EMac won't boot to hard drive - Flashing Folder at Startup

I did have this eMac working with this Hard Drive months ago. Now I just get the Folder with the Flashing icon at Startup. So I installed OSX Tiger on a Firewire External Drive & it Works perfectly running from the FW HD. The Internal Hard Drive then shows up on Desktop. I run Disc Permissions & Verifications on the Internal Drive & everything comes up Perfect. It just won't Boot to the Internal Hard Drive. I even used Super Duper to make a Clone of the Firewire Hard Drive that is running, but Still I get the Flashing Folder with The Finder Face, when I unplug the Firewire Drive & attempt to boot from Internal HD. Any clue? Thank you in advance.

I run Disc Permissions & Verifications on the Internal Drive
Run Repair Disk on the eMacs internal disk.
If it passes then open the System preferences > Startup Disk and select the eMac's disk.

Similar Messages

  • Lombard won't boot to Hard Drive

    I erased and installed 10.3, once that is done it restarts and works great. Then after I turn it off, or restart again, or unplug AC adapter from the wall it will not boot to hard drives, boots to the circle slash. I booted to install cd and ran disk utilities then when I restart nothing. The only time I can get the powerbook to work is right after I install 10.3. The date/time is always remembered, but I do have a dead battery - won't hold charge at all. Thinking about buying battery, just really thought I should be able to run the laptop on ac adapter. Any thoughts are greatly appreciated.

    TJ,
    Welcome to the Discussions.
    See if the suggestions in this article, especially the resetting of the PRAM and power manager help:
    http://docs.info.apple.com/article.html?artnum=106805
    One issue the Lombard suffers more than other black G3s is a failed backside L2 cache. Once you are up and running again, go to the System Profiler > Hardware and see if it reports either 512K or 1MB of L2 cache or is missing. If this is the case, resetting the power manager, at least when running 9.x, will allow a successful start, but of course the problem is still present.
    If you have a bootable OS 8.6 > 9.2.2 CD, and from a cold start, not restart, boot to the CD and see if you get a warning dialogue that there is a problem with RAM or cache memory.
    Message was edited by: jpl

  • Computer won't boot; no hard drive spin up; no target mode; refuses cd.

    Our "other" house computer, an iMac 400 DV, vintage 1999, worked fine until just a little while ago. Last used this morning to send e-mail, it now will not boot. Hard drive does not spin up. After pushing power button, light (behind button) comes on, but no further activity ensues. Cannot be started in target disk mode. Utility CD cannot be inserted, either before or after pushing power button. My guess is that HD is "OK" (such as that is after 10 years), but that power is not getting to bus that drives it or CD drive.
    How to find broken connection, if that what it is, is the problem.
    Wise counsel or off the wall guesses are welcome.
    Thanks.
    Leonard
    (p.s.: in one or more other forums, I posted questions in the last few months; subsequently I have been indisposed, as they say. My apologies to anyone who may have written with helpful tips and to whom I have not yet replied. I am way behind in correspondence and beg your indulgence until I can sit still long enough to type a few words in reply (hopefully after I've tried your suggestions).

    Pismo is great. It's still my portable Mac, and as long as I don't try to play "HD" video in full screen mode on YouTube or Hulu, it is perfectly fine for most things I do. It still does not look old when I pull it out in a public place. Recent switchers with their MacBooks are probably wondering why the Apple logo is up-side-down.
    My G4 card is the one that was sold by FastMac. 550 MHz. It is noticeably faster because Mac OS X and applications (such as for video processing) use the vector processing unit in the G4. But because the clock speed is not that different from the original 500 MHz G3, it's not a drastic end-to-end type of improvement.
    When the CPU is being loaded to max, it does get hotter than the stock G3, so the fan comes on more often. The problem with today's Internet is the use of Flash animations in banner and sidebar ads. Those things put unnecessary load on my Pismo's CPU. For modern computers, that extra load is no big deal, but it matters to a 550 MHz G4. I would just turn Flash off, but there are things that I do want to see that use Flash.
    I got it at the FastMac booth at the Macworld Expo a few years ago for the +show price+, so it has been worthwhile to have it.

  • My Mac Pro flashes the question mark and wont boot from hard drive, flash, or Cd... Please help!

