Emails deleting themselves on Blackberry Pearl after a few hours

I have set up an Email account on my Blackberry Pearl for a UKmail Exchange email account so I can see my emails on my Blackberry. However after a few hours the incoming emails are deleting themselves only leaving the sent emails. Emails are deleting themselves before I can see them.
I've looked in Email Settings but there doesn't seem to be anything I can do to stop them. Has anyone had the same problem?

Check and see if your WiFi is on. I had (have) the same problem when I leave it on and go to work. The phone constantly searches for WiFi and the battery at a record pace. I turn it on only when I am at home or where I can access WiFi, other times I leave it off.
I also hear the Ebay app is a huge drain.
I also limited the home pages, I had over twelve that i think were constantly updating. I limited it to one.
Maybe one or all of these will help.
Regards.
It's always funny when it's someone else.

Similar Messages

Iphone 5s - IBM Notes Traveler 9.01 -Unable to move messages to trash after a few hours

I have a problem with one of my Iphone 5s users. Everything was working with his IPhone 4S, but the phone died and so they replaced it with a 5S
We are using an IBM Lotus Notes 9.01 Server (latest FP patch) and Traveler 9.01 FP4 with the iphone 5 s.
On his Iphone 5S we install Notes Traveler... Everything works on it, but after a few hours we not able to delete messages on the IPhone. When he clicks Delete on a message on his Iphone, it comes back saying it is "Unable to Move the message"
If I remove Traveler and reinstall it, he can delete the messages for a few minutes or even a few hours, but then it comes back and says it cannot move the messages when we try to delete the email on the Iphone 5S.   The Iphone had   7.1.1 OS... I updated it to latest Apple 7.1.2 OS on it.. Same problem.   We also have an AOL account on the Iphone ....that works fine...      All other Traveler users on Iphones 4S or 5S users are working Fine...
I had IBM look at it. They did some testing and the email deletions only appeared on the logs when   it synchronized to Traveler, but when the problem occurs... it never did show anything in the Notes logs, about the Delete request.   They are saying it is an Apple problem.
I even reset his IPhone 5 S to factory defaults and re-setup Notes Traveler and after a few minutes or a few hours... When he deletes a email he gets the Cannot move the messages again.   I opened a bug report with Apple by never heard back from them. All other functions of the email work..   He can send and receive emails... He just cannot delete after a few hours. I ran checks on he email database and everything comes up OK...

That's odd. You will probably have to contact Apple support on this one. I'm not sure if their is a problem with your account or a server glitch at their end but in either case, they will probably have to look into it for you. You can reach them here: http://www.apple.com/support/icloud/contact/.

Unable to boot Z10, stuck on loading screen at 99% after a few hours.

Hi, I am unable to boot Z10, stuck on loading screen at 99% after a few hours. I did not try to update, nor load any other OS versions. Running a Bell Canada 10.1. Tried to pull battery, leave phone boot for 5 hours, still stuck on 99%. I tried plugging it in BB Link and computer will not recognize it.

dazedandconfused wrote:
Every option Im seeing is telling me Im going to lose my data... is this true? I know with other phones ppl are able to mount the device as if it were a hard drive and pull content from it... is this not possible with the Z10? Thanks...
I understand you are frustrated and seeking solutions, but please don't double and triple post your inquiry.
I've answered your thread already, here:
Re: Z10 stuck on loading logo on starting up
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Dv5t-1000 CTO Sound sputters and OS slows down after a few hours

I am running Vista 32bit SP1 on a DV5T-1000 CTO machine, 4gb ram 2.0ghz c2d
I've noticed that after a few hours of use, usually after I leave the machine on alone and coming back to it, the sound completely degrades and the OS response completely slows down to a crawl. It is especially prominent if I go to something like youtube and watch a video. the whole thing sputters and stutters and sounds horrible and the os slows to a crawl.
however, if I pause the video, until it's fully loaded, THEN play it, all is well, and my OS goes back to full speed...
but the longer I leave my PC on the WORSE it gets. if I leave it overnight, and come back in the morning, the result is horrible. I have an audio alert to notify me if I have email. normally it just does a quick 'beeep-booop, taking about a quarter of a second' as it flashes the message in the corner. If i leave the machine on over night, the next morning the message will go 'b-e-e-e-e-e-e-e-e-e-e-e-e-p-p-p-p-p-p b-b-b-b-o-o-o-o-o-o-p-p-p-p-' and takes about 5 seconds to complete the notification!
At this point, if I try to restart the computer, or shut it down from the start menu, it does nothing. I go to start select restart, nothing. I go to start, select shutdown, nothing. I have to physically hold down the power button and kill the computer!
I've updated to all the latest drivers for all my components straight of the h-p site. I even tried upgrading my nvidia drivers to the latest from nvidia.com. that didn't work so I reverted back to the h-p ones (from LAST YEAR by the way, can we get an UPDATE!)
so please, tell me WHAT GIVES! In addition to using my computer for daily activities, I also produce music on it. And if I use my pc for more than 2 hours, and I want to work on music, I have to reboot or suffer as my computer completely locks up.
PS. this thing says I cant make a word using the letters h and p... is this a JOKE?!?!?!?!?!?!

