EGalax Touchscreen Detected But Not Working

I installed Arch Linux x64 in Lenovo S400 Touch, it has a "eGalax Inc. eGalaxTouch" Thouchscreen, i have tried most of the thread, yet i cant figure out how to get it to work!
Here is the output from lsusb
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 04f2:b420 Chicony Electronics Co., Ltd
Bus 001 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. RTS5129 Card Reader Controller
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 002: ID 0eef:a107 D-WAV Scientific Co., Ltd
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Here is the output from Xorg Log
[ 33.081] (II) config/udev: Adding input device eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00 (/dev/input/event5)
[ 33.081] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Applying InputClass "evdev touchscreen catchall"
[ 33.133] (II) systemd-logind: got fd for /dev/input/event5 13:69 fd 15 paused 0
[ 33.134] (II) Using input driver 'evdev' for 'eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00'
[ 33.134] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: always reports core events
[ 33.134] (**) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Device: "/dev/input/event5"
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Vendor 0xeef Product 0xa107
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Found absolute axes
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Found absolute multitouch axes
[ 33.134] (II) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: No buttons found, faking one.
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Found x and y absolute axes
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Found absolute touchscreen
[ 33.134] (II) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Configuring as touchscreen
[ 33.134] (**) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: YAxisMapping: buttons 4 and 5
[ 33.134] (**) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 33.134] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.0/0003:0EEF:A107.0001/input/input6/event5"
[ 33.134] (II) XINPUT: Adding extended input device "eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00" (type: TOUCHSCREEN, id 9)
[ 33.134] (II) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: initialized for absolute axes.
[ 33.135] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: (accel) keeping acceleration scheme 1
[ 33.135] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: (accel) acceleration profile 0
[ 33.135] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: (accel) acceleration factor: 2.000
[ 33.135] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: (accel) acceleration threshold: 4
[ 33.135] (II) config/udev: Adding input device eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00 (/dev/input/mouse0)
[ 33.135] (II) No input driver specified, ignoring this device.
[ 33.135] (II) This device may have been added with another device file.
[ 33.136] (II) config/udev: Adding input device Lenovo EasyCamera (/dev/input/event12)
[ 33.136] (**) Lenovo EasyCamera: Applying InputClass "evdev keyboard catchall"
[ 33.136] (**) Lenovo EasyCamera: Applying InputClass "system-keyboard"
[ 33.137] (II) systemd-logind: got fd for /dev/input/event12 13:76 fd 16 paused 0
[ 33.137] (II) Using input driver 'evdev' for 'Lenovo EasyCamera'
Here is the output from xinput --list
xinput --list
⎡ Virtual core pointer id=2 [master pointer (3)]
⎜ ↳ Virtual core XTEST pointer id=4 [slave pointer (2)]
⎜ ↳ eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00 id=9 [slave pointer (2)]
⎜ ↳ SynPS/2 Synaptics TouchPad id=13 [slave pointer (2)]
⎣ Virtual core keyboard id=3 [master keyboard (2)]
↳ Virtual core XTEST keyboard id=5 [slave keyboard (3)]
↳ Power Button id=6 [slave keyboard (3)]
↳ Video Bus id=7 [slave keyboard (3)]
↳ Power Button id=8 [slave keyboard (3)]
