Ellipsis 7 not working

My ellipsis 7 will not go to any app that I have on my tablet plus it turns off within 5 seconds off use.while trying to get to an app. Screen freezes on me and restarts it self. Then when I try and turn off the device it will not turn off.

Oh my, mrvlyn. That's certainly strange behavior for your tablet. When it freezes or restarts, do you see any error message? Please go into Settings > About Tablet > SW Version and let us know what software version you see. Also, please go into Settings > Apps > Downloaded, then begin selecting one application at a time > select 'Move to tablet space', if it is available.
JenniferH_VZW
Follow us on Twitter www.twitter.com/vzwsupport

Similar Messages

Ellipsis 7 not working after 3 months

I purchased an Elipsis 7 for my husband to use while he is out in the field to do minor things such as check and respond to emails. Last week it simply quit working, He took it in to the Verizon store and had a sales rep look at it and sure enough, it would not turn on. The gentleman in the store explained we would have to call the tech line and have it replaced as it would still fall under the one year manufacturer warranty. No problem, I understand there are channels to be followed. I called Friday 10/17 and spoke to a representative that informed me he was placing an order for a replacement device, (after we went through the same steps all over again to ensure the device was indeed not working.) I even have my confirmation e-mail stating a replacement device is being sent and how to return the defective device. The associate went over with me the fact that if there is any water or other damage we would be charged the $300 for the device. Again, fine, I know there is a process. He also stated we would receive the replacement device yesterday 10/20. I did not receive it so I called back today as there was no tracking information available on my account. The gentleman I spoke with this evening stated the order has not shipped yet and he cannot tell why and that he would have to cancel the original request and submit a new one. The main problem with this is he is stating they are having to send a recovery box, clearly different than the discussion I had with the rep on Friday. So now, not only was our order delayed, but we will not even be getting the replacement until after they review the original device so we're looking at a minimum of another week. For an item that is only 3 months old that has been well taken care of this is a ridiculous amount of hassle. I have been on the phone now for a total of 2 hrs and still have a tablet that is not working. I am extremely dissatisfied with the lack of knowledge and consistency from one employee to another. They couldn't have been any more friendly, they are just kindly misinforming your customers. If this is how you all handle your claims on a new device, I will not be renewing my contract and will even consider going to one of your competitors that buys out your contracts. This is the first claim I have ever had to file after a decade of patronage and I could not be any unhappier.

Hi kld01
Thank you for your feedback. We were sorry to hear about your experience and have already made changes to internal resources about the Ellipsis 7 to hopefully provide more consistent communications about the recovery box process. Your tablet will be fixed through recovery box as this is the only repair process for the Ellipsis 7. Following is what you can expect as far as timing:
- Your recovery box should arrive within 3 days
- The box should arrive to the manufacturer within 2-3 days after you ship it
- The manufacturer will repair the Ellipsis 7 and ship it back to you within 3 days
- You should receive your device within 2 days

Illustrator - Ellipse tool not working properly

Hi,
totally new to Illustrator, so probably a silly question, but I really don't know what to do at this point.
Suddenly when using the ellipse, rectangle,...tool, when drawing the object, it shows the path (pls see picture below). I obviously clicked something/turned on some functionality that I shouldn't have, but I have no idea which and how.
Any help would be greatly appreciated :-)
Thanks.

Thanks so much! I would have never thought of that.

Shift key and ellipse tool not working

Can't make a perfect circle in CS5 using shift key. Anyone else having this problem?

Order,
If the Type remains unchanged when selected, you seem to need to both Show Edges and Show Bounding Box under View. You should be able to move it though. Otherwise, something else is wrong.

Rectangle menu not working

Hi! I am trying to draw a circle and I can't bring in the ellipse tool because for some reason the menu that is suppose to come up when you click and hold the rectangle tool is not working. What can I do to fix it?

Unfortunately you do not say which version of spry you are using, so first make sure that you have the current version as this fixes many of the IE related problems.
You can get the latest version by visiting:http://www.labs.adobe.com/technologies/spry/
HTH
PZ

I am trying to hide the Options menu in UserChrome.css but it is not working. Here is what I have tried menuitem[label="Options..."] {display:none !important;}

In the userChrome.css I have tried the following entry: #updateSeparator, #checkForUpdates {display: none !important;}
menuitem[label="Options..."] {display:none !important;}
menuitem[label="Add-ons"] {display:none !important;}
menuitem[label="Get Bookmark Add-ons"] {display:none !important;}
The other lines work, but the line to hide the Options menu does not. This in on Windows 32-bit XP sp3.

It is an ellipsis (…) and not three dots.
If there is an ID for a menu entry like in this case #menu_preferences then it is better to use that ID.
<pre><nowiki>#menu_preferences, #menu_openAddons, {display:none!important;}</nowiki></pre>
"Get Bookmark Add-ons" is a normal bookmark that you can remove via the right-click context menu or move elsewhere.

Why is Rectangle Tool's matching dimension feature not working?

With the Rectangle Tool's cursor is clicked in the document.
The Rectangle Panel appears.
A height dimension is entered.
With the pointer, the Width field is clicked.
Usually, the Height Value gets automatically entered in the Width field.
In this case it does not.
This same behavior is occuring in the Ellipse Tool.
What has changed?
Thanks
iMac 3.4Ghz 32 GB
OSX 10.8.2
Illustrator CS6

I may not have been clear on what is not working... the feature I am trying to create has been in Illustrator for several versions... another discusion on this site deals with the same problem...
see http://forums.adobe.com/message/4910715... it is explained...
'There has always been a one click solution, just like the help file says. Try it in CS5, click once with the tool, enter your width value, click on the word height, ill copies the width value into the height field, hit enter and you are done.'
it is this function that I have used for years.

