EEE 701 - Help getting eGalax touchscreen to work?
I just installed a touchscreen from dealextreme on my wife's old eee 701 and I'm hoping someone else around here has done so and has some insight as to drivers for this thing?
the device shows up with lsusb but I'm kinda lost where to go from here.
Last edited by ctarwater (2009-12-22 06:28:36)
ok gborzi, thanks for all your help earlier...I got it!
for anyone else interested, here's how I did it.
1) install xf86-input-evtouch from AUR
2) install ttf-freefont and xdialog
3) blacklist the usbtouchscreen module
4) run the touchscreen calibration script
5) open the /etc/evtouch/config file and delete everything after the 4th line (MAXY="xxxx")
6) open /usr/share/hal/fdi/policy/20thirdparty/50-eGalax.fdi and add the following 2 lines to the end:
<merge key="input.x11_options.swapy" type="string">true</merge>
<merge key="input.x11_options.rotate" type="string">CCW</merge>
I hope this helps anyone else trying to install a eGalax touchscreen.
here is my full eGalax.fdi file if anyone is interested: http://pastebin.com/f591374d8
here is my full evtouch config: http://pastebin.com/f17b8136e
These should work on all eGalax touchscreens installed on an eee701 since the hardware is the same.
here is a screenshot of my daughter's new computer. Thanks!
Last edited by ctarwater (2009-12-24 03:07:09)
Similar Messages
-
I have been able to trick my ipod into letting me in but I still can't get the touchscreen to work this is extremely annoying and I was wondering if i should just get a new ipod or what?
You need a computer with iTunes and an internet connection
Try:
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
[SOLVED] Samsung q1 ( egalax ) touchscreen not working with Xorg 1.6
I was using egalax touchscreen driver 2.06.2410 in my samsung Q1 :
http://home.eeti.com.tw/web20/eGalaxTou … Driver.htm
With the Xorg update to 1.6 version touchscreen stop working. If you want it back you can use this egalax_drv.so i got from eeti:
http://rapidshare.com/files/228797256/e … rv.so.html
Liquibyte and Kriblom kindly provided alternative (and probably better ) hosting:
http://www.liquibyte.com/driver/egalax_drv.so
http://dont-looze-touch.ovh.org/egalax_drv.so
It do worked for me using the 2.06.2410 driver and overwriting the old egalax_drv.so in /usr/lib/xorg/modules/input. I'm on 32 bit and i don't know if this do work in 64 bit too.
Last edited by ernia (2009-05-04 06:09:27)Actually I've just gotten it. I'll just post mine in case it's useful to someone else.
Section "ServerLayout"
InputDevice "EETI" "SendCoreEvents"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
EndSection
Section "ServerFlags"
Option "AutoAddDevices" "False"
Option "DontZap" "false"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
Identifier "Card0"
Driver "intel"
VendorName "Intel Corporation"
BoardName "Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller"
BusID "PCI:0:2:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
Modes "1024x600"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
Modes "1024x600"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1024x600"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
Modes "1024x600"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1024x600"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1024x600"
EndSubSection
EndSection
### Touch Configuration Beginning ###
Section "InputDevice"
Identifier "EETI"
Driver "egalax"
Option "Device" "usbauto"
Option "Parameters" "/var/lib/eeti.param"
Option "ScreenNo" "0"
EndSection
### Touch Configuration End ###
Editing for brevity.
Last edited by liquibyte (2009-05-03 19:54:42) -
I need help getting Mini Bridge to work in PS CS6
I have already tried deleting the folder and rebooting the computer, I have tried creating a new user account, I have tried uninstalling and reinstalling the entire package and I cannot get Mini Bridge to work at all. It just keeps going to "Mini Bridge waiting for Bridge CS6..." and then never finds anything. I am having this issue on both my Macbook Pro Retina 15 and my MacBook Pro 13 (Early 2011 model). I cannot seem to find any other solutions to this problem online. I also made sure that both Macbooks are fully updated as well as all CS6 software titles. Please help me fix this!