↳ Lenovo EasyCamera id=10 [slave keyboard (3)]
↳ Ideapad extra buttons id=11 [slave keyboard (3)]
↳ AT Translated Set 2 keyboard id=12 [slave keyboard (3)]
Here is the output from xrandr
Screen 0: minimum 8 x 8, current 1366 x 768, maximum 32767 x 32767
LVDS1 connected primary 1366x768+0+0 (normal left inverted right x axis y axis) 309mm x 173mm
1366x768 60.10*+
1024x768 60.00
800x600 60.32 56.25
640x480 59.94
DP1 disconnected (normal left inverted right x axis y axis)
HDMI1 disconnected (normal left inverted right x axis y axis)
VGA1 disconnected (normal left inverted right x axis y axis)
VIRTUAL1 disconnected (normal left inverted right x axis y axis)
Here is the output of lsmod
Module Size Used by
fuse 87590 3
ctr 12927 2
ccm 17534 2
coretemp 12820 0
hwmon 12930 1 coretemp
intel_rapl 17605 0
iosf_mbi 12682 1 intel_rapl
arc4 12536 2
brcmsmac 536435 0
cordic 12352 1 brcmsmac
brcmutil 13136 1 brcmsmac
b43 414640 0
mac80211 648753 2 b43,brcmsmac
x86_pkg_temp_thermal 12951 0
intel_powerclamp 17122 0
cfg80211 476584 3 b43,brcmsmac,mac80211
kvm_intel 143417 0
uvcvideo 84822 0
snd_hda_codec_hdmi 49263 1
ssb 65506 1 b43
rng_core 12808 1 b43
videobuf2_vmalloc 13286 1 uvcvideo
videobuf2_memops 12519 1 videobuf2_vmalloc
videobuf2_core 39635 1 uvcvideo
pcmcia 53108 2 b43,ssb
v4l2_common 12814 1 videobuf2_core
videodev 135040 3 uvcvideo,v4l2_common,videobuf2_core
pcmcia_core 18431 1 pcmcia
media 18365 2 uvcvideo,videodev
joydev 17063 0
snd_hda_codec_realtek 67322 1
snd_hda_codec_generic 63161 1 snd_hda_codec_realtek
rtsx_usb_ms 16899 0
memstick 13696 1 rtsx_usb_ms
bcma 46203 3 b43,brcmsmac
mousedev 17272 0
r8169 76869 0
kvm 435299 1 kvm_intel
mii 12675 1 r8169
iTCO_wdt 12831 0
iTCO_vendor_support 12649 1 iTCO_wdt
crct10dif_pclmul 13394 0
crc32_pclmul 12915 0
shpchp 35210 0
snd_hda_intel 26387 3
snd_hda_controller 26857 1 snd_hda_intel
ideapad_laptop 17447 0
snd_hda_codec 112621 5 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
ac 12715 0
crc32c_intel 21809 0
psmouse 107442 0
snd_hwdep 17244 1 snd_hda_codec
snd_pcm 88779 4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel,snd_hda_controller
snd_timer 26614 1 snd_pcm
snd 73436 14 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel
ghash_clmulni_intel 12978 0
thermal 17559 0
cryptd 18553 1 ghash_clmulni_intel
pcspkr 12595 0
serio_raw 12849 0
battery 17452 0
mei_me 17987 0
mei 75468 1 mei_me
soundcore 13031 2 snd,snd_hda_codec
sparse_keymap 12818 1 ideapad_laptop
rfkill 18867 3 cfg80211,ideapad_laptop
i2c_i801 16965 0
evdev 21544 13
lpc_ich 20768 0
mac_hid 12633 0
processor 27777 0
sch_fq_codel 17343 6
ext4 514390 1
crc16 12343 1 ext4
mbcache 17171 1 ext4
jbd2 86379 1 ext4
rtsx_usb_sdmmc 25280 0
led_class 12855 3 b43,brcmsmac,rtsx_usb_sdmmc
mmc_core 110613 3 b43,ssb,rtsx_usb_sdmmc
rtsx_usb 17487 2 rtsx_usb_sdmmc,rtsx_usb_ms
hid_multitouch 17057 0
usbhid 48596 0
hid 110513 2 hid_multitouch,usbhid
sd_mod 43575 2
atkbd 22254 0
libps2 12739 2 atkbd,psmouse
ahci 33248 1
libahci 27215 1 ahci
libata 181461 2 ahci,libahci
xhci_pci 12675 0
ehci_pci 12512 0
scsi_mod 147395 2 libata,sd_mod
xhci_hcd 152471 1 xhci_pci
ehci_hcd 69979 1 ehci_pci
usbcore 199382 7 uvcvideo,rtsx_usb,ehci_hcd,ehci_pci,usbhid,xhci_hcd,xhci_pci
usb_common 12561 1 usbcore
i8042 18002 2 libps2,ideapad_laptop
serio 18282 6 serio_raw,atkbd,i8042,psmouse
i915 1002518 3
button 12953 1 i915
intel_gtt 17848 1 i915
i2c_algo_bit 12744 1 i915
video 22205 1 i915
drm_kms_helper 98881 1 i915
drm 273079 5 i915,drm_kms_helper
i2c_core 50240 7 drm,i915,i2c_i801,drm_kms_helper,i2c_algo_bit,v4l2_common,videodev
I have blacklisted "usbtouchscreen" module
It seems to be detected, but i have no idea how to make it work, it isnt even registering any kind of touch event, i even tried installing eGalax driver from AUR, it still didnt work.
Please help me by pointing me in the right direction!
Any help is appreciated. Thank you!
Last edited by kshergil (2015-04-20 19:08:28)

