Elitebook 8460p error message

HP EliteBook 8460p
I got message right after power on.
Failed to get ME Kernel Host Interface version....
Removed HDD and reset BIOS doesn't help. Pass memory and HDD test in BIOS. Unable load from any external device.
I can't find any information about that problem. Please help.
Regards,
BBot

I found a reference to a reference to a possible problem here and I applied this patch but it didn't change a thing. 
The log, shown below, appears to have found my system all right "Found WIM. No need to do anything."
Still F11 not working 
Mounting HP_RECOVERY at C:\Users\JEANLU~1\AppData\Local\Temp\f11patchmount
Executing (\\KALGOORLIE\ROOT\CIMV2:Win32_Volume.DeviceID="\\​\\?\\Volume{df649fe3-ffc6-11e0-9cb8-402cf413e21d}\​\")->AddMountPoint()
Method execution successful.
Out Parameters:
instance of __PARAMETERS
ReturnValue = 0;
Getting architecture we are running under...
Running under 64-bit
Found WIM. No need to do anything.
Executing (\\KALGOORLIE\ROOT\CIMV2:Win32_Volume.DeviceID="\\​\\?\\Volume{df649fe3-ffc6-11e0-9cb8-402cf413e21d}\​\")->Dismount()
Method execution successful.
Out Parameters:
instance of __PARAMETERS
ReturnValue = 4;
Finished running the patch.

Similar Messages

  • Error message after changing 8460p motherboard

    I replaced a new motherboard on hp Elitebook 8460p with serial number - czc1293lxq Product - yq321ec#abb and when powered on it gives this error massage before booting to windows
    The following product information programmed into the system board is missing or invalid
    SYSTEM BOARD(OOA)-
    Product name
    Product Serial Number
    Product SKU
    ENTER- continue startup

    Hi:
    You have to take the PC to an authorized HP service center (or call HP technical support as to where to take it) and have the BIOS "tattooed" with all the missing info such as the serial number.
    There are no BIOS DMI tools available for customers to do this themselves.
    Paul

  • U310 Error Message on Boot Up

    I recently purchased an Ideapad U310. But after closing the laptop and opening it up I get an error message. I have tried to reset, boot into safemode, and pressed the Lenovo Recovery button on the side of the laptop, but the screen stays on the error message until I click ESC which leads me to boot order options, bios setup, and Diagnostic splash. These three options don't really lead me to anywhere with the error screen.
    The error message reads as follows:
    Recovery
    Your PC needs to be repaired
    The Boot Configuration Data File is missing some required information
    FIle:\BDCD
    Error code: 0xc000000d
    You'll need to use the recovery tools on your installation media. If you don't have any intallation 
    media (like a disc or USB device), contact your system administrator or PC manufacturer.
    Press ESC for UEFI Firmware settings
    Please help me solve this. Thank you!

    Firstly, to confirm, see if one key recovery works anymore. Follow the instruction in this kb
    http://forums.lenovo.com/t5/IdeaPad-Y-and-U-series-Laptops/How-to-do-System-Recovery-on-Lenovo-z580/...
    If you arent able to use one key recovery or you dont want to loose your c drive data, then you could use windows 7 repair console and use command prompt to rebuld a new bcd for booting.
    For creating bootable windows usb drive, use  Windows 7 USB/DVD Download tool. Install the program then choose the iso file of windows 7 downloaded officialy from here. After making a windows 7 usb, boot from it and follow the suggestions given in this link. However i suggest you use oneky recovery once.
    http://www.sevenforums.com/hardware-devices/82226-boot-bcd-0xc000000d-unreadable-boot-configuration-...
    Hope this helps
    Ishaan Ideapad Y560(i3 330m), Hp Elitebook 8460p!(i5-2520M) Hp Pavilion n208tx(i5-4200u)
    If you think a post helped you, then you can give Kudos to the post by pressing the Star on the left of the post. If you think a post solved your problem, then mark it as a solution so that others having the same problem can refer to it.

