Ejecting problem on my 2nd SATA Hard Drive Bay Caddy

I am having an ejecting problem with my caddy secondary HD.
Basically every time I close the lid, the secondary HD is ejected or, in case ejecting fails, I obtain an error message..very annoying situation.
How can windows 7 avoid to eject it? Do you know a best practice to configure properly the 2nd SATA Hard Drive Bay Caddy??
Thanks in advance!
Fabio
Solved!
Go to Solution.

Really sorry, I didn't explain properly: I was talking about Ejecting OS side (windows 7 eject my secondary HD when I close my laptop, consequence is that I don't see it anymore in Computer).
ejecting is when you press here
anyway Thanks!!

Similar Messages

T430s 2nd Hard Drive Bay Caddy not working

Hi all,
I bought 2nd Hard Drive Bay Caddy for my T430s but it does not seem to work.
The HDDs I placed in it do not even start to spin, and they are not recognized by the laptop BIOS as also by my OSes, Windows and Linux.
The label on the caddy says it is P/N 26r9247, but at this stage I'm not sure is a compatible part or if I got just a faulty item.
Any feedback?
Solved!
Go to Solution.

That part number (26R9247) is for the older T60/61 Thinkpads. You need the Ultrabay III adapter. Look at 43N3412.

Hard Drive Bay (Caddy) and drive for T430

Very confused about what the recommended HDD Caddy for T430 is. (to swap DVD drive with a 2nd HDD)
Also, is there a non Lenovo HDD that works with this? 1 TB drive preferred.
Thanks.

Ultrabay caddies come in two thicknesses, 12.7mm for T430 and T530 (0A65623), and 9.5mm for T430s (43N3412.)
You can buy these from Lenovo or you can get "clone" caddies quite inexpensively on eBay, e.g. 9.5mm Bezel SATA 2nd HDD Hard Drive caddy bay for T400s T500 T410s X200 is $10 for a 9.5mm unit. This is what I have in my T430s. A 9.5mm caddie will fit into your T430 but will leave a small gap at the top. You can search to see what 12.7mm caddies are available.
I haven't tested the clone caddies with HDDs larger than 500GB. There's no reason they won't work. Note that the HDD must be no thicker than the caddy in order to fit physically. Since you have a T430 with 12.7 Ultrabay opening this shouldn't be an issue for you either.
Cheers... Dorian Hausman
X1C2, TPT2, T430s, SL500, X61s, T60p, A21p, 770, 760ED... 5160, 5150... S360/30

T430s 2nd Hard Drive Bay Caddy for windows 10? and main drive for win7

i am planning to run dual system: on the main drive, i am running windows 7 64bit pro which is my work PC. i dont want to risk the win 7 system.
i would like to run windwos 10 on the 2nd hard drive ( caddy). so i can choose which system to run each time when i power up my T430s. has any one done this yet? how is the result? can you choose which system to boot ?

Unfortunately for today 2015-08-17 windows 10 does NOT support hdd caddy

T43 2nd Hard Drive Bay Caddy not working

I installed a generic ultra bay caddy and the new drive isn't recognized.
It works fine in an external enclosure.
Any suggestions?

goretsky wrote:
Hello,
Do other Ultrabay caddies work in the T43 or does this one work in other ThinkPads?
Regards,
Aryeh Goretsky
The caddies for a T60/61 (also R and Z series) will work if you remove a plastic tab that prevents them from being inserted in a T4x or R5x series. The faceplate looks slightly different but it's not objectionable looking when installed.
ThinkPad W-510 i7-820QM(1.73-3.06GHz) Quad Core... ThinkPad T500, T9900, 8gb SSD...FrankNpad T-60p/61p (X9000 2.8ghz) 8gb SSD ips FlexView...ThinkPad T-61p (T9300 2.5ghz) 8gb ram...Thinkpad X-61 Tablet 4gb ram...ThinkPad A-31 (1.9ghz P4 1.5gb ram)

Installing a second SATA hard drive - Problems booting

Hi,
I currently have one Maxtor 160GB SATA hard drive in my system with my operating system installed. I have another identical hard drive that I'm attempting to install now, into the second of five available SATA ports on my MSI P965 Neo motherboard.
When I plug in the second hard drive, though, Windows will not boot. It gets to the Windows logo screen with the progress animation, but before even the animation can begin, it stops and the screen freezes. This does not fix itself with waiting.
My boot priorities are set to: DVD-ROM, CD-RW, hard risk. The hard disk priorities are also as they should be to my knowledge - although it can be tricky because when ordering, both disks have the same name. I have tried with either one on top of the list, and you cannot remove a drive from the list alltogether.
The SATA cable is in perfect condition. My BIOS is up-to-date.
When I plug the hard drive in when the system is already running, Windows will detect it and files can be written/read flawlessly. As soon as I restart, however, I run into the same issue.
The first HDD, with the OS on it, is in SATA 1, the second HDD is in SATA 4. Ports 3, 6, and 7 are unused.
I'm out of ideas at this point, I don't see any other options that need to be changed.
I'd appreciate any input you can offer - thanks in advance!