sorry about my tone, I don't realize how I sound when I'm typing, though I do think it's ridiculous that a forum about h-p doesn't allow you SAY h-p
anyway, I'm still at a loss for what to do, and it just occured to me that this may not be the place to get official help. are there h-p people here? or should I be contacting support? I have a feeling all they're going to tell me is to update the drivers...

L2TP Remote Access disconnects after a few hours.

Have a few users on Vista/7 using Windows L2TP to connect to our ASA5510. It is reported that after a few hours the connection drops. From what I have seen this can be anywhere around 5-6 hours. Of course my connection will drop after an amount of time has passed and no traffic has passed the tunnel. But the users are adament that this drops during large transfers; i.e. not a timeout issue.
Before I spend anymore time on this I just want to know if this is normal behavior for a remote access L2TP using Windows to disconnect on it's own after this amount of time. Never had a reason myself to remain connected that long, and when I did I used a site 2 site tunnel.

Below is a sample log of the time when disconnects occur, I highlighted in bold the problem area.
vpn-7-715046: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, constructing IPSec SA payload
vpn-7-715046: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, constructing IPSec nonce payload
vpn-7-715001: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, constructing proxy ID
vpn-7-713906: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, Transmitting Proxy Id: Remote host: 76.17.XX.XX Protocol 17 Port 0 Local host: 216.XX.XXX.XXX Protocol 17 Port 1701
vpn-7-715046: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, constructing NAT-Original-Address payload
vpn-7-713171: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, NAT-Traversal sending NAT-Original-Address payload
vpn-7-715046: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, constructing qm hash payload
vpn-7-714005: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, IKE Responder sending 2nd QM pkt: msg id = 00000017
vpn-7-713236: IP = 76.17.XX.XX, IKE_DECODE SENDING Message (msgid=17) with payloads : HDR + HASH (8) + SA (1) + NONCE (10) + ID (5) + ID (5) + NAT-OA (131) + NONE (0) total length : 172
vpn-7-713236: IP = 76.17.XX.XX, IKE_DECODE RECEIVED Message (msgid=958052a1) with payloads : HDR + HASH (8) + DELETE (12) + NONE (0) total length : 68
vpn-7-715047: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, processing hash payload
vpn-7-713906: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, processing delete
vpn-7-713170: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, IKE Received delete for rekeyed centry IKE peer: 76.17.XX.XX, centry addr: ad03bb38, msgid: 0x00000016
vpn-7-713906: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, L2TP/IPSec: Ignoring delete to a rekeyed centry (msgid=16)
vpn-7-713236: IP = 76.17.XX.XX, IKE_DECODE RECEIVED Message (msgid=17) with payloads : HDR + HASH (8) + NONE (0) total length : 52
vpn-7-715047: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, processing hash payload
vpn-7-713906: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, loading all IPSEC SAs
vpn-7-715001: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, Generating Quick Mode Key!
vpn-7-715001: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, Generating Quick Mode Key!
vpn-5-713049: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, Security negotiation complete for User (sam5510) Responder, Inbound SPI = 0xc8ed80c2, Outbound SPI = 0xe007e1fd
vpn-6-602303: IPSEC: An outbound remote access SA (SPI= 0xE007E1FD) between 216.XX.XXX.XXX and 76.17.XX.XX (user= sam5510) has been created.
vpn-7-715007: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, IKE got a KEY_ADD msg for SA: SPI = 0xe007e1fd
vpn-6-602303: IPSEC: An inbound remote access SA (SPI= 0xC8ED80C2) between 216.XX.XXX.XXX and 76.17.XX.XX (user= sam5510) has been created.
vpn-7-715077: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, Pitcher: received KEY_UPDATE, spi 0xc8ed80c2
vpn-7-715080: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, Starting P2 rekey timer: 3420 seconds.
vpn-5-713120: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, PHASE 2 COMPLETED (msgid=00000017)
vpn-7-713906: IKEQM_Active() Add L2TP classification rules: ip <76.17.XX.XX> mask <0xFFFFFFFF> port <4500>
vpn-7-715077: Pitcher: received KEY_SA_ACTIVE, spi 0xc8ed80c2
vpn-7-713906: KEY_SA_ACTIVE old rekey centry found with new spi 0xc8ed80c2
vpn-7-713906: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, sending delete/delete with reason message
vpn-7-715046: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, constructing blank hash payload
vpn-7-715046: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, constructing IPSec delete payload
vpn-7-715046: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, constructing qm hash payload
vpn-7-713236: IP = 76.17.XX.XX, IKE_DECODE SENDING Message (msgid=d84b3b70) with payloads : HDR + HASH (8) + DELETE (12) + NONE (0) total length : 68
vpn-7-713906: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, Active unit activates new SA for remote peer 76.17.XX.XX.
vpn-7-715009: Group = DefaultRAGroup, Username = sam5510, IP = 76.17.XX.XX, IKE Deleting SA: Remote Proxy 76.17.XX.XX, Local Proxy 216.XX.XXX.XXX
vpn-6-602304: IPSEC: An outbound remote access SA (SPI= 0xFD65F940) between 216.XX.XXX.XXX and 76.17.XX.XX (user= sam5510) has been deleted.
vpn-6-602304: IPSEC: An inbound remote access SA (SPI= 0xB2891595) between 216.XX.XXX.XXX and 76.17.XX.XX (user= sam5510) has been deleted.
vpn-7-715077: Pitcher: received key delete msg, spi 0xb2891595
vpn-4-713903: IKE Receiver: Runt ISAKMP packet discarded on Port 4500 from 76.17.XX.XX:4500

