EGPU solution if possible.

So I'm using my laptop as a "Slave" if that's the correct term for it. 
Basically I hooked it up to my 27" monitor through HDMI so I can get full 1080P resolution, as well as connecting a wireless keyboard and mouse to it.
Now, my laptop is an HP Envy DV7 7270CA, that comes with an Nvidia GT630M GPU. It's not a bad GPU, especially for a consumer grade laptop, but I find it a bit lackluster, even at 1600 x 900 resolution, let alone 1920 x 1080. 
I've read about eGPU in the past, and I was wondering if it was possible with my laptop. It doesn't have to be discreet or neat or anything, just anything that works. Even if I use a GTX650 Ti or something like that. Just anything that would be an upgrade to what I have. Now I understand that gameplay > graphics, but if I can have both, why not? I'd just like a more immersive experience when I play some games.
If I could upgrade my chipset from a 630M to a 650M, I would, but I heard that's more impossible than surviving in the detonation zone of a nuke. 
Any help would be greatly appreciated. Thank you.
This question was solved.
View Solution.

Hi,
Well, you are talking about EXTERNAL video cards for laptops here and your "PLAN" is to use normal highend desktop cards. From my understanding: not many laptops have PCIe x16 and few other things therefore if you wish to test you  msy need:
(a) A converter to connect normal MXM slot to external PCIe x16 connector,
(b) Power supply for the  external card. No way you can draw enough power from your laptop to a highend external video card.
(c) Hardware to mount your external video card ...
Good luck.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

  • HT201441 I do not know the old owner please email His solution is possible the old phone to communicate with him

    I do not know the old owner please email His solution is possible the old phone to communicate with him

    Apple will never release personal information about you or anyone else to any consumer.  It is your responsibility to verify the device before purchasing it if you choose to go through a third party.  Recommendation: Buy Apple products from an authorized reseller.
    You are experiencing Activation Lock.  If the previous owner will not remove the device from their account there is nothing you can do unless the place you purchased it from will give you a refund.
    Activation Lock: http://support.apple.com/kb/ht5818
    What if I purchase a device that is still linked to the previous owner's account?
    Contact the previous owner as soon as possible and ask them to erase the device and remove it from their account. For complete instructions, read how to remove a device from a previous owner's account.
    How do I check for Activation Lock before purchasing a used device?
    When purchasing an iPhone, iPad, or iPod touch from someone other than Apple or an authorized Apple reseller, it is up to you to ensure that the device has been erased and is no longer linked to the previous owner’s account.
    Follow each of these steps to make sure that you can use the device you purchase:
    Turn the device on and slide to unlock.If the passcode lock screen or the home screen appears, the device has not been erased. Ask the seller to completely erase the device by going to Settings > General > Reset > Erase All Content and Settings. Do not take ownership of any used iPhone, iPad, or iPod touch until it has been erased.
    Begin the device setup process.After choosing a language, choosing a country, and connecting to a network, the device will begin activation. If you are asked for the previous owner’s Apple ID and password, the device is still linked to their account. Hand the device back to the seller and ask them to enter their password. If the previous owner is not present, they can remove the device from their account by signing in to icloud.com/find. Do not take ownership of any used iPhone, iPad, or iPod touch until it has been removed from the previous owner’s account.
    You will know that a device is ready for you to use when you are asked to “Set up your iPhone", “Set up your iPad", or “Set up your iPod” during the device setup process.

  • Autom. replication of EarlyWatch Alerts in 2nd Solution Manager possible?

    Hi experts,
    I just received a question from a customer whether it is possible to automatic replicate EarlyWatch Alerts generated for systems in SolMan A to SolMan B without having all satellite systems connected to SolMan B.
    There are two reports available I know: BDL_GET_SESSION_DATA and BDL_GET_DATA_AND_CREATE_SESSIO
    At least via the last report it is possible to read the session number in SolMan A and create a new session with this data in SolMan B. But it is not possible to assign the sessions to a solution or run it as daily job...
    Do you know if there is such a functionality in SAP standard or do we need to build our own solution here?
    Regards, Richard

