQ routing
[ 0.106365] PCI: pci_cache_line_size set to 64 bytes
[ 0.106365] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff]
[ 0.106365] e820: reserve RAM buffer [mem 0x7fedf800-0x7fffffff]
[ 0.106365] NetLabel: Initializing
[ 0.106365] NetLabel: domain hash size = 128
[ 0.106365] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.106365] NetLabel: unlabeled traffic allowed by default
[ 0.106365] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.106365] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.106365] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.106689] Switched to clocksource hpet
[ 0.109999] pnp: PnP ACPI init
[ 0.109999] ACPI: bus type PNP registered
[ 0.113399] system 00:00: [io 0x04d0-0x04d1] has been reserved
[ 0.113403] system 00:00: [io 0x0800-0x087f] has been reserved
[ 0.113406] system 00:00: [io 0x0294-0x0297] has been reserved
[ 0.113408] system 00:00: [io 0x0880-0x088f] has been reserved
[ 0.113413] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.113426] pnp 00:01: [dma 4]
[ 0.113459] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.113547] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.113597] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.113626] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.113664] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.113790] pnp 00:06: Plug and Play ACPI device, IDs PNP0f13 (active)
[ 0.113848] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.113911] system 00:08: [io 0x0400-0x04bf] has been reserved
[ 0.113915] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.113958] pnp 00:09: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.114177] system 00:0a: [mem 0xf0000000-0xf3ffffff] has been reserved
[ 0.114182] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.114356] system 00:0b: [mem 0x000cf400-0x000cffff] has been reserved
[ 0.114359] system 00:0b: [mem 0x000f0000-0x000f7fff] could not be reserved
[ 0.114362] system 00:0b: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.114365] system 00:0b: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.114368] system 00:0b: [mem 0xfed00000-0xfed000ff] has been reserved
[ 0.114371] system 00:0b: [mem 0x7fee0000-0x7fefffff] could not be reserved
[ 0.114374] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.114377] system 00:0b: [mem 0x00100000-0x7fedffff] could not be reserved
[ 0.114380] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.114382] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.114385] system 00:0b: [mem 0xffb00000-0xffb7ffff] has been reserved
[ 0.114388] system 00:0b: [mem 0xfff00000-0xffffffff] has been reserved
[ 0.114390] system 00:0b: [mem 0x000e0000-0x000effff] has been reserved
[ 0.114394] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.114404] pnp: PnP ACPI: found 12 devices
[ 0.114405] ACPI: bus type PNP unregistered
[ 0.120198] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.120198] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
[ 0.120198] pci 0000:00:01.0: bridge window [mem 0xfdd00000-0xfddfffff]
[ 0.120198] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.120198] pci 0000:00:1e.0: PCI bridge to [bus 02]
[ 0.120198] pci 0000:00:1e.0: bridge window [io 0xd000-0xdfff]
[ 0.120198] pci 0000:00:1e.0: bridge window [mem 0xfde00000-0xfdefffff]
[ 0.120198] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.120198] pci_bus 0000:00: resource 5 [mem 0x00000000-0xfffffffff]
[ 0.120198] pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
[ 0.120198] pci_bus 0000:01: resource 1 [mem 0xfdd00000-0xfddfffff]
[ 0.120198] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.120198] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
[ 0.120198] pci_bus 0000:02: resource 1 [mem 0xfde00000-0xfdefffff]
[ 0.120198] pci_bus 0000:02: resource 4 [io 0x0000-0xffff]
[ 0.120198] pci_bus 0000:02: resource 5 [mem 0x00000000-0xfffffffff]
[ 0.120198] NET: Registered protocol family 2
[ 0.120198] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.120198] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.120198] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.120198] TCP: reno registered
[ 0.120198] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.120198] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.120198] NET: Registered protocol family 1
[ 0.120198] pci 0000:01:00.0: Boot video device
[ 0.120198] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
[ 0.120198] PCI: CLS 32 bytes, default 64
[ 0.120198] Unpacking initramfs...
[ 0.191296] Freeing initrd memory: 3084K (ffff8800379ea000 - ffff880037ced000)
[ 0.191480] Scanning for low memory corruption every 60 seconds
[ 0.191882] audit: initializing netlink socket (disabled)
[ 0.191902] type=2000 audit(1396428835.189:1): initialized
[ 0.206560] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.208164] zbud: loaded
[ 0.208353] VFS: Disk quotas dquot_6.5.2
[ 0.208404] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.208606] msgmni has been set to 4004
[ 0.208673] Key type big_key registered
[ 0.208929] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.208971] io scheduler noop registered
[ 0.208973] io scheduler deadline registered
[ 0.209007] io scheduler cfq registered (default)
[ 0.209208] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 0.209282] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.209302] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.209360] vesafb: mode is 1400x1050x32, linelength=5632, pages=0
[ 0.209362] vesafb: scrolling: redraw
[ 0.209364] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