I also made sure I added it to the exceptions list in the firewall too.Moving the discussion to PS forum
You can also follow the solution suggested in http://helpx.adobe.com/photoshop/kb/error-waiting-for-bridge-cs5.html
they may help -
I need help getting this program to work.
K. I don't pay much attention in my AP Comp Science Class.. but my teacher said if i can get this program to work i get an a for the semester... The program is Metrowerks Codewarrior IDE.. we are running it on windows 98 i think. She said she can't get it to compile.. so i guess it just needs to be able to input simple java programs (i.e. loops, just the regular crap) and compile them and run them...i have no clue what is wrong with it.. it could just need a patch...or we may just be going about it the wrong way...any help would be SUPER appreciated...
K. I don't pay much attention in my AP Comp Science
Class.. but my teacher said if i can get this programYou better did.
to work i get an a for the semester... The program is
Metrowerks Codewarrior IDE.. we are running it on
windows 98 i think. She said she can't get it toAtleast be sure of the OS.
compile.. so i guess it just needs to be able to
input simple java programs (i.e. loops, just the
regular crap) and compile them and run them...i have
no clue what is wrong with it.. it could just need aEven we don't.
patch...or we may just be going about it the wrong
way...any help would be SUPER appreciated...Nothing in your thread really speaks of the problem. And since you mentioned homework, there's hardly anyone to be interested in that.
Regards
***Annie*** -
Need help getting guest access to work.
I have searched and Googled and found very little about enabling temporary guest access on an AEBS.
What I could find said just type in "the PIN number." OK, what PIN number? It appears that the device seeking access is supposed to supply it somehow and then I type it in while using the Airport Utility. I see no such number on the device. I also tried the "first one to try" method and got nowhere.
In both cases I was using an iPhone that wanted to use my network. Does this work with iPhones?
Many thanks,
-danThis thread http://discussions.apple.com/thread.jspa?messageID=4088108� looked helpful but I can't get guest access to work for my son's guest using a Dell XP laptop (using Dell wireless management) despite allowing timed access. Neither the PIN nor the first attempt option allowed him on the network without giving him our password.
It's still not clear if or when this will work. At the very least, the documentation is terrible. -
Need help getting this code to work
I am trying to get this code to work using "if else statment" but it will only do the first part and not do the second part in the else statement. Can anyone help me out? Here is the code:
var R1 = this.getField("Registration Fees1");
var R2 = this.getField("Registration Fees2");
var R3 = this.getField("Registration Fees3");
var R4 = this.getField("Registration Fees4");
var R0 = 0
if (R0 == 0)
event.value = Math.floor(R1.value);
else
event.value = Math.floor(R2.value + R3.value + R4.value);
I did notice that if I fiddled around this this part:
if (R0 == 0)
sometimes I can get the second part to work but not the first. I need it to do either or and this is getting frustrating.
I might also not even need "var R0 = 0". I put that there for the condition part. If that is what is causing the problem, I can take it out. But then what would the condition be? For this form, the default is 0 and then the calculation follows by user clicking on different prices. The first part is if they want to pay for the full conference and the second part is if they want to pay for either Monday, Tuesday or Wednesday or 2 of the 3 days. Is it possible to get this to work with both parts together? I am still stuck on getting just one or the other working. Any help would be greatly appreciated. Thanks in advance.I have posted this on another message board and a user by the name of gkaiseril offered this solution but it hasn't worked either.
// all four days
var R1 = this.getField("Registration Fees1").value;
// Monday
var R2 = this.getField("Registration Fees2").value;
// Tuesday
var R3 = this.getField("Registration Fees3").value;
// Wednesday
var R4 = this.getField("Registration Fees4").value;
var Fee = 0
event.value = ''; // default value
if (R1 != 'Off') {
Fee = Number(R1) + Fee;
} else {
if(R2 != 'Off') {
Fee = Number(Fee) + R2;
if(R3 != 'Off') {
Fee += Number(R3);
if(R4 != 'Off') {
Fee = Number(R4) + Fee;
event.value = Fee; -
Help getting SQL Developer to work
I'm just trying to get SQL Developer to work so I can use student databases. I have no intent of being a networker, and I definetly have no intent of failing this class because I can't do my homework.