Bumblebee not working

Pages read:
https://wiki.archlinux.org/index.php/Bu … l.2FNVIDIA
https://bbs.archlinux.org/viewtopic.php … 9#p1178729
https://bbs.archlinux.org/viewtopic.php?id=159666
And many other threads too old and different to be useful.
My system:
$ uname -a
Linux biscottyno 3.15.7-1-ARCH #1 SMP PREEMPT Mon Jul 28 20:06:17 CEST 2014 x86_64 GNU/Linux
$ lspci | grep -i nvidia
01:00.0 3D controller: NVIDIA Corporation GM107M [GeForce GTX 860M] (rev a2)
$ pacman -Q linux intel-dri xf86-video-intel bumblebee nvidia lib32-nvidia-utils lib32-intel-dri bbswitch
linux 3.16.1-1
intel-dri 10.2.6-1
xf86-video-intel 2.99.914-4
bumblebee 3.2.1-3
nvidia 340.32-1
lib32-nvidia-utils 340.32-1
lib32-intel-dri 10.2.6-1
bbswitch 0.8-15
Kernel version is not matching in uname and pacman, as well in:
$ ls -a /lib/modules
. 3.15.7-1-ARCH extramodules-3.15-ARCH
.. 3.16.1-1-ARCH extramodules-3.16-ARCH
I think I have to update GRUB from the debian partition. I'll check now.
I installed bumblebee with:
sudo pacman -S intel-dri xf86-video-intel bumblebee nvidia lib32-nvidia-utils lib32-intel-dri
Anyway wiki doesn't suggest to install bbswitch, which I think is essential, so I've installed it as well.
I've configured bumblebee:
$ cat /etc/bumblebee/bumblebee.conf
# Configuration file for Bumblebee. Values should **not** be put between quotes
## Server options. Any change made in this section will need a server restart
# to take effect.
[bumblebeed]
# The secondary Xorg server DISPLAY number
VirtualDisplay=:8
# Should the unused Xorg server be kept running? Set this to true if waiting
# for X to be ready is too long and don't need power management at all.
KeepUnusedXServer=false
# The name of the Bumbleblee server group name (GID name)
ServerGroup=bumblebee
# Card power state at exit. Set to false if the card shoud be ON when Bumblebee
# server exits.
TurnCardOffAtExit=false
# The default behavior of '-f' option on optirun. If set to "true", '-f' will
# be ignored.
NoEcoModeOverride=false
# The Driver used by Bumblebee server. If this value is not set (or empty),
# auto-detection is performed. The available drivers are nvidia and nouveau
# (See also the driver-specific sections below)
Driver=nvidia
# Directory with a dummy config file to pass as a -configdir to secondary X
XorgConfDir=/etc/bumblebee/xorg.conf.d
## Client options. Will take effect on the next optirun executed.
[optirun]
# Acceleration/ rendering bridge, possible values are auto, virtualgl and
# primus.
Bridge=auto
# The method used for VirtualGL to transport frames between X servers.
# Possible values are proxy, jpeg, rgb, xv and yuv.
VGLTransport=proxy
# List of paths which are searched for the primus libGL.so.1 when using
# the primus bridge
PrimusLibraryPath=/usr/lib/primus:/usr/lib32/primus
# Should the program run under optirun even if Bumblebee server or nvidia card
# is not available?
AllowFallbackToIGC=false
# Driver-specific settings are grouped under [driver-NAME]. The sections are
# parsed if the Driver setting in [bumblebeed] is set to NAME (or if auto-
# detection resolves to NAME).
# PMMethod: method to use for saving power by disabling the nvidia card, valid
# values are: auto - automatically detect which PM method to use
# bbswitch - new in BB 3, recommended if available
# switcheroo - vga_switcheroo method, use at your own risk
# none - disable PM completely
# https://github.com/Bumblebee-Project/Bumblebee/wiki/Comparison-of-PM-methods
## Section with nvidia driver specific options, only parsed if Driver=nvidia
[driver-nvidia]
# Module name to load, defaults to Driver if empty or unset
KernelDriver=nvidia
PMMethod=bbswitch
# colon-separated path to the nvidia libraries
LibraryPath=/usr/lib/nvidia:/usr/lib32/nvidia
# comma-separated path of the directory containing nvidia_drv.so and the
# default Xorg modules path
XorgModulePath=/usr/lib/nvidia/xorg/,/usr/lib/xorg/modules
XorgConfFile=/etc/bumblebee/xorg.conf.nvidia
## Section with nouveau driver specific options, only parsed if Driver=nouveau
#[driver-nouveau]
#KernelDriver=nouveau
#PMMethod=auto
#XorgConfFile=/etc/bumblebee/xorg.conf.nouveau
I've commented out every line in /etc/X11/xorg.conf.d/30-intel.conf (the nVIDIA line were an experiment):
$ cat /etc/X11/xorg.conf.d/30-intel.conf
# Posizione originale /etc/X11/xorg.conf.d/30-intel.conf
#Section "Device"
# Identifier "Intel Graphics"
# Driver "intel"
# Option "TearFree" "true"
#EndSection
#Section "Device"
# Identifier "nvidiagpu1"
# Driver "nvidia"
# BusID "PCI:01:00.0"
#EndSection
Configuration done, now I try bumblebee with glxgears:
$ optirun glxgears
[ 290.027113] [ERROR]The Bumblebee daemon has not been started yet or the socket path /var/run/bumblebee.socket was incorrect.
[ 290.027133] [ERROR]Could not connect to bumblebee daemon - is it running?
Checking bumblebeed:
$ systemctl status bumblebeed
● bumblebeed.service - Bumblebee C Daemon
Loaded: loaded (/usr/lib/systemd/system/bumblebeed.service; enabled)
Active: activating (auto-restart) (Result: exit-code) since sab 2014-08-30 17:56:02 CEST; 45s ago
Process: 806 ExecStart=/usr/bin/bumblebeed (code=exited, status=1/FAILURE)
Main PID: 806 (code=exited, status=1/FAILURE)
ago 30 17:56:02 biscottyno systemd[1]: Unit bumblebeed.service entered fail...e.
Hint: Some lines were ellipsized, use -l to show in full.
Reading 'journalctl -b':
Here is when Bumblebee is started.
ago 30 17:55:02 biscottyno systemd[1]: Starting Initialize hardware monitoring sensors...
ago 30 17:55:02 biscottyno systemd[1]: Starting dhcpcd on all interfaces...
ago 30 17:55:02 biscottyno systemd[1]: Starting Login Service...
ago 30 17:55:02 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 17:55:02 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 17:55:02 biscottyno systemd[1]: Starting D-Bus System Message Bus...
ago 30 17:55:02 biscottyno systemd[1]: Started D-Bus System Message Bus.
Here are the failed attempts.
ago 30 17:55:02 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 17:55:02 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
ago 30 17:55:02 biscottyno systemd[1]: Started Initialize hardware monitoring sensors.
