EMU 1212m installation problems! Help needed!

Hello everyone. Hopefully someone can help me out, getting my 1212m back to working.
A month ago, I bought a new computer and I put a EMU 1212m into it. It worked fine, until some other audio devices had bad drivers and made windows crash so many times, I decided to format my hard disk and install XP over again. Well, that worked out fine, computer is running very smoothly but I cant install my 1212m anymore. Windows does find new hardware, which it names "multimedia-audiocontroller, pci slot xx, etc" in the device manager. When I start the EMU setup from the original CD, it says "setup has not detected any supported hardware on your computer" and it closes down right away.
I already tried this:
- multiple installation CD's
- multiple EMU drivers (internet, etc)
- chancing PCI slots
- disabling on-board sound via Bios
- cleaning up registery settings from earlier installation attemps.
- manually select the drivers on the installation CD. It installes the drivers and then Windows says: this device will not start.
I can try whatever I want, but the message keeps on showing up everytime I start a setup. I don't know which actions to take next, so I desperately need some advice here.
any help will be much appreciated!
thanks,
Hugo

I just bought a 1212M and have had similar problems. I assumed the website drivers would be newer than those on the accompanying CD as is the case with most products -- WRONG! I got the same symptoms you describe with the internet drivers, only when I used the CD did it work -- and to my amazement, the CD drivers seems to be newer than the internet downloads (excluding the 2.0 beta drivers of course).
Another complication I had was that I left my perfectly working X-Fi in the computer while installing the 1212M .... the drivers seem to confuse the two cards, which doesn't help. In fairness, the Emu documentation does warn about this, however I eventually got both to work together. If you have a second soundcard in the same computer, even one built into the motherboard, disable it and see if that helps. The Creative (SoundBlaster) drivers are notoriously hard to uninstall cleanly, so if necessary follow Martin Walker's excellent advice over at Sound On Sound (http://www.soundonsound.com/sos/mar0...pcmusician.htm).

Similar Messages

Oracle forms installation - some help need

I am trying to install Oracle forms - but get the follwing message:
Checking swap space: 576 MB available, 1535 MB required. Failed <<<<
Some requirement checks failed. You must fulfill these requirements before
continuing with the installation,at which time they will be rechecked.
Continue? (y/n) [n]
actually - I have no choice to choose y and try what's going on - so - is this means that I shoul add some 1.5 GB of RAM to my computer? (I have already 700MB, only 300 of them are used)? I am using WinXP, free HD is above 3.5 GB, 2.4GHz processor.
Can I try to find some workaround - e.g. simply try to copy jar's from 'stage' (direcotry in installation disk) in Oracle application server's lib directory (where it is in Oracle_Home directory?)?
Any experience with installing Oracle forms?
This was trying to run setup.exe, but when I am trying to run wsf.exe - I get:
SEVERE: Unable to locate the MDAC Update Status registry key value, probably because the installation was aborted.
MDAC possibly stands for Microsoft Data Access Components? If so - where is problem - I can run a lot of DB servers, including Oracle server itself normally?
BTW - is there any free service available for Oracle Forms skills development (e.g. as for Oracle SQL the Intel test drive is available?)
user454720

OK - now I increased the max limit of my page file and now I achieved this:
Starting Oracle Universal Installer...
Checking installer requirements...
Checking operating system version: must be 5.0, 5.1 or 5.2 . Actual 5.1
Passed
Checking monitor: must be configured to display at least 256 colors . Actual
4294967296 Passed
Checking swap space: must be greater than 1535 MB . Actual 1600MB Passed
Checking Temp space: must be greater than 150 MB . Actual 1942 MB Passed
All installer requirements met.
Preparing to launch Oracle Universal Installer from C:\DOCUME~1\ADMINI~1\LOCALS
~1\Temp\OraInstall2006-03-18_01-57-43PM. Please wait ...
however - after this I receive the standard messgae:
'setup.exe has encountered a problem and need to close. we are sorry for the inconvenience..... Please tell Microsoft about thsi problem'
actually - I have little ideas what to do further - maybe I should look for other Oracle Installer version? I am using:
Oracle Universal Installer version: 10.1.0.2.0
and I am trying to install
Oracle Deveoper Suite: 10.1.2.0.2 (so - a bit higher)
I can run OUI without any problems, my Default JRE is 1.5_1 - so - all seems to be OK?
Please - if any idea - help me :))
Thanks in advance!

