Edit to tape chnls and MINIDV

Hi all!
Is there a "workaround" to edit to tape a direct out 4 channels timeline to minidv via firewire?
To digtz i need to do it in a two pass way, and to edit to tape (?) VA12 via assemble and A34 via insert (?) is that it?
Thank you!
HBars

As long as your deck supports 4 channels, you can output 4 channels. That option was added with QT 7.
You need to go into the Timeline Prefs (Apple-0) click on the AUDIO tab and set the number of channels there.
Then on the timeline you need to assign the audio tracks to the channel you wish to output. Right-click or Option-click on audio tab on the left of the timeline and choose AUDIO OUTPUTS and choose the channel you wish to assign it.
Shane

Similar Messages

  • Can not stripe T/C using Edit-to-tape balck and code function

    I am in Edit-to-tape mode, mastering, I have T/C enabled, I am attempting to stripe an NTSC Digibeta; I click black and code and choose the settings and then select starting T/C (00;56;00;02) and click Drop Frame, click OK when it says it will erase the tape, but when it actually starts striping the tape, it does not start at 00;56;00;02, it starts at random times that appear to be generated externally.
    How do I actually stripe a tape and re-write T/C?
    Sorry, this is my first time doing projects like this.

    Decide whether you want drop frame or Non Drop Frame and set the switch accordingly ( switch under the flip out control panel) also verify your in record run here
    Set the TC switch on the deck to "INT" and "Preset" then set the TC start time, by pressing the "hold" button. You can now set hours min sec frames by pressing the jog button and rotating the jog wheel. rotate the jog wheel without pressing the jog button to select the next pair of numbers. when you have the desired start TC press the set button. If the deck is connected to black burst and you have no SDI input feeding it, and SDI selected as the input, the deck will generate black when you press record on the deck thus beginning your stripe. Stripe past 1 hr, stop the deck and rewind a little so you're in active code, set the TC switch back to "regen" from "Preset", make your patches put the deck in remote and assemble edit your piece. If you want to do an insert, stripe the tape out about 30 seconds past your last frame.
    the dbeta deck will insert or assemble. Not all decks will, some won't even assemble, only hard record. consult the deck manual when in doubt

  • Edit to tape transfer and TV auto wide screen

    I have a 16:9 SONY TV set with auto wide screen functionality
    When I play my original master plan recorded in 16:9 anamorphe setting, I see all the pictures in wide screen.
    After the capture with anamorphe settings, all the clips are display in wide screen mode on my TV set.
    But, after edit on an anamorphe sequence setting, when I play a render area, my TV set select automaticaly the 4:3 display.
    I note the same phenomenon after an edit to tape transfer.
    How can I to have an auto 16:9 wide screen on all my sequence ?

    I have a 16:9 SONY TV set with auto wide screen functionality
    When I play my original master plan recorded in 16:9 anamorphe setting, I see all the pictures in wide screen.
    After the capture with anamorphe settings, all the clips are display in wide screen mode on my TV set.
    But, after edit on an anamorphe sequence setting, when I play a render area, my TV set select automaticaly the 4:3 display.
    I note the same phenomenon after an edit to tape transfer.
    How can I to have an auto 16:9 wide screen on all my sequence ?

  • Edit to tape audio promlem - sounds like "chorus" effect

    I have tried to Edit to Tape an HDV Sequence, down converted to SD, to a Digibeta deck.
    When I monitor (headphone out of digibeta deck) while recording it sounds normal. When I rewind and check tape it sounds like the audio is "doubled up", almost like a very short chorus effect is on the audio. as well as this I can hear what sounds like tape crackle now and again.
    However - when I do a straight crash record from the timeline - the audio plays back fine, no crackle.
    So thinking it was an edit to tape settings problem i clicked on the audio button in the edit to tape window and notice audio was set to ALL ON. I changed this to A1 and A2 on, thinking that my extra audio tracks (which I had disabled, these where the original audio, not the OMF exported stereo mix) were somehow going down the SDI anyway...
    No luck - did the edit to tape again and still sounded the same.
    My heart rate has returned to normal now as the network kindly will accept the crash record with non standard timecode - but I of course still want to find out the problem so this doesn't happen again next week....
    The Sequence was HDV 1080i, via a Decklink HD Extreme Capture Card, set to down convert to anamorphic 16:9. Sony Digibeta DVW-A500P deck.
    Anyone know what the problem could be?
    thanks
    Hugh

    for the benefit of anyone who searches for forum for a similar problem - it appears to have been a sync issue. changing "out ref" to "input video" appears to have fixed it.