System becomes unusable after a few hours?

Hey archers,
I've been on arch for about 2 months now and didn't start having problems until maybe 3 weeks ago. After a few hours of use, everything will completely (and suddenly) become really unresponsive: even an uncached ls or man takes upwards of 15-30 seconds. Using strace, I saw the commands were stalling on IO operations (getdent64 for example), so I came to suspect my disk. The odd thing is, it completely resolves itself upon reboot, at least until I leave the computer on for a few more hours.
About my disk: it's a Crucial 64GB SSD, / and /home are mounted with noatime and both partitions are at about 65% capacity. I profiled the disk using dd before and after reboot the most recent time it became unresponsive:
Before power cycle:
andy@vulpes ~ $ dd if=/dev/zero of=temp bs=1M count=256
256+0 records in
256+0 records out
268435456 bytes (268 MB) copied, 214.902 s, 1.2 MB/s
andy@vulpes ~ $ sudo -i
Password:
[root@vulpes ~]# echo 3 > /proc/sys/vm/drop_caches
[root@vulpes ~]# logout
andy@vulpes ~ $ dd if=temp of=/dev/null bs=1M count=256
256+0 records in
256+0 records out
268435456 bytes (268 MB) copied, 426.4 s, 630 kB/s
After power cycle:
andy@vulpes ~ $ dd if=/dev/zero of=temp bs=1M count=256
256+0 records in
256+0 records out
268435456 bytes (268 MB) copied, 3.01267 s, 89.1 MB/s
andy@vulpes ~ $ sudo -i
[root@vulpes ~]# echo 3 > /proc/sys/vm/drop_caches
[root@vulpes ~]# logout
andy@vulpes ~ $ dd if=temp of=/dev/null bs=1M count=256
256+0 records in
256+0 records out
268435456 bytes (268 MB) copied, 1.22105 s, 220 MB/s
Notice the magnitude difference in throughput speeds (Read 630 kB/s vs. 220 MB/s, Write: 1.2 MB/s vs. 89.1 MB/s), and this doesn't even really cover the disk latency I'm seeing.
Anyone seen anything like this, or have any ideas on how to fix it/debug it more? The fact that it fixes itself after power cycle makes me think it isn't the disk itself, but who knows: a power cycle cycles the disk to some extent too (remount, clear caches, etc.). My other thought is that it might be a kernel upgrade, but I don't remember if this started happening after I upgraded my kernel or not. If it matters, I started using Gnome 3 about a week before this started happening. I don't have much linux profiling-fu, so any help would be appreciated.
Thanks!