Update.
Someone from my Java Class told me to restart the services related to Oracle. I attempted to do so, but got the following errors:
http://img220.imageshack.us/img220/5087/clipboard01hq.jpg
http://img27.imageshack.us/img27/32/clipboard02ro.jpg
I believe the TNSListener service is the main problem (seeing as when I try to open the database I get an error saying "TNSListener service is not running.") So I looked that up, and it said to check sqlnet.log:
Sat Jan 29 18:11:16 2011
Create Relation ADR_CONTROL
Create Relation INC_METER_IMPT_DEF
Create Relation INC_METER_PK_IMPTS
Directory does not exist for read/write [C:\app\Davidi\product\11.1.0\db_1\log] [C:\app\Davidi\product\11.1.0\db_1\log\diag\clients]
Fatal NI connect error 12541, connecting to:
(DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=127.0.0.1)(PORT=1521))(CONNECT_DATA=(SID=orcl)(CID=(PROGRAM=C:\Install\sqldeveloper-2.1.1.64.45\sqldeveloper\sqldeveloper.exe)(HOST=THE-FALCON)(USER=Davidi))))
VERSION INFORMATION:
TNS for 32-bit Windows: Version 11.1.0.6.0 - Production
Windows NT TCP/IP NT Protocol Adapter for 32-bit Windows: Version 11.1.0.6.0 - Production
Time: 29-JAN-2011 18:11:18
Tracing not turned on.
Tns error struct:
ns main err code: 12541
TNS-12541: TNS:no listener
ns secondary err code: 12560
nt main err code: 511
TNS-00511: No listener
nt secondary err code: 61
nt OS err code: 0
Thu Feb 03 23:04:39 2011
Directory does not exist for read/write [C:\app\Davidi\product\11.1.0\db_3\log] [C:\app\Davidi\product\11.1.0\db_3\log\diag]
Fatal NI connect error 12541, connecting to:
(DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=The-Falcon)(PORT=1521))(CONNECT_DATA=(SERVICE_NAME=orcl)(CID=(PROGRAM=C:\Install\sqldeveloper-2.1.1.64.45\sqldeveloper\sqldeveloper.exe)(HOST=THE-FALCON)(USER=Davidi))))
VERSION INFORMATION:
TNS for 32-bit Windows: Version 11.1.0.6.0 - Production
Windows NT TCP/IP NT Protocol Adapter for 32-bit Windows: Version 11.1.0.6.0 - Production
Time: 03-FEB-2011 23:04:41
Tracing not turned on.
Tns error struct:
ns main err code: 12541
TNS-12541: TNS:no listener
ns secondary err code: 12560
nt main err code: 511
TNS-00511: No listener
nt secondary err code: 61
nt OS err code: 0
Thu Feb 03 23:08:05 2011
Directory does not exist for read/write [C:\app\Davidi\product\11.1.0\db_3\log] [C:\app\Davidi\product\11.1.0\db_3\log\diag]
Thu Feb 03 23:08:31 2011
Directory does not exist for read/write [C:\app\Davidi\product\11.1.0\db_3\log] [C:\app\Davidi\product\11.1.0\db_3\log\diag]
Thu Feb 03 23:09:36 2011
Directory does not exist for read/write [C:\app\Davidi\product\11.1.0\db_3\log] [C:\app\Davidi\product\11.1.0\db_3\log\diag]
And now I'm stuck again. Does anyone have any suggestions?Oh right. I did change the port in an attempt to get Scott to work.
Changed back to port 1521, but still no luck.
I think my problem has something to do with OracleDBConsoleorcl. I get Error Code 2 when I try to start that service up.
