EIGRP Metric and UCLB Doc
Team,
http://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/13677-19.html
I somehow find the doc for EIGRP unequal cost load balancing a little bit misleading because it shows that the cost to reach network X is additive to demonstrate EIGRP variance. The only time that the cost will be additive is if only delay is used along the path to network X. However, there is no mention about delay solely being used as the metric in the doc which might lead one to think that the metric for a certain route is FD = cost to neighbor + neighbor's RD.
Thoughts please. Thanks.
Team,
http://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/13677-19.html
I somehow find the doc for EIGRP unequal cost load balancing a little bit misleading because it shows that the cost to reach network X is additive to demonstrate EIGRP variance. The only time that the cost will be additive is if only delay is used along the path to network X. However, there is no mention about delay solely being used as the metric in the doc which might lead one to think that the metric for a certain route is FD = cost to neighbor + neighbor's RD.
Thoughts please. Thanks.
Similar Messages
-
12c - List of Metric and Polciy Settings.
I am doing research on 12c OEM, specifically what is monitored. What is the "Mertrics and Policy Settings" section in 12g.
http://docs.oracle.com/cd/E24628_01/doc.121/e24473/toc.htm is the main Cloud Admiins Guide but could not see what I am looking for in there.
Any links or tips would be welcome
Ta
MNHi,
I am not sure I understand exactly what you are looking for, but I will give a try. If you are looking for information on the "Metric and Policy Settings" page, it no longer exists in EM 12c.
Metric reference manuals are available here:
http://docs.oracle.com/cd/E24628_01/nav/reference.htm
In EM 12c, Compliance Standards replace metric policies. For information on Compliance see:
http://docs.oracle.com/cd/E24628_01/em.121/e27046/compliance_lcm.htm#CIAIICAF
Regards,
- Loc -
Hello everyone,
Many pages describing EIGRP say that one of used metrics is the interface MTU. However, the formula for calculating the composite metric does not take MTU into account so the MTU can not affect the composite metric of a route.
I would like to ask how exactly is the MTU used in the EIGRP, then. Thank your for any insights!
With best regards,
PeterPeter
You ask a very good question and I believe that you are on the right track in trying to understand it. Your observation is correct that MTU is a required parameter in specifying EIGRP metric (for redistribution) and is one of the parameters that is advertised. You are also correct in observing that there is nothing in the EIGRP calculation that uses MTU. So the real answer is that the EIGRP specification included MTU but that it does not play any active role in the path selection done by EIGRP.
HTH
Rick -
Billing Doc. and Accouting Doc
Hi ,
Is there any difference between Billing Doc. and Accouting Doc.?
Regards
AkashDear Akash,
In common terms:
Billing/ Invoice Document is a SD-Document, whereas
Accounting Document is FI-Document.
Billing document is created before the data transfer in the accounting.; whereas
An accounting document is a representation within the SAP System of the document (for example, an invoice) that triggered the posting.
When posting an accounting document, the SAP system updates the transaction figures in the accounts to which the document is posted.
Best regards,
Amit -
Number range of billing doc and accounting doc to be same
Hi Gurus,
Can any one help me out to make the number ranges of billing doc and accounting doc same every time.
Even though the invoice is cancelled the same no range should come for cancellation accounting doc.
Thanks in advance
DushyantHi,
Create or change the same interval for the BILLING DOCUMENTS & ACCOUNTING DOCUMENTS in VN01 and FBN1*
For BILLING DOCUMENTS assign this Number range in the VOFA transaction code for the Billing document tyes*
For ACCOUNTING DOCUMENTS assign this Number range in the FBN1 for your company code and fiscal year*
activate the External Field [] . this is mandtry
please check and revert back.
regards,
Anup Shukla -
How can I convert a pages color document to a PDF Black and White doc.
How can I convert a pages color document to a PDF Black and White doc. Or, covert the color to B&W in a new doc?
> How can I convert a pages color document to a PDF Black and White doc. Or, covert the color to B&W in a new doc?
The general idea is that you colour correct photographs once, archive, and convert with or without colour changes. The archived photograph is unchanged - or we would be colour correcting the same photographs again and again and again.