I would debug this drive you are talking about which clears off all data and partitions information. Take out the good drive and leave in the dodgy one. Boot to a floppy with this dell win95 boot disc.
http://support.dell.com/support/downloads/download.aspx?c=us&l=en&s=gen&releaseid=R19775&formatcnt=1&libid=0&fileid=19601
When at the A: prompt: type debug and enter, you get a (-) prompt and then enter the following script exactly:
F 200 L1000 0 (enter)
A CS:100 (enter)
xxxx:0100 MOV AX,301 (enter)
xxxx:0103 MOV BX,200 (enter)
xxxx:0106 MOV CX,1 (enter)
xxxx:0109 MOV DX,80 (enter)
xxx:010C INT 13 (enter)
xxxx:010E INT 20 (enter)
xxxx:0110 (enter)
g (enter)
q (enter)
restart your system.
Now you can put back in your first drive as well, boot up into windows and use the disc manager to repartition and format.
Old school! If you are still having problems I would replace the drive.

Sometimes cannot start PC: problem with Hitachi SATA Hard drive and K7N2G-ILSR

I have major problem with my 160Gb SATA Hitachi hard drive and my MSI K7N2G-ILSR motherboard. Sometimes the PC can be started, sometimes it cannot.
After I installed a clean build of Windows XP Pro SP1 onto my new hard drive (as the only hard drive in my PC) and install all the necessary drivers, the system runs smoothly. However, after about 2 to 3 weeks, sometimes when I start the PC, it cannot detect the hard drive and hence it claimes that it cannot find any VMI Pool Data (i.e. no OS detected). What makes it really horrible is that, it is like the lottery everytime when I start the PC. Sometimes it works, sometimes it doesn't. The highest record was 8 consecutive failures (by resetting or by turning the power off and on again) before I can start the machine properly. Also, the system sometimes just crashes in the middle of operating.
I have already sent the hard drive back to Hitachi. Got the same model of hard drive back as replacement, but the replacement has the same problem, except with the replacement drive the PC can be started eventually after many tries, while with the previous drive it is possible that the PC cannot be started until after a few days later.
Also, it seems that my drive can detect either SATA hard drive or PATA hard drive, but not both. (If I leave my old PATA drive connect in the primary IDE channel, Windows cannot detect the new SATA drive.)
Is my motherboard faulty? Can it only use PATA drive?
My PC's spec is as follows:
AMD Athlon XP 2500+
512Mb PC3200 SDRAM (set to run at 166MHz)
Hitachi 160Gb SATA Hard drive on 1st SATA channel (Model #HDS722516VLSA80)
Sony DVD+-RW drive and Panasonic DVD-ROM drive on secondary IDE channel
Use onboard video (GeForce MX)
US Robotech V92 internal PCI modem
SoundBlaster Audigy 2 Player soundcard
Onboard audio disabled
300W PSU
OS is Windows XP Pro SP1 (with all latest security patches up to date)

Quote
Originally posted by Raven_
Quote
Originally posted by boucher91
Along the same lines the sata drives use more power than the pata drives...
sata usually faster spin rate, pata is slower spin rate...
that is not entirly correct.
many harddrives just come with different ways to connect them.
the only sata drives i now that spins faster is western digital raptors 10k rpm.
all other is running at 7200rpm.
older drives run at 5400rpm
Yes to get the full benefit of RAID, the Raptors are the way to go.Anything else, no significant difference.

SATA hard drive problems with k8n neo4 plat

Helo , I am hoping someone can help me with this. I have read Fafner's thread on installing a sata hard drive on the neo4 mb but the only utility program I found on wd site is called " lifeguard11 for windows". Is this the right utility to use to partion my hard drive? I burned it to a cd and and my computer will post but will not boot from that cd. I have followed the instructions that came with the mb and used the floppys at F6 but it won't countinue to install windows after that.
Also I'm not sure how to enable sata in the bios. Do I go to integrated peripherals/sata devices config. and at the top of the screen it say's RAID Enable. Do I enable that and then enable sata1 raid? I am only using one hard drive. Thanks for help you can give.
k8n neo4 plat/bios v6.00 pg
amd 3800+
western digital 74GD Raptor
evga 6600gt
light-on cdr
floppy drive
ocz modstream 520 p/s
highspeedpc test bench