  • Editing to Tape problems

    Hi all,
    I am trying to edit to tape going form FCP 504 to a Sony DSR 45 DVCam deck. There seems to be no problems going to the SP Deck, however if I enter the in-point (as per manual) in the master mode edit to tape window, and then drag the sequence over, nothing seems to happen. I thought this may have somethign to do with the "insert timecode" button, which seems to remain yellow all the time... is this switched on or off? Either way I couldn't get it to change state.
    I have striped the tape at hour 10:00:00:00. The mastering window never seems to calculate the running time when hooked up to the Sony DSR deck, so I guess its just not seeing the sequence.
    For a while I did seem to progress but got a message to the effect that the deck was not in the right "mode" what ever that means. I have looked extensively in the settings for the deck but cannot see anything, I have also tried various different output settings and still no luck. The RS422 seems fine controlling the deck in non edit to tape mode, so I just cannot figure this out.
    Any feedback will be greatly appreciated.
    Nick
    G5 dual 2Gb   Mac OS X (10.4.6)   AJA card, 3GB RAM, DVCam & SP Decks

    Once again hmmmm.....
    I set all my setting for the DVCAM deck to use firewire and all the FCp settings for firewire. Even this ws not working! So I then repatched the video using the components in and hey presto its all works.
    It seems I am using the firewire to control the deck but the AJA Kona to output the actual video signal, eventhough no setting should be using the Kona - only direct firewire to firewire! Is this the opposite to what you said patrick? It all just seems so random really, but I guess it has something to do with the Kona and how thats controlling output... not sure.
    Just glad to be back up and running, although I have heard that the problem you suggest re frame accuracy may become an issue, but I read that it only usually has an effect on long programs.
    Thanks for your help, however please do suggest any reasons behind why only this set up works for me. I'd love to know whats going on for future problem solving.
    Regards, Nick
    G5 dual 2.7 Gb   Mac OS X (10.4.6)   AJA card, 3.5GB RAM, DVCam & SP Decks

  • Trying to "edit to tape"

    I am trying to use the edit to tape feature so that I can put a certain timecode on the tpe I'm printing out to. ... I am having issues with it ... I black the tape using the edit to tape feature and then try puting in the timecode that i want my video to start at and FCP will not let me drop in the sequence to the edit to tape window.
    I am using a panasonic DVCpro HD deck (my video is 1080i)
    nd I am trying to go through a blackmagic decklink
    please help! I need to be able to start picture at a certain TC on the tape
    Thanks!

    I ran into the same issue printing masters of our TV shows. The Outdoor Channel required the show to start at 01:00:00;00. We tried every way possible to get the TC through FireWire to the deck until I came across a blurb in the FCP user manual that says FireWire cannot output TC. You must have another type of deck control, like RS-422. We ended up using an old deck that was laying around to black 5 minutes of TC, then used edit to tape to do an assemble edit starting at the correct TC.
    If that's not an option for you, I did run across this thread while searching for an answer:
    http://forums.creativecow.net/thread/8/974059#974075
    I didn't try it, but its suppose to work!

  • Edit to Tape error

    I'm having an error of: "Unable to open the specified Video Output device" when trying to assemble to my DV camcorder. I have been able to use this feature before. I'm able to control my camcorder using the Edit to Tape window and set the in point. I know I can bypass this problem by Printing to Tape, but I want my sequence to start at a specific time, and I want to lay down black, bars and title beforehand.
    Any help is appreciated,
    reicko†

    Could be the tape... the error message is saying that it can't read the timecode in effect... tried another tape?
    If it fails again, could be the camera needs a cleaning or adjustment. If the recording isn't exactly right, you'll see TC errors then worse...
    If it were some sort of software bug, we'd all see the problem...
    Just for kicks you could try trashing prefs, but if all else seems to be OK, then it's more likely the tape or the camera. Cleaning cassette?
    Jerry

  • Edit to tape using Firewire

    Is it possible? I've just used a SONY M25 DVCAM deck and not been able to send timecode from FCP to the deck. It generates its own timecode and does not recognise timecode via firewire. The manual says it does take timecode via RS422 cable.
    Is this standard for all decks? Do any decks allow timecode in from FCP using firewire and therefore precise assemble edit control?
    Thanks for any help!