[ 0.209895] vesafb: framebuffer at 0xe0000000, mapped to 0xffffc90004400000, using 5824k, total 5824k
[ 0.265490] Console: switching to colour frame buffer device 175x65
[ 0.320013] fb0: VESA VGA frame buffer device
[ 0.320013] intel_idle: does not run on family 6 model 15
[ 0.320013] GHES: HEST is not enabled!
[ 0.320771] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.321201] Linux agpgart interface v0.103
[ 0.321270] rtc_cmos 00:03: RTC can wake from S4
[ 0.321402] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.321430] rtc_cmos 00:03: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.321540] drop_monitor: Initializing network drop monitor service
[ 0.321607] TCP: cubic registered
[ 0.321718] NET: Registered protocol family 10
[ 0.321912] NET: Registered protocol family 17
[ 0.321924] Key type dns_resolver registered
[ 0.322165] registered taskstats version 1
[ 0.322582] Magic number: 10:872:926
[ 0.322659] rtc_cmos 00:03: setting system clock to 2014-04-02 08:54:05 UTC (1396428845)
[ 0.322694] PM: Hibernation image not present or could not be loaded.
[ 0.324137] Freeing unused kernel memory: 1124K (ffffffff818d3000 - ffffffff819ec000)
[ 0.324139] Write protecting the kernel read-only data: 8192k
[ 0.326967] Freeing unused kernel memory: 860K (ffff880001529000 - ffff880001600000)
[ 0.327354] Freeing unused kernel memory: 372K (ffff8800017a3000 - ffff880001800000)
[ 0.335950] random: systemd-tmpfile urandom read with 1 bits of entropy available
[ 0.337560] systemd-udevd[46]: starting version 212
[ 0.357062] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.360689] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.360743] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.364815] ACPI: bus type USB registered
[ 0.364858] usbcore: registered new interface driver usbfs
[ 0.364871] usbcore: registered new interface driver hub
[ 0.367300] usbcore: registered new device driver usb
[ 0.367497] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.367497] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.367497] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.369227] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 0.369272] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ff00
[ 0.370097] hub 1-0:1.0: USB hub found
[ 0.370108] hub 1-0:1.0: 2 ports detected
[ 0.370356] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.370364] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 0.370398] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fe00
[ 0.370561] hub 2-0:1.0: USB hub found
[ 0.370570] hub 2-0:1.0: 2 ports detected
[ 0.370923] ehci-pci: EHCI PCI platform driver
[ 0.371254] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.371263] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 0.371299] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fd00
[ 0.371479] hub 3-0:1.0: USB hub found
[ 0.371489] hub 3-0:1.0: 2 ports detected
[ 0.371685] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 0.371695] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 0.371731] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fc00
[ 0.371759] SCSI subsystem initialized
[ 0.372294] hub 4-0:1.0: USB hub found
[ 0.372721] hub 4-0:1.0: 2 ports detected
[ 0.373567] ehci-pci 0000:00:1d.7: EHCI Host Controller
[ 0.373575] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 0.380063] ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
[ 0.380074] ehci-pci 0000:00:1d.7: irq 23, io mem 0xfdfff000
[ 0.380372] libata version 3.00 loaded.
[ 0.392071] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.392288] hub 5-0:1.0: USB hub found
[ 0.392298] hub 5-0:1.0: 8 ports detected
[ 0.413670] hub 1-0:1.0: USB hub found
[ 0.413685] hub 1-0:1.0: 2 ports detected
[ 0.418065] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.428408] firewire_ohci 0000:02:01.0: added OHCI v1.0 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
[ 0.444932] hub 2-0:1.0: USB hub found
[ 0.444946] hub 2-0:1.0: 2 ports detected
[ 0.475276] hub 3-0:1.0: USB hub found
[ 0.475295] hub 3-0:1.0: 2 ports detected
[ 0.498283] hub 4-0:1.0: USB hub found
[ 0.498296] hub 4-0:1.0: 2 ports detected
[ 0.498418] ata_piix 0000:00:1f.1: version 2.13
[ 0.499273] scsi0 : ata_piix
[ 0.499357] scsi1 : ata_piix
[ 0.499402] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf900 irq 14
[ 0.499404] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf908 irq 15
[ 0.499515] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 0.499556] ata2: port disabled--ignoring
[ 0.500252] scsi2 : ata_piix
[ 0.500325] scsi3 : ata_piix
[ 0.500368] ata3: SATA max UDMA/133 cmd 0xf800 ctl 0xf700 bmdma 0xf400 irq 19
[ 0.500371] ata4: SATA max UDMA/133 cmd 0xf600 ctl 0xf500 bmdma 0xf408 irq 19
[ 0.699056] ata4.01: NODEV after polling detection
[ 0.705789] ata4.00: ATAPI: HL-DT-STDVDRRW GSA-H30L, S755, max UDMA/33
[ 0.705879] ata1.00: ATA-7: Hitachi HDT725032VLAT80, V54OA42A, max UDMA/133
[ 0.705882] ata1.00: 625142448 sectors, multi 16: LBA48
[ 0.705886] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 0.718854] ata4.00: configured for UDMA/33
[ 0.721647] ata1.00: configured for UDMA/33
[ 0.721797] scsi 0:0:0:0: Direct-Access ATA Hitachi HDT72503 V54O PQ: 0 ANSI: 5
[ 0.725607] ata3.00: ATA-8: SAMSUNG HD320KJ, CP100-10, max UDMA7
[ 0.725612] ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 0.734331] ata3.00: configured for UDMA/133
[ 0.734447] scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD320KJ CP10 PQ: 0 ANSI: 5
[ 0.736470] scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRRW GSA-H30L S755 PQ: 0 ANSI: 5