Quote from: roller on 27-March-06, 08:33:35
Helo , I am hoping someone can help me with this. I have read Fafner's thread on installing a sata hard drive on the neo4 mb but the only utility program I found on wd site is called " lifeguard11 for windows". Is this the right utility to use to partion my hard drive? I burned it to a cd and and my computer will post but will not boot from that cd. I have followed the instructions that came with the mb and used the floppys at F6 but it won't countinue to install windows after that.
Also I'm not sure how to enable sata in the bios. Do I go to integrated peripherals/sata devices config. and at the top of the screen it say's RAID Enable. Do I enable that and then enable sata1 raid? I am only using one hard drive. Thanks for help you can give.
k8n neo4 plat/bios v6.00 pg
amd 3800+
western digital 74GD Raptor
evga 6600gt
light-on cdr
floppy drive
ocz modstream 520 p/s
highspeedpc test bench
My system is similar to yours, if your just using the one Raptor you don't need any special drivers, your mother board will detect the Raptor with out any special settings. I hooked my Raptor up to SATA 1 (look on pg 2-2 of your book for the location) If your only planing on installing one operating system on your hard drive, such as windows XP pro, Windows will format and partition the drive for you.
If your having problems booting from a CD make sure you change the boot order in the BIOS (under advanced bios features pg. 3-8 of your manual) so that CD is before HD. For example, mine is set up for: First boot device = Floppy drive, Second boot device = CD Rom, Third boot device = hard drive, and etcetera. if your using more than one hard drive such as an IDE drive make sure you set the "hard disk boot priority" on the same page to the hard drive you want to boot from.
Once that is done put your Windows CD in the CD drive and reboot, Windows will guide you through the rest.

SATA Hard Drive no longer recognized by Mega 865

I recently put together an MSI Mega 865 barebone system with the following specifications:
Processor: Intel 3.2c Ghz (Northwood core)
Hard Drive: Western Digital SATA 10kRPM Raptor
Memory: 1 GB (2 x 512MB) Kingston 3200 (400Mhz)
DVD Player: Plextor 8X DVD RW
Video Card: HIS Excalibure 9800Pro 128 MB
OS: WinXP
Finally got everything up and running, and then I went to boot up, and the system can no longer find the SATA harddrive. In fact, it's not even an option in the BIOS now.
My question is the following:
Would the SATA be available all of the time, or only if a SATA enabled harddrive was recognized?
When the system is first powered on by plugging the power cord into the wall, the hard drive makes a small amount of noise, as if it's spinning a bit. When the computer starts up, there is no noise at all, although the hard drive does get warm (which makes me think there is power to the unit).
I tried the 2nd power supply (old IDE) for the hard drive, but that provided that same results as the SATA power supply.
There were some inconsistencies with my mega 865 prior to this. First, the HIFI would randomly lock up, and the only way to get it back was to unplug the computer from the wall. 2nd, it had lost communication on the serial port (why, I don't know). 3rd, and final, it doesn't seem to recognize my hard drive (or my hard drive is ruined).
Can someone help me out here, I'm not sure whether to return my HardDrive, my MSI Mega 865, or both.

The system worked for 4 days or so. One day, I started it up, and it couldn't boot because it couldn't detect the SATA drive. When this happened I decided to flash it to the the latest BIOS, but even this did not help.
The unit had problems before, it would lock up on initial power up, the HIFI/CD/DVD would not respond (when the computer was not on of course). I would have to plug and unplug the unit 3 or 4 times before it would power on and not lock up.
I contacted MSI support, and explained my problems. They told me to return the unit to the reseller. I'm not sure if the problem was the unit, the hard drive, or both, so I went ahead and returned the HD and the MSI unit. It'll be another 2 weeks or so now before I get my computer up and running. :(

Need help in installing a SATA hard drive with 865pe NEO2

Hello there
I need a help in installing a Sata hard drive ,it is WD 250 GB , my motherboard is 865PE Noe2 , the bios is the latest one
already I got another old hard drive ,not a Sata ,a regular IDE one installed as a master hard drive
I want to install the sata hd as a slave for the IDE hd for now to transfer the files and documents
I already physically installed the Sata hard drive yet the problem is that it was listed in the bios , I followed some of the steps here in the forum mentioned but all what I got is I found it listed as the fourth IDE master , not as the primary IDE slave
in Windows Xp Sp2 it is not listed of course in the windows explorer , but it is there in the device manager
look I am very confused and I tried most of the combinations in the ide configuration in BIOS
what should I do coz I am feeling so bad and stupid ,you can consider me a n00b in this hard drive thing

1st the sata drive cannot be listed as a slave drive to the ide master [key word=ide-can be configured as master OR slave, master IF only 1 hd, master and slave IF 2 hds], on the sata controler you can have master and slave, the ide cable has two connectors for the hds, sata has only 1 hd connector.
are you wanting to install the sata as primary master and move the operating sys to that drive, if so you will need an IMAGING software to move an operating system OR you could do a fresh operating system install to the sata drive then install your programs.