i posted output of that command without starting X
Here is complete output after starting X
[samtech@M4800 ~]$ journalctl -b | grep -i bluetooth
Dec 10 21:37:45 localhost kernel: Bluetooth: Core ver 2.19
Dec 10 21:37:45 localhost kernel: Bluetooth: HCI device and connection manager initialized
Dec 10 21:37:45 localhost kernel: Bluetooth: HCI socket layer initialized
Dec 10 21:37:45 localhost kernel: Bluetooth: L2CAP socket layer initialized
Dec 10 21:37:45 localhost kernel: Bluetooth: SCO socket layer initialized
Dec 10 21:37:45 localhost kernel: Bluetooth: hci0: read Intel version: 370710018002030d00
Dec 10 21:37:45 localhost kernel: Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.80.2.3.d.bseq
Dec 10 21:37:45 localhost kernel: Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
Dec 10 21:39:12 localhost NetworkManager[308]: <info> Loaded device plugin: /usr/lib/NetworkManager/libnm-device-plugin-bluetooth.so
Last edited by samtech09 (2014-12-10 16:52:30)

Similar Messages

Flash plugin detected but not working (Firefox 22 on Linux)

Hi all,
I can't get the flash plugin to work. It's installed, detected in about:plugins, but when I visit adobes's test page at http://www.adobe.com/fr/shockwave/welcome/ , I just get the usual " you need a plugin to view this content" thing.
This happenned since I migrated from Mageia 1 to Mageia 2, and still doesn't work on Mageia 3, which uses Firefox 17 ESR. I then downloaded and installed Firefox 22 directly from Mozilla, still with no luck. I've reset my profile, tried to use an empty profile, tried disabling all add-ons, still no luck.
about:plugins displays this:
File : libflashplayer.so
Path : /opt/firefox/browser/plugins/libflashplayer.so
Version : 11,2,202,297
State : Enabled
Shockwave Flash 11.2 r202
This is the most up-to-date flash version available from Adobe.
Another thing is that this machine is a 32 bits install, on an Athlon XP 3000+ with a Radeon X1650 graphics card. Surprisingly, on another machine, using the same distro but with a 64 bits install, Flash works well.
I'm out of ideas now, so any hint would be welcome. Thank you.

Shockwave also known as Shockwave for Director is not the same as the Shockwave Flash Player.
*https://support.mozilla.org/kb/Using+the+Shockwave+plugin+with+Firefox
*https://support.mozilla.org/kb/Managing+the+Flash+plugin
You can test the Flash plugin here:
*http://www.adobe.com/fr/software/flash/about/
*http://www.adobe.com/software/flash/about/

External screen detected but not working on DisplayPort connection on X220

I'm running up to date Raring on my Thinkpad X220 and stumbled upon weird problem.
I can connect to an external 24 inch DELL U2312HM external screen using DisplayPort cable.
I tried the same connection at work, with similar, but larger screen - 27 inch DELL U2713HM using the same cable.
When I check >>Settings >> Displays the display is detected. However I'm looking at dark screen.. Bizarrely - when I hit the PrtScr - I can also see it correctly with Ubuntu walpaper o_O
The monitor is detected and works correctly when using [DisplayPort to DVI-D Adapter Cable (Single Link)] however the resolution on this setup is limited to 1920 x 1200 so I'd really like to take advantage of DVI since the laptop should support it.
How could I fix this issue?

Hello,
According to the specs on Dell's web site, the U2713HM is a WQHD (2560×1440) resolution display and requires a DisplayPort 1.2 compliant signal. From looking at the PSREF documentation, this resolution is supported on the DisplayPort at a frequency of 60Hz. There is no mention of DisplayPort version, though.
Just to confirm, the DisplayPort cable you are using is DisplayPort at both ends and does not have an HDMI or DVI connector attached to the monitor, correct?
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

[SOLVED] Epson flatbed scanner detected but not working

I have an Epson V330 scanner which used to work with iscan and iscan-data from AUR. Now the scanner is detected correctly by lsusb, sane-find-scanner, and scanimage -L, but if I run
scanimage > image/pnm
I get
sane_start: Invalid argument
xsane brings up the scanner but it gives the same error.
I think the problem may be related to the fact that there is no /dev/scanner0 or anything similar, which I think there should be. I've tried rebooting with the scanner switched on but no result.
Last edited by acampbell (2014-07-05 15:34:17)

Thanks so much - yes, that was it! I had to reinstall my system last month and I forgot that I'd been caught out by that one previously. Now working.