Tiger Installation Problems ~help please~

I have the DVD that says:
MAC OS X TIGER
Includes Xcode 2
CPU Drop In DVD
i wiped my hard drive on my G4 dual 450 (using disk utility)
i put the DVD in HD and turned the computer on
i clicked on the 'continue & agree' buttons and the next screen
it says that i needed to have 10.3 in order to install 10.4
ummmm why?
please help. need to get up and running for work..... DOH!
thanks to everyone
G4 dual 450 1gb ram / 80gb hd / 30gb hd

"DOH" is right! "Wiping" your hd before even making a back-up is not the most highly recommended method of proceeding with an upgrade or update! Nevertheless, there you are and you need help, not a sermon...right? So, do you have the disks that came with your computer (or whatever version you have other than the 10.4 disks)? If so, you can re-install whatever version of MacOS you started with. The disks you are attempting to use for the upgrade to 10.4...are they gray by any chance? If so, they are "OEM" versions and will not allow you complete the install on any computer other than the one they shipped with. You need to buy the retail (full) version of 10.4. Then you can either perform an Upgrade or a "clean Install" as you wish.

Driver Installation Error, help need

Hi all,
I just downloaded the newest drivers for my Soundblaster Audigy ZS 2, WinVista 32 bit.
When I try to install, everything goes fine till an error occured (see screen)
Screen: http://img5.imageshack.us/img5/660/errordj0.jpg
Something with the APOIM installer, any help would greatly be appreciated. I already searched the FAQ and known issues etc.
Thx in advance, xGj.

Hey I had that same error but?I resolved it.. First download winrar, www.rarlabs.com, second install it and then right click that exe for your driver and click on extract all to that specific folder, for vista the default is downloads, and then just extract and run the setup.exe in that folder and not from the program that you have downloaded from the creative driver website. Worked for me it should work for ya also, Good Luck...

Lenovo Tablet 2 Installation Problems - Help would be GREATLY appreciated as Lenovo WILL NOT HELP.

Hi everyone. I've been pulling my hair out with this and I'm just about at my breaking point after 15 some hours of messing with this but I thought I would give it one last shot.
I have a Lenovo Tablet 2 that originally came with Windows 8 and later was upgraded via the store to 8.1. When I went to do a complete format and re-install it asked me for media. This product does not come with media. I figured the worst thing was that I would have to go the long way and install Windows without the recovery partition and reinstall all the drivers manually. Boy was I wrong. I booted to my UEFI enabled USB Windows 8.1 installer stick which was created using the new Mediacreationtool that Microsoft released to make either an ISO or USB stick. Knowing this is UEFI only (more on that later), I downloaded the ISO and created the USB stick using RUFUS. That booted fine and i blew away all the partitions and started the install. Install goes fine until the very last step and says "windows could not update the computer's boot configuration". The end. Game over. I can't get past this. I've tried the following:
1. Created a DaRT disc and did a complete clean of the drive
2. tried a Windows 10 Disc - same thing
3. Tried to edit the BCD using bcdedit command (more on that later) and nothing.
I've probably done a half dozen other random things and I'm still back at the same position here. The big issue with this device is that it is 32BIT UEFI only BIOS. Terrible to work with because everything considers UEFI to be a 64bit only function so there isn't much that I can even get to boot.
Back to BCD Edit. Anything I try to do just gives me the result of "The boot configuration data store could not be opened. The volume for a file has been externally altered so that the opened file is no longer valid.". I cannot createstore, edit the store, or do anything with it.
Again, i'm at wits end here. I contacted Lenovo and it's out of warranty so they told me to pound sand. I asked them just for a recovery media which every device should come with and **bleep** the OEMs for not doing that aymore and they told me to go pound the same mound of sand. Help would be GREATLY appreciated. This thing is slowly walking it's way to the trash can. It's a mental thing at this point now and I have to get this working. Please help. Thank you.