ago 30 17:55:02 biscottyno systemd[1]: Starting Authorization Manager...
ago 30 17:55:02 biscottyno bumblebeed[321]: modprobe: FATAL: Module bbswitch not found.
ago 30 17:56:02 biscottyno systemd[1]: bumblebeed.service holdoff time over, scheduling restart.
ago 30 17:56:02 biscottyno systemd[1]: Stopping Bumblebee C Daemon...
ago 30 17:56:02 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 17:56:02 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 17:56:02 biscottyno bumblebeed[806]: modprobe: FATAL: Module bbswitch not found.
ago 30 17:56:02 biscottyno bumblebeed[806]: [ 63.553397] [ERROR]Module bbswitch could not be loaded (timeout?)
ago 30 17:56:02 biscottyno bumblebeed[806]: [ 63.553410] [WARN]No switching method available. The dedicated card will always be on.
ago 30 17:56:02 biscottyno bumblebeed[806]: [ 63.554074] [ERROR]Module 'nvidia' is not found.
ago 30 17:56:02 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 17:56:02 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
ago 30 17:57:02 biscottyno systemd[1]: bumblebeed.service holdoff time over, scheduling restart.
ago 30 17:57:02 biscottyno systemd[1]: Stopping Bumblebee C Daemon...
ago 30 17:57:02 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 17:57:02 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 17:57:02 biscottyno bumblebeed[846]: modprobe: FATAL: Module bbswitch not found.
ago 30 17:57:02 biscottyno bumblebeed[846]: [ 123.584265] [ERROR]Module bbswitch could not be loaded (timeout?)
ago 30 17:57:02 biscottyno bumblebeed[846]: [ 123.584277] [WARN]No switching method available. The dedicated card will always be on.
ago 30 17:57:02 biscottyno bumblebeed[846]: [ 123.584973] [ERROR]Module 'nvidia' is not found.
ago 30 17:57:02 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 17:57:02 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
ago 30 17:58:02 biscottyno systemd[1]: bumblebeed.service holdoff time over, scheduling restart.
ago 30 17:58:02 biscottyno systemd[1]: Stopping Bumblebee C Daemon...
ago 30 17:58:02 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 17:58:02 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 17:58:02 biscottyno bumblebeed[872]: modprobe: FATAL: Module bbswitch not found.
ago 30 17:58:02 biscottyno bumblebeed[872]: [ 183.834661] [ERROR]Module bbswitch could not be loaded (timeout?)
ago 30 17:58:02 biscottyno bumblebeed[872]: [ 183.834674] [WARN]No switching method available. The dedicated card will always be on.
ago 30 17:58:02 biscottyno bumblebeed[872]: [ 183.835367] [ERROR]Module 'nvidia' is not found.
ago 30 17:58:02 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 17:58:02 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
ago 30 17:59:03 biscottyno systemd[1]: bumblebeed.service holdoff time over, scheduling restart.
ago 30 17:59:03 biscottyno systemd[1]: Stopping Bumblebee C Daemon...
ago 30 17:59:03 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 17:59:03 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 17:59:03 biscottyno bumblebeed[889]: modprobe: FATAL: Module bbswitch not found.
ago 30 17:59:03 biscottyno bumblebeed[889]: [ 244.084319] [ERROR]Module bbswitch could not be loaded (timeout?)
ago 30 17:59:03 biscottyno bumblebeed[889]: [ 244.084328] [WARN]No switching method available. The dedicated card will always be on.
ago 30 17:59:03 biscottyno bumblebeed[889]: [ 244.085023] [ERROR]Module 'nvidia' is not found.
ago 30 17:59:03 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 17:59:03 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
ago 30 18:00:03 biscottyno systemd[1]: bumblebeed.service holdoff time over, scheduling restart.
ago 30 18:00:03 biscottyno systemd[1]: Stopping Bumblebee C Daemon...
ago 30 18:00:03 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 18:00:03 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 18:00:03 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 18:00:03 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
ago 30 18:00:03 biscottyno bumblebeed[898]: modprobe: FATAL: Module bbswitch not found.
ago 30 18:00:03 biscottyno bumblebeed[898]: [ 304.334392] [ERROR]Module bbswitch could not be loaded (timeout?)
ago 30 18:00:03 biscottyno bumblebeed[898]: [ 304.334401] [WARN]No switching method available. The dedicated card will always be on.
ago 30 18:00:03 biscottyno bumblebeed[898]: [ 304.335053] [ERROR]Module 'nvidia' is not found.
ago 30 18:01:03 biscottyno systemd[1]: bumblebeed.service holdoff time over, scheduling restart.
ago 30 18:01:03 biscottyno systemd[1]: Stopping Bumblebee C Daemon...
ago 30 18:01:03 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 18:01:03 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 18:01:03 biscottyno bumblebeed[905]: modprobe: FATAL: Module bbswitch not found.
ago 30 18:01:03 biscottyno bumblebeed[905]: [ 364.584501] [ERROR]Module bbswitch could not be loaded (timeout?)
ago 30 18:01:03 biscottyno bumblebeed[905]: [ 364.584512] [WARN]No switching method available. The dedicated card will always be on.
ago 30 18:01:03 biscottyno bumblebeed[905]: [ 364.585195] [ERROR]Module 'nvidia' is not found.
ago 30 18:01:03 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 18:01:03 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
ago 30 18:02:03 biscottyno systemd[1]: bumblebeed.service holdoff time over, scheduling restart.
ago 30 18:02:03 biscottyno systemd[1]: Stopping Bumblebee C Daemon...
ago 30 18:02:03 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 18:02:03 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 18:02:03 biscottyno bumblebeed[914]: modprobe: FATAL: Module bbswitch not found.
ago 30 18:02:03 biscottyno bumblebeed[914]: [ 424.834589] [ERROR]Module bbswitch could not be loaded (timeout?)
ago 30 18:02:03 biscottyno bumblebeed[914]: [ 424.834601] [WARN]No switching method available. The dedicated card will always be on.
ago 30 18:02:03 biscottyno bumblebeed[914]: [ 424.835288] [ERROR]Module 'nvidia' is not found.
ago 30 18:02:03 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 18:02:03 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
ago 30 18:03:04 biscottyno systemd[1]: bumblebeed.service holdoff time over, scheduling restart.
