Editing a pre recorded .key
ALot has changed since I was in Keynote last, I have a keynote done by someone else and I need to do the following/
make the audio.mov file louder ( I have an audio editing tool was able to do but I cannot get the audio to playback the same way.
I see no audio settings like in older Keynotes nor do I see anything else as the original keynote plays back as a timed file with slides changing different times for each slide. I do not see where this is in each slide nor do I see anywhere to adjust the audio.
Any help?
I'm in 10.9.5 Keynote 6.2.2
make the audio.mov file louder
As there is no function in Keynote to increase sound levels you should use a sound editing application that has the ability to increase gain, then save as an mp3 or AIF file. Audacity, Compressor, Final Cut, Sound Recorder are examples.
Sound levels can be reduced using the volume slider in the Audio Inspector
I see no audio settings like in older Keynotes
Select the sound file on the slide, and make changes in: Inspector > Format > Audio
the same audio functions available in Keynote 5 are available in Keynote 6:
reduce sound volume
change the in point or outpoint
set to loop
as a timed file with slides changing different times for each slide
select the slide in the navigator panel and change settings in: Inspector > Animate > Start Transition
then change the option in the drop down menu to: Automatically then set a delay time
Similar Messages
-
I have been trying to work out how to edit pre-recorded vocals using the Voicelive 2 and Logic Pro. I have managed to figure out the settings on the voice live 2 but I cannot work out what to do on the logic side of things. This is what I have been told (see below), but I dont understand what this means.
In LOGIC you have to set up a SEND (to VoiceLive 2 via MAUDIO SPDIF out LEFT!!! CHANNEL ONLY) for sending the dry Vocal track and RETURN the processed signal on a new stereo track (from VoiceLive Rack / input source = MAUDIO SPDIF input L & R channels). Don't forget to record enable the track. To control harmony / detecting automatically the key, you may SEND any audio signal (i.e. your instrumental, piano/ rhodes chord track etc.) via MAUDIO SPDIF RIGHT!!! CHANNEL to VL 2.
Would anyone be kind enough to explain what this means and what I need to do? ( i am trying to post edit pre-recorded vocals using voice live 2, logic 9 and m-audio fast track ultra).
Thank youOpen GB, drag the AIFF file from the Finder onto the GB window
Hey presto!
Vince -
I am currently using an ASA 5550 version 8.2 anwith ASDM version 6.2.
I have a ASA 5505 in remote area and cannot connect via VPN.
My logs say maybe mismatched pre-shared key.
On my 5550, via the ASDM I used the command more system:running-config and it will not show my pre shared key in plain text, only shows a *.
Any help would be appreciated.Remote asa:
interface Vlan1
nameif inside
security-level 100
ip address 10.200.1.209 255.255.255.240
interface Vlan2
nameif outside
security-level 0
ip address 172.25.62.226 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
access-list nonat extended permit ip 10.200.1.208 255.255.255.240 10.199.1.0 255 .255.255.0
access-list nonat extended permit ip 10.200.1.208 255.255.255.240 10.10.144.0 25 5.255.252.0
access-list VPNL2L extended permit ip 10.200.1.208 255.255.255.240 10.199.1.0 25 5.255.255.0
access-list VPNL2L extended permit ip 10.200.1.208 255.255.255.240 10.10.144.0 2 55.255.252.0
access-list 100 extended permit tcp host 89.254.12.35 host 10.200.1.213 eq www
pager lines 24
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list nonat
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 172.25.62.225 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set mytrans esp-des esp-md5-hmac
crypto map mymap 10 match address VPNL2L
crypto map mymap 10 set peer 65.181.59.210
crypto map mymap 10 set transform-set mytrans
crypto map mymap 10 set security-association lifetime seconds 3600
crypto map mymap interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption des
hash md5
group 2
lifetime 86400
crypto isakmp nat-traversal 21
telnet timeout 5
ssh 10.199.1.0 255.255.255.0 inside
ssh 10.10.144.0 255.255.252.0 inside
ssh timeout 5
console timeout 0
tunnel-group 65.181.59.210 type ipsec-l2l
tunnel-group 65.181.59.210 ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:65a0d93601b90ccc07830cddd673e13c
: end
Local ASA:
ASA Version 8.2(1)
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 65.181.59.210 255.255.255.240
interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 10.199.1.2 255.255.255.0
interface GigabitEthernet0/2
nameif insideNOV
security-level 100
ip address 10.10.144.47 255.255.252.0