    My Computer froze so I shut it down... When I tryed to boot up again it wouldn't power up.  After a few tweeks I got it to power up but now it wont boot from the hard drive, flash drive or a cd.  It want to start, then, after a few seconds it stops.  Not sher what to do.  Can anyone help?

    Have you tried Safe Boot?
    You also might reset PRAM and reset SMC.
    Have you tried booting with the Recovery System? See its possibilities here.
    From there you can make repairs to your primary startup partition.
    Do you have a backup? If not, do you have an external drive large enough to back up your primary drive? It would be good to have one in case your drive needs repair or replacement.

  • K8M Neo-V won't boot from hard drive after BIOS flash

    But it boots just fine from CD or floppy.
    I bought the combo (MB, AMD64 processor, 1G memory) to replace a
    motherboard which had died in a previously working system.  At the
    same time I replaced the power supply and the video card. When I first
    fired it up, it brought up the boot manager from the previous incarnation
    of the system, which had been an Athlon-XP.
    I never actually let it reboot, since I wanted to redo the OS optimized
    for the AMD64 (and the new video card.)  I flashed the motherboard to the
    most current version of the BIOS (AMI version 3.5), booted from CD and
    installed the OS.  Once I got to the point of being able to boot from the
    new system, I removed the CD and proceeded to reboot.
    It displayed all the possible boot devices (note that the floppy and CD
    were empty):
      Searching for Boot Record from floppy..not found
      Searching for Boot Record from CD/DVD..not found
      Searching for Boot Record from IDE-0..not found
    No matter what I did, I couldn't get the system to boot from the hard
    drive.  I reflashed the BIOS back to 3.2, still didn't work.  Since then I
    have installed four different operating systems:  Win2k, WinXP, Gentoo
    Linux and Debian Linux.  All boot from CD, install perfectly until you get
    to the part where the system has to boot on its own, and then nothing.
    Has anyone seen this?  Is it possible that there is a problem with how
    I've set the BIOS up?  Or a hardware conflict with something else?  Or
    just a bad MB?
    Thanks for any advice.
    Steve

    Notihng special in the BIOS drive setup.  Everything is auto-detected and I've pretty much left those settings alone.  At the time of the first flash I probably *did* have SMART enabled.  Once I started having trouble I turned that off, and have never turned it back on.
    Boot order has been changed multiple times.  Right now it is floppy -> cd -> ide-0.  I've turned the network boot option off and on again (not that there's a boot server handy...)  I've tried hitting F11 to choose my boot device and specifically selected the HD.  Hasn't made any difference.
    I generally turn virus protection off the moment I get a new motherboard.  I'm pretty sure it came disbaled by default, if not I'm sure I disabled it.  Even had it been on, though, any boot block corruption would have to be permanent damage to act like it has, since four subsequent OS installs should have overwritten the boot block four times over.
    It might be worth my time to drop a different HD in the primary master slot and see if it can boot from that.  I'll be real unhappy if I've toasted a perfectly good drive.

  • S10-2 Won't boot from hard drive

    I have an S10-2 2957 that won't boot from the internal hard drive. The one key function doesn’t work either. After the splash comes up and the BIOS runs all that is displayed is a flashing cursor. If I boot from an external source (USB CD) I can see the hard drive and all files are intact. I have tried removing the battery and power supply, holding the power key for 30 seconds before powering the unit back up to no avail. I’m thinking that either the boot sector is corrupt or the first partition is not active. Any ideas?
    Solved!
    Go to Solution.

    press f8 to load when you see lenovo logo at start-up, and select safe mode. post back the results.

  • G3 won't boot from hard drives or startup (original) CDs

    I recently installed OS X 10.4 on my Mac G3 (6GB HD, 256MB Ram, blue & white). It ran fine for one week. After one week, when it would boot up, I would have 800 MB of free space. Within a few minutes I would get an out of memory error and my HD would have zero space left...effectively locking up the machine. I was told to increase my memory to 1GB (I did) and to install a new HD (I did, a Seagate 80GB). I partitioned the Seagate into two equal partitions. About the time that the OS finished this task, I received a security upate installation dialogue asking me in install a new security update. I said "OK". About the time the security update was installed, the system ran out of memory...then asked me to restart the machine. I have not been able to get it to restart since. Can't startup with the OS9 CD, the OSX CD OR Diskwarrior. I keep getting the same message..."panic(cpu 0 caller 0x002DE020): Unable to find driver for this platform: "powerMac1,1". Then there is a whole lot of other stuff with a final comment "We are hanging here..." I can't seem to find anyone to help me with this. I brought the machine back to its orginal configuration...didn't work. I disconnected the old 6GB HD and was able to install OSX on the new drive...but, after installing on the new hard drive, I rebooted and I am back to the same errors. I keep getting the OS9 flashing folder with "?"/face. HELP!
    Thanks,
    Pat
    G3 Blue & Whote   Mac OS X (10.4.4)  