ago 30 18:03:04 biscottyno systemd[1]: Stopping Bumblebee C Daemon...
ago 30 18:03:04 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 18:03:04 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 18:03:04 biscottyno bumblebeed[919]: modprobe: FATAL: Module bbswitch not found.
ago 30 18:03:04 biscottyno bumblebeed[919]: [ 485.084540] [ERROR]Module bbswitch could not be loaded (timeout?)
ago 30 18:03:04 biscottyno bumblebeed[919]: [ 485.084551] [WARN]No switching method available. The dedicated card will always be on.
ago 30 18:03:04 biscottyno bumblebeed[919]: [ 485.085236] [ERROR]Module 'nvidia' is not found.
ago 30 18:03:04 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 18:03:04 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
ago 30 18:03:04 biscottyno systemd-logind[319]: Lid closed.
ago 30 18:04:04 biscottyno systemd[1]: bumblebeed.service holdoff time over, scheduling restart.
ago 30 18:04:04 biscottyno systemd[1]: Stopping Bumblebee C Daemon...
ago 30 18:04:04 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 18:04:04 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 18:04:04 biscottyno bumblebeed[927]: modprobe: FATAL: Module bbswitch not found.
ago 30 18:04:04 biscottyno bumblebeed[927]: [ 545.334610] [ERROR]Module bbswitch could not be loaded (timeout?)
ago 30 18:04:04 biscottyno bumblebeed[927]: [ 545.334622] [WARN]No switching method available. The dedicated card will always be on.
ago 30 18:04:04 biscottyno bumblebeed[927]: [ 545.335338] [ERROR]Module 'nvidia' is not found.
ago 30 18:04:04 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 18:04:04 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
ago 30 18:04:17 biscottyno systemd-logind[319]: Lid opened.
ago 30 18:05:04 biscottyno systemd[1]: bumblebeed.service holdoff time over, scheduling restart.
ago 30 18:05:04 biscottyno systemd[1]: Stopping Bumblebee C Daemon...
ago 30 18:05:04 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 18:05:04 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 18:05:04 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 18:05:04 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
ago 30 18:05:04 biscottyno bumblebeed[933]: modprobe: FATAL: Module bbswitch not found.
ago 30 18:05:04 biscottyno bumblebeed[933]: [ 605.584505] [ERROR]Module bbswitch could not be loaded (timeout?)
ago 30 18:05:04 biscottyno bumblebeed[933]: [ 605.584514] [WARN]No switching method available. The dedicated card will always be on.
ago 30 18:05:04 biscottyno bumblebeed[933]: [ 605.585190] [ERROR]Module 'nvidia' is not found.
ago 30 18:06:04 biscottyno systemd[1]: bumblebeed.service holdoff time over, scheduling restart.
ago 30 18:06:04 biscottyno systemd[1]: Stopping Bumblebee C Daemon...
ago 30 18:06:04 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 18:06:04 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 18:06:04 biscottyno bumblebeed[940]: modprobe: FATAL: Module bbswitch not found.
ago 30 18:06:04 biscottyno bumblebeed[940]: [ 665.835175] [ERROR]Module bbswitch could not be loaded (timeout?)
ago 30 18:06:04 biscottyno bumblebeed[940]: [ 665.835194] [WARN]No switching method available. The dedicated card will always be on.
ago 30 18:06:04 biscottyno bumblebeed[940]: [ 665.836211] [ERROR]Module 'nvidia' is not found.
ago 30 18:06:04 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 18:06:04 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
ago 30 18:07:05 biscottyno systemd[1]: bumblebeed.service holdoff time over, scheduling restart.
ago 30 18:07:05 biscottyno systemd[1]: Stopping Bumblebee C Daemon...
ago 30 18:07:05 biscottyno systemd[1]: Starting Bumblebee C Daemon...
ago 30 18:07:05 biscottyno systemd[1]: Started Bumblebee C Daemon.
ago 30 18:07:05 biscottyno bumblebeed[947]: modprobe: FATAL: Module bbswitch not found.
ago 30 18:07:05 biscottyno bumblebeed[947]: [ 726.084610] [ERROR]Module bbswitch could not be loaded (timeout?)
ago 30 18:07:05 biscottyno bumblebeed[947]: [ 726.084623] [WARN]No switching method available. The dedicated card will always be on.
ago 30 18:07:05 biscottyno bumblebeed[947]: [ 726.085313] [ERROR]Module 'nvidia' is not found.
ago 30 18:07:05 biscottyno systemd[1]: bumblebeed.service: main process exited, code=exited, status=1/FAILURE
ago 30 18:07:05 biscottyno systemd[1]: Unit bumblebeed.service entered failed state.
lines 1483-1530/1530 (END)
I've read that specifying nVIDIA BusID helps, so I've done without success:
$ cat /etc/bumblebee/xorg.conf.nvidia
Section "ServerLayout"
Identifier "Layout0"
Option "AutoAddDevices" "false"
Option "AutoAddGPU" "false"
EndSection
Section "Device"
Identifier "DiscreteNvidia"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BusID "PCI:01:00:00"
# If the X server does not automatically detect your VGA device,
# you can manually set it here.
# To get the BusID prop, run `lspci | egrep 'VGA|3D'` and input the data
# as you see in the commented example.
# This Setting may be needed in some platforms with more than one
# nvidia card, which may confuse the proprietary driver (e.g.,
# trying to take ownership of the wrong device). Also needed on Ubuntu 13.04.
# BusID "PCI:01:00:0"
# Setting ProbeAllGpus to false prevents the new proprietary driver
# instance spawned to try to control the integrated graphics card,
# which is already being managed outside bumblebee.
# This option doesn't hurt and it is required on platforms running
# more than one nvidia graphics card with the proprietary driver.
# (E.g. Macbook Pro pre-2010 with nVidia 9400M + 9600M GT).
# If this option is not set, the new Xorg may blacken the screen and
# render it unusable (unless you have some way to run killall Xorg).
Option "ProbeAllGpus" "false"
Option "NoLogo" "true"
Option "UseEDID" "false"
Option "UseDisplayDevice" "none"
EndSection
Manually loading bbswitch or nvidia does not work:
$ sudo modprobe bbswitch
modprobe: FATAL: Module bbswitch not found.
$ sudo modprobe nvidia
modprobe: FATAL: Module nvidia not found.
Of course nouveau module is blacklisted.
I have no clue on what to do.
Last edited by buntolo (2014-08-30 16:28:45)