Although...my SERVERNAME_SID is 192.168.15.101_orcl (Directory: C:\app\Davidi\product\11.1.0\db_1\192.168.15.101_orcl)
Which was the IP Address ipconfig set up the day that SQL Developer was actually working. Of course, that IP Address changes every time you restart windows. My teacher suggested that I set up a static IP Address or try setting it to local host, but I really don't know how to do either of those.
Any help would be appreciated.
Thank you. -
Help getting streaming audio to work?
I am a new user to Mac OS as of a few weeks ago. I'm making the transition fairly well.
Using Safari, I can't get streaming audio to work on my hometown radio show.
Here's the link to the home page... http://www.kdkaradio.com/ Near the top right of the page is a button to listen live.
I read somewhere that you have to have Windows Media Player installed and I did that and it still doesn't work. I thought you might need a plugin with Firefox and I can't get it to work either.
Any help would be greatly appreciated,
Thank you,
Dan
MacPro Mac OS X (10.4.8)Welcome to Apple Discussions and Mac Computing.
Glad to hear the transition is easy. You might find
Scott Kelby's book
OS X Tiger: Killer
Tips helpful.
To your question:
Windows Media Player does not play natively on Intel
machines. You need to use the free
Flip4Mac plug-in as a
substitute for WMP. Microsoft has stated they do not
plan to create a Universal Binary app. for the
Windows Media Player.
On my machine:
No go on Safari. When I select "live" I get to the
page showing a template of a music player, but no
sound.
On Firefox, a separate sound panel opens, however,
the feed stops before sound occurs. Strange though,
the various highlight feeds do play with no problem.
I suggest you contact the web developer at the
station for clarification regarding the Mac
platform, and just what is compatible with their
content stream.
I'm using Flip4Mac in place of WMP.
Thank you very much for your help and support.
I uninstalled Windows Medial Player and installed Flip Mac.
I'll have to check out your book suggestion.
I am still getting the same error, page not found when trying to listen live. All the other feeds work fine. I emailed the radio station to see if they could resolve the problem.
Thanks again,
Dan -
[SOLVED] Need some help getting the sound to work again
Recently I changed the motherboard and CPU to an AM3 platform, everything works with my previous setup except sound.
Reinstalling alsa-utils and rebooting had absolutely no effect. Google didn't help either.
lspci -v
00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2)
Subsystem: ASUSTeK Computer Inc. Device 8415
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 11
Memory at dfff4000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel modules: snd-hda-intel
The motherboard documentation refers to it as "VIA VTI708S".
VLC complains about alsa-lib. Reinstalling it also didn't help.
aplay /usr/share/sounds/alsa/Front_Center.wav
ALSA lib confmisc.c:768:(parse_card) cannot find card '0'
ALSA lib conf.c:4154:(_snd_config_evaluate) function snd_func_card_driver returned error: No such file or directory
ALSA lib confmisc.c:392:(snd_func_concat) error evaluating strings
ALSA lib conf.c:4154:(_snd_config_evaluate) function snd_func_concat returned error: No such file or directory
ALSA lib confmisc.c:1251:(snd_func_refer) error evaluating name
ALSA lib conf.c:4154:(_snd_config_evaluate) function snd_func_refer returned error: No such file or directory
ALSA lib conf.c:4633:(snd_config_expand) Evaluate error: No such file or directory
ALSA lib pcm.c:2211:(snd_pcm_open_noupdate) Unknown PCM default
aplay: main:654: audio open error: No such file or directory
alsamixer
cannot open mixer: No such file or directory
Edit:
Damn ASUS font... It's "VIA VT1708S" (number one, not the letter "i") ! Duh. No wonder Google couldn't find any info.
Still, any ideas ? Or would you just rather let me squirm a little and diagnose the problem myself ?
Last edited by DSpider (2010-11-28 18:15:41)sudo modprobe snd-hda-intel
(I think it's what you tried to tell me, igndenok)
Great. It took the bulk of my day trying to figure out how to get this thing to work.