If you have a photograph with a corrected exposure, you can open the photograph in the Apple ColorSync Utility, apply a colour space conversion to a grayscale appearance using the preinstalled ICC profile, save the photograph under another name, and place that in your pagination.
If you have a paginated document with corrected exposures, and any such non-scalable bitmap or scalable spline graphics as you have chosen to add, you can render the pagination as a whole to PDF through the same ICC profile, carrying out the same colour space conversion on any and all objects.
Caveat: If you intend the pagination for certain processes, in particular offset lithography, then you are probably expected not to render the type to grayscale, but rather to render it to single ink solid black. No software can determine what printing process you intend, you have to understand a bit about printing, and how to set up general colour space conversions in software. Ask your prepress provider, and if the answer is not prompt and proficient, pick another provider.
/hh -
Hp officejet pro 8610 prints solid black on scanned pdf and word doc pictures
-HP Officejet Pro 8610
-problem printing scanned pdf document and word doc. photos
-My new HP Officejet Pro 8610 printed a newly scanned pdf document as an all black picture. I then printed a saved word documtent from my iMac which included a small picture. The document print was acceptable, but the picture was solid black. There were no error messages. These were, my initial tests, to check this new printer.Hey there @TM-10
Welcome to the Community
I read through your post about your new Officejet 8610 scanning a document to your computer and printing out all black. I have a couple ideas for you to try.
Try the steps in this guide: Unexpected Scan Output Using HP Scan Application for HP Multifunction Printers When Using OS X v10.9...
Press the Power button to turn on the product.
With the product turned on, disconnect the power cord from the rear of the product.
Unplug the power cord from the wall outlet.
Wait at least 15 seconds.
Plug the power cord back into the wall outlet.
Reconnect the power cord to the rear of the product.
If the product does not turn on by itself, press the Power button to turn it on.
Ensure the printer is plugged in directly to the wall outlet, avoiding power bars and surge protectors. This ensures the printer is receiving full power and may help.
Good luck
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution! -
I've ordered a new mac book pro 15" and i need to clean hard drive off my old PC...not really to move them to the mac, but just to save in case needed; mostly pics and office docs....any suggestions?
Buy an external USB hard drive and copy your data to it. Either that or burn them all to single or double layer DVDs (depending on amount of data you have). Or if it's really a small amount, consider putting it all on a USB memory stick.
-
How do I back up the contents of apps such as notes and office docs on my ipad to my PC ( windows op system) so I can use them on PC if my ipad fails?
You can use File Sharing in order to transfer the Word documents and the notes depending upon what apps you are using. Take a look at this.
iOS: About File Sharing - Support - Apple
There are file transfering apps like this one.
File Manager - Folder Plus on the App Store on iTunes
You can always email files as a last resort type of thing. That may not be practical depending upon the number of files that you have. -
Adobe Reader tries to open all files even Excel and Word docs.
When I try to open files that are sent to me, the Adobe Reader tries to open them all instead of an Excel file getting opened automatically by Excel and a .doc being opened by Word.
The message I get by the Reader says it cannot open it, of course. (I have Windows Vista on my HP computer if that is the problem.) Someone told me to take the default off of the Reader so the files open and download in the proper software program, but I am unable to find such a "default" option in the Reader program properties.
I never had this problem with any previous Windows version, so not sure if it is my computer, or the Reader. How can I fix this so when I download or open a file, it automatically opens in the right software?This means that the file associations of the various Office programs have been muddled up somehow. Try an Office repair install; that should correct the file associations.
-
Issue with HOST "metric and policy settings"
Hi All,
I have a OMS and EM Reporsitory installed on a linux machine I have connected four agents(4 hosts) to this grid control. For one perticular host I could not see any predefined metrics. The steps I followed are I have opened a host and went to "Metric and Policy Settings" and there I could not see any predefined metrics like Log file patteren match metrics and CPU utilization metric etc. For checking I have access "All Metrics" option there I can see all predefined metrics but their "collection Schedule" set to Real time-only. I think this is reason why I am not able to see these metrics in "Metric and Policy settings" for customization. How can change the Collection Schedule of these metric. This case is only for that perticular host other hosts are fine and showing metrics and allowing me to customize thresholds values.