Updating GRUB from debian worked:
$ systemctl status bumblebeed
● bumblebeed.service - Bumblebee C Daemon
Loaded: loaded (/usr/lib/systemd/system/bumblebeed.service; enabled)
Active: active (running) since sab 2014-08-30 18:30:20 CEST; 4min 53s ago
Main PID: 319 (bumblebeed)
CGroup: /system.slice/bumblebeed.service
└─319 /usr/bin/bumblebeed
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432090] [WARN][XORG] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432105] [ERROR][XORG] (EE) systemd-logind: failed to get session: PID 878 does not belong to any known session
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432107] [ERROR][XORG] (EE) /dev/dri/card0: failed to set DRM interface version 1.4: Permission denied
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432109] [WARN][XORG] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432115] [WARN][XORG] (WW) Unresolved symbol: fbGetGCPrivateKey
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432121] [WARN][XORG] (WW) NVIDIA(0): Unable to get display device for DPI computation.
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432124] [ERROR][XORG] (EE) NVIDIA(0): Failed to initiate mode change.
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432125] [ERROR][XORG] (EE) NVIDIA(0): Failed to complete mode change
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432133] [ERROR][XORG] (EE) /dev/dri/card0: failed to set DRM interface version 1.4: Permission denied
ago 30 18:33:06 biscottyno bumblebeed[319]: [ 169.810097] [ERROR][XORG] (EE) Server terminated successfully (0). Closing log file.
glxgears works as well but strangely I have more FPS with the intel GPU:
$ vblank_mode=0 glxgears
ATTENTION: default value of option vblank_mode overridden by environment.
ATTENTION: default value of option vblank_mode overridden by environment.
45025 frames in 5.0 seconds = 9004.902 FPS
XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0.0"
after 158723 requests (158723 known processed) with 0 events remaining.
$ vblank_mode=0 optirun glxgears
10394 frames in 5.0 seconds = 2078.673 FPS
11030 frames in 5.0 seconds = 2205.821 FPS
10799 frames in 5.0 seconds = 2159.770 FPS
10695 frames in 5.0 seconds = 2138.921 FPS
[VGL] ERROR: in readback--
[VGL] 247: Window has been deleted by window manager
$ vblank_mode=0 primusrun glxgears
ATTENTION: default value of option vblank_mode overridden by environment.
ATTENTION: default value of option vblank_mode overridden by environment.
ATTENTION: default value of option vblank_mode overridden by environment.
ATTENTION: default value of option vblank_mode overridden by environment.
ATTENTION: default value of option vblank_mode overridden by environment.
ATTENTION: default value of option vblank_mode overridden by environment.
13531 frames in 5.0 seconds = 2706.076 FPS
14903 frames in 5.0 seconds = 2980.460 FPS
14857 frames in 5.0 seconds = 2971.345 FPS
14735 frames in 5.0 seconds = 2946.878 FPS
XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0.0"
after 40 requests (38 known processed) with 0 events remaining.
X Error of failed request: BadDrawable (invalid Pixmap or Window parameter)
Major opcode of failed request: 154 (DRI2)
Minor opcode of failed request: 8 (DRI2SwapBuffers )
Resource id in failed request: 0x3200002
Serial number of failed request: 145156
Current serial number in output stream: 145157
glxspheres even show the card in use:
$ vblank_mode=0 glxspheres64
Polygons in scene: 62464
ATTENTION: default value of option vblank_mode overridden by environment.
ATTENTION: default value of option vblank_mode overridden by environment.
Visual ID of window: 0x20
Context is Direct
OpenGL Renderer: Mesa DRI Intel(R) Haswell Mobile
418.895833 frames/sec - 467.487750 Mpixels/sec
326.862103 frames/sec - 364.778107 Mpixels/sec
326.740045 frames/sec - 364.641890 Mpixels/sec
328.897158 frames/sec - 367.049229 Mpixels/sec
$ vblank_mode=0 optirun glxspheres64
Polygons in scene: 62464
Visual ID of window: 0x20
Context is Direct
OpenGL Renderer: GeForce GTX 860M/PCIe/SSE2
213.900274 frames/sec - 238.712706 Mpixels/sec
217.441444 frames/sec - 242.664652 Mpixels/sec
218.784335 frames/sec - 244.163318 Mpixels/sec
217.538555 frames/sec - 242.773027 Mpixels/sec
$ vblank_mode=0 primusrun glxspheres64
ATTENTION: default value of option vblank_mode overridden by environment.
ATTENTION: default value of option vblank_mode overridden by environment.
Polygons in scene: 62464
ATTENTION: default value of option vblank_mode overridden by environment.
ATTENTION: default value of option vblank_mode overridden by environment.
Visual ID of window: 0x20
Context is Direct
OpenGL Renderer: GeForce GTX 860M/PCIe/SSE2
ATTENTION: default value of option vblank_mode overridden by environment.
ATTENTION: default value of option vblank_mode overridden by environment.
339.325698 frames/sec - 378.687479 Mpixels/sec
340.672632 frames/sec - 380.190657 Mpixels/sec
341.477977 frames/sec - 381.089423 Mpixels/sec
341.585143 frames/sec - 381.209020 Mpixels/sec
I will try with Unigine Heaven benchmark, but it will take a while to download it.
I have tried Unigine Heaven benchmark. Intel VGA have big problems because it just shows a blank screen, even if the bencmark is running in the background:
Intel results:
Benchmark results:
Time: 260.741
Frames: 3907
FPS: 14.9842
Min FPS: 10.1115
Max FPS: 28.3029
Score: 377.452
primusrun results:
Benchmark results:
Time: 260.664
Frames: 6977
FPS: 26.7663
Min FPS: 19.2371
Max FPS: 49.1701
Score: 674.243
optirun results:
Benchmark running
Benchmark results:
Time: 260.58
Frames: 5592
FPS: 21.4598
Min FPS: 11.6993
Max FPS: 33.191
Score: 540.573
I would like to understand if theser warnings and errors are harmful problems or not:
ago 30 18:32:39 biscottyno kernel: bbswitch: enabling discrete graphics
ago 30 18:32:40 biscottyno kernel: [drm] Initialized nvidia-drm 0.0.0 20130102 for 0000:01:00.0 on minor 1
ago 30 18:32:40 biscottyno kernel: NVRM: loading NVIDIA UNIX x86_64 Kernel Module 340.32 Tue Aug 5 20:58:26 PDT 2014
ago 30 18:32:40 biscottyno kernel: vgaarb: this pci device is not a vga device
ago 30 18:32:40 biscottyno kernel: nvidia 0000:01:00.0: irq 50 for MSI/MSI-X
ago 30 18:32:40 biscottyno kernel: ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95)
ago 30 18:32:40 biscottyno kernel: ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95)
ago 30 18:32:40 biscottyno kernel: ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95)
ago 30 18:32:40 biscottyno kernel: ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95)
ago 30 18:32:40 biscottyno kernel: ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95)
ago 30 18:32:40 biscottyno kernel: ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95)
ago 30 18:32:40 biscottyno kernel: ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95)
ago 30 18:32:40 biscottyno kernel: ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95)
ago 30 18:32:40 biscottyno kernel: ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95)
ago 30 18:32:41 biscottyno kernel: vgaarb: this pci device is not a vga device
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432079] [WARN][XORG] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432090] [WARN][XORG] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432105] [ERROR][XORG] (EE) systemd-logind: failed to get session: PID 878 does not belong to any known session
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432107] [ERROR][XORG] (EE) /dev/dri/card0: failed to set DRM interface version 1.4: Permission denied
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432109] [WARN][XORG] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432115] [WARN][XORG] (WW) Unresolved symbol: fbGetGCPrivateKey
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432121] [WARN][XORG] (WW) NVIDIA(0): Unable to get display device for DPI computation.
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432124] [ERROR][XORG] (EE) NVIDIA(0): Failed to initiate mode change.
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432125] [ERROR][XORG] (EE) NVIDIA(0): Failed to complete mode change
ago 30 18:32:41 biscottyno bumblebeed[319]: [ 144.432133] [ERROR][XORG] (EE) /dev/dri/card0: failed to set DRM interface version 1.4: Permission denied
ago 30 18:33:06 biscottyno kernel: ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95)
ago 30 18:33:06 biscottyno kernel: [drm] Module unloaded
ago 30 18:33:06 biscottyno kernel: bbswitch: disabling discrete graphics
ago 30 18:33:06 biscottyno kernel: ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95)
ago 30 18:33:06 biscottyno kernel: pci 0000:01:00.0: Refused to change power state, currently in D0
ago 30 18:33:06 biscottyno bumblebeed[319]: [ 169.810097] [ERROR][XORG] (EE) Server terminated successfully (0). Closing log file.
lines 1508-1555/1555 (END)
Last edited by buntolo (2014-08-30 17:43:05)