    You are having kernel panics as shown in this Apple doc.#106227.
    Do everything, in order, in Dr.Smokes Resolving Kernel Panics and don't leave out any steps.
    Quote from Dr.Smoke "My FAQ is a roadmap: start at the beginning and work through to the end, following the instruction in the order specified, including the "If all else fails..." section if a cause or resolution is not found in an earlier troubleshooting step therein"
    Here's more at a brody's KP site.
    Cheers!
    DALE

  • Powerbook won't boot from hard drive or restore disk

    I've looked through some of the older posts here and none of them exactly matches my problem, and I've tried just about any possible solution I can think of.
    I recently noticed that my PowerBook was acting a bit strange. It was making more fan noises than usual, and sometimes the computer would make the very last noise it makes as it shuts down (which is the hard drive coming to rest, I suppose?), though the computer would still be running. Then, yesterday the computer froze and I hit command-control-power, and when the computer restarted it gave me a folder icon blinking between a question mark and the Mac logo.
    I tried restarting again, but I had no luck. Now when I try to start up I get the start-up chime, then I get one of three things:
    1) If I restart it without a CD in the drive, I get the blinking folder.
    2) If I restart it with the Software Restore and Install DVD in (but without holding down the C key), it gets to the Apple logo and shows the spinning pinwheel or whatever you want to call it, then freezes and some nasty horizontal bars pop across the screen.
    3) If I restart it with the Restore & Install DVD in and I hold down the C key, it gives me the Apple logo, then the "Your computer has encountered a problem and needs to be restarted" box pops up.
    I tried zapping the PRAM--no luck. I tried Open Firmware; the screen pops up, then I type in "mac-boot" and I get the same thing as in #2 above.
    I used the Hardware Test CD; it told me that there was a Mass Storage error with the error code 2STF/1/4. That doesn't sound too pleasant.
    I'm not sure what caused it; perhaps it was a heat thing, but I moved it too a different surface. All the hardware is original except for the Airport card, which has worked fine since Christmas. The only recent software changes I've made were updating to the newest versions of iTunes and Firefox. It doesn't seem like a hard drive problem, since the boot CD won't work.
    Am I doomed to sending Apple a couple hundred bucks to fix this? The laptop is right at three years old, so even if I'd had AppleCare it would be expiring right about now. Or is it time to buy one of those MacBooks? Or just buy a couple PC's and use each one till it breaks, then throw it out?
    Thanks,
    Kevin

    I finally got to another Mac. I installed Mac OS X onto my Firewire drive, then hooked up the drive to my Powerbook and used the Startup Manager. The drive showed up on Startup Manager and I chose to boot from it. When I did, the startup process continued briefly, then froze just like it does when I try to boot from the CD.
    I know my Powerbook's hard drive is shot, and to be honest, I'm fine with that--there isn't any critical, essential data on there. I tried starting the Powerbook up in Target Disk mode, but that doesn't work either--I hear the chime, press T, but the screen stays black.
    Now my question is: can I rip the hard drive out? Or do I have not only a bad hard drive, but also something else gone wrong? I'm not opposed to buying a new internal hard drive and installing it myself if that will fix the problem; what I don't want to do is spend a few hundred bucks to take it to someone who's only going to tell me that my omputer is now a paperweight.
    Also, my Powerbook isn't one of the ones with a recalled battery. The computer can get pretty hot, even when sitting on a desk, but I just figured that was normal.
    Thanks,
    Kevin

  • Ibook g4 won't boot, but hard drive seems fine

    I have a ibook g4,800mhz. osx 10.4.8
    On start up i get the folder & question mark. I have tried the following.
    1) i booted with an os install disk. disk utilities reported the drive was ok it but couldn't see a disk partition so disk first aid had nothing to do.
    2) next i ran disk warrior which had the same probably, it could see the hard drive, reported that the drive was functioning, but saw no partition.
    3) finally i gave up and reformatted the disk, and re installed an os. this worked for 48 hours at which time the problem came back.
    4) i can put the laptop in firewire mode connect it to a desktop and access the hard drive. I can format the disk using apple disk tools, i can install an new os, but after all this it still won't boot from the internal hd.
    5) I reset the pram. also tried starting up with the option key down .. no hard drive is visible when i do this.
    So the hard drive seems to work ok. Two different disk utilities see the hard drive and think its functioning ok. OSx installer runs without complaint, but the &$%! won't boot from the hd.
    Anybody got any suggestions?