  • Error message when recovering

    Note: EliteBook 8460p
    OS: Original W7 Profesional
    Error message: Windows failed to start.
    I am trying to restore to factory settings my note but when pressing F11 when booting my machine it either goes to Windows or display the messages shown below, when choosing "Enter" it goes to another screen allowing me to boot Windows .
    The recovery partition is present on my machine

    I found a reference to a reference to a possible problem here and I applied this patch but it didn't change a thing. 
    The log, shown below, appears to have found my system all right "Found WIM. No need to do anything."
    Still F11 not working 
    Mounting HP_RECOVERY at C:\Users\JEANLU~1\AppData\Local\Temp\f11patchmount
    Executing (\\KALGOORLIE\ROOT\CIMV2:Win32_Volume.DeviceID="\\​\\?\\Volume{df649fe3-ffc6-11e0-9cb8-402cf413e21d}\​\")->AddMountPoint()
    Method execution successful.
    Out Parameters:
    instance of __PARAMETERS
    ReturnValue = 0;
    Getting architecture we are running under...
    Running under 64-bit
    Found WIM. No need to do anything.
    Executing (\\KALGOORLIE\ROOT\CIMV2:Win32_Volume.DeviceID="\\​\\?\\Volume{df649fe3-ffc6-11e0-9cb8-402cf413e21d}\​\")->Dismount()
    Method execution successful.
    Out Parameters:
    instance of __PARAMETERS
    ReturnValue = 4;
    Finished running the patch.

  • Elitebook 8460P - Shutdown and USB problem

    We're having a very odd problem.  When the system (HP Elitebook 8460P running Windows 7 x64 Enterprise) is online over wireless, everything works fine.  HOWEVER, 2 very odd behaviors manifest if the system is not connected to a wireless internet connection:
    - It will not shutdown.  The system will hang at "shutting down . . ." message. If the power is turned off (5 sec press on power button), it will boot up the next time saying that it was not shut down properly.
    - one of the USB 3 ports will not work (this is incredibly odd!).  Not sure how the 2 could be connected, but apparently they are!
    The system is well-maintained, and shows no signs of viruses or malware.  All drivers and software are up to date, including BIOS.  If the system is connected any working wireless connections, neither problem occurs.

    RNGhatesMe wrote:
    We're having a very odd problem.  When the system (HP Elitebook 8460P running Windows 7 x64 Enterprise) is online over wireless, everything works fine.  HOWEVER, 2 very odd behaviors manifest if the system is not connected to a wireless internet connection:
    - It will not shutdown.  The system will hang at "shutting down . . ." message. If the power is turned off (5 sec press on power button), it will boot up the next time saying that it was not shut down properly.
    - one of the USB 3 ports will not work (this is incredibly odd!).  Not sure how the 2 could be connected, but apparently they are!
    The system is well-maintained, and shows no signs of viruses or malware.  All drivers and software are up to date, including BIOS.  If the system is connected any working wireless connections, neither problem occurs.
    Hello!
    I suggest you open your command prompt and run the "sfc /scannow" command to ensure that your system files are intact.  Make sure to post the result.
    Have a great day.
    Please click the white star under my name to give me Kudos as a way to say "Thanks!"
    Click the "Accept as Solution" button if I resolve your issue.

  • Windows Vista: Ipod Error Message, no longer read by PCs

    Hello,
    I have a 5th generation black ipod video with 30GB of memory.
    The other day I hooked it up to my laptop (Toshiba, 4 months old) that it's been functioning on with no problems whatsoever. This weird error message flashed twice about it not being able to sync because of some software problem.
    Eversince then, the only thing I can charge my ipod on is the family treadmill in the basement (~_~) as no other computer in the house recognizes it. I can't even charge it through the wall sockets, either.
    I have changed the ipod cord, still no luck. I've also reset the device about 3 or 4 times and uninstalled, restarted the laptop then reinstalled itunes. I would like to reset it back to factory settings but that's impossible as computers/laptops don't pick it up. I live very far from a Mac store...
    What's a girl to do? I can't live without my Busta Rhymes and Wu-Tang Clan!
    Any advice would be greatly appreciated! Thanks!

    you have to update Vista go to this site and up-date http://windowsupdate.microsoft.com

  • Error message into a Variable.