[ 0.739885] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 0.739947] sd 0:0:0:0: [sda] Write Protect is off
[ 0.739950] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.739977] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.740339] sd 2:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 0.740397] sd 2:0:0:0: [sdb] Write Protect is off
[ 0.740400] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 0.740426] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.743908] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 0.743912] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 0.744145] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 0.748725] sdb: sdb1 sdb2
[ 0.749036] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 0.752217] usb 5-6: new high-speed USB device number 2 using ehci-pci
[ 0.778689] sda: sda1 sda2 sda3 sda4
[ 0.779129] sd 0:0:0:0: [sda] Attached SCSI disk
[ 0.929217] firewire_core 0000:02:01.0: created device fw0: GUID 0011d800013adf24, S400
[ 1.006684] usb 5-7: new high-speed USB device number 3 using ehci-pci
[ 1.173252] usb-storage 5-7:1.0: USB Mass Storage device detected
[ 1.173332] scsi4 : usb-storage 5-7:1.0
[ 1.173427] usbcore: registered new interface driver usb-storage
[ 1.197356] tsc: Refined TSC clocksource calibration: 2133.939 MHz
[ 1.616813] EXT4-fs (sda2): mounting ext3 file system using the ext4 subsystem
[ 1.624951] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 1.920203] random: nonblocking pool is initialized
[ 2.247183] Switched to clocksource tsc
[ 2.253827] scsi 4:0:0:0: Direct-Access Generic- Compact Flash 1.00 PQ: 0 ANSI: 0 CCS
[ 2.260322] scsi 4:0:0:1: Direct-Access Generic- SM/xD-Picture 1.00 PQ: 0 ANSI: 0 CCS
[ 2.266946] scsi 4:0:0:2: Direct-Access Generic- SD/MMC 1.00 PQ: 0 ANSI: 0 CCS
[ 2.273571] scsi 4:0:0:3: Direct-Access Generic- MS/MS-Pro 1.00 PQ: 0 ANSI: 0 CCS
[ 2.280559] sd 4:0:0:0: [sdc] Attached SCSI removable disk
[ 2.281310] sd 4:0:0:1: [sdd] Attached SCSI removable disk
[ 2.282059] sd 4:0:0:2: [sde] Attached SCSI removable disk
[ 2.282809] sd 4:0:0:3: [sdf] Attached SCSI removable disk
[ 2.498874] systemd[1]: systemd 212 running in system mode. (+PAM -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ +SECCOMP -APPARMOR)
[ 2.499029] systemd[1]: Detected architecture 'x86-64'.
[ 2.499095] systemd[1]: No hostname configured.
[ 2.499100] systemd[1]: Set hostname to <localhost>.
[ 3.019084] systemd[1]: Configuration file /etc/systemd/system/netctl@ethernet\x2dstatic.service is marked world-inaccessible. This has no effect as configuration data is accessible via APIs without restrictions. Proceeding anyway.
[ 3.052564] systemd[1]: Configuration file /etc/systemd/system/netctl@my\x2dnetwork.service is marked world-inaccessible. This has no effect as configuration data is accessible via APIs without restrictions. Proceeding anyway.
[ 3.168175] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 3.168523] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 3.168587] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 3.168600] systemd[1]: Expecting device sys-subsystem-net-devices-enp2s8.device...
[ 3.168617] systemd[1]: Starting Remote File Systems.
[ 3.168629] systemd[1]: Reached target Remote File Systems.
[ 3.168639] systemd[1]: Expecting device sys-subsystem-net-devices-wlp2s5.device...
[ 3.168655] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 3.168691] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 3.168701] systemd[1]: Starting Paths.
[ 3.168712] systemd[1]: Reached target Paths.
[ 3.168722] systemd[1]: Starting Encrypted Volumes.
[ 3.168732] systemd[1]: Reached target Encrypted Volumes.
[ 3.168756] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 3.168851] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 3.168865] systemd[1]: Expecting device dev-sda4.device...
[ 3.168877] systemd[1]: Expecting device dev-disk-by\x2duuid-8e743759\x2dc6f4\x2d4e8f\x2dae25\x2d2c24a8cba618.device...
[ 3.168890] systemd[1]: Expecting device dev-disk-by\x2duuid-c96171f5\x2d9704\x2d4abf\x2d84ae\x2d2c4f78252a60.device...
[ 3.168900] systemd[1]: Expecting device dev-disk-by\x2duuid-12EC23D6EC23B341.device...
[ 3.168911] systemd[1]: Starting Root Slice.
[ 3.175997] systemd[1]: Created slice Root Slice.
[ 3.176010] systemd[1]: Starting Delayed Shutdown Socket.
[ 3.176047] systemd[1]: Listening on Delayed Shutdown Socket.
[ 3.176058] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 3.176087] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 3.176098] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 3.176119] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 3.176133] systemd[1]: Starting udev Kernel Socket.
[ 3.176155] systemd[1]: Listening on udev Kernel Socket.
[ 3.176169] systemd[1]: Starting udev Control Socket.
[ 3.176193] systemd[1]: Listening on udev Control Socket.
[ 3.176203] systemd[1]: Starting LVM2 metadata daemon socket.
[ 3.176232] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 3.176243] systemd[1]: Starting User and Session Slice.
[ 3.176438] systemd[1]: Created slice User and Session Slice.
[ 3.176452] systemd[1]: Starting Journal Socket.
[ 3.176501] systemd[1]: Listening on Journal Socket.
[ 3.176518] systemd[1]: Starting System Slice.
[ 3.176712] systemd[1]: Created slice System Slice.
[ 3.176728] systemd[1]: Started File System Check on Root Device.
[ 3.176738] systemd[1]: Starting system-systemd\x2dfsck.slice.
[ 3.176940] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 3.176954] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 3.212380] systemd[1]: Started Load Kernel Modules.