    ...this worked for 48 hours at which time the problem came back...
    This is the time period that I was commenting on. If something was used during that time that corrupted the OS, it would cause the situation you are in.
    If everything is perfect with the OS then something is wrong with the hard drive or the motherboard's interface to the hard drive.

  • Kernal panic/ won't boot from hard drive or installation disc/ error type 1

    Friends PowerBook seems to be dying or is possibly dead.
    PowerBook G4 model A1138 or M9969LL/A:
    15 inch/ 1.67 ... http://support.apple.com/specs/powerbook/PowerBookG4_15-inch_Double-LayerSD.html
    K, so my friend's powerbook is in my possession... and not booting.
    A week ago, upon booting the laptop, he'd get the old OS9 looking folder flashing with THE happy face and then a question mark. Then, usually, it'd boot. It started taking longer and longer to boot, so he backed up all his stuff. It eventually stopped booting OSx (10.4.10) and came to me asking about how to reinstall Tiger.
    As of right now his machine will NOT boot from the hard drive, regularly or in safe mode.
    When we try the install CD, we get a kernal panic. It hangs, then tells us to restart. Every time.
    Holding down "alt" I tried the hardware diagnostic/ repair thingy from the install disc. It mentions a quick issue with finding Gineva fonts or something and then gives the following errors:
    type 1346978644 error 1
    type 1346978644 error 1
    Invalid memory access at %SRR0:00000000 %SRR1:00083030
    Thats about all we got. We are looking for a screw driver to try and remove a stick of ram and see if thats the problem. Any ideas? Hoping for a bad stick of ram or hard drive. Anyone know if for sure the logic board is dead or if there is a way to fix it? Appreciate any feedback. Happy to give more information if you need it!
    ~joel

    When you did the boot off the original system disk was anything non-Apple externally connected? If not, then you clearly have a hardware problem, and your idea of examining the RAM is not half a bad idea. The only thing you might want to do before that is zapping the PRAM. Sometimes that clears issues such as you describe:
    1. First determine if your machine is under 4 years old. If it is, then go ahead
    and do step 2. Otherwise do step 3.
    2. http://docs.info.apple.com/article.html?artnum=2238
    3. Take it to an authorized service center to have the clock battery replaced. That may cause the very issues you described.

  • Macbook won't boot from Hard Drive of Disc Drive!

    So I bought a Macbook (Mid-2010) from a friend recently and I can't seem to get it to boot from the hard drive or optical drive. At first I tried booting from the HD it already had and when I didn't have any luck, I went out and bought a new one. It still won't boot. I'll turn it on, it'll chime and will try to load, and then I'll get the "You need to restart your." message. I've tried booting from disc (Leopard & Snow Leopard) and will still get the same message. I have also tried all possible startup key combinations and haven't had any luck. I don't have the original DVD it came with. So was wondering if any of you guys out there have experienced this. I would like to hear your tips before I go to an Apple Store and see if they can get it fixed for me.

    "You need to restart your." message
    That is referred to as a "kernel panic"...
    Try here >  Tutorial: Avoiding and eliminating Kernel panics | MacFixIt - CNETReviews
    I don't have the original DVD it came with
    You will need those discs.   Replacement disc(s) from Apple:   You can get replacement System Install & Restore CD/DVDs from Apple's Customer Support - in the US, (800) 767-2775 - for a nominal S&H fee. You'll need to have the model and/or serial number of your Mac available.
    You can check the startup disk using the Disk Utility application located in /Applications/Utilities if you can boot in Safe Mode, but you cannot make repairs without the install disc.

  • EMac won't see external hard drive.