Deflation Animation not Working

Hi,
I have got a code from this forum which create a ellipse on the client area. First it creates a rectangle equivalent to the size of client area. I have put the deflation code in the ::OnTimer( ....) but its not working.
void CTestingCode1View::OnDraw(CDC* pDC)
CTestingCode1Doc* pDoc = GetDocument();
ASSERT_VALID(pDoc);
if (!pDoc)
return;
GetClientRect(&rect);
//CRect rc(rect.TopLeft().x+10, rect.TopLeft().y+10,rect.BottomRight().x-10,rect.BottomRight().y-10);
//CDC *pDC = GetDC();
CDC WorkDC;
CBitmap memBmp, * pOldMemBmp;
WorkDC.CreateCompatibleDC(pDC);
memBmp.CreateCompatibleBitmap(pDC, rect.Width(), rect.Height());
pOldMemBmp = (CBitmap *)WorkDC.SelectObject(&memBmp);
int oldBkMode = WorkDC.SetBkMode(TRANSPARENT);
WorkDC.Ellipse(rect);
WorkDC.SetBkMode(oldBkMode);
// WorkDC.BitBlt(0, 0, rect.Width(), rect.Height(), pDC, 0, 0, SRCCOPY);
//pDC->BitBlt(0, 0, rect.Width(), rect.Height(), &WorkDC, 0, 0, SRCCOPY);
pDC->BitBlt(rect.left, rect.top, rect.Width(), rect.Height(), &WorkDC, 0, 0, SRCCOPY);
WorkDC.SelectObject(pOldMemBmp);
pOldMemBmp->DeleteObject();
// TODO: add draw code for native data here
}void CTestingCode1View::OnTimer(UINT_PTR nIDEvent)
// TODO: Add your message handler code here and/or call default
rect.DeflateRect(10,10);
CView::OnTimer(nIDEvent);
int CTestingCode1View::OnCreate(LPCREATESTRUCT lpCreateStruct)
if (CView::OnCreate(lpCreateStruct) == -1)
return -1;
SetTimer(1,200,NULL);
//#3016
//@R0
//return -1;
//#3016
//@R0
//#3016
// @R0
// TODO: Add your specialized creation code here
//@R0
return 0;
CReact is declared as a class variable in *view.h. Some body please guide me.
Zulfi.

Hi my friend,
I am able to calculate the values for initial line like ellipse at the start of inflation process by trial and error process. The values are part of OnDraw(...) method. There is a little bit flicker when the inflation ellipse is maximized.
#include "stdafx.h"
// SHARED_HANDLERS can be defined in an ATL project implementing preview, thumbnail
// and search filter handlers and allows sharing of document code with that project.
#ifndef SHARED_HANDLERS
#include "DefInflate2.h"
#endif
#include "DefInflate2Doc.h"
#include "DefInflate2View.h"
#ifdef _DEBUG
#define new DEBUG_NEW
#endif
// CDefInflate2View
IMPLEMENT_DYNCREATE(CDefInflate2View, CView)
BEGIN_MESSAGE_MAP(CDefInflate2View, CView)
// Standard printing commands
ON_COMMAND(ID_FILE_PRINT, &CView::OnFilePrint)
ON_COMMAND(ID_FILE_PRINT_DIRECT, &CView::OnFilePrint)
ON_COMMAND(ID_FILE_PRINT_PREVIEW, &CDefInflate2View::OnFilePrintPreview)
ON_WM_CONTEXTMENU()
ON_WM_RBUTTONUP()
ON_WM_CREATE()
ON_WM_SIZE()
ON_WM_TIMER()
ON_WM_ERASEBKGND()
END_MESSAGE_MAP()
// CDefInflate2View construction/destruction
CDefInflate2View::CDefInflate2View()
// TODO: add construction code here
CDefInflate2View::~CDefInflate2View()
BOOL CDefInflate2View::PreCreateWindow(CREATESTRUCT& cs)
// TODO: Modify the Window class or styles here by modifying
// the CREATESTRUCT cs
return CView::PreCreateWindow(cs);
// CDefInflate2View drawing
void CDefInflate2View::OnDraw(CDC* pDC)
CDefInflate2Doc* pDoc = GetDocument();
ASSERT_VALID(pDoc);
if (!pDoc)
return;
CRect cr;
int cx, cy;
GetClientRect(&cr);
CDC WorkDC;
WorkDC.CreateCompatibleDC(pDC);
CBitmap memBmp;
memBmp.CreateCompatibleBitmap(pDC, cr.Width(), cr.Height());
CBitmap *pOldMemBmp = (CBitmap *)WorkDC.SelectObject(&memBmp);