[ 3.252481] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 3.253015] systemd[1]: Starting udev Coldplug all Devices...
[ 3.253553] systemd[1]: Mounted FUSE Control File System.
[ 3.253577] systemd[1]: Mounting Configuration File System...
[ 3.254197] systemd[1]: Starting Setup Virtual Console...
[ 3.254782] systemd[1]: Mounting Debug File System...
[ 3.255307] systemd[1]: Mounting Huge Pages File System...
[ 3.285128] systemd[1]: Starting Apply Kernel Variables...
[ 3.285663] systemd[1]: Starting system-netctl.slice.
[ 3.285916] systemd[1]: Created slice system-netctl.slice.
[ 3.285940] systemd[1]: Starting system-getty.slice.
[ 3.286240] systemd[1]: Created slice system-getty.slice.
[ 3.286797] systemd[1]: Started Set Up Additional Binary Formats.
[ 3.286822] systemd[1]: Mounting POSIX Message Queue File System...
[ 3.287292] systemd[1]: Starting Journal Service...
[ 3.287880] systemd[1]: Started Journal Service.
[ 4.510133] EXT4-fs (sda2): re-mounted. Opts: data=ordered
[ 4.568872] systemd-udevd[136]: starting version 212
[ 5.479614] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 5.479621] ACPI: Power Button [PWRB]
[ 5.479693] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 5.479697] ACPI: Power Button [PWRF]
[ 5.490126] thermal LNXTHERM:00: registered as thermal_zone0
[ 5.490129] ACPI: Thermal Zone [THRM] (19 C)
[ 5.629665] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PM2S 1 (20131115/utaddress-251)
[ 5.629673] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PM1K 2 (20131115/utaddress-251)
[ 5.629677] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \GPE1 3 (20131115/utaddress-251)
[ 5.629682] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.629685] ACPI Warning: 0x00000000000004b0-0x00000000000004bf SystemIO conflicts with Region \GPO2 1 (20131115/utaddress-251)
[ 5.629689] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.629691] ACPI Warning: 0x0000000000000480-0x00000000000004af SystemIO conflicts with Region \GPIV 1 (20131115/utaddress-251)
[ 5.629695] ACPI Warning: 0x0000000000000480-0x00000000000004af SystemIO conflicts with Region \GPO_ 2 (20131115/utaddress-251)
[ 5.629699] ACPI Warning: 0x0000000000000480-0x00000000000004af SystemIO conflicts with Region \PALD 3 (20131115/utaddress-251)
[ 5.629703] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.629705] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 5.639853] leds_ss4200: no LED devices found
[ 5.687416] ACPI: Fan [FAN] (on)
[ 5.708079] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 5.931908] cfg80211: Calling CRDA to update world regulatory domain
[ 6.109750] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 6.109754] e100: Copyright(c) 1999-2006 Intel Corporation
[ 6.133562] e100 0000:02:08.0 eth0: addr 0xfdefe000, irq 20, MAC addr 00:1a:92:de:71:43
[ 6.410441] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
[ 6.599698] gameport gameport0: EMU10K1 is pci0000:02:04.1/gameport0, io 0xde00, speed 980kHz
[ 6.659464] [drm] Initialized drm 1.1.0 20060810
[ 6.722900] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 6.926377] iTCO_vendor_support: vendor-support=0
[ 6.963443] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 6.963473] iTCO_wdt: Found a ICH7DH TCO device (Version=2, TCOBASE=0x0460)
[ 6.963581] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 7.184227] Adding 4286784k swap on /dev/sda4. Priority:-1 extents:1 across:4286784k FS
[ 7.195727] microcode: CPU0 sig=0x6f6, pf=0x1, revision=0xc6
[ 7.263090] rtl8192cu: Chip version 0x11
[ 7.334816] ath5k 0000:02:05.0: registered as 'phy1'
[ 7.352471] rtl8192cu: MAC address: 80:1f:02:af:89:eb
[ 7.352477] rtl8192cu: Board Type 0
[ 7.352718] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 7.352752] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[ 7.352808] usbcore: registered new interface driver rtl8192cu
[ 7.445824] [drm] radeon kernel modesetting enabled.
[ 7.445878] checking generic (e0000000 5b0000) vs hw (e0000000 10000000)
[ 7.445880] fb: conflicting fb hw usage radeondrmfb vs VESA VGA - removing generic driver
[ 7.316873] systemd-udevd[150]: renamed network interface eth0 to enp2s8
[ 7.445900] Console: switching
[ 7.445902] to colour dummy device 80x25
[ 7.446670] [drm] initializing kernel modesetting (RV515 0x1002:0x7181 0x1462:0x0400).
[ 7.446689] [drm] register mmio base: 0xFDDF0000
[ 7.446691] [drm] register mmio size: 65536
[ 7.446807] ATOM BIOS: 113
[ 7.446821] [drm] Generation 2 PCI interface, using max accessible memory
[ 7.446827] radeon 0000:01:00.0: VRAM: 512M 0x0000000000000000 - 0x000000001FFFFFFF (512M used)
[ 7.446830] radeon 0000:01:00.0: GTT: 512M 0x0000000020000000 - 0x000000003FFFFFFF
[ 7.446845] [drm] Detected VRAM RAM=512M, BAR=256M
[ 7.446847] [drm] RAM width 128bits DDR
[ 7.446916] [TTM] Zone kernel: Available graphics memory: 1026428 kiB
[ 7.446918] [TTM] Initializing pool allocator
[ 7.446923] [TTM] Initializing DMA pool allocator
[ 7.446942] [drm] radeon: 512M of VRAM memory ready
[ 7.446944] [drm] radeon: 512M of GTT memory ready.
[ 7.446965] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 7.458262] [drm] radeon: 1 quad pipes, 1 z pipes initialized.
[ 7.459147] [drm] PCIE GART of 512M enabled (table at 0x0000000000040000).
[ 7.459171] radeon 0000:01:00.0: WB enabled
[ 7.459176] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000020000000 and cpu addr 0xffff88007bb31000
[ 7.459179] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 7.459180] [drm] Driver supports precise vblank timestamp query.