VolWheel is now set to adjust "Master Front" (it was previously set to "Master" with the old motherboard) and the Sonata volume bar apparently works too, just like I wanted (adjusting the PCM volume by default). Good. Great ! Now I just need to set the "snd-hda-intel" module to load at boot so I don't have to type "sudo modprobe snd-hda-intel" all the time and this thread can be considered SOLVED.
sudo nano /etc/rc.conf
...and add the following:
MODULES="... snd-hda-intel ..."
(also removed snd-ac97-codec from the list because that's what the old mobo used)
THANKS FOR ALL YOUR HELP !
PS: Just out of curiosity, why is it called "snd-hda-intel" ? Why intel ? The CPU is AMD, the chipset is Nvidia nForce, sound is VIA...
Anyone know ? I'll subscribe to this topic just in case anyone knows. Thanks again.
Last edited by DSpider (2010-11-28 18:16:36) -
Need help getting Apple Extreme to work with Be box
Anyone able to give an idiots guide to getting Apple Extreme to work with Be Box wireless modem?
Used to have Orange (Wanadoo) broadband with Livebox wireless router, which i had my AE wired up to and it worked fine. Signed up with Be* and managed to get their wireless router working and communicating with my Mac OK. When i hooked up AE the green light came on but i can't manage to get my Mac to find it.
Any help would be very appreciated.
Thanks.Hello Orang Hutan. Welcome to the Apple Discussions!
What is your connectivity goal for the 802.11n AirPort Extreme Base Station (AEBSn)?
o Connect it directly to the Be Box wireless router via Ethernet, or
o Connect it wirelessly to the Be Box's wireless network?
If it is to go the wireless route, do you want the AEBSn to extend the wireless range of the Be Box? -
I need help getting my printer to work
I need help getting my printer to work
http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/Want-Good-Answers-Ask-Good-Questions/td...
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
Need help getting LCD monitor to work with G4 GeForce4 MX
I have a G4 that I haven't been using and want to get running again. It has a Nvidia GeForce4 MX video card. I had a huge CRT monitor and want to use a ViewSonic VX1935wm which I got a deal on. When I hook the monitor up it says that the resolution is out of range.
I can boot with my old monitor and change the connection and then get the LCD to work but only at certain resolutions.
Do I need to get a new video card, or can I get an adaptor? What kind of card should I get if it needs to be replaced? Or what other kind of monitor would be supported by this video card?
Here is the webpage for this monitor: http://www.viewsonic.com/products/lcddisplays/xseries/vx1935wm/thanks for the links.
switchResX does something, but it doesn't solve the problem. i can now switch to the "optimum" resolution of 1440x900, 60hz. but when i restart the computer, it still won't work! i continue to get the "out of range" message and have to boot with my crt and then switch cables to do anything. also, the fonts in the finder menus look terrible, you can see the jagged lines.
displayConfigX won't let me test that high of a resolution without registering the product.. needless to say, i don't want to pay money if the results are going to be the same as with SwitchResX.
I sent an e-mail to ViewSonic support. Is it typical to have these problems? I am getting more and more confused as I learn more about this. -
Can't get eGalax touchscreen Lilliput Eby701 working on linux 3.7x64
I recently purchased a 7" touchscreen for my carputer project which I am trying to use under arch. It is the Lilliput Eby701-np/c/t model.
DE: Ich kaufte vor kurzem ein 7 "Touchscreen für meine carputer Projekt, das ich versuche, unter Bogen verwenden werde. Es ist das Lilliput Eby701-np/c/t Modell.
I am running kernel 3.7.7-1 with nouveau loaded in kernel mode setting if it makes any difference. I cannot build xf86-input-evtouch from AUR and the eGalax driver doesn't function with my kernel (when I enable it, the touchscreen doesn't recognize input of any kind). The eGalax graphical driver utility runs and recognizes that the touchscreen is in fact connected via USB, but crashes every time I try to run the 4 point calibration.