Seagate 300gig sata hard drive not recognized

I'm trying to install a seagate 300gb sata hard drive in my dual 2.0 g5.
I can plug in the two cables and the drive fits in fine, it even spins, however the computer does not recognize that the drive is there.
I've checked the sata in the system profile and tried disk utility but it is simply not there. Could this be a wiring problem or a bad drive? How do I check this?

My guess is that it is a Seagate 7200.9 with SSC on. If that is the case you will need a PC and this tool:
http://www.seagate.com/support/kb/disc/faq/ssc.html

MacBook hard drive and SATA hard drive

Can I use the Hitachi’s Travelstar 5K160 HTS541616J9SA00 2.5-inch SATA hard drive to, instead of putting their drive in the enclosure (it doesn’t come pre-installed), put my MAC Book (black model) hard drive in? I want to transfer the data from this hard drive into another MAC Book. My original computer had a problem with the board but I have my hard drive with data intact. I want to buy this SATA but am not sure if this would work, if I can put in the MacBook hard drive as if it was the SATA one... Help, anyone? Thanks!
MacBook Mac OS X (10.4.10)

Hi there,
A number of people on NewEgg's product page for that drive say it's great for a MacBook, so I'd assume it's ok.
You can put your old MacBook hard drive into any external USB2.0 enclosure and retrieve the data.
Regards!

Installing Windows XP on SATA Hard Drive

Hey. I have a maxtor 80gb SATA hard drive that I put in my new computer, and I want to install Windows XP on it. I see that the computer recognizes that it's there, but when I do the F6 process to get the drivers for Windows I cannot get anything for some reason. I hit F6, and it gets to the point where it asks me to install a disk with drivers, and I put the floppy for the VIA drivers in the drive (I'm using VIA after all I've read), and nothing happens. I don't even hear the floppy doing anything. after a few seconds of "please wait" the same screen comes up telling me to put the floppy containing the drivers in. Does anyone know what the problem could be? Also, in bios, it seems to recognize my floppy drive, since it lists it, and I can use it as a boot drive. If someone could help me out, I'd appreciate it. Thanks.

Hi
What is meant is the floppy is controlled from 2 parts of bios.
1. go to advanced bios features, set floppy seek to enable, set boot sequence to floppy, CD, HDD(BB1 = SATA), enable other devices. Then go to integrated peripherals, make sure PATA IDE and SATA IDE are enabled, just below is floppy controller, enable that, then SAVE and exit,
If the floppy cable was inverted, the drive light would be on all the time, if it flickers oon and off, it is OK.
Now try the F6 routine, if it still does not work then a new copy of floppy may be needed.
Cheers
jocko

Should I get a SATA hard drive?

I am about to mod my Xbox, and I am going to buy a new hard drive, but what I was thinking was that I could use my current 160 gig IDe drive and upgrade to a SATA drive.
Is there any problem with using just one SATA hard drive with my current setup?
I might not reply until this afternoon, I am at school.
Thanks

To answer your question: No there is no problem using a SATA drive with your setup. Indeed SATA is one of the features of this mobo so if you can use it. You don't list your PSU so I do not know whether your PSU has SATA power connectors, either way you should get a molex to sata convertor cable with your sata drive.

I want to change screenshot location from my Solid State hard drive with OSX on it, to my 2nd storage hard drive, how do I do this?

I want to change screenshot location from my Solid State hard drive with OSX on it, to my 2nd storage hard drive, how do I do this?
I am aware of "defaults write com.apple.screencapture *location*" but I want to change the location to my 2nd drive which doesn't have OSX on it... everytime I've tried to insert MacintoshHD2 in there it just doesn't work... any tips?

I'm having the same problem. I've entered the following path in terminal:
"defaults write.com.apple.screencapture location /Volumes/Macintosh HD 2/[my username]/Downloads"
But it's not working. It keeps going to the SSD Downloads folder.
What am I doing wrong?

Ejecting problem on my 2nd SATA Hard Drive Bay Caddy

Similar Messages

Maybe you are looking for