When i plug in my ipod nano (6th generation) a message comes up saying it's 'detected but not identified' i've spend like all day trying to solve it, uninstalled it, reinstalled it and nothing seems to work..

when i plug in my ipod nano (6th generation) a message on itunes saying the ipod is 'detected but not identified'- i've spent all day trying to fix it and nothing seems to work so i can't sync any songs..

Hello beafraser,
Here's an article to help troubleshoot when your iPod is detected but not identified.
iPod nano: Error message saying that iPod 'could not be identified properly'
http://support.apple.com/kb/ts3218
Hope that helps.
Thank you for visiting Apple Support Communities.
Nubz

IPod Nano 6th Gen detected but not recognized

Since recently, my IPod is not being recognized by iTunes (11.1.4.62 ). The error says that it is detected but not be identified properly. I went through all the troubleshooting steps including resetting my ipod, re-starting the driver, re-installing iTunes but nothing works. Interestingly, if iTunes is not open, I can see the iPod as a storage device, I can open and browse it. So I assume there is no error with the wire, the iPod itself or the driver. As soon as iTunes gives the above error, it stops being visible as a storage device. How can I fix this?

Aridra,
Thanks very much for this - I had exactly the same problem; went through the same steps to no avail unitl I read your post. Similarly, I uninstalled EVERYTHING Apple on my PC and re-installed. Bingo !! my iPod is now recognised and synched.

IPhone Detected But Not Identified?

I hooked up my iPhone to my base that goes into my cpu and I got this message: "An iPhones was detected, but could not be identified properly. Please disconnect and reconnect the iPhone and try again." I havent had any problems like this before. Will a reinstall over this iTunes fix the problem? I am running Windows XP. I have also noticed that when I plug up my phone, the Scanner and Camera Wizard pops up recognizing the iPhone as a camera. Also when running iTunes after I got that message, my cpu will freeze for about 5 seconds and work fine a little while then freeze again for 5 seconds. But when I close iTunes, it stops freezing.

I am having the same issue iPhone detected, but not identified. Did you get a solution to the problem? Had to go to th Apple store to register my phone. iPhone connected fine with their MacBook. That doesn't help me at home though.

Updated my iphone 3gs, lost my music and apps, they are backed up on itunes, how do I move them back to my phone, tried to sync but not working, please help

Updated my iphone 3gs, lost my music and apps, they are backed up on my computer but i cannot move them over to my phone, tried to sync but not working, please help

well first make sure that when you click on the name of your iphone on the left hand side of itunes that you go to the app and music tab and check mark the sync apps and sync music. then try clicking apply in the bottom right hand corner. then if not try doing it again after going to prefrences in the top menu and going to devices tab and click reset sync history if that doesnt work with music try and drop and drag to the name of your iphone, lastly if that doesnt work you can try restoring from a backup from before you updated. it will keep the new software but put everything that was on your phone when you created the backup back onto your phone.
http://support.apple.com/kb/HT1351 for syncing music

I have CS5 and a d-600. I would like to use camera raw but not working. I downloaded CR 7.3 and still not working. Do I need to upgrade to CS6 ..or just throw it all out the window and get rid of my d-600 ?

I have CS5 and a d-600. I would like to use camera raw but not working. I downloaded CR 7.3 and still not working. Do I need to upgrade to CS6 ..or just throw it all out the window and get rid of my d-600 ?

it allows you to use your cr files, Adobe - Adobe Camera Raw and DNG Converter : For Windows
Camera Raw: How to use Adobe DNG Converter - YouTube

Camera Raw 5.1 downloaded and unzipped but not working in CS4. Can't open Nikon D90 NEF files.