DE: Ich bin mit Kernel 3.7.7-1 mit Jugendstil im Kernel-Modus-Einstellung geladen, wenn es einen Unterschied macht. Ich kann nicht bauen xf86-input-evtouch von AUR und eGalax Fahrer nicht mit meinem Kernel funktionieren (wenn ich sie zu aktivieren, der Touchscreen nicht erkennen Eingabe aller Art). Die eGalax grafische Treiberprogramm läuft und erkennt, dass der Touchscreen in der Tat über USB angeschlossen ist, sondern stürzt jedes Mal, wenn ich versuchen, die 4-Punkt-Kalibrierung laufen.
The only driver which "worked" was the one loaded by default (evdev) as soon as I plugged the touchscreen into my USB port. Unfortunately, the Y axis was inverted, the X and Y axes were swapped and the calibration wasn't even close to right. To "fix" the problem, I did the following:
DE: Der einzige Treiber, die "funzt" war das standardmäßiges evdev, sobald ich den Touchscreen steckt in meinem USB-Port. Leider wurde die Y-Achse invertiert, die X-und Y-Achsen wurden ausgetauscht und die Kalibrierung wurde nicht einmal nach rechts zu schließen. Um das Problem zu "melden", habe ich die folgenden gemacht:
Created a bash script:
sudo xinput set-prop 9 "Evdev Axes Swap" 1
sudo xinput set-prop 9 "Evdev Axis Inversion" 0, 1
sudo xinput set-prop 9 "Evdev Axis Calibration" 75, 1977, 105, 1860
created a *.service file in /etc/systemd/system/gdm.target.wants:
[Unit]
Description=Calibrates the touchscreen
[Service]
ExecStart=/home/sam/calibration.sh
[Install]
WantedBy=gdm.target
Then I enabled the service and restarted the computer. The service did not calibrate the touchscreen on boot (wheel with no password is enabled in sudoers for test purposes) and I had to log in in order to run the script. Then, when I logged out again, it reset the calibration making it impossible to use the gdm login without a keyboard.
DE: Dann habe ich den Systemdienst aktiviert und den Computer neu gestartet. Der Dienst hat nicht den Touchscreen bei booten kalibriert (wheel ohne Passwort in sudoers zu Testzwecken aktiviert) und ich musste einloggen, um das Skript auszuführen. Dann, wenn ich wieder abgemeldet hat, has es die Kalibrierung wiederhergestellt, und das gdm Login ohne echtes Tastatur unmöglicht.
This is clearly not the best way to deal with the problem. Has anybody else gotten this to work?
DE: Das ist auf jeden fall nicht das beste möglichkeit um das Problem zu melden. Hat jemand dieses Problem meldet?
EDIT: Falls sie nur Deutsch verstehen kann, hab ich das deutsche Übersetzung von Google Übersetzer oben und ein paar Fehler davon korrigiert. Ja, ich bin faul. lol
Last edited by kg6zvp (2013-02-14 19:15:42)Thanks for your link but i don't think it has something to do with relinking libraries since i never had to to that on my first machine. I'm currently pursuing a different approach: I'm comparing the files used by ccpd and cups on both machines with each other. These are the results:
On the machine with working capt service:
http://pastebin.com/Fyif7zxz
http://pastebin.com/n0KQj14z
On the machine with defect capt service:
http://pastebin.com/rtUW5Gfm
http://pastebin.com/vh94E3Jv
One thing that i noticed is the two libraries resolv and nss which are used on the defect machine. Could it be that?
Last edited by Picoli (2013-02-24 22:49:25) -
I need help getting my Intuos5 to work with Flash CS6
Can someone give me some help with this? I can't find a single thing on Google that helps me.
I installed Adobe Flash CS6 recently and I have been using my Intuos5 Large for a long time now with Photoshop CS6. The thing is, with Photoshop, it took forever to get working properly. It turned out that I needed to use the 64-bit version because my 64-bit system and tablet drivers won't work with 32-bit Photoshop.