interface GigabitEthernet0/3
shutdown
no nameif
security-level 100
no ip address
interface Management0/0
shutdown
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
interface GigabitEthernet1/0
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet1/1
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet1/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet1/3
shutdown
no nameif
no security-level
no ip address
ftp mode passive
clock timezone MST -7
clock summer-time MDT recurring
dns server-group DefaultDNS
domain-name Rignet
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group service WML tcp
description Remote wits data access
port-object range 1 65535
access-list aclin extended permit object-group DM_INLINE_PROTOCOL_9 any host 65.181.59.219
access-list aclin extended permit object-group DM_INLINE_SERVICE_3 any host 65.181.59.216
access-list aclin extended permit object-group DM_INLINE_PROTOCOL_6 any host 65.181.59.220
access-list aclin extended permit object-group DM_INLINE_PROTOCOL_5 host 10.199.1.2 host 65.181.59.210
access-list aclin extended permit object-group DM_INLINE_SERVICE_1 any host 65.181.59.222
access-list no-nat remark Local Rules
access-list no-nat extended permit ip Rignet 255.255.255.0 10.10.144.0 255.255.252.0
access-list no-nat remark Local Rules
access-list no-nat extended permit ip 10.10.144.0 255.255.252.0 10.200.1.80 255.255.255.240
access-list no-nat extended permit ip Rignet 255.255.255.0 ENI 255.255.255.240
access-list no-nat extended permit ip 10.10.144.0 255.255.252.0 ENI 255.255.255.240
access-list no-nat extended permit ip Rignet 255.255.255.0 Norway_Office 255.255.255.240
access-list no-nat extended permit ip 10.10.144.0 255.255.252.0 Norway_Office 255.255.255.240
access-list no-nat extended permit ip Rignet 255.255.255.0 BobbyVPN 255.255.255.0
access-list no-nat extended permit ip 10.10.144.0 255.255.252.0 BobbyVPN 255.255.255.0
access-list inside_access_in extended permit ip any any
access-list inside_access_in extended permit tcp any any
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended permit tcp interface inside any
access-list inside_access_in remark Block port 135 for port scanning
access-list inside_access_in extended deny 135 any any
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_4 10.10.144.0 255.255.252.0 Rignet 255.255.255.0
access-list test extended permit icmp any any echo
access-list test extended permit icmp any any echo-reply
access-list InsideNOV_access_in extended permit ip 10.200.0.0 255.255.0.0 10.10.144.0 255.255.252.0
access-list InsideNOV_access_in extended permit object-group DM_INLINE_SERVICE_7 any any
access-list InsideNOV_access_in extended permit object-group DM_INLINE_SERVICE_4 Rignet 255.255.255.0 10.10.144.0 255.255.252.0
access-list InsideNOV_access_in extended permit object-group DM_INLINE_PROTOCOL_12 Norway_Office 255.255.255.240 10.10.144.0 255.255.252.0
access-list InsideNOV_access_in extended permit object-group DM_INLINE_PROTOCOL_8 BobbyVPN 255.255.255.0 10.10.144.0 255.255.252.0
access-list inside_acl extended permit object-group DM_INLINE_SERVICE_8 any any
access-list inside_acl extended permit object-group DM_INLINE_SERVICE_5 10.10.144.0 255.255.252.0 Rignet 255.255.255.0
access-list inside_acl extended permit object-group DM_INLINE_SERVICE_6 Rignet 255.255.255.0 10.10.144.0 255.255.252.0
access-list inside_acl extended permit object-group DM_INLINE_PROTOCOL_10 10.200.0.0 255.255.0.0 Rignet 255.255.255.0
access-list inside_acl extended deny object-group DM_INLINE_PROTOCOL_11 host 192.168.56.1 any
access-list inside_access_in_1 extended permit object-group DM_INLINE_PROTOCOL_1 any any
access-list inside_access_in_1 extended permit object-group DM_INLINE_PROTOCOL_2 10.10.144.0 255.255.252.0 Rignet 255.255.255.0
access-list inside_access_in_1 extended permit ip Rignet 255.255.255.0 Rignet 255.255.255.0
access-list inside_access_in_1 extended permit object-group DM_INLINE_PROTOCOL_7 BobbyVPN 255.255.255.0 Rignet 255.255.255.0
access-list inside_access_in_2 extended permit object-group DM_INLINE_SERVICE_11 Rignet 255.255.255.0 Rignet 255.255.255.0
pager lines 24
logging enable
logging asdm informational
no logging message 106015
no logging message 313001
no logging message 313008
no logging message 106023
no logging message 710003
no logging message 106100
no logging message 302015
no logging message 302014
no logging message 302013
no logging message 302018
no logging message 302017
no logging message 302016
no logging message 302021
no logging message 302020
mtu outside 1500
mtu inside 1500
mtu insideNOV 1500
mtu management 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any insideNOV
icmp permit any echo-reply insideNOV