Camera Raw 5.1 downloaded and unzipped but not working in CS4. OS Windows 7. Can't open Nikon NEF files. Camera Nikon D90.

update the adobe program that needs cr 4.6+, http://www.adobe.com/downloads/updates/

Hi I'm trying to purchase but not working

Hi I'm trying to purchase but not working. It's telling me to contact apple support. I bought today one time but I can't buy again. I contact the bank and they said there is nothing wrong from their side so the problem only with the apple store. Please advice.

iTunes and App store
Contacting the iTunes store
Phone: 800-275-2273 How to reach a live person: Press 0 four times
Hours of Operation: Mon-Fri: 9am-5pm ET
Email: [email protected]

Update to 10.6.8 and HP F2100 and D2400 Printers stopped working. Restored 10.6.7 and printers from Install CD's but not working, Same with scanner

Help....
Updated to 10.6.8 and HP F2100 and D2400 Printers stopped working.
Restored 10.6.7 and printers from Install CD's but not working.
Same with F2100 scanner
Am I glad I kept Windows desktop as without it I would be scre**ed now
What is going on with this latest update as its like a return to Windows with things crashing or hanging up every few minutes????
On a MacBook Air that has not been updated everything still works so what has 10.6.8 done and why won't the restore to 10.6.7 work?
Steve

None of those things you mentioned were what I suggested.
I'm guessing the "ctrl click in printer preferences" means you Reset the Printing System?
If so, that is what I would have suggested if deleting it by selecting the ( - ) button and then adding it with the ( + ) button.
But, if HP has a fix, it likely needs to update its drivers.

HT201210 trying to download an instal ios 7 on my iphone 4s, after half an hour into the download it came up with a message saying failed and everytime i try again the download doesnt start. tried downloading from itunes aswel but not working. anyone know

trying to download an instal ios 7 on my iphone 4s, after half an hour into the download it came up with a message saying failed and everytime i try again the download doesnt start. tried downloading from itunes aswel but not working. anyone know why?

The servers are overloaded. There are a hundred million people all trying to download iOS 7 at one time. Try again later

Android kitkat issue in loading swf file from device. URL found but not working

Hi,
I am facing one issue from a very long time regarding file access in Android Kitkat version 4.4.*. I have developed Adobe Air player application for android and it is working as expected below kitkat version but not on kitkat.
I am following this methods -
NativeApplication.nativeApplication.addEventListener(InvokeEvent.INVOKE, onInvoke);
public function onInvoke(event:InvokeEvent):void
                                    var newFile:String = String(event.arguments[0]);
                                    trace("Received new file from Android: "+newFile)
Received URL form device in Android Kitkat -
/storage/emulated/0/.iProfData/swf/playListFiles/ContentCreation/Ma_V2_522/en/Animation/27 031_1_Welcome screen.swf
file:////storage/emulated/0/.iProfData/swf/playListFiles/ContentCreation/Ma_V2_522/en/Anim ation/27031_1_Welcome screen.swf
                - Loading this URL using loader class in AS3 AIR but not working.
file%3A///storage/emulated/0/.iProfData/swf/playListFiles/ContentCreation/Ma_V2_522/en/Ani mation/27031_1_Welcome%20screen.swf
       - Have used also by doing escape character but still it is not working showing file not found both SWF and mp4 case. (Mp4 case NetStream.Play.FileNotFound)
By using the above methods I can have swf or mp4 video url but when I am loading it, It is not working giving error message "File not found/ IO Error". I have read that if use escape character then it will work but I have used escape character also but it is not working.
Humble request you to please advise how can I solve this issue.
Best regards,
Sunil Kumar

Starting in KitKat, Google requires that applications have permission to access files on the system. You must specifically add either the READ_EXTERNAL_STORAGE or WRITE_EXTERNAL_STORAGE permissions in order to access files. Adding either one of those permissions should let you read/access files on the device. Prior to KitKat, you didnt have to have these permissions listed in the manifest to access files.

Page is working ok in chrome and IE but not working in firefox. jquery problem i guess

http://184.170.251.149/raschet-shkafa-kupe
this page is working correctly in chrome and IE but not working in firefox, i cant click and of the dropdown menus(ДСП, доличество дверей). it was working perfectly prior firefox 18. can you please fix the compatibility problem ?

I was referring to the second page in my above post.
I disabled JavaScript as a test after loading the page with JavaScript enabled and that worked.<br />
I also get the selects to open if I right-click instead of left-click the select.<br />
That way the select get selected (shows a focus ring) and after that left-clicking works as well .
This assumes that JavaScript is monitoring the left-click, but that script no longer works properly.
A good place to ask advice about web development is at the MozillaZine "Web Development/Standards Evangelism" forum.
*http://forums.mozillazine.org/viewforum.php?f=25
The helpers at that forum are more knowledgeable about web development issues.<br>
You need to register at the MozillaZine forum site in order to post at that forum.

EGalax Touchscreen Detected But Not Working

Similar Messages

Maybe you are looking for