Concerning Flash, it's the same problems as Photoshop. It refuses to recognize my tablets functions such as pressure and tilt sensitivity. It also has an annoying lag or lack of response if I do small, quick strokes. I would switch Flash to 64-bit mode, but there isn't one. I can't find the little stroke-like icon in Flash to turn on sensitivity either. I'm really confused. I've tried it with Flash CS5.5 and it's the same thing.
That's my issue, and I have tried restarting the software and rebooting many times as well. There doesn't seem to be much for options. This all leads to it probably being a 64-bit and 32-bit compatability issue
I'm running Windows 7 with more than enough power to maintain Flash CS6. It is possible that I may need to update my tablet driver since I did for Photoshop CS6, but it was a pain in the *** getting Photoshop to work until I used 64-bit mode. I may need additional files to mod the software.
I would really appreciate the help so I can begin to learn animation. It's my passion. Thanks, in advance.
Here are my relevant specs:
System Information
Time of this report: 9/4/2012, 01:32:48
Machine name: LAPPY_TOPPY
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.120503-2030)
Language: English (Regional Setting: English)
System Manufacturer: TOSHIBA
System Model: Satellite L675
BIOS: Phoenix SecureCore Version 2.30
Processor: Intel(R) Core(TM) i5 CPU M 450 @ 2.40GHz (4 CPUs), ~2.4GHz
Memory: 4096MB RAM
Available OS Memory: 3954MB RAM
Page File: 2016MB used, 5890MB available
Windows Dir: C:\windows
DirectX Version: DirectX 11
DX Setup Parameters: Not found
User DPI Setting: Using System DPI
System DPI Setting: 96 DPI (100 percent)
DWM DPI Scaling: Disabled
DxDiag Version: 6.01.7601.17514 64bit Unicode
Display Devices
Card name: ATI Mobility Radeon HD 5650
Manufacturer: ATI Technologies Inc.
Chip type: ATI display adapter (0x68C1)
DAC type: Internal DAC(400MHz)
Device Key: Enum\PCI\VEN_1002&DEV_68C1&SUBSYS_FD001179&REV_00
Display Memory: 2735 MB
Dedicated Memory: 1014 MB
Shared Memory: 1721 MB
Current Mode: 1600 x 900 (32 bit) (60Hz)
Monitor Name: Generic PnP Monitor
Monitor Model: unknown
Monitor Id: LGD01CA
Native Mode: 1600 x 900(p) (60.080Hz)
Output Type: InternalIf you are moving from an existing Mac to a new Mac the easiest thing to do is connect the two Macs via a Firewire cable and run the Migration assistant. If you are moving files from a Windows platform or you don't want to use the Migration assistant review this article.
http://docs.info.apple.com/article.html?artnum=300173
Maybe you are looking for
-
Cannot delete more than 4 e-mails from trash folder in one go
When I try to delete more than 4 e-mails in one go from the trash folder on my Sony Xperia Z2, the e-mail software crashes with the message: 'Unfortunately, E-mail has stopped'. Is this a bug everyone is experiencing on the Z2?
-
I am facing problem with adobe illustrator cc in windows 8,it closes automatically after few secons,please help [ link removed by moderator ]
-
Question about photo slideshow
When you have a photo page, is there a way to eliminate being able to click on a photo to enlarge it? I'd just like to have people scroll down to look at my photos, instead of the option of clicking on one and going through a slideshow. I know you ca
-
Import folder structure. Incorrect date on folders.
I'm trying to import a bunch of jpg photos taken in 2006 and 2007 to my Aperture 3 library. I use a referenced library in my pictures folder and I would like the files to be copied to new folders named after the year, month and day they were taken. H
-
We're using SharePoint 2010, I'm the system admin for a SharePoint farm. We enabled SharePoint Search by adding a Search Service APplication. One of the crawl report timer job is failing every 5 minte with the error "Cannot connect to remote server".