As someone suggested I stopped and cleared the state of the agent and then started the agent again but the problem is not solved. Please suggest me a solution.
Regards,
Ashok ChavaYou could create a MONITORING TEMPLATE of the metrics you want to collect and base it off of a host that has the Metric and Policy Settings SET and apply it to this perticular host.
Have you checked Setup> Management Pack Access> for HOSTS? -
I am having problems interacting with Microsoft Office programs since the last update:cannot create a pdf through the 'print' menu in exel and both Word and Exel docs sent in Mac Mail end up being received as .dat files.
Both these situations have cropped up on my MacBook Pro since the last update.
Thanks for your help.
Cheers
BobThe 'Winmail.dat' problem has been extensively covered in these forums, I would search for that (a Google search works well) and unfortunately I have not seen the pdf print problem before, but assuming the software is current and functions normally (other than the pdf print problem) I have no suggestion other than the obvious (but time consuming) re-installation of Office.
I wish I had more -
Store and Display doc/pdf files in the database using Forms
Hi all,
How can i store and display doc/pdf files in the database using Forms 10g?.
ArifHow to get up and running with WebUtil 1.06 included with Oracle Developer Suite 10.1.2.0.2 on a win32 platform
Solution
Assuming a fresh "Complete" install of Oracle Developer Suite 10.1.2.0.2,
here are steps to get a small test form running, using WebUtil 1.06.
Note: [OraHome] is used as an alias for your real oDS ORACLE_HOME.
Feel free to copy this note to a text editor, and do a global find/replace on
[OraHome] with your actual value (no trailing slash). Then it is easy to
copy/paste actual commands to be executed from the note copy.
1) Download http://prdownloads.sourceforge.net/jacob-project/jacob_18.zip
and extract to a temporary staging area. Do not attempt to use 1.7 or 1.9.
2) Copy or move jacob.jar and jacob.dll
[JacobStage] is the folder where you extracted Jacob, and will end in ...\jacob_18
cd [JacobStage]
copy jacob.jar [OraHome]\forms\java\.
copy jacob.dll [OraHome]\forms\webutil\.
The Jacob staging area is no longer needed, and may be deleted.
3) Sign frmwebutil.jar and jacob.jar
Open a DOS command prompt.
Add [OraHome]\jdk\bin to the PATH:
set PATH=[OraHome]\jdk\bin;%PATH%
Sign the files, and check the output for success:
[OraHome]\forms\webutil\sign_webutil [OraHome]\forms\java\frmwebutil.jar
[OraHome]\forms\webutil\sign_webutil [OraHome]\forms\java\jacob.jar
4) If you already have a schema in your RDBMS which contains the WebUtil stored code,
you may skip this step. Otherwise,
Create a schema to hold the WebUtil stored code, and privileges needed to
connect and create a stored package. Schema name "WEBUTIL" is recommended
for no reason other than consistency over the user base.
Open [OraHome]\forms\create_webutil_db.sql in a text editor, and delete or comment
out the EXIT statement, to be able to see whether the objects were created witout
errors.
Start SQL*Plus as SYSTEM, and issue:
CREATE USER webutil IDENTIFIED BY [password]
DEFAULT TABLESPACE users
TEMPORARY TABLESPACE temp;
GRANT CONNECT, CREATE PROCEDURE, CREATE PUBLIC SYNONYM TO webutil;
CONNECT webutil/[password]@[connectstring]
@[OraHome]\forms\create_webutil_db.sql
-- Inspect SQL*Plus output for errors, and then
CREATE PUBLIC SYNONYM webutil_db FOR webutil.webutil_db;
Reconnect as SYSTEM, and issue:
grant execute on webutil_db to public;
5) Modify [OraHome]\forms\server\default.env, and append [OraHome]\jdk\jre\lib\rt.jar
to the CLASSPATH entry.
6) Start the OC4J instance
7) Start Forms Builder and connect to a schema in the RDBMS used in step (4).
Open webutil.pll, do a "Compile ALL" (shift-Control-K), and generate to PLX (Control-T).