    Hello,
    This is how you genrate an EWA for on Satellite system in two Solution Manager systems.
    One will be created automatically via the Maintenance Package (providing you followed best practices) or periodic EarlyWatch of Solution Manager Task if you are not follwoing best practices.
    Say we have Solution Manager A & B. In SDCCN in RFC Destinations, we define Solution Manager A as the Master.
    So this will be where the EWA task created by the Maintenace Package task will be sent.
    For the Solution Manager B you created a Earlywatch periodci task, only you make the RFC Destination the SM<SID>CLNT<NO#>_BACK (where the SID is the SID of Solman B) Yoy can refer to SAP NOTE 207223, which is the Note that explains how to send an EWA to SAP. Its the exactsame process, but the destination is changed to the second Solution Manager.
    The data comes from the Satellite/managed system, but can be directed to different destinations.
    But you can't send the data from Solution Manager A to Solution Manager B.
    You can send the data to Solution Manager A & B and process the data on A and on B, or any other Solman system.
    Regards,
    Paul

  • My Copy/Cut and Paste Solution (if possible)

    I sent this to Apple:
    I know there's been a lot of people saying they need/want a cut/copy & paste feature.
    I was thinking about this tonight and realized that with a touch screen that needs to control a lot, incorporating "clicking and dragging" becomes somewhat a challenge. I don't know if it's possible to do with a software update (through iTunes) but here two ideas...
    First, in either idea, a "copy arrow" would need to be included in the touch keyboard. It would look like a cursor key arrow pointing to the right.
    Idea #1 - Cursor arrow is a "sticky" key, so you hit it once and it stays selected until you hit it again.
    Using a finger or the cursor magnifying glass, the user could place their cursor at the beginning of the text they want to highlight. They then click on the sticky arrow key. Using a finger or the cursor magnifying glass they place the cursor at the end of the text they want to highlight. The text now shows highlighted. Click the sticky arrow key again to copy the text and clear the highlight.
    Idea #2 - Cursor arrow highlights as it's selected.
    Using a finger or the cursor magnifying glass, the user places their cursor at the beginning of the text they want to highlight/copy. They then click on the copy arrow key (or hold it down) until they reach the end of the text they wish to copy. As they highlight, content highlighted is copied to the clipboard automatically. Clicking anywhere on the screen clears the highlight (and retains what is highlighted on the clipboard).
    Being Apple, you may have a more elegant solution than me... but I thought I'd share it none-the-less.
    What do you think?

    I was going to cut and paste part of another post about this but...
    I think that th simplest initial implementation of copy/cut/paste is to have a clipboard icon that turns on a selection function with its own pallete of keys. (cut, copy, paste, select all, select none, delete selection, and my favorite desperately needed button... copy to notes)
    Once in clipboard mode, single tap selects a ord, double tap selects a sentence, triple tap selects the paragragh, and a select all button selects the entire text within the frame.
    Perhaps there should also be a button that looks like your cursor with the arrow. however, it would have to be set to highlight from one complete word to another and not from the exact point of touch.
    Man do I wish that I could copy and paste this into my own post from earlier.

  • Readonly Access to Solution Manager possible?

    Hello experts,
    at the moment we are using Solution Manager mainly for managing the
    system landscape and projects/Business blueprint.
    My question, which role needs to be assigned if we want to give a user
    readonly access to projects (RMMAIN)?
    In RMMAIN is it possible to give readonly access to one project and
    change access to another project?
    Is it possible to give full readonly permission to the Solution Manager?
    Thanks a lot in advance for your help,
    Manfred

    Thanks for your help.especially the mentioning of the object S_PROJECT proved to be invaluable!
    However, in the end some-else suggested to use the solution manager display role SAP_SOL_RO_COMP. This is a composite role holding all (or at least the most important) display roles regarding SOLMAN. I then just copied these single roles to my namespace and adjusted the S_PROJECT field according to my needs. Then I assigned these roles to the target user.
    Thanks again for your help,
    Best regards
    Manfred

  • Solution (or possible) to Undetected Ipods!