[ 7.459192] [drm] radeon: irq initialized.
[ 7.459208] [drm] Loading R500 Microcode
[ 7.476935] platform microcode: Direct firmware load failed with error -2
[ 7.476939] platform microcode: Falling back to user helper
[ 7.477387] microcode: CPU1 sig=0x6f6, pf=0x1, revision=0xc6
[ 7.477402] platform microcode: Direct firmware load failed with error -2
[ 7.477405] platform microcode: Falling back to user helper
[ 7.477982] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[ 7.503453] [drm] radeon: ring at 0x0000000020001000
[ 7.503490] [drm] ring test succeeded in 6 usecs
[ 7.503671] [drm] ib test succeeded in 0 usecs
[ 7.503948] [drm] Radeon Display Connectors
[ 7.503950] [drm] Connector 0:
[ 7.503951] [drm] DVI-I-1
[ 7.503953] [drm] HPD2
[ 7.503955] [drm] DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
[ 7.503957] [drm] Encoders:
[ 7.503958] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 7.503960] [drm] DFP3: INTERNAL_LVTM1
[ 7.503961] [drm] Connector 1:
[ 7.503963] [drm] SVIDEO-1
[ 7.503964] [drm] Encoders:
[ 7.503965] [drm] TV1: INTERNAL_KLDSCP_DAC2
[ 7.503967] [drm] Connector 2:
[ 7.503968] [drm] DVI-I-2
[ 7.503969] [drm] HPD1
[ 7.503971] [drm] DDC: 0x7e50 0x7e50 0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c 0x7e5c
[ 7.503973] [drm] Encoders:
[ 7.503974] [drm] CRT2: INTERNAL_KLDSCP_DAC2
[ 7.503976] [drm] DFP1: INTERNAL_KLDSCP_TMDS1
[ 7.583351] [drm] fb mappable at 0xE00C0000
[ 7.583351] [drm] vram apper at 0xE0000000
[ 7.583351] [drm] size 7258112
[ 7.583351] [drm] fb depth is 24
[ 7.583351] [drm] pitch is 6912
[ 7.583719] fbcon: radeondrmfb (fb0) is primary device
[ 7.600235] Console: switching to colour frame buffer device 210x65
[ 7.605874] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[ 7.605877] radeon 0000:01:00.0: registered panic notifier
[ 7.605883] [drm] Initialized radeon 2.36.0 20080528 for 0000:01:00.0 on minor 0
[ 7.625781] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 7.626479] rtlwifi: wireless switch is on
[ 7.642639] fuse init (API version 7.22)
[ 7.647140] ath: EEPROM regdomain: 0x0
[ 7.647144] ath: EEPROM indicates default country code should be used
[ 7.647146] ath: doing EEPROM country->regdmn map search
[ 7.647149] ath: country maps to regdmn code: 0x3a
[ 7.647151] ath: Country alpha2 being used: US
[ 7.647153] ath: Regpair used: 0x3a
[ 7.647274] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 7.647537] ath5k: phy1: Atheros AR5212 chip found (MAC: 0x56, PHY: 0x41)
[ 7.647540] ath5k: phy1: RF5111 5GHz radio found (0x17)
[ 7.647543] ath5k: phy1: RF2111 2GHz radio found (0x23)
[ 7.709874] systemd-udevd[143]: renamed network interface wlan1 to wlp2s5
[ 8.136233] systemd-udevd[141]: renamed network interface wlan0 to wlp0s29f7u6
[ 8.322562] coretemp coretemp.0: Using relative temperature scale!
[ 8.322706] coretemp coretemp.0: Using relative temperature scale!
[ 8.594743] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input5
[ 8.638575] mousedev: PS/2 mouse device common for all mice
[ 9.284691] EXT4-fs (sda3): mounting ext3 file system using the ext4 subsystem
[ 9.328865] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: data=ordered
[ 10.357627] IPv6: ADDRCONF(NETDEV_UP): enp2s8: link is not ready
[ 10.363499] e100 0000:02:08.0 enp2s8: NIC Link is Up 100 Mbps Full Duplex
[ 10.363772] IPv6: ADDRCONF(NETDEV_CHANGE): enp2s8: link becomes ready
[ 10.865860] systemd-journald[119]: Received request to flush runtime journal from PID 1
[ 11.002834] rtl8192cu: MAC auto ON okay!
[ 11.035475] rtl8192cu: Tx queue select: 0x05
[ 11.407281] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
[ 12.592937] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
[ 12.617024] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
[ 12.654273] wlp0s29f7u6: authenticated
[ 12.659239] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
[ 12.663526] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
[ 12.663558] wlp0s29f7u6: associated
[ 12.663598] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
[ 216.768500] perf samples too long (2503 > 2500), lowering kernel.perf_event_max_sample_rate to 50100
[ 295.526133] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
[ 295.538508] cfg80211: Calling CRDA for country: US
[ 295.779488] rtl8192cu: MAC auto ON okay!
[ 295.813132] rtl8192cu: Tx queue select: 0x05
[ 296.188680] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
[ 297.158587] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
[ 297.171430] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
[ 297.181575] wlp0s29f7u6: authenticated
[ 297.185043] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
[ 297.198798] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
[ 297.198839] wlp0s29f7u6: associated
[ 297.198885] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
[ 466.957760] perf samples too long (4993 > 4990), lowering kernel.perf_event_max_sample_rate to 25200
[ 653.237523] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
[ 653.252189] cfg80211: Calling CRDA for country: GB
[ 653.492515] rtl8192cu: MAC auto ON okay!
[ 653.526155] rtl8192cu: Tx queue select: 0x05
[ 653.902071] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
[ 654.830321] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
[ 654.843456] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
[ 654.863972] wlp0s29f7u6: authenticated
[ 654.867473] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
[ 654.879214] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
[ 654.879258] wlp0s29f7u6: associated
[ 654.879319] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