Yup, we had to do a clean install and same issue nothing will work after a stock clean install of windows 8.1 pro or 8 pro or 8n or 8.1n or any 8-1 for that mater we tried 6 loads with same issue on the IO file for the atom CPU Chipset...When you try to download the drivers from there site for the IO drivers and install it stop there and does not work with there Leveno drivers and if out of warentee they do not even care if there own leveno drivers for 8.1 do not work with 8.1 for the IO drivers on Leveno download site...When we called Microsoft they even sugest getting another tablet from another better supported MFG. WOW I own 4 Leveno products and almost got a new tablet a few nights ago but will not get any more leveno products till I research the issues they have with stock roms! Reinstalls should be much more friendly and updates should be listed correctly on the web site...They do not say it is a ported win8.0 frankinstien windows load when you buy their tablet. But they should say it is kinda windows 8.0 almost and that only there usb key will let you reaload the hack-up windows the tablet needs.

Installation Problem-Internet needs to be closed

When I try to use Flash Player, it tells me it's not instaled. I have installed Flash Player numerous times, the one problem seems to be when it installs it says to close Internet Explorer (I do ) but it still doesn't work. I can't run any video on my desktop. Any help/assistance will be greatly appreciated. Thanks.

I am continually have the same exact issue, PLUS, it says that I have loaded Flash; however, it does not show as being loaded at all. HELP!!!!!!!!!!!!!!!!!!!!!

Labview 2009 SP1 Installer build help needed

Hello,
First time posting here. I have a rather large project that I recently converted from Labview 7.0 to 9.0. I am able to build an executable and it starts up Ok but I don't know for sure if it works. Since I couldn't build an installer, I copied the folder containing the .exe onto the targeted machine and installed Labview Run-time Engine 2009 SP1. The executable then complains that it needs the full development version to work. I am not too worry about this part at the moment, but if you have any pointers, please go ahead and post them.
Ok, I have gone through a lot of posts on building and installer but it seems the one post that has something similar to what I experienced didn't get an answer. Here's the Build Errors from the pop-up dialog:
CDK_Item_OnDoProperties.vi.ProxyCaller >> CDK_Item_OnDoProperties.vi >> CDK_InstallerConfiguration_Editor.vi >> CDK_Build_Invoke.vi >> CDK_Engine_Main.vi >> CDK_Engine_BuildDevPart.vi >> NI_MDF.lvlib:MDFBuildDevPart_SetOtherProperties.vi
Loading product deployment information
Loading product deployment information
Loading product deployment information
Loading product deployment information
Adding files to installer
*** Error: An internal tool or library returned an error. (Error code -21)
*** End Error Report
*** Error: Windows SDK function returned an error. (Error code -12)
*** End Error Report
The build log file has slightly more info:
    [LOG ON] Mon May 31 20:55:07 2010
<<<MDFConfig_SetDeveloperLanguage>>> Language id: 9
<<<MDFConfig_SetDistributionLanguage>>> Language id: 9
<<<MDFConfig_SetBuildDir>>> Build directory: C:\HardwareTest\XXX\Release\Installers\Lab Test Suite 4.2.9 Installer - XXX
<<<MDFConfig_SetBuildMode>>> Build mode: 1
    [NMDK BEGIN] Mon May 31 20:55:07 2010
     Building developer part
> Adding files to installer
<<<MDFBuildDevPart_SetFileNames>>>
<<<MDFBuildDevPart_SetDefaultInstallDir>>>
<<<MDFBuildDevPart_SetUpgradeInfo>>>
<<<MDFBuildDevPart_SetOtherProperties>>>
>
> **************
> *** Error: An internal tool or library returned an error. (Error code -21)
Error in MDF API function: _MDFBuildDevPart_SetOtherProperties
nmdkSetInformationalProperties returned error code 26024
> *** End Error Report
> **************
>
Adding product dependencies to developer part
>
> **************
> *** Error: Windows SDK function returned an error. (Error code -12)
Closing dist kit
***** About to begin MAXImportConfig:oMAXPartModifications...
No MAX import files specified - nothing to do - returning.
Error in MDF API function: _MDFBuildDevPart_Close
Error in MDF::BuildDeveloperPart::Close.
ERROR: Caught MSI Exception:
<Unable to format error record.>
MSI error code: 6
> *** End Error Report
> **************
>
    [LOG OFF] Mon May 31 20:55:07 2010
    [MDF END] Mon May 31 20:55:07 2010
     Closing MDF.
I realize that I should post my project file but I can't do that until tomorrow. From those 2 errors, can you tell me what the installer builder is looking for? I have gone through all my dependencies and they look Ok at the moment.
Thanks for you time.