    Important note: The author of this message doesn't have english as its natal languaje, so there may be some errors especially on verb conjugations.
    Continue reading:
    I had the same problems with my brother's new incredible Ipod Video.
    He almost not know something about the use of computers so i have to make the hard work for him.
    I said him it was unnecesarily to install the CD 'cause i already made it for my old Ipod mini. So i connected his ipod but did not open itunes.
    After upgrading to SP2, Reinstalling Itunes, totally uninstalling ipod and itunes, reinstalling, etc. i decided to go a little deeper. So i copied some system files from my Mini to the Video, but was'nt the solution.
    Then i went to Manage Drives, from right-click on My PC, Manage> Manage Drives, and interchanged the drive letter of our ipods (Video from C to I and Mini from I to F). In my very special case i used to have a drive on C. But it had some MBR problems (nothing to do with this, only details) so i disconnected it physically from the PC (it was an EIDE HDD). So when i plug the Video it gets assignated "C" as it drive letter. So you just have to play around the drive letters and you'll see how it gets detected by Itunes.
    I too got very frustrated with this ipod, started to think that it was a nightmare instead a dream, and that apple is not giving the apropiate support for it (even less here in Mexico where this Ipod hasn't been officially released). But that was my very personal problem and im pretty sure the one of yours. By the way, the part of copying files was just a story-part of my experience, you dont need actually to do this.
    Note 2: You dont need to restart after changing dive letter. You'll need administrator or super-user privileges to do this. And, give it some time, to itunes, to recognize it.

    HOLY COW!!!!
    I had to try twice but...when i changed my Drive to "M" it started working (from my primary machine!)!!!
    I don't understand what is going on AT ALL with this, but maybe...just maybe I have my mini back!

  • Blue screen solutions not possible; keyboad commands not working

    I am stuck in blue sceen limbo; can't go back to Tiger (wish I could), but can't run Leopard, either. The installation seemed to go smoothly, but all I get is a the blue screen and a sad little cursor with nothing to click. I looked up the official answer (article # 306857), but I am unable to restart in safe mode, as a target disk, or with the installation disk. The ONLY keyboard command that seems to work is the eject button to get the installation disk out. I am going to the "Genius" at my local Apple Store tomorrow, but I am already seething!

    Welcome to Apple Discussions!
    You may need an Apple wired keyboard (your Powerbook's built-in keyboard is one, if that's where you installed it) to go through the proper boot sequence.
    In the future when applying an update, follow these directions, and you shouldn't have more problems*:
    http://www.macmaps.com/upgradefaq.html
    - * Links to my pages may give me compensation.
    Message was edited by: a brody

  • What is the best solution to this problem?

    I have so many solutions in mind right now but i am looking for the best solution if possible. i have the following query
    SELECT one_query.date_required as Month_id,
               nvl(one_query.amount_used, 0) as overalluserhours_A,
                  nvl(second_query.amount_used_b, 0) as overalluserhours_B,
                  nvl((trunc(((second_query.amount_used_b/one_query.amount_used) * 100), 2)), 0) as p_change
    from
                 (select to_char(b1.needed_date,'YYYY-MM') as date_required,
                    SUM(b1.amount_used) as amount_used,
                      b1.type_id as type_id
                        from table_one b1
                         where b1.zone_type like 'NEWYORK%'
                         and b1.type_id = 'CARS'
                        and trunc(b1.needed_date) between to_date('2009-01-01', 'YYYY-MM-DD') and to_date('2009-12-31', 'YYYY-MM-DD')
                              group by to_char(b1.needed_date,'YYYY-MM'), b1.type_id) one_query,
                (select to_char(b2.needed_date, 'YYYY-MM') as date_required,
                                SUM(b2.amount_used) as amount_used_b,
                                       b2.type_id as type_id
                                    from table_one b2
                                       where b2.zone_type like
                                       'CHICAGO%'
                                  and b2.type_id = 'BIKES'
                                   and trunc(b2.needed_date) between to_date('2009-01-01', 'YYYY-MM-DD') and to_date('2009-12-31', 'YYYY-MM-DD')
                                 group by to_char(b2.needed_date, 'YYYY-MM'), b2.type_id)second_query
    where one_query.date_required = second_query.date_required(+);the above query is being used on table_one. The current problem I am having is based on the fact that table_one might sometimes contain data for only chicago and not for newyork. in this case, table_one would look like this
    identification_id         needed_date                   zone_type             type_id                  
    2                             3/22/2006 12:00:00          CHICAGO                BIKES
    3                              2/12/2006 12:00:00         CHICAGO                BIKEShowever though, in other case, it could be the other way around. in this case, table_one will look like this
    identification_id         needed_date                   zone_type             type_id                  
    4                            4/21/2007 12:00:00          NEWYORK                CARS
    5                             1/12/2007 12:00:00         NEWYORK                CARS
    and finally table_one could contain information for both cases. hence, we could have the following situation
    identification_id         needed_date                   zone_type             type_id                  
    6                            6/21/2008 12:00:00          NEWYORK             BIKES
    7                            8/12/2008 12:00:00         CHICAGO               CARSKindly note, my above query is currently being used inside a function. I know I can write so many if statement to handle but the main issue is regarding the fact, i am also using that query in another query which performs so many union all.