[ 845.720733] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
[ 845.733072] cfg80211: Calling CRDA to update world regulatory domain
[ 845.972288] rtl8192cu: MAC auto ON okay!
[ 846.005180] rtl8192cu: Tx queue select: 0x05
[ 846.376969] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
[ 847.303644] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
[ 847.316223] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
[ 847.341107] wlp0s29f7u6: authenticated
[ 847.345443] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
[ 847.369345] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
[ 847.369380] wlp0s29f7u6: associated
[ 847.369422] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
[ 1165.243225] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
[ 1165.255458] cfg80211: Calling CRDA for country: GB
[ 1165.501950] rtl8192cu: MAC auto ON okay!
[ 1165.534590] rtl8192cu: Tx queue select: 0x05
[ 1165.906506] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
[ 1166.922571] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
[ 1166.935133] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
[ 1166.962884] wlp0s29f7u6: authenticated
[ 1166.963550] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
[ 1166.969384] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
[ 1166.969418] wlp0s29f7u6: associated
[ 1166.969455] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
[ 1317.334883] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
[ 1317.347568] cfg80211: Calling CRDA to update world regulatory domain
[ 1317.593153] rtl8192cu: MAC auto ON okay!
[ 1317.625922] rtl8192cu: Tx queue select: 0x05
[ 1318.002339] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
[ 1318.943694] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
[ 1318.959587] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
[ 1318.961335] wlp0s29f7u6: authenticated
[ 1318.965144] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
[ 1318.988340] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
[ 1318.988376] wlp0s29f7u6: associated
[ 1318.988421] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
[ 1469.086853] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
[ 1469.099248] cfg80211: Calling CRDA to update world regulatory domain
[ 1469.337346] rtl8192cu: MAC auto ON okay!
[ 1469.370119] rtl8192cu: Tx queue select: 0x05
[ 1469.742158] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
[ 1470.673984] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
[ 1470.686540] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
[ 1470.691410] wlp0s29f7u6: authenticated
[ 1470.693241] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
[ 1470.702651] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
[ 1470.702687] wlp0s29f7u6: associated
[ 1470.702728] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
[ 1680.753182] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
[ 1680.765752] cfg80211: Calling CRDA for country: GB
[ 1680.998495] rtl8192cu: MAC auto ON okay!
[ 1681.031255] rtl8192cu: Tx queue select: 0x05
[ 1681.406799] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
[ 1682.318347] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
[ 1682.330930] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
[ 1682.342673] wlp0s29f7u6: authenticated
[ 1682.343689] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
[ 1682.350924] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
[ 1682.350956] wlp0s29f7u6: associated
[ 1682.350994] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
[ 2206.980860] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
[ 2206.993170] cfg80211: Calling CRDA to update world regulatory domain
[ 2207.227511] rtl8192cu: MAC auto ON okay!
[ 2207.260157] rtl8192cu: Tx queue select: 0x05
[ 2207.631823] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
[ 2208.565086] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
[ 2208.577695] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
[ 2208.585581] wlp0s29f7u6: authenticated
[ 2208.587355] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
[ 2208.616071] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
[ 2208.616112] wlp0s29f7u6: associated
[ 2208.616155] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
[ 2504.014135] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
[ 2504.026462] cfg80211: Calling CRDA to update world regulatory domain
[ 2504.273688] rtl8192cu: MAC auto ON okay!
[ 2504.309828] rtl8192cu: Tx queue select: 0x05
[ 2504.702760] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
[ 2505.627571] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
[ 2505.640510] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
[ 2505.649754] wlp0s29f7u6: authenticated
[ 2505.650508] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
[ 2505.680782] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
[ 2505.680831] wlp0s29f7u6: associated
[ 2505.680887] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
[ 2948.553142] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
[ 2948.565823] cfg80211: Calling CRDA for country: GB
[ 2948.814051] rtl8192cu: MAC auto ON okay!
[ 2948.846690] rtl8192cu: Tx queue select: 0x05
[ 2949.220485] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
[ 2950.173570] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
[ 2950.186113] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
[ 2950.190241] wlp0s29f7u6: authenticated
If there is anything else I can provide that may help please ask, this has been driving me mad for days now!