    I have a 1.42 GHz eMac and I have all of my iTunes stuff on an external hard drive via FireWire. I went to turn the hard drive on, which I've done for the past 4 months, and it came on but wouldn't show up on my eMac. I went to disk utility, but it froze and I had to force quit it. I tried connecting it via USB, and it works fine on other computers, any ideas on how to make it work again? I've unplugged the system for 4 hours and reset the PRAM. Nothing seems to be working...

    USB and FireWire Quick Assist
    http://support.apple.com/kb/HT1151?viewlocale=en_US
    What to do if your computer won't recognize a FireWire device
    http://docs.info.apple.com/article.html?artnum=88338
    Dealing with FireWire problems (drives not mounting, devices unrecognized, etc.)
    http://www.macfixit.com/article.php?story=20041221081432908
     Cheers, Tom

  • IMac turned off suddenly, won't boot from hard drive/CD drive

    Hi guys.
    Here is what I have:
    27" iMac with:
    Core i5 2.7
    4GB RAM
    Mountain Lion
    Win7 on Bootcamp
    Lion is installed, but I have the Snow Leopard install disc.
    The system had just been recently reformatted so there wasn't really much on the computer itself other than an update to Mountain Lion and a Win7 install via Bootcamp. Other than that, nothing was recentlly installed.
    What happenes is I was browsing and all of a sudden it completely shut down. No warning, nothing. Completely shuts down.
    Okay.. weird... but when I try to load Mac back up, the Apple logo appears and then after a while of supposedly loading, the screen goes to a plain white screen until I force the computer off. Something similar happens when tryin gto boot into Windows: I get to the "Starting Windows" screen but after that everything goes black and I have to shut down manually.
    Great. Now I'll just go into recovery and fix all of this right? Wrong. Can't boot into recovery either. Similar end result: white screen.
    Last thing I tried is reinstall OS X Snow Leopard. After loading for about 1-2 minutes, the usual white screen appears after trying to boot from the disc.
    I am at a loss. I don't think its the hard drive, because the problem occurs even when trying to boot from the disc. My suspicion is the RAM has gone bad. But, before I go the hardware route, is there any suggestions or recommendations anyone could make first?
    In advance, I really appreciate anyone who replies and tries to help.
    Thanks.

    Xmotox,
    I had the EXACT problem today. EXACT. Discs wouldn't boot, I did get the application disc to run the AHT but it said all was fine.
    I called my buddy who said something about unplugging for a minute then holding power button while plugging the power supply back in. I thought it would be futile since we already did all the SMC reset procedures to no avail, PRAM reset didn't do anything, etc, etc... But what do you know, up pops the disc utility and my iMac is now restoring from time machine. It's not done yet, so I can't say it worked... BUT it's the farthest we got tonight. Could not get disc utility up via CMD-R or OPTION keys... but powering down, unplugging for a minute or so, then holding power button while plugging the power supply back in did the trick. Hope this helps!

  • IMac G5 won't boot to hard drive or cd

    Please, someone help me.
    My iMac G5 crashes (power is lost completely) during boot every time, about 10 seconds after the cog-wheel progress indicator comes on. When I try booting to a cd by holding down the option key, the only boot device that shows is the hard drive.
    I have replaced the ram.....twice. No luck. And, yes, I pushed the ram in really hard.
    I hooked my hard drive up to my friends hackintosh to use the disc utiliity and this is what I get:
    "Invalid Key Lenght
    Invalid node structure
    Volume check failed
    Filesystem verify or repair failed"
    I bought the imac off craigs list a year ago, and I didn't get the original leopard disc, but I've tried diskwarrior and other bootable repair tools, and the mac never seems to see them. I've even tried using them in an external CD drive with no luck. I don't want to go buy OS X if my mac isn't going to read the disc.
    Any suggestions as to what is going wrong and how I can fix it?

    Thanks for posting back, gld your problems were solved. It's always a good idea to have an external firewire backup/clone (I use SuperDuper!), you could have booted from that.

  • MacBook won't boot from hard drive or CD

    My MacBook will not turn on. When the power button is pressed the chime sounds as normal and the grey screen appears but it will not go any further. It also refuses to boot from a CD when c is held down. The CD spins up but it does not load. The computer was water damaged in December and this killed the hard drive but I replaced it and it worked fine again for about a month. Does anyone have any suggestions?

    Thanks for the advice, doesn't seem to have worked though.

Maybe you are looking for