Scars wrote:Have you tried running the fsck for your filesystems?
I ran a fsck -n and it showed I had errors so I ran shutdown -Fr now to force a check... three times. Most of the errors have been fixed, but fsck is still reporting errors:
andy@vulpes ~ $ sudo fsck -n
Password:
fsck from util-linux 2.19
e2fsck 1.41.14 (22-Dec-2010)
Warning! /dev/sda3 is mounted.
Warning: skipping journal recovery because doing a read-only filesystem check.
/dev/sda3 contains a file system with errors, check forced.
Pass 1: Checking inodes, blocks, and sizes
Deleted inode 1414483 has zero dtime. Fix? no
Inodes that were part of a corrupted orphan linked list found. Fix? no
Inode 1414512 was part of the orphaned inode list. IGNORED.
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
Block bitmap differences: -5676745 -5681578
Fix? no
Free blocks count wrong (2458077, counted=2457987).
Fix? no
Inode bitmap differences: -1414483 -1414512
Fix? no
Free inodes count wrong (1302486, counted=1302456).
Fix? no
/dev/sda3: ********** WARNING: Filesystem still has errors **********
/dev/sda3: 300010/1602496 files (1.5% non-contiguous), 3943825/6401902 blocks
Could the filesystem errors actually cause this, or are the errors just another symptom of a bad disk?
Last edited by rykki (2011-05-10 05:12:43)

HT5085 I'm a laptop DJ using virtual DJ. My tracks cary from 128 to 320 kbps. So i decided to purchase iTunes Match. After a few hours of matching my library from iTunes I've still got track 128kbps. I can't seem to get iCloud either.

I'm a laptop DJ using virtual DJ. My tracks cary from 128 to 320 kbps. So i decided to purchase iTunes Match. After a few hours of matching my library from iTunes I've still got track 128kbps. I can't seem to get iCloud either.

Match does not change anything in your library. To get the new (uograded) copy for songs that match, you have to delete the original and download the matched copy.
See more info here: http://support.apple.com/kb/HT1711

A few thoughts and experiences after a few hours using my new ThinkPad E440 with Win 8.1

After waiting 36 days for my new ThinkPad to arrive, I guess I'm just "eh" about it after using it some. Here are some of my thoughts, opinions, and experiences I've had after using it for a few hours... Hope this helps other people.
I should not be surprised because I read all the reviews, but the touch pad really sucks. I hate everything about it, the way it clicks - it's so loud and clunky! - and it's insensitivity (and I adjusted this to be more sensitive). Thank goodness for the track point. I love that thing.
The touchscreen stopped working after a few hours of use. After I rebooted it came back. Is this a bad omen? Or did I inadvertantly turn it off? Is that even possible? I am new to Windows 8 so anything is possible.
The touch screen, when it's working, is not very responsive. It's MUCH LESS responsive than my Samsung Galaxy Note 2 Android phone or my LG G Pad 8.3 tablet. This is very disappointing.
I ran the hardware scan that is in the Lenovo Solution Center and got a warning under the category "Local Connection Test". I looked at the list of System Events and it's very long. The first application error event name is MpTelemetry. Response is "Not available". The next one is "PnPRequestAdditionalSoftware". Response is "Not available". And the list goes on and on and on for pages. I have no idea what to do about this or what it means.
Also in the Lenovo Solution Center, under Software, there is a Critical Alert that says I never updated Windows. But I did when it prompted me to while it was first booting up and it was updating and installing things. Where it says "To update your operating system, you must run Windows Update", I click on the Launch button and it takes me to Windows Update where it says No Updates are Available. Go figure. It also says there have been 9 Windows updates made to the computer. I guess I'll have to just always ignore that Critical Alert.
In the system tray, it says "ThinkPad OneLink Dock Detached!". I don't have a dock... So, yes, that's true, it is detached. I'll have to hide that one.
I realize there is a Lenovo Recovery Partition on the hard drive but I would really like to create a set of recovery disks before I start customizing this thing, installing apps, and moving my files over. I can't find anything that tells me how to do it. Under the control panel, there is the Recovery icon. The only choice there for creating recovery media is to create a Recovery Drive, not disks. I'll post a separate item to get information on this.
On the positive side, I have had it in my lap the whole time and it's not gotten too hot for my legs. That's a big improvement on my old Toshiba Satellite Pro.
This locating the Fn key to the left of the CTRL key decision must have been made by someone smoking crack. Why would anyone in their right mind want to do this? We've had the CTRL key on the outer left edge like, FOREVER, why move it now?? This will be something that will take me a long time to adjust to - if I ever do. I use the CTRL a lot for cutting, pasting, and formatting things in Excel and Word. It's going to be a battle. I wonder if any software exists that allows you to redefine the keys? Speaking of location of keys, I keep hitting the Page Down key when I want the Page Up key. I'm used to the Page Up key being above the Page Down key instead of to the left.
After being told here in the forum that the fingerprint reader was not an option in the US I am pleasantly surprised to see one on my new ThinkPad.
I use the right-click on my mouse often. For example, to open a link in a new tab instead of switching to the new URL. For some reason, when I click on the right part of the touch pad when the mouse is located over a link, it just opens the new URL instead of giving me options for opening the URL. I'll have to figure this out.
So anyway, I guess that's more than a few things... hope this is useful to someone...