    Dear users,
    I have a rather usual (unusual from the weekend beers for me though!!) query which I can't figure out a proper way to implement.
    My requirement is like this:
    I have a message class in which I want to define a text 'Employee number & not found'.
    I want to use this in the program, but not to raise this error. Instead, I want to move this error message with the Employee number into a Character(200) variable.
    So instead of using MESSAGE e0xx(messageclass) USING employee number, I would like to move the error text into a variable which looks like:
    lv_text = e0xx(messageclass) USING '1234'   which stores the text 'Employee number 1234 not found' in lv_text.
    How would I acheive it??
    Thanks, V!

    Try tis way
    message e999(00) with i_emp-empno into lv_text.
    press f1 in message will provide you more details
    a®

  • IPod seen by windows, not by iTunes+ weird error message

    I have a first generation 2GB iPod nano and i use windows xp. I can't load any music because iTunes doesn't see my iPod and an error message pops up that reads like this: "iTunes: iTunes.exe corrupt file. The file or directory \iPod_Control\iTunes is corrupt and unredable. Please run the checkdisk utility." I've tried everything, reinstalling iTunes, different versions, reinstalling OS, resetting iPod, even on another computer, same problem. Other than that, the iPod works normally, it's just lacking music..
    and why is there no email adress from apple for service qustions? 10x

    I still don't get it, how can I put it in disk mode if I CANNOT see the iPod in iTunes..?
    Did you read the document i linked you to? here's another link to it:
    Putting iPod into Disk Mode
    whereabouts in that procedure in that document (that you get to by clicking that link) does it say that you have to connect it to iTunes to put it into disk mode?
    ... never mind ... i guess you've fixed it anyway ...

  • Error message iPod cannot update b/c all of the playlists no longer exist

    Hello. I have been getting this error message. "Songs on the iPod "MAR(the name of my iPod)" cannot update because all of the playlists selecting for updating no longer exist." And my playlists are still on the left side in my iTunes. They do exist. I have a feeling ths might have to do with the fact that on vacation the person I was visiting gave me a gift of putting all of his music that would fit into the external hard drive part of my iPod, and for the past week or so I have been putting that music onto my 40 GB portable hard drive at home. I suspect I took a vital folder out of my iPod by accident. Right now I have the folder iPod_control if I open my iPod up in My Computer. Am I missing something? Right now my iPod is empty because iTunes made a composite playlist last week and I deleted it thinking I could get my real playlists back. Can you help me, or reccomend a site/someone who can? Thank you.
    PC   Windows XP  

    hiya!
    And my playlists are still on the left side in my iTunes. They do exist.
    let's just doublecheck this. folks get this message if they have "automatically update selected playlists only" selected in their itunes "ipod" preferences tab. so bring up that tab ("edit > preferences", click "ipod" while the ipod is showing up in the source list), and do a playlist by playlist crosscheck of the playlists selected in that tab, and the playlists showing up in the itunes sourcelist.
    is there any playlist selected in the preferences tab that isn't showing up in the sourcelist?
    love, b

  • Windows Blue Screen Error Message Appears As Soon As IPod Connected

    Everytime I connect my IPod to my computer, I get the Windows Blue Screen error message. Thought it was the cable, so plugged cable in by itself. No problem. Uninstalled IPod and ITunes software and then plugged in IPod, still got the Blue Screen. The Blue Screen says something about "recent plugged in device problem". It is not the cable, it must be the IPod. Did not have this problem when I bought it. Tried it on labtop and get the same error message. I can't do updater or anything that requires me to plug the IPod into a computer because the Blue Screen appears immediately. When I unplug, the Blue Screen remains and locks up the computer so I have to restart each time. I have tried everything I can think of. Please help.

    Hi Mike thank you for replying,
    I am not able to start the computer in safe mode, safe mode with networking, last good known configuration etc, Each time it quickly blue screens and restarts about two secs into the process.
    I was unable to try a clean OS install from the disk as it gave the blue screen error shown in the original post. The same thing happened when I tried to use the repair option on the XP home disc. So i can't get into the computer at all to start diagnosing the fault, the only clue I have is the error message, and after searching the internet I haven't found much enlightenment from that yet.
    If you can help me out or suggest where to search it would be much appreciated.
    Thx

  • IPod Error Message: "The disk could not be read from or written to."