CBrush background(0xFF0000);
WorkDC.FillRect(&cr, &background);
if (m_running)
WorkDC.Ellipse(m_rect);
else {
m_running = true;
SetTimer(1234, 50, 0);
GetClientRect(&cr);
if(deflation) {
m_rect.left = 0;
m_rect.top = 0;
m_rect.right = cr.right;
m_rect.bottom = cr.bottom;
else {
m_rect.left = (cr.left+cr.right)/2 -150;
m_rect.top = (cr.top+ cr.bottom)/2;
m_rect.right = (cr.left+cr.right)/2 +150;
m_rect.bottom = (cr.top+ cr.bottom)/2;
//Special Assigned values
m_rect.left = 200;//cr.left;//+cr.right-20;
m_rect.top = (cr.top+ cr.bottom)/2;//cr.bottom/2;
m_rect.right = 100;//0;//cr.left+cr.right+20;
m_rect.bottom = (cr.top+ cr.bottom)/2;//0;//cr.bottom;*/
WorkDC.Ellipse(m_rect);
pDC->BitBlt(0, 0, cr.Width(), cr.Height(), &WorkDC, 0, 0, SRCCOPY);
WorkDC.SelectObject(pOldMemBmp);
// TODO: add draw code for native data here
// CDefInflate2View printing
void CDefInflate2View::OnFilePrintPreview()
#ifndef SHARED_HANDLERS
AFXPrintPreview(this);
#endif
BOOL CDefInflate2View::OnPreparePrinting(CPrintInfo* pInfo)
// default preparation
return DoPreparePrinting(pInfo);
void CDefInflate2View::OnBeginPrinting(CDC* /*pDC*/, CPrintInfo* /*pInfo*/)
// TODO: add extra initialization before printing
void CDefInflate2View::OnEndPrinting(CDC* /*pDC*/, CPrintInfo* /*pInfo*/)
// TODO: add cleanup after printing
void CDefInflate2View::OnRButtonUp(UINT /* nFlags */, CPoint point)
ClientToScreen(&point);
OnContextMenu(this, point);
void CDefInflate2View::OnContextMenu(CWnd* /* pWnd */, CPoint point)
#ifndef SHARED_HANDLERS
theApp.GetContextMenuManager()->ShowPopupMenu(IDR_POPUP_EDIT, point.x, point.y, this, TRUE);
#endif
// CDefInflate2View diagnostics
#ifdef _DEBUG
void CDefInflate2View::AssertValid() const
CView::AssertValid();
void CDefInflate2View::Dump(CDumpContext& dc) const
CView::Dump(dc);
CDefInflate2Doc* CDefInflate2View::GetDocument() const // non-debug version is inline
ASSERT(m_pDocument->IsKindOf(RUNTIME_CLASS(CDefInflate2Doc)));
return (CDefInflate2Doc*)m_pDocument;
#endif //_DEBUG
// CDefInflate2View message handlers
int CDefInflate2View::OnCreate(LPCREATESTRUCT lpCreateStruct)
if (CView::OnCreate(lpCreateStruct) == -1)
return -1;
m_running= false;
/*#3016
@R0
return -1;
#3016
@R0
#3016
@R0
// TODO: Add your specialized creation code here
@R0*/
return 0;
void CDefInflate2View::OnSize(UINT nType, int cx, int cy)
CView::OnSize(nType, cx, cy);
m_rect.left = 0;
m_rect.top = 0;
m_rect.right = cx;
m_rect.bottom = cy;
if (!m_running)
SetTimer(1234, 50, 0);
m_running = true;
deflation=1;
start = true;
// TODO: Add your message handler code here
void CDefInflate2View::OnTimer(UINT_PTR nIDEvent)
// TODO: Add your message handler code here and/or call default
CRect cr;
int width= m_rect.Width();
int ht = m_rect.Height();
if (deflation) {
if (width<=0 || ht<=0){
deflation=0;
KillTimer(1234 );
m_running=false;
Invalidate();
else {
m_rect.DeflateRect(1,1,1,1);
Invalidate();
else {
GetClientRect(&cr);
width= cr.Width();
ht = cr.Height();
if (m_rect.Width() >= width || m_rect.Height() >= ht ) {
deflation=1;
KillTimer(1234 );
m_running=false;
Invalidate();
else {
m_rect.InflateRect(1,1,1,1);
Invalidate();
CView::OnTimer(nIDEvent);
BOOL CDefInflate2View::OnEraseBkgnd(CDC* pDC)
// TODO: Add your message handler code here and/or call default
return true;
return CView::OnEraseBkgnd(pDC);
Many thanks for your guidance.
Zulfi.