It is important to generate the PLX, to avoid the FRM-40039 discussed in
Note 303682.1
If the PLX is not generated, the Webutil.pll library would have to be attached with
full path information to all forms wishing to use WebUtil. This is NOT recommended.
8) Create a new FMB.
Open webutil.olb, and Subclass (not Copy) the Webutil object to the form.
There is no need to Subclass the WebutilConfig object.
Attach the Webutil.pll Library, and remove the path.
Add an ON-LOGON trigger with the code
NULL;
to avoid having to connect to an RDBMS (optional).
Create a new button on a new canvas, with the code
show_webutil_information (TRUE);
in a WHEN-BUTTON-PRESSED trigger.
Compile the FMB to FMX, after doing a Compile-All (Shift-Control-K).
9) Under Edit->Preferences->Runtime in Forms Builder, click on "Reset to Default" if
the "Application Server URL" is empty.
Then append "?config=webutil" at the end, so you end up with a URL of the form
http://server:port/forms/frmservlet?config=webutil
10) Run your form.sarah -
I have a user using Acrobat 10. It was installed two weeks ago and initially had no problems. Today she reported that when she tries to convert multiple word and excel docs by selecting them, and right clicking on them to select convert/combine to PDF, random pages in the finished PDF have a blue background. I did some searching online and can find no information about this problem. Can anyone here shed some light on this issue and maybe point me in the direction of a solution? Any help is appreciated. Thanks!
Hi Gilad,
So, something I didn't consider was that this could be a setting in the office docs. The reason I didn't consider this was be cause we tested multiple docs and had similar results each time. I went back and looked into this possibility and found a setting in word that was causing this issue. Although the word doc showed no page color when opened in word, if I went to "Page Layout" -> "Page Color", a shade of blue was selected. By selecting "No Color", and then converting/combining the docs to PDF we got the desired result. Thanks again for your reply! -
Rebate: Differ "Scale Base Value" between "Statistics" and "Billing Doc"
Dear SD Expert,
After I go with Transaction Code :"VOB3" (run report RV15B002), I found that "Scale Base Value" have different value between "Statistics" and "Billing Doc". And the correct value is "Billing Doc". However, the value which shows in my rebate condition now is "Statistic". Thus, my question is
How can I configure my rebate condition based on "Billing Doc" Value instead of "Statistic"? (I don't want to "Correct backlogs" anytime in changing scales based value.) Anyone please feel free in suggestion.
Thanks,
PrachHI,
This may be useful to you.
http://help.sap.com/saphelp_47x200/helpdata/en/dd/5612d8545a11d1a7020000e829fd11/content.htm
Vrajesh
Maybe you are looking for
-
Email attachments sometimes disappear when sending to a PC user
When I send an email with an attachment (normally a PDF or JPG), in of course an exceptable size, to a PC user, the attachment will disappear for them. When they receive and open the email, only a small gray outlined box appears for them, with an "X"
-
Bug in Oracle XSchema Processor for Java v1 (recently released)
Running the sample file is giving the following error. Is this a bug Thanks Exception in thread "main" java.lang.NoSuchMethodError at oracle.xml.parser.schema.XSDBuilder.initParser(XSDBuilder.java:260) at oracle.xml.parser.schema.XSDBuilder.build(XSD
-
On Solaris 10 4Gb Ram, how much memory could be allocated to Oracle 11G instance? If I set memory_target=1200M the server starts okay and immediately. If I set memory_target=2500M the server takes very very long time to start - at some point over 45
-
AWR snapsohots not generating after restart of the instance
oracle : 10.2.0.3 OS : Linux 64-bit Issue : AWR snapshots are being generated after restart of the instance. I restarted the instance at 31.01.2010 8 AM CST. SQL> select STARTUP_TIME from v$instance; STARTUP_T 31-JAN-10 SQL> select max(begin_interva
-
Has any one out there encountered the ksbsrv error :- 'no startup aknowledgement from forked process after 3 mins' on a windows RAC configuration using 9.2.0.5? We have had this error on one of our 4 nodes. This rendered the entire database unusable