    Hi - I'm not sure if this info will be of any use to you, but -
    When using firewire to send video/control/edit to a DV deck your options are pretty limited.
    If your client wants the program to start at an even timecode number, you can do something like this:
    Put in a blank tape into the deck and rewind it to the head.
    Bring up the Edit to Tape window and press the "Black and Code" button
    !http://www.spotsbeforeyoureyes.com/BlackCodeButton.jpg!
    This will let you stripe the tape with black and code, unfortunately the code starts at 00:00:00:00.
    !http://www.spotsbeforeyoureyes.com/BlackCodeDialog.jpg!
    Once you have striped the tape with black and code, you can them make an edit in at specific timecode number - so if you have 1 minute of bars and tone, ten seconds of slate, 5 seconds of black and then your program starts - set your edit in point for 00:01:45:00 and your program will start at 00:03:00:00.
    Not as good as being able to start at 1:00:00:00 like the real world, but at least it is a precise start.
    Also - if your DV deck only allows for an assemble edit, and not an insert edit, make sure you add a minute or two of Slug to the end of your sequence so there won't be any tape break up close to the end of you program.
    Hope this helps.

  • Incompatible Compression Settings / Edit to Tape

    I'm working in Final Cut Pro 6.0.1 and trying to layback some video to Digi-Beta using a Kona3 video card. I'm new to this, so perhaps there are parts of this question I'm leaving out due to lack of knowledge.
    I'm getting this dialogue box when I attempt to "insert" in the Edit to Video box --
    Incompatible Compression Settings
    You may have attempted to output a clip with compression settings that do not match the current output settings, Try nesting the clip in a sequence with the correct settings.
    This is a clip captured in FCP and in it's a sequence with the same exact settings. I've gone through every window and made sure the settings are all AJA Kona3 525 29.97 10 bit. Everything I can find is consistent, and "should" work I think, but doesn't. What are the "correct settings?"
    If anyone can offer any help that would awesome. Again, I'm a bit of newbie at this so there is most likely information I forgot to mention or something I overlooked.

    #18 Edit to Tape "Incompatible Compression Settings"
    Shane's Stock Answer #18
    To Edit to Tape you either need to have your sequence loaded in the VIEWER, or simply drag it from the BROWSER onto the Edit to Tape window and choose Assemble Edit or Insert Edit.
    For both methods, the tape needs to be black and coded and have TC already on it. And you need to mark and IN point in the ETT window.
    Shane

  • Edit to tape confusing drop frame and non drop frame

    This is a re-creation of a dead thread I found from June 6, 2006. This is the exact problem this other user was having.
    OS 10.4.7
    FCP 5.0.4
    Dual G5 2.5
    4.5 GB RAM
    KONALH
    Trying to edit to a Sony DVW-A500 (Digibeta) in Drop Frame mode.
    Read Below for deets.
    Problem: When working with a drop-frame sequence, and editing to tape, the program is edited to the tape with an offset of 3 seconds and 18 frames at the end of one hour.
    Reproducible: Yes.
    Steps to Reproduce:
    1. Create a drop-frame sequence.
    2. Edit the sequence in step 1.
    3. Perform an edit to tape with the sequence edited in step 2.
    What should happen: The sequence should be edited to tape at the time it occurs in the timeline.
    What does happen: The sequence is edited to the tape 3 seconds and 18 frames after it should be!
    Other observations: 3 seconds and 18 frames is exactly how much time is not in an hour of drop-frame time when compared to non-drop frame time. If you drop two (2) frames in every minute that does not end in zero, the math works out to 2*54=108 dropped frames in an hour. For the sake of simple mathematics, lets say there are 30 frames in a second. So 108/30= 3 with a remainder of 18, or 3 seconds and 18 frames.
    It's as if FCP is getting confused about drop and non-drop timecode when the sequence is drop-frame. If anyone can offer any insights, confirmation, or resolutions for what I am seeing, it would be appreciated.
    Thanks for reading!

    So is the timeline a drop frame timeline, starting at 1:00:00:00?
    And then is the DBeta tape prestriped (at least enough to do an assemble edit) to start the program at 01:00:00:00?
    In other words, is the FCP timeline timecode matching the Dbeta tape timecode in a 1:1 relationship before you attempt to Edit to Tape?
    Thinking further: FCP can't really confuse the two timecodes, it's dependent on the operator to tell it what to do. When it outputs it's not outputing timecode or looking even really looking for timecode. It's looking for your IN point in the Edit to Tape tool.
    Message was edited by: loyed256