icmp permit any echo insideNOV
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
global (inside) 2 65.181.57.51 netmask 255.255.255.255
nat (outside) 1 0.0.0.0 0.0.0.0
nat (inside) 0 access-list no-nat
nat (inside) 1 Rignet 255.255.255.0
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) 65.181.59.222 10.199.1.23 netmask 255.255.255.255
static (inside,outside) 65.181.59.219 10.199.1.27 netmask 255.255.255.255
static (inside,outside) 65.181.59.216 10.199.1.54 netmask 255.255.255.255
static (inside,outside) 65.181.59.220 10.199.1.26 netmask 255.255.255.255
access-group aclin in interface outside
access-group inside_access_in_1 in interface inside
access-group InsideNOV_access_in in interface insideNOV
route outside 0.0.0.0 0.0.0.0 65.181.59.209 1
route inside 153.15.156.217 255.255.255.255 65.181.57.51 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication http console LOCAL
aaa authentication ssh console LOCAL
aaa authorization command LOCAL
snmp-server enable traps snmp authentication linkup linkdown coldstart
snmp-server enable traps syslog
snmp-server enable traps ipsec stop
snmp-server enable traps entity config-change
sysopt connection tcpmss 1100
sysopt noproxyarp inside
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set mySET esp-des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map myDYN-MAP 5 set transform-set mySET
crypto dynamic-map myDYN-MAP 5 set security-association lifetime seconds 28800
crypto dynamic-map myDYN-MAP 5 set security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map myMAP 65000 ipsec-isakmp dynamic myDYN-MAP
crypto map myMAP interface outside
crypto ca trustpoint Intelliserv.rignet.local
enrollment terminal
subject-name CN=Rignet5550
keypair IntelliServ.rignet.local
crl configure
crypto ca trustpoint ASDM_TrustPoint3
crl configure
crypto ca trustpoint ASDM_TrustPoint0
enrollment terminal
subject-name CN=Rignet5550
password *
crl configure
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption des
hash md5
group 2
lifetime 86400
crypto isakmp nat-traversal 21
telnet timeout 5
console timeout 0
management-access inside
no threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
group-policy myGROUP internal
group-policy myGROUP attributes
split-tunnel-policy tunnelspecified
nem enable
username GaileyB password 0oaTL6AGb4l6JKde encrypted privilege 15
username rignetadmin password 3R8hQCl0jw5iU/r3 encrypted privilege 15
tunnel-group DefaultL2LGroup ipsec-attributes
pre-shared-key *
tunnel-group mytunnel type remote-access
tunnel-group mytunnel general-attributes
default-group-policy myGROUP
tunnel-group mytunnel ipsec-attributes
pre-shared-key *
tunnel-group 164.85.0.18 type ipsec-l2l
tunnel-group 164.85.0.18 ipsec-attributes
peer-id-validate cert
chain
tunnel-group-map default-group DefaultL2LGroup
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
class class-default
service-policy global_policy global
prompt hostname context
Cryptochecksum:a84cff45794fa5021237d51d5f87461e
: end -
Need help recording Video over pre-recorded Audio
I'm making a music video, the audio has already been recorded, but I am having such a hard time trying to figure out how to record the video over it. I need to be able to hear the audio track while recording so I can sync it properly, but whenever I click on the 'Open Camera Import Window' button, it doesn't allow you to playback the audio. What is the easiest way I can go about this?
PS. If my question is vague or unclear, I'm sorry. Every person I have asked said they had no clue what I was asking.Hi Rick,
Thank you for your response.....I have always done this process using other software for the videos....so the process here is different for me.
I pre record the audio first, then edit to remove all of the terrible sounds...breathing, mispoken words, etc...clean up the audio, then add a background music track all in Audacity. Then, I add that track in and record my video over it. I am creating a tutorial for a software company on how to use their software.
This may seem backward. My question now, I am in Captivate 7, I press video demo and it goes straight to recording the video before I have a chance to import the audio track. I need the audio track so I can get the video to follow the audio...if that makes sense.
Cheers...Robert -
Hi! It would be great if someone could tell me how to pre-record timings in a keynote presentation, so that when presented, it plays by itself, based on the pre-set recordings. I know there is a way to do it by going to Inspector>Document> Audio> Record However when you do this, your computer also records the sounds it picks up with the microphone, which can greatly affect the sound. I have Keynote '09. Thanks in advance!