You can change FN and CTRL key in the BIOS

I am trying to do a full Time Machine Backup to a new external disk. The backup starts, and it says "Time remaining about 4 days." That seems like a very long time, but the real problem is that the computer "logs off" after a few hours, and the b.u. stops

I am trying to do a full Time Machine Backup to a new external disk. The backup starts, and it says "Time remaining about 4 days." That seems like a very long time, but the real problem is that the computer "logs off" after a few hours, and the backup stops. The system preferences are set to "Never" for Computer sleep and Display sleep. The computer does not ordinarily log off automatically, but it has done this twice since I started the Time Machine backup.

If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the word "Starting" (without the quotes) in the String Matching text field. You should now see log messages with the words "Starting * backup," where * represents any of the words "automatic," "manual," or "standard." Note the timestamp of the last such message. Clear the text field and scroll back in the log to that time. Select the messages timestamped from then until the end of the backup, or the end of the log if that's not clear. Copy them (command-C) to the Clipboard. Paste (command-V) into a reply to this message.
If all you see are messages that contain the word "Starting," you didn't clear the search box.
If there are runs of repeated messages, post only one example of each. Don't post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Some personal information, such as the names of your files, may be included — anonymize before posting.

After a few hours of inactivity , my screen goes white with a flashing file folder in the centre with a question mark in the centre of said folder. at this point i can only unplug the computer for it to reboot properly, then it is fine till the next go..

After a few hours of inactivity, I return to find a white screen with a file folder in the center of the screen with a ? mark in the centre of said folder and both are flashing...am i compromised?

No
Solution may be found if you search in the "More Like This" section over in the right column.

Just installed thunderbird on new computer having used it for years on old laptop. Why do my mails disappear from my inbox after a few hours. Can I change this?

I had Windows Xp on the old laptop and used Thunderbird for ages, but have now installed the same version of Thunderbird on a new laptop with windows 8.1 and it is quite different. How can I stop it removing the contents of my inbox after a few hours. Its very frustrating when you dont want to reply to an e mail immediately but lose it overnight!

http://kb.mozillazine.org/Disappearing_mail

Mac book pro mid 2009 shuts down after a few hour then will only boot after waiting and pressing power button numerous times. I am running mountain lion with most recent updates.

Mac book pro mid 2009 shuts down after a few hour of use and then is very difficult to reboot. Sometimes I have to wait hours, sometimes I have to repeatedly press the power button and then it will slowly start a little longer each press untill it completely boots. It has done this three times know. Each time I was watching a video.

Try running the Apple Hardware Test - sounds as if you've hardware issues.
Clinton

Macbook Air 13" Camera stops working after a few hours. Needs Restart to be functioning again. How do I fix this?

Hello!
The camera stops working. Not detected by any program (Facetime, Skype, Hangouts, Zoom). This happens usually after a few hours of work or after the computer sleeps. To make the webcam function again I need to restart.
Any suggestions?