    I'm not sure how you're going to parameterize it, how those filters change from call to call, but an idea would be something like this:
    select date_required month_id,
           max(amt_used_chicago_bikes) overalluserhours_A,
           max(amt_used_newyork_cars) overalluserhours_B,
           (max(amt_used_chicago_bikes) / max(amt_used_newyork_cars)) * 100 p_change
      from (select zone_type,
                   to_char(b1.needed_date, 'YYYY-MM') as date_required,
                   b1.type_id as type_id,
                   SUM(case when zone_type like 'CHICAGO%' and type_id = 'BIKES'
                                 then b1.amount_used end) as amt_used_chicago_bikes,
                   SUM(case when zone_type like 'NEWYORK%' and type_id = 'CARS'
                                 then b1.amount_used end) as amt_used_newyork_cars
              from table_one b1
             where trunc(b1.needed_date) between
                   to_date('2009-01-01', 'YYYY-MM-DD') and
                   to_date('2009-12-31', 'YYYY-MM-DD')
             group by b1.zone_type,
                      to_char(b1.needed_date, 'YYYY-MM'),
                      b1.type_id)
    where amt_used_chicago_bikes is not null or amt_used_newyork_cars is not null
    group by date_required;Again, this is not the biggest concern regarding performance and certainly not the best way of doing it. Cracking those 250 lines of SQL and making it optimized would probably be the best way to approach the issue here.

  • Printing solution for KDE?

    I just wondered if anybody had a good work around for the print dialog problems in KDE (and presumably QT apps generally). I guess some distros patch the sources but this seems to require recompiling QT which I'm not keen to do and the patches are for an older version anyway.
    There are many references to the issue in both KDE and QT bug trackers e.g. https://bugs.kde.org/show_bug.cgi?id=180051.
    Basically, the issue is that the print dialog seems to have two parts. One part reflects the CUPS configuration for the printer. As far as I can tell the purpose of this part of the dialog is to sow confusion among users but perhaps that is not actually intentional. It seems, in any case, to have no effect whatsoever.
    The second part is some sort of QT print setup dialog. There are multiple issues with this. First, it is insensitive to the capabilities of the printer advertised by the PPD file via CUPS. So it doesn't matter whether the printer has fine-grained quality control in CUPS, it won't here. Likewise, it doesn't matter whether the printer can print colour or not, it will offer this option.
    So the first issue is that some settings just cannot be set through the dialog.
    The next issue is that this dialog uses defaults which do not depend on the defaults configured via CUPS. For example, no physical printer I use has letter paper; all of these are configured in CUPS to default to A4. But the print dialog defaults to letter paper. Similarly, CUPS is set to default to duplex and greyscale but the dialog defaults to single-sided in colour. Most of the printers I use do not even offer colour. Some of them need quality settings adjusted to get good output and this can't even be done via the dialog.
    This means that if I just print without reconfiguring via the dialog, I get "color, letter, single-sided" rather than "greyscale, A4, duplex, additional options".
    Finally, the configuration isn't saved. It must be done not only for each session or each application but for every single job sent from a KDE application and any other application which hooks into the KDE print framework. Every single job. KDE offers a GUI alternative to the CUPS web interface but I'm not sure why since it has zero affect.
    The result is obviously very irritating, time-consuming and wasteful of toner and trees.
    I'm therefore wondering how other people manage this issue or whether any workarounds are available which do not involve patching and compiling QT source. Apart from the issue of having to do that and having to do it on every update, the available patch even if it worked for QT 4.8.0 doesn't actually fix most of the above problems. It would not, for example, pick up the A4 default or enable me to set different quality settings.
    I'm wondering about trying to write some command line scripts but I'm not sure if this is the best solution so I'd like to know if better ones might be possible first. I'm not sure what the current best command line print command is although I figure that shouldn't be too hard to establish. But this would be very inconvenient for many applications. The only reason I'm considering it is because it wouldn't be too bad from Kile since the Konsole is right there anyway; and acroread doesn't rely on KDE for printing. Most of my printing is either kile -> okular -> print or acroread -> print. I'd still have issues with libreoffice, web browsers etc. so I'd rather find a more general solution if possible. (I know I can print to PDF and then print that but I might as well just go through the config unless I need quality settings in that case.)
    Or should I just buy a pencil?!