  • Drop-Frame v. Non-Drop Frame and Edit to Tape

    System Configuration: G5 Dual 2.0, QT v7.0.4, FCP v5.0.4, OS X v10.4.6, KonaLH, Keyspan USA-28x USB-->Serial Adapter
    Problem: When working with a drop-frame sequence, and editing to tape, the program is edited to the tape with an offset of 3 seconds and 18 frames.
    Reproducible: Yes.
    Steps to Reproduce:
    1. Create a drop-frame sequence.
    2. Edit the sequence in step 1.
    3. Perform an edit to tape with the sequence edited in step 2.
    What should happen: The sequence should be edited to tape at the time it occurs in the timeline.
    What does happen: The sequence is edited to the tape 3 seconds and 18 frames after it should be!
    Other observations: 3 seconds and 18 frames is exactly how much time is not in an hour of drop-frame time when compared to non-drop frame time. If you drop two (2) frames in every minute that does not end in zero, the math works out to 2*54=108 dropped frames in an hour. For the sake of simple mathematics, lets say there are 30 frames in a second. So 108/30= 3 with a remainder of 18, or 3 seconds and 18 frames.
    It's as if FCP is getting confused about drop and non-drop timecode when the sequence is drop-frame. If anyone can offer any insights, confirmation, or resolutions for what I am seeing, it would be appreciated.
    Thanks for reading!

    This may be related to a "bug" or issue that has been around since FCP1. When FCP is using deck control over firewire, The timecode display will default to DF, even if the tape is NDF. Look closely at the timecode dispays in the edit to tape window. If you see a semicolon before the frames place, FCP is seeing the tape TC as DF. Play the tape until you see the TC display change to NDF, then re-set your in point. This has worked for me in the past.
    Hope this helps.

  • HV20 and Print to Video or Edit to Tape?

    Has anyone figured out the workflow for final cut pro and getting video back out to tape using
    "print to video"
    or
    "edit to tape"
    with "edit to tape" I get an "unable to initialize" error where it tells me to check the audio/video settings.
    with "print to video"
    I'm using the record/pause function from page 71 of the manual, but the hv20 doesn't see to see a signal. Also the playback on the mac is interesting. it's in the middle of the screen, and not showing the full resolution..
    basically I'm just trying to dub an hdv tape.
    thanks!
    -Josh

    ok, the only things listed in the audio/video settings are the ntsc and pal firewire devices.
    when I try to set it to hdv 1080i60 firewire basic, I get the error:
    unable to locate the following external devices:
    HDV (1440 x 1080) 60i
    but the camera is both connected... and on. Is there a reason it would see the camera as an SD device instead of a HD device?

  • Assamble , insert , and edit to tape whith blackmagic.

    Hello , I have a macpro 5.1 with mavericks , 20 gb of ram and premier 2014 .
    When I do an insert or assamble ,  always gets 2 black frames. Change the offset in device options but still the same
    When edit to tape, the premier after 10 minutes or so , closes or freezes the video.
    I have all applications closed and disconnected from the network.

    check on your audio / video settings that there isn't a tick beside 'different output for print to video' on the AV devices tab

  • FCP5 and Send back to Tape (Edit to Tape)

    Help, I can't seem to figure this out.
    Sony FX1, FCP 5, Firewire.
    I am just brain dead, I have tried and failed.

    Hi FCP Folks,
    It just doesn't seem like FCP 5.0.3 and the Sony HDR-FX1 have been friends long enough to communicate well together. Capturing is no problem. But, 'Edit-To-Tape' is a no-go. Does anyone have a list of known-correct settings or any other app/camera configuration details that would let me 'Edit to tape' with my HDR-FX1?
    After trying MANY different combinations of settings I can report that the error is consistently, "Not returning timecode" FCP does not complain it can't communicate with the device - but it never seeks to a place on the tape or goes into the record mode.
    Should I write this up a bug?
    Thanks!
    Lance Drake
    NOTE: The link referring to: "Michael Mackay, "FCP5 & Sony HDR-HC1 HDV Cam - Print to Video?", 02:36am Sep 16, 2005 CDT" returns a 404 - Page Not found - error - so, no help from the existing info that might have been posted.
    G5 DP 2GHz   Mac OS X (10.4.3)   3.5 GB, HollywoodX Dazzle, FW card - neither in play

  • Sequence Back to Tape (Edit to Tape)

    Following along with the Apple Training FCP book, I tried Edit to Tape. I'm recording back to MiniDV on a little Canon ZR60. The footage that came with the training is some HD Seaworld stuff. Edit to tape seemed to work, and FCP started the camera recording, but all I got on the camera's LCD (both during recording and when attempting playback) was a blank screen. Is it because that footage was HD, and if I was backing up a sequence of SD footage it would have worked?

    Edit to Tape requires certain things. It requires deck control to a deck that can handle assemble and/or insert editing. It also requires that the format on the deck match the sequence being output.
    It sounds as if you were trying to send HD material through DV. Try dropping your HD sequence into a DV sequence, rendering and go again.
    If it still doesn't work, then it's possible your deck doesn't support Edit to Tape. However, Print to Video should still work.
    Andy

Maybe you are looking for