Not work tablet UI on Prestigio 5080 PRO tablet

I read that browser.ui.layout.tablet = "1" can fix this problem. But it not works. I can work only in pnone interface that is not good for my 8'' tablet.

Would it be possible for you to share the problematic pdf and OS information with us at [email protected] so that we may investigate?
Thanks,
Adobe Reader Team

Why self-defined access sequences of free goods can not work?

Hi gurus,
I have maintained access sequences of free goods self-defined.but when i creat the SO it does not work!
when i used the standard access sequences ,it is OK .
Can anybody tell me why?
thanks in advance

Dear Sandy,
Go to V/N1 transaction select your self defined access sequence then go in to the accesses and fields and check all fields are activated.
Make sure that these fields are flowing in your sales order.
I hope this will help you,
Regards,
Murali.

Adobe bridge raw not working with windows vista in photoshop cc, why?

adobe bridge raw not working in photoshop cc, is there a fix?

Your sure your using photoshop cc on windows vista?
I was under the impression that photoshop cc would not even install on windows vista.
What version of camera raw do you have?
In photoshop under Help>About Plugin does it list Camera Raw and if so which version is it?
(click on the words Camera Raw to see the version)
Camera raw doesn't work if it's a camera raw file or some other file type such as jpeg or tif?
What camera are the camera raw files from?
Officially camera raw 8.3 is the latest version of camera raw that will work on windows vista.

Adobe Bridge CS5 in windows 7 not working?

Adobe Bridge CS5 in windows 7 not working. I was using bridge perfectly for last 2 years. It stops working since 3 days. I tried to install updates. Showing some error to install.
Tried to install creative cloud..again some error. Error code : 82
Could you please advice how I can fix my adobe bridge.

https://www.youtube.com/watch?v=xDYpTOoV81Q&feature=youtu.be
please check this video I uploaded..this is what happens when I click adobe bridge.. just blinks and go off. bridge not working on task manager

ADOBE CLOUD ON MY DESKTOP WILL NOT WORK. IT LOADS UP BUT NOTHING FILLS THE WINDOW

ADOBE CLOUD ON MY DESKTOP WILL NOT WORK. IT LOADS UP BUT NOTHING FILLS THE WINDOW

BLANK Cloud Screen http://forums.adobe.com/message/5484303 may help
-and step by step http://forums.adobe.com/thread/1440508?tstart=0
-and http://helpx.adobe.com/creative-cloud/kb/blank-white-screen-ccp.html

Partner application logoff not working

We have a partner application registered with sso with custom login screen. The login works fine. We use the following code to logoff the partner application in logoff.jsp
response.setHeader("Osso-Return-Url", "http://my.oracle.com" );
response.sendError(470, "Oracle SSO");
session.invalidate();
but the logoff is not working properly. It is not invalidating the session and the logout http request is not going from the application server to the sso server.
Are there any additional configurations for SSO logoff.Any help is appreciated.
Thanks

Hi
The WF should also trigger if i add the Partner function in UI.If i change any Attribute the WF triggers but i dont want to change the attribute when i add the partner function.
If i have only one event for WF that is Partner Change the WF will not trigger it for the 1st time when i save the UI. But next i come to the same saved doc and add a partner function then the Wf triggers.
So this means that Partner change is active.
the issue here is i need to trigger the WF on , the 1st time i save the UI, for which i wil be using Attribute Change and next time when i come back to saved doc the and add only the partner function and no changes are made to attributes the WF should again trigger.
Thanks
Tarmeem

Ellipsis 7 not working

Similar Messages

Maybe you are looking for