    Hello!
    I was syncing my sister's video iPod (30GB) and this error message pops up "Attempting to copy to the disk. "SARAH'S IPO" failed. The disk could not be read from or written to."
    I have restored it three times already, but once it starts putting the music and files back onto the iPod it pops up with that error message. I have updated to the latest version of iTunes and iPod software available. My OS is Windows XP.
    Is this something serious? Will I be able to fix it myself or will I need to send it in to be fixed by Apple? Will that be expensive? We didn’t get the Apple replacement plan. D=
    Any help would be greatly appreciated. Thank you in advance. ^_^
    PowerBook G4   Mac OS X (10.4.3)   15" PowerBook 1.5 GHz PowerPC G4, 1.5GB RAM - Windows XP with iPod 5 Generation

    Okay I went thru that entire list and here's what I got...
    (1) My OS is XP and is running fine.
    (2) I've updated my windows
    (3) I don't know of any software that might be interfering.
    (4) There are no damaged files.
    (5) My Windows hard-drive is not damaged and I've tried restoring my iPod's disk thru iTunes but it still doesn't work.
    (6) I don't have an iPod photo and I can't find the folder to delete the cache if if I did.
    (7) The USB cord is firmly connected into my USB port and my iPod
    (8) My music is on my external hard-drive so I need to keep 3rd-party hardware connected
    (9) I will try another USB cord to see if that works.
    Is there anything else that I can do? Can Apple fix this?
    Please let me know.

  • IPod Touch will no longer sync...error message.

    For some reason my older iPod Touch without a camera on it will not sync any more and I am getting an error message saying this iPod cannot be synced. Now I had it set up to sync over Wi-Fi and I would occasionally hook up to the computer with the cable and got error messages on both. Now I read something about removing the SC Info Folder. If I do that will that mess things up with syncing my iPhone? 

    What is the exact wording of the error message?

  • Error Message: Need to purge Cache in Adobe Bridge CC (on PC)

    I tried purging using Adobe Bridge by going to Edit/Preferences/Cache then purging, but it becomes non responsive.  The error message said the problem files were at Users/(my user name)/AppData/Roaming/Adobe/BridgeCC/Cache.   There are 4 files in there that are taking up 124 GB!  Can I simply delete these files or will it corrupt my regular files?  I tried doing as some other forums suggested and hold the ALT key down when opening Bridge before purging, but no luck.

    Yes, you can delete the cache files manually,  Just be advised that Bridge will become very, very slow until it finishes rebuilding its caches.  Depending on your files, that can take a few minutes or several hours.
    A good way of doing it is at night, so you can do it before going to bed and let Bridge rebuild caches overnight.
    If you can, save the cache files before deleting them to an external drive, so that you'll have them as backup if something goes wrong.

  • Error message when installing Photoshop CS2 in Windows 8

    I just upgraded to a computer with Windows 8.  I use Photoshop CS2.  I am getting the error message below when starting photoshop after installation.  I changed program folders, but that did not work.  Please advise. 
    Error: an error has been detected and activation cannot continue. Please restart your computer and reinstall application.

    http://helpx.adobe.com/x-productkb/policy-pricing/creative-suite-2-activation-end-life.htm l

  • Adobe Photoshop CS2 Error messages after update to mac os 10.4.6

    After updated to mac os 10.4.6 everytime I use Photoshop CS2 I receive an error message "Could not complete your request because of a program error"
    I did all the workarounds that were described in document 331627 from Adobe's website and nothing worked.
    I also subscribe to maxosx.com support and someone suggested removing the legal.localized/Tien...file from the photoshop cs2/legal directory, but everytime I tried to select the directory "legal" from within the finder view, it disappeared and closed the finder window.
    HELP!

    Did you upgrade from a previous version of OS X like 10.3.x or 10.2.x or from a prior version of 10.4.x? If the former, there are probably some files in your previous system folder that need to be restored.
    Otherwise, double click Photoshop when it's closed, and then IMMEDIATELY hold Command + Option + Shift. You'll get a box for resetting the settings. Select Yes and maybe that will help.
    --Ryan

Maybe you are looking for