    SteveK wrote:I just have the one printer, although I have set it up in 2 or 3 different KDE distros and I'm just using normal Arch packages here.
    The reason I asked is because there are at least two patches available to fix the bug but they require compiling the whole of QT from source. Most distros, however, include these patches. So the fact that it works for you in another distro means nothing but the fact that it works for you in Arch is very, very interesting.
    The KDE developers don't seem to expect it to work. Discussion at https://bugs.kde.org/show_bug.cgi?id=180051 reveals that they think that Arch are "douchebags" for not patching QT. (Please note that I am *not* endorsing this view as the bug thread on KDE should make clear.)
    Unless, of course, they *are* patching it and something is weird about my config. How would I find that out?
    Oh and just to clarify, today I re-checked changing paper type between A4/Letter and colours to greyscale/colour as default settings, rebooted and the print dialogue reflected those changes, along with the printed output.  I have no idea why it works for some people and not others.
    My print dialog doesn't even reflect it 30 seconds later, let alone after a reboot! (And I reboot quite often so it isn't the lack of rebooting, either.)
    What about running from a terminal? Any related errors show up?
    Sorry for being dumb. How would I run it from the terminal? Or what would I run? Do you just mean start e.g. okular from terminal? I don't get anything interesting:
    okular <random-file>.pdf
    okular(24864)/kdecore (KConfigSkeleton) KCoreConfigSkeleton::writeConfig:
    okular(24864)/kdecore (KConfigSkeleton) KCoreConfigSkeleton::writeConfig:
    okular(24864)/kdecore (KConfigSkeleton) KCoreConfigSkeleton::writeConfig:
    okular(24864)/kdecore (KConfigSkeleton) KCoreConfigSkeleton::writeConfig:
    okular(24864)/kdecore (KConfigSkeleton) KCoreConfigSkeleton::writeConfig:
    okular(24864)/kdeui (kdelibs) KXMLGUIClient::~KXMLGUIClient: 0x8b9230 deleted without having been removed from the factory first. This will leak standalone popupmenus and could lead to crashes.
    I didn't actually print as I'm not connected to a printer right now, but I opened the print dialog, selected a printer and examined both "properties" and "options". The "advanced" properties always shows the CUPS defaults but they have no effect on anything. The "options", as usual, defaulted to letter/singe-sided/color etc.
    But perhaps that's not what you meant by "run from a terminal"?

  • Dev 6.0 with 8i possible ??

    Hi,
    We have a client specified project requirement as follows.
    1. The platform
    System need to work as atypical client server product with
    forms running on all machine (Windows environement).
    At the same time these forms should be deployable on the WEB
    using Oracle Web Application Server.
    2. The versions
    Oracle 8i 8.1.5
    Oracle Developer 6.0
    Oracle Web Application Server 4.0.7
    3. The problem
    a) We installed 8i clients and developer 6.0 client on all
    development machines. The Oracle 8i clients talk to the 8i
    server but the forms 6.0 does not talk to 8i server. We get the
    error message TNS service could not be resolved. I think this is
    because developer does not expect to talk to 8i it expects to
    talk to Oracle 8.0.5.
    b) Same problem for the Application server, while configuration.
    4. (Stupid) Questions
    a) Does Developer 6.0 work with 8i. If yes please take us
    throught the process of configuration.
    b) Is there is any patch available as a solution, give us the
    URL.
    c) To deploy forms 6.0 on web without changing what is the
    procedure ? Any know pitfalls ? Any design issues ?
    This is a strict timeline project, please give us a step by step
    solution if possible or point us in the right direction.
    Thanks in advance.
    null