Why does that seem likely to be a hardware issue? How did you come to that conclusion? Do you know something about this issue that indicates that? (I realise that this might sound short and rude - I am not trying to be rude here - just to understand) My thought is that conventional troubleshooting would say that this is a software issue because it is fixed with a restart.
I also have this problem. The camera quits working after some time - I have not been able to make it stop working. Sometimes it is after I suspend the computer (close the lid) other times it still works.
All I know is that intermittently my camera stops working and it is a big pain to have to reboot whenever I am going have a video chat.
Anyone got any solutions, I'm not covered by applecare so would rather try and fix it myself if possible?

When I make my computer to sleep after a few hour it will light up again and say that The mac have a problem need to be shut down

I don't know why wne I put my mac to sleep it will light up it self after a few hour and say that the mac have a problem needs to be shut down, does anyone know why?

Sounds like it's experiencing a kernel panic. Post the latest report. See
About kernel panics,
Technical Note TN2063: Understanding and Debugging Kernel Panics,
Mac OS X Kernel Panic FAQ,
Resolving Kernel Panics, and
Tutorial: Avoiding and eliminating Kernel panics for more details.

Labview Program always crashs after a few hour' work

My Labview Program always crashs after a few hour' work. The error report is:
#Date: 2014年7月30日 4:27:27
#OSName: Windows 7 Ultimate
#OSVers: 6.1
#OSBuild: 7600
#AppName:
#Version: 12.0 32-bit
#AppKind: AppLib
#AppModDate: 07/29/2014 20:13 GMT
#LabVIEW Base Address: 0x30000000
<DEBUG_OUTPUT>
2014/7/30 8:34:11.006
DAbort 0xF50EFD7B:
c:\builds\penguin\labview\components\mgcore\trunk\12.0\source\MemoryManager.cpp(1104) : DAbort 0xF50EFD7B:
minidump id: 6ebe0400-78d2-41e3-b2fd-858c21e3567b
$Id: //labview/components/mgcore/trunk/12.0/source/MemoryManager.cpp#13 $
</DEBUG_OUTPUT>
0x30076B23 - lvrt <unknown> + 0
0x307D1F90 - lvrt <unknown> + 0
0x30605C66 - lvrt <unknown> + 0
0x6C42A045 - nivissvc <unknown> + 0
0x075A1F00 - nivision <unknown> + 0
0x03B0577A - <unknown> <unknown> + 0
0xE5BA0800 - <unknown> <unknown> + 0
Who knows what had happened? Thank you for your help.

Thank you for your reply.
I don't build array continuously. I just build a few queues. I am sorry the program is too large to show it to you. I have read the dump file. It seems like memory overflow. Do you think so? But it seems like there is no chance for memory overflow in Labview. The dump file is as below:
Microsoft (R) Windows Debugger Version 6.3.9600.17029 X86
Copyright (c) Microsoft Corporation. All rights reserved.
Loading Dump File [D:\LabVIEW Data\LVInternalReports\1.0.0.1\51437f73-aab6-4097-b7e1-3fee8a74e4dd\6ebe0400-78d2-41e3-b2fd-858c21e3567b.dmp]
User Mini Dump File: Only registers, stack and portions of memory are available
************* Symbol Path validation summary **************
Response Time (ms) Location
OK C:\Program Files (x86)\Symbols
Symbol search path is: C:\Program Files (x86)\Symbols
Executable search path is:
Windows 7 Version 7600 MP (4 procs) Free x86 compatible
Product: WinNt, suite: SingleUserTS
Machine Name:
Debug session time: Wed Jul 30 08:34:10.000 2014 (UTC + 8:00)
System Uptime: not available
Process Uptime: 0 days 4:06:44.000
This dump file has an exception of interest stored in it.
The stored exception information can be accessed via .ecxr.
(dfc.4b8): Unknown exception - code 00000002 (first/second chance not available)
*** WARNING: Unable to verify timestamp for ntdll.dll
*** ERROR: Module load completed but symbols could not be loaded for ntdll.dll
*** WARNING: Unable to verify timestamp for kernel32.dll
*** ERROR: Module load completed but symbols could not be loaded for kernel32.dll
eax=13dbec20 ebx=13dbe550 ecx=00000008 edx=00000008 esi=00000003 edi=13dbe570
eip=77b564f4 esp=13dbe500 ebp=13dbe59c iopl=0 nv up ei pl zr na pe nc
cs=001b ss=0023 ds=0023 es=0023 fs=003b gs=0000 efl=00000246
ntdll+0x464f4:
77b564f4 c3 ret

Emails deleting themselves on Blackberry Pearl after a few hours

Similar Messages

Maybe you are looking for