Looks like a driver bug. You could try multiple things, as a start:
- switch channel
- toggle encryption
- different usb port

HP 6510 AIO Printer

HP can make my New Year a marvalous one by developing an OCR app that is compatable with the HP 6510 Printer. What is OCR you ask? Well, OCR stands for Optical Charcter Recognition and what that does is; it enables you to scan a form and have the ability to write or fill in the blanks on the form.

Hi,
Please use your OTHER post:
http://h30434.www3.hp.com/t5/ePrint-Print-Apps-Mobile-Printing-and-ePrintCenter/OCR-Apps/m-p/2283671
Thanks.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Having a problem with wireless connection. On my Windows XP 32 bit system and a 6510 printer, initi

On my Dell Latitude D620, Windows XP 32 bit system and my 6510 printer wireless connection (Linksys EA4500) , everything works fine after the computer is booted. After a period of time (usually overnight), I lose connection to the printer (the scanner icon with a red x is shown on my Windows task bar and I can't print. Ran Windows Fix and the HP fix programs. The only thing that solves it is to reboot the computer. A second symptom is that my IE8 stops connecting to the internet at the same time (gives a 'waiting for' response that never changes). Firefox still connects OK when this is happening. So I suspect the problem isn't with the printer, but with my Windows set up. It is a fresh XP SP3 install (hard drive crashed, but it happened before also). I reset IE, checked my proxy, no malware, happens with or without firewalls and security programs.
Hoping that someone else has run into this problem. Been all over Google, and the IE doesn't work / Firefox works is fairly common, but none of the fixes helps.

If you want you can reload Firefox 4.0 or the last "old" version is 3.6.16 and is available here:
http://www.mozilla.com/en-US/firefox/all-older.html
Just reinstall your choice of FF. The bookmarks are in a different directory and are NOT overwritten. Some of the Add-ons that worked in 3.6 DO NOT work with 4.0, pay attention and head any warnings when you start 4.0.
I had to disable extensions: Flashblock and WOT
Firefox SafeMode? - A troubleshooting mode.
1.You can open the Firefox 4.0 SafeMode by holding the Shft key when you use the Firefox desktop or Start menu shortcut.
To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before using the Firefox shortcut to open it again.
For more help, see this: http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes
Hope this helps you out.
Feedback is appreciated especially if this helps you out.

PRINTER 6510 e-all in on. photo product core exe has stopped working?lang=en

i installed the 6510 all in one printer, it works great but the photo creation has a message that is (photo product core exe has stopped working). that should i do to fix it?
This question was solved.
View Solution.

Hi Puhu.
Please contact our customer support team at [email protected] They can help get you printing again.
Thanks for writing,
RocketLife
RocketLife, developer of HP Photo Creations
» Visit the HP Photo Creations Facebook page — news, tips, and inspiration
» See the HP Photo Creations video tours — cool tips in under 2 minutes
» Contact Customer Support — get answers from the experts

I have an iPad mini and an iPad 2. I can print email to my HP 6510 from the mini, but NOT from the iPad 2. Both are on the same wi-fi network. I have tried everything I can do including unplugging everything, restarting, etc. Can anyone help?