-AppleMe123Open the Settings app > Notifications > Messages. Scroll down adn turn OFF "View In Lock Screen". You may want to consider setting Alert style to none, but this will not impact what happens when the screen is locked.
-
How can I set up a default (pre-recorded) voicemail greeting on iphone 4s?
How can I set up a default (pre-recorded) voicemail greeting on iphone 4s?i dont want a custom one with my voice i want the pre-recorded where a lady says my number . how do i get that?
Voicemail is a cell phone carrier function. Contact your carrier to see if they have this option. If not, i'm sure you can download a sound file from the internet with a greeting and add your name. Then play it back on you PC while holding your iPhone near the speaker when recording the greeting to voicemail.
-
MDM API to read the Record Key Mapping table
Hi,
Does anybody know what class/method I can use to read the Record Key Mapping table?
For the Business Partner table the Key Mapping table has this columns:
<u>Default / MDM Partner ID / Remote System / Key</u>
I have everything but the Key. How can I read it?
Thanks in advance,
Diego.GetKey Mapping is one of the available Web Services as of SP4.
Else you could use the Java API to get the Key Mapping.
<b>CatalogData class</b> has the following method
<b>GetKeyMapping</b>
public java.lang.String[][] GetKeyMapping(java.lang.String agency,
java.lang.String table,
int[] recordIDs,
boolean isDefaultKeyOnly)
throws StringExceptionRetrieves the key mapping for each record.
Parameters:
agency - the agency name.
table - the table name.
recordIDs - the list of records.
isDefaultKeyOnly - True to retrieve only the default value, False to all key values.
Returns: the key values for each record. -
When I put a Pre Recorded CD into my computer it's not showing up on I-tunes file?
When I put a Pre Recorded CD into my computer it's not showing up on my i-tunes file, does anybody know why?
In iTunes, if the sidebar (along left side of window) is hidden, from the menu bar, under View, select Show SIdebar. After inserting the music CD, it should appear in the sidebar, under DEVICES.
-
I have my Windows Server 2008 standard installed with RRAS service and configure with L2TP VPN with pre-shared key. Services such as Active Directory, DHCP and DNS are not installed. The Internet connection doesn't pass through a router to my server machine.
I have the Verizon fios Internet cable plugged in to the server machine directly.
PCs running Windows and Mac OS X can connect to the server without problem. When I tried to connect by using android or iOS mobiles and tablets, they cannot connect to the server. If I change the VPN type to PPTP, the mobile devices can connect successfully
but I would like to use IPSec/L2TP since it's more secure.
I tried so hard to look for the solution for this issue on Internet but I had no luck on that. Can anyone please provide me some help, please ?
Thanks,
CKHi CK,
I think we may need to create a policy in Network Policies. Please follow the steps below,
Right click Network Policies, Click New.
Enter the policy name, click Next.
Click Add, select the Day and Time Restrictions, click
Add.
In the Day and Time Restrictions, choose Permited for
all, click OK.
Click Next five times(leave everything default), click
Finish.
Move the policy to top and try to connect with your device.
If issue persists, please make sure that the Connection Requet Policies have been configured properly.
For detailed information about how to create a network policy, please refer to the link below,
Configuring NPS network policies
http://technet.microsoft.com/en-us/library/dd441006.aspx
Best Regards.
Steven Lee
TechNet Community Support -
Options for pre-recorded voice paging
What options are there for pre-recorded voice paging on Cisco Phone Systems.
We are running Cisco Unity Express 3.1 on a Cisco 2851 and I have a ATA186 that connects to a PA System that has an extension assigned to it.
So what I would like to do is select between 2 or three pre-recorded messages and play it over that extension.
I know Informacast will do it but that is a little expensive in my opinion for what I want to do.Take a look at SynApps SA-Announce and Broadcast Manager: http://syn-apps.com
Both are great products, compatible with CME, and are typically cheaper than other options. -
HT1567 My lap top is not recognising my pre recorded cd and will not burn a cd. Help
Help! My lap top is not recognising a pre recorded cd in itunes and it wont burn a cd. Anyone know why?
Try (copy & paste):
drutil eject -drive internal
then insert a disc.
If that doesn't do the trick, Zap the PRAM and Reset the SMC, and try again. -
Duh.. cannot open calendar page to edit it. What key option works??
First time in 20 years with Mac I am asking this kind of question.
ThanksFound it>>> return and both mouse keys !!!!????????
-
How to visually separate elements in a pre-recorded song?