Hi Celeb,
I had to help out on another project and finally only getting back to looking at this issue yesterday. As you suggested, I went ahead and created a new project and created new build specifications (exe and installer). I was able to properly build both items but won't be able to check out the executable til later this week.
I noticed one thing about the project that Labview produced after converting the old *.bld file to a project file.  With the converted project, Labview adds unexpected installer destination folders into WindowsFolder in the Installer/Source Files/Destination View. I thought I deleted them before but they seem to make it back (kinda hazy about this at this point).  My actual installer folder should only go into the WindowsVolume folder. Anyway, on the new build spec, since I don't manually add the installer folder into the WindowsFolder, nothing get populated there and the installer is able to build properly. This might have been the cause of my inability to build an installer with the converted project/build specs.
I hope NI could add in more details into the build error messages. As it is, it's really difficult to know why a build failed because there's no details in those messages.
Thanks again,
T.

Linked lists problem -- help needed

Hello again. I've got yet another problem in my C++ course that stems from my use of a Mac instead of Windows. I'm going to install Parallels so I can get Windows on my MacBook and install Visual Studio this week so that I don't have to deal with these discrepancies anymore, but in the meanwhile, I'm having a problem here that I don't know how to resolve. To be clear, I've spent a lot of time trying to work this out myself, so I'm not just throwing this up here to have you guys do the work for me -- I'm really stuck here, and am coming here as a last resort, so I'll be very, very appreciative for any help that anyone can offer.
In my C++ course, we are on a chapter about linked lists, and the professor has given us a template to make the linked lists work. It comes in three files (a header, a source file, and a main source file). I've made some adjustments -- the original files the professor provided brought up 36 errors and a handful of warnings, but I altered the #include directives and got it down to 2 errors. The problematic part of the code (the part that contains the two errors) is in one of the function definitions, print_list(), in the source file. That function definition is shown below, and I've marked the two statements that have the errors using comments that say exactly what the errors say in my Xcode window under those two statements. If you want to see the entire template, I've pasted the full code from all three files at the bottom of this post, but for now, here is the function definition (in the source file) that contains the part of the code with the errors:
void LinkedList::printlist( )
// good for only a few nodes in a list
if(isEmpty() == 1)
cout << "No nodes to display" << endl;
return;
for(CURSOR = FRONT_ptr; CURSOR; CURSOR = CURSOR-> link)
{ cout << setw(8) << CURSOR->name; } cout << endl; // error: 'setw' was not declared in this scope
for(CURSOR = FRONT_ptr; CURSOR; CURSOR = CURSOR-> link)
{ cout << setw(8) << CURSOR->test_grade; } cout << endl; // error: 'setw' was not declared in this scope
As you can see, the problem is with the two statements that contain the 'setw' function. Can anyone help me figure out how to get this template working and get by these two errors? I don't know enough about linked lists to know what I can and can't mess with here to get it working. The professor recommended that I try using 'printf' instead of 'cout' for those two statements, but I don't know how to achieve the same effect (how to do whatever 'setw' does) using 'printf'. Can anyone please help me get this template working? Thank you very, very much.
For reference, here is the full code from all three files that make up the template:
linkedlist.h (header file):
#ifndef LINKED_LINKED_H
#define LINKED_LINKED_H
struct NODE
string name;
int test_grade;