    Gaurav Garg (guest) wrote:
    : Hi,
    : We have a client specified project requirement as follows.
    : 1. The platform
    : System need to work as atypical client server product with
    : forms running on all machine (Windows environement).
    : At the same time these forms should be deployable on the WEB
    : using Oracle Web Application Server.
    : 2. The versions
    : Oracle 8i 8.1.5
    : Oracle Developer 6.0
    : Oracle Web Application Server 4.0.7
    : 3. The problem
    : a) We installed 8i clients and developer 6.0 client on all
    : development machines. The Oracle 8i clients talk to the 8i
    : server but the forms 6.0 does not talk to 8i server. We get the
    : error message TNS service could not be resolved. I think this
    is
    : because developer does not expect to talk to 8i it expects to
    : talk to Oracle 8.0.5.
    I have oas 4.07, dev 6.0 and oracle 8i and oracle 8.0.x, and
    oracle 7.3.x running together. Your problem is most likely the
    TNSNAMES.ORA file, gather up all the tnsnames.ora, create one
    MASTER copy, and then
    regedit
    hkey_local_machine (dble click)
    software (dble click)
    oracle (single click) so that the right half of the screen is a
    list of keys, then right click on oracle, choose new-> string
    value
    enter the value: TNS_ADMIN
    then <cr> then right click on TNS_ADMIN choose modify, and enter
    the string:
    the PATH of your tnsnames.ora, format is:
    drive:\path
    e.g. for our installation with the file:
    w:\tns\tnsnames.ora
    available to everyone, just enter:
    w:\tns
    in the key value.
    This works EXCEPT for sqlplusw.exe the new client sqlplus that
    comes
    with 8i, this is fixed in 8.1.6 (don't ask oracle, they don't
    know when this is coming out) the workaround is to have an older
    version of plus, plus80w works fine to connect to all the
    databases.
    To check this, run an sqlplus session to each of your databases,
    if you can connect,then you should be able to connect using dev.
    6.0.
    Also, if you read the fine print in the release notes, oas 4.0.7
    will NOT work with multiple oracle homes on the NT. This should
    still be ok, as long as your 8i is remote,
    good luck, holler if you need any further help, and i can send
    you directory listings, and html that works.
    ps, watch out for the forms runform as web, it screws up images,
    but they are ok when run on the real webserver.
    : b) Same problem for the Application server, while
    configuration.
    : 4. (Stupid) Questions
    : a) Does Developer 6.0 work with 8i. If yes please take us
    : throught the process of configuration.
    : b) Is there is any patch available as a solution, give us the
    : URL.
    : c) To deploy forms 6.0 on web without changing what is the
    : procedure ? Any know pitfalls ? Any design issues ?
    : This is a strict timeline project, please give us a step by
    step
    : solution if possible or point us in the right direction.
    : Thanks in advance.
    null

  • Solution on drag & drop

    My query is?
    Please give a solution to whether drag & drop of components is possible in JApplet.
    Kindly send me the solution, if possible with a code example.
    Thanks.

    http://www.rockhoppertech.com/java-drag-and-drop-faq.html

  • The reporting point backflush is not possible for make-to-stock repetitive

    Hi All,
    we are using the assembly backflush in the MTS REM process. we are need to do the reporting point backflush
    if we tick against the RP backflush. what will be the effect in the process while confirmation.
    i read the sap library . it say like
    The reporting point backflush is not possible for make-to-stock repetitive manufacturing.
    is it correct.
    Thanks
    VRaj

    Hi mangal,
    i did all the setting as you said. but when click on the reporting point.
    system thru error
    Error reading reporting point information
    Message no. RM111
    Diagnosis
    The repetitive manufacturing profile is set for the reporting point procedure. However, either no reporting points exist for the material or they are incorrect. Two common reasons for this are:
    The repetitive manufacturing profile has been changed in the current session.
    You have not defined any milestone operations in the routing.
    When creating the product cost collector, no reporting points were created.
    Procedure
    Two alternative solutions are possible:
    Assign a repetitive manufacturing profile with no reporting point procedure to the material in the material master record.
    Recreate the reporting points by recosting the product cost collector. To do this, the following prerequisites must be met:
    In the material master record, in the production version, you must enter a routing under either detailed planning (first priority) or under rate-based planning (second priority).
    Milestone operations must exist in this routing. The system ususally automatically creates the reporting points from these milestones when creating a product cost collector or when creating a production version.
    how to create the REPORTING POINT

  • Heterogeneous query possible?