I'm hoping to use Audition in a research project to study patterns in music. I just downloaded it last night and I'm using the trial period to evaluate if it will meet my needs. I am running the program on a Mac.
As stated above, I'm hoping to use Audition in a research project. to study patterns in music. I need to be able to do this with pre-recorded songs (songs downloaded from iTunes). I do not need to actually separate vocals or other elements (i.e. only hear one or the other), but I am hoping to be able to visually see the vocals, melody, base, drums, other accompanying instruments separate from each others (see their separate frequency waves). So for example, I would like to visually see the main vocals increasing in volume, changing from low to high notes, seeing a note sustained for a period of time, and noting how these patterns coincide with other elements in the song.
I am very much a novice so I am not able to describe this in "music terminology". I have seen the "frequency displays" when playing a song that show the right and left channels - but all the elements are merged together making it impossible to really visually see any patterns. I've tried to play around with some of the options in the effects menu (Amplitude and Compression; Filter and EQ), but I have not found an option that provides what I'm looking for.
Does Audition provide the feature I'm hoping for? Can someone help point me in the right direction for achieving this?
Thanks!!!!!Not really.
The only way to have visually separate elements is to have each element separate. They'd exist this way in the original recordings prior to the mix but, as soon as they're mixed trying to split them out is like "trying to unbake a cake" (to use a common forum cliche). If you think about it, this makes sense--440Hz from a human voice is the same as 440Hz from a piano--so in the display (which is a mix of amplitude and frequency) they show up as the same.
It MIGHT be worth you having a look at things in Spectral View. This is a useful analytical tool for a lot of things and may show up some interesting stuff--but, even there, I doubt it would give all the info you want.
This isn't an Audition limitation by the way...I don't know of any audio software that can "unbake the cake" as you need to.
If it was me, instead of downloading finished songs from iTunes, I'd be approaching hobby musicians and asking/begging for copies of their original, pre-mixed tracks. There are various home recording forums (indeed, one called "Home Recording") and some there might be able to help. However, even with the original tracks, be aware that they don't necessarily show the levels graphically--typically there would be a display of the original track plus some sort of automation system (which may show you a line going up and down) indicating what is happening to the levels. -
- What are the uses of 'record key' and 'line number' in the DTW template?
So It is like indexing the records? okie..
Let me tell you a scenario. Please tell me what would be the result.
scenario 1:
Items to be uploaded: 200
number of templates: 2 ( 100 items per template)
I define the record key 1- 100 for the 100 items in the first template
I also define the record key 1-100 (not 101 -200) in the second template
In this attempt, what will be the result? will the second template items update the first template items? -
WLC: Need to change pre-shared key with a script
Hello,
I need to change pre-shared key on a Guest Wi-Fi with a script.
Does anybody has an idea how to find the right entry in the WLC 2125 MIB to change it through SNMP?
GorazdHi,
That is a textFramePreferences property
mySelection.textFramePreferences.verticalThreshold = Number (range 0- 8640)
ID Object Reference says:
"...The maximum amount of vertical space between two paragraphs. Note: Valid only when vertical justification is justified; the specified amount is applied in addition to the space before or space after values defined for the paragraph..."
Maybe you are looking for
-
How to restrict the data with Filter in Query - Updated the description
Hi all, Free Characteristics: u2018Service Orderu2019 & u2018Statusu2019. Key Figures: u2018Response Timeu2019 & u2018Data Record Counteru2019. Calculated Key Figure: u2018Resp Time > 1 hru2019. Only u2018Plantu2019 is in ROWS and u2018Resp Time > 1
-
Https access to Sap Content Server 620 with R/3 46C
We are trying to access the Sap Content Server 620 via Https. We do not want to administer it via HTTPS, (as we know CSADMIN doesn't support Https in rel. 46C as for note 712332). We want to do in way that the users when do check-in/out of originals
-
Is it possible to create a domain with 2 Foundation 2012 servers ?
Hello, I need to install Windows 2012 servers, acting as DHCP servers, each one managing half of the IP range. There will be less than 5 users registered in this domain. My question is : can I use 2 Foundation versions (each one being a DC) ? Thanks
-
Hoping someone can help please. Can't open itunes.
Hoping someone can help please. Whenever I try to start itunes it asks me to accept terms and conditions and then when i click "agree" to continue nothing else happens and it won't open. I recently had to re-install itunes as it wouldn't work when i
-
Oracle Learning Management - tracking
Good Morning All, I have content, I have an LMS (Oracle Learning Management), I've published with the SCORM options in Cap 3. I have changed the .xsd files to the Oracle specific files. I can launch the course through OLM. I can see data in the Suspe