I have an iPad mini and an iPad 2. I can print email to my HP 6510 from the mini, but NOT from the iPad 2. Both are on the same wi-fi network. I have tried everything I can do including unplugging everything, restarting, etc. Can anyone help?

Thanks so much! My grandaughters played games on the iPad over Xmas and one of their moms said shed restricted their access! Guess they forgot to enable again. Thank you again! Karla

How do i print from internet in black ink only with my mac osx 10.5 using hp 6510 all in one

i can not get my IMAC OS X 10.5 to print only black ink from the internet, using my new HP 6510 all in one printer. HELP
This question was solved.
View Solution.

With pleasure!
Great to know it worked for you
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

HP 6510 won't print black on page (dumps it on the right, image inside)

Hello everybody,
For the past couple of days my HP 6510 printer no longer prints black ink on the page.
I've already searched the forums to look for an answer and have tried pretty much everything, as well as going through the whole troubleshooting page here:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=uk&lc=en&docname=c02907259
The printer still does not work properly. The CMY inks still work fine, and there was never a problem with any of them.
I had noticed that the estimated ink levels were going down for the black ink so I knew that it was actually releasing the ink, just not on the paper. (although I do get the two light grey bars when doing the clean printhead test, but no black.)
I noticed that there was a lot of ink on the inside of the right side of the printer, just under where the print cartridges are located when they are not in use, just a big blob of black, although I later found out that it was actually all four inks - mostly black though.
I place a little piece of card in there and printed a short document to see how much of each ink was being released, and this is what I found.
(Open in new tab for full size)
I also bought a new black cartridge to see if the problem would go away and it doesn't. The fact that nothing seems to be 'broken' and that the other inks all work fine I am convinced this is a software issue and that the printer hardware is not damaged.
Printer Driver: 09.84.00.1173
OS: Windows 8.1 64bit
Connecting over Wifi
Does anybody have a fix for this?

There seems to be nothing unusual about the printer other than the missing black ink.
The vents are not clogged, I even got a new black ink to see if that would fix it, unfortunately it didn't.
As you can see in the picture I added to my original post, black ink is being released, just not on the page itself.
I've tried cleaning the print head several times from the tool menu, but this still hasn't fixed the problem with my black ink, and the alignment tool fails every time.
I've tried to manually clean the printhead and hard reset the printer but that didn't fix anything either.
Is there an older driver for the printer that maybe I could try and see if it works?

How to connect 6510 printer to ID

I have a wireless 6510 printer now need to know how I can connect IPAD so I can print from the IPAD

Hi @lmadubuque
Welcome to the HP Support Forums. I see that you would like to learn how to setup your Photosmart 6510 printer so you can print from your iPad.
Please start by connecting the printer to your wireless network. This can be easily accomplished from the front panel of the printer. If you are unsure how to do this the steps can be found in the Photosmart 6510 User Guide on page 37, in the section titled “To connect the product with the Wireless Setup Wizard”.
Once the printer is connected to your wireless network and if your router supports Bonjour communication you should now be able to print using Apple’s AirPrint feature. I’ve included 2 different documents on using Apple’s AirPrint with HP printers. The first one is Printing from Your Apple Device with Non-Web-Enabled Printers (No Apple AirPrint or HP ePrint Suppor... and the second one is How to Use Apple's AirPrint Over a Wireless Network.
If you want more options than what is available with AirPrint (see Apple’s AirPrint Basics document) you can download and install HP’s ePrint Mobile app. I’ve included the HP ePrint Mobile App FAQs document for reference.
If you would like to scan with your iPad please download HP’s All-in-One Printer Remote app. The app will allow customers, with a supported printer, to scan documents to their iPad. I’ve included the HP All-in-One Printer Remote Mobile App FAQs document for reference.
If you would like to setup HP’s ePrint feature, the first step would be to Get the Printer’s Claim Code. Once you have the printer’s claim code you would add it to your HP ePrintCenter or HP Connected account (HP Connected has only been rolled out to the USA, the UK, Germany and France), and then you have the option to Customize the ePrint Email Address. I’ve also included the Getting Started with ePrint document which will explain how to print with ePrint and also has an FAQ section.
If things go awry, please let me know at which step things went hairy and if you received any error messages.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Can not connect printer HP photosmart all in one 6510 with my windows 7 home edition PC

Stuck! Please help. I'vre uninstalled and reinstalled several times: restore PC to previous working time; checked all passwords and IP addresses. Do wireless connection (home group) network - says it can't connect up by wireless, evenb though it says printer is connected up to internet as is PC. USB connection it jams on the drawing of the ethernet connection. PC does not accept updates-they all fail. Last week I had no such problems. Rolfus
This question was solved.
View Solution.

Hi Rolfus,
Welcome to the HP Forums!
I understand that your HP Photosmart 6510 will not print with your Windows 7 PC.
I would suggest going through this guide. Printer Does Not Maintain Wireless Connection.
Hope this helps, and have a good day.
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Edimax & 6510

Similar Messages

Maybe you are looking for