    I know this must get asked a lot, but I can't seem to get a good answer on a search.
    Situation: Table A resides on Oracle Server 1in Accounting, table B on Sybase Server 2.in Marketing (two different physical machines). Table A has a part number, Table B has its description.
    Question: Is there any way to return a single ResultSet (like "select A.partnum, B.desc from Accounting.Orders A, Marketing.Catalog B") from a single query, or must one query (A) be executed first, then a separate query on B executed for each row in ResultSet A?
    Wouldn't you need two connections and two data sources? Is there a way to do it if both servers are running Oracle?
    Any help greatly appreciated!
    Thanks,
    Reece Watkins

    Question: Is there any way to return a single
    ResultSet (like "select A.partnum, B.desc from
    Accounting.Orders A, Marketing.Catalog B") from a
    single query, or must one query (A) be executed first,
    then a separate query on B executed for each row in
    ResultSet A?HETERGENOUS DATABASE JOINS
    There are third party tools called Gateways that would allow this query across different vendor databases. This would allow you to execute a single query and return a single ResultSet. These third party tools are sometimes provided by the database vendors themselves (i.e. Oracle has a gateway for accessing mainframe DB2). I have not used these gateways with JDBC, but I cannot think of reason why they would not work with JDBC.
    Wouldn't you need two connections and two data
    sources? Is there a way to do it if both servers are
    running Oracle?USING ORACLE ONLY
    If you are running Oracle, you can setup an Oracle "link" between the two databases that allows you to code a single query that hits one or more Oracle databases to return a result set. You can do something similiar in most major databases.
    PROPRIETARY TEMP TABLE SOLUTION
    Another possible solution that avoids having to code your own mini-database engine, is to open up two connections, one to database A and one to database B. Then run query A against database A and store the ResultSet as a temporary table on database B. Now run your full query against database B against B's native tables and your temporary table. This avoids having to write functions to group, sort, avg, etc because you have the full power of database B at your disposal.
    In any case, using a third party Gateway, an Oracle link or some proprietary temp table solution, you will be eschewing performance for flexibility. That doesn't mean it is not a valid or good solution, only that scalability can be limited when runnning queries that span more than a single database regardless of the method.

  • Is it possible to sync aperture smart albums with an iphone?

    What I have on my Air is a smart album with all photos taken with my iphone(s). I want to sync this back to my iphone, but when I sync through itunes only ~1/2 the photos do in fact sync. Not immediately obvious which are and which are not. Most annoying.
    I am sure that I am not the first with this problem. Does anyone have a solution? Possibly the chap who advised me not to allow iphone library to grow into the 1000s! .
    Thanks for any assist.

    razmee209 wrote:
    No and it's consider illegal to do so.
    Only in some places.

  • Is it possible to Automate the Workbook using Reporting Agent??

    Hi Guru's,
    Can any one explain how to automate an Workbook that run weekly once?
    Please give me the steps or any document related to this.
    I have some Reporting Agent documents but i never worked on RA before.
    Please suggest me with best method and solution if possible.
    Will assign full points to the solution.
    Thanks in advance.
    BH
    Message was edited by:
            Varma Bh

    as of my understanding, you can't automate workbook. if you know the solution, please update.
    thanks,
    vsn

Maybe you are looking for

  • Difference in GL Balances between two Standard Report fbl3n and fagll03

    Hi , Mismatch of balances between two standard report ie.fbl3n and fagll03 . We are giving the complete example of what we are facing right now ... please go through the examples . ENTRY NO. 1 We have posted one MIRO , Accounting Posting is as below

  • An error occurred in the core cache

    Hi All <b>I have posted this Message almost 3 to 4 time , but no one has replied , as they have never come across the problem, if this is the case , we shud take those ases first. pls help !!!!</b> Case : ISA B2C CRM Deploying through SDM I have crea

  • I erased my MacBook pro and I set a code and I forgot it what could I do please help!

    I was just wondering to erase my MacBook off find my iPhone and I erased it and I put a code and now I don't remember it and I cant get in my MacBook can anyone help me plz!

  • Loading to essbase

    Hi All, Is there any possibility to do the dimension building and data loading at the same time using same source file. I am using essbase 6.5. and my data source would be excel sheets. If possible please suggest me how the source file should look li

  • IOS6 Devices Reject WiFi connections

    Ok so after loading iOS6, it looks like when you add a WiFi connection to your Iphone or Ipad, it verifies the WiFi connection with some page off the Apple.com website. When unable to do so it drops the WiFi connection you are trying to add. Example