NODE * link;
class Linked_List
public:
Linked_List();
void insert(string n, int score);
void remove(string target);
void print_list();
private:
bool isEmpty();
NODE *FRONT_ptr, *REAR_ptr, *CURSOR, *INSERT, *PREVIOUS_ptr;
#endif
linkedlist.cpp (source file):
#include <iostream>
using namespace std;
#include "linkedlist.h"
LinkedList::LinkedList()
FRONT_ptr = NULL;
REAR_ptr = NULL;
PREVIOUS_ptr = NULL;
CURSOR = NULL;
void Linked_List::insert(string n, int score)
INSERT = new NODE;
if(isEmpty()) // first item in List
// collect information into INSERT NODE
INSERT-> name = n;
// must use strcpy to assign strings
INSERT -> test_grade = score;
INSERT -> link = NULL;
FRONT_ptr = INSERT;
REAR_ptr = INSERT;
else // else what?? When would this happen??
// collect information into INSERT NODE
INSERT-> name = n; // must use strcpy to assign strings
INSERT -> test_grade = score;
REAR_ptr -> link = INSERT;
INSERT -> link = NULL;
REAR_ptr = INSERT;
void LinkedList::printlist( )
// good for only a few nodes in a list
if(isEmpty() == 1)
cout << "No nodes to display" << endl;
return;
for(CURSOR = FRONT_ptr; CURSOR; CURSOR = CURSOR-> link)
{ cout << setw(8) << CURSOR->name; } cout << endl; // error: 'setw' was not declared in this scope
for(CURSOR = FRONT_ptr; CURSOR; CURSOR = CURSOR-> link)
{ cout << setw(8) << CURSOR->test_grade; } cout << endl; // error: 'setw' was not declared in this scope
void Linked_List::remove(string target)
// 3 possible places that NODES can be removed from in the Linked List
// FRONT
// MIDDLE
// REAR
// all 3 condition need to be covered and coded
// use Trasversing to find TARGET
PREVIOUS_ptr = NULL;
for(CURSOR = FRONT_ptr; CURSOR; CURSOR = CURSOR-> link)
if(CURSOR->name == target) // match
{ break; } // function will still continue, CURSOR will
// mark NODE to be removed
else
{ PREVIOUS_ptr = CURSOR; } // PREVIOUS marks what NODE CURSOR is marking
// JUST before CURSOR is about to move to the next NODE
if(CURSOR == NULL) // never found a match
{ return; }
else
// check each condition FRONT, REAR and MIDDLE
if(CURSOR == FRONT_ptr)
// TARGET node was the first in the list
FRONT_ptr = FRONT_ptr -> link; // moves FRONT_ptr up one node
delete CURSOR; // deletes and return NODE back to free memory!!!
return;
}// why no need for PREVIOUS??
else if (CURSOR == REAR_ptr) // TARGET node was the last in the list
{ // will need PREVIOUS for this one
PREVIOUS_ptr -> link = NULL; // since this node will become the last in the list
REAR_ptr = PREVIOUS_ptr; // = REAR_ptr; // moves REAR_ptr into correct position in list
delete CURSOR; // deletes and return NODE back to free memory!!!
return;
else // TARGET node was the middle of the list
{ // will need PREVIOUS also for this one
PREVIOUS_ptr -> link = CURSOR-> link; // moves PREV nodes' link to point where CURSOR nodes' points
delete CURSOR; // deletes and return NODE back to free memory!!!
return;
bool Linked_List::isEmpty()
if ((FRONT_ptr == NULL) && (REAR_ptr == NULL))
{ return true; }
else
{ return false;}
llmain.cpp (main source file):
#include <iostream>
#include <string>
#include <iomanip>
using namespace std;
#include "linkedlist.h"
int main()
Linked_List one;
one.insert("Angela", 261);
one.insert("Jack", 20);
one.insert("Peter", 120);
one.insert("Chris", 270);
one.print_list();
one.remove("Jack");
one.print_list();
one.remove("Angela");
one.print_list();
one.remove("Chris");
one.print_list();
return 0;

setw is the equivalent of the field width value in printf. In your code, the printf version would look like:
printf("%8s", CURSOR->name.c_str());
I much prefer printf over any I/O formatting in C++. See the printf man page for more information. I recommend using Bwana: http://www.bruji.com/bwana/
I do think it is a good idea to verify your code on the platform it will be tested against. That means Visual Studio. However, you don't want to use Visual Studio. As you have found out, it gets people into too many bad habits. Linux is much the same way. Both development platforms are designed to build anything, whether or not it is syntactically correct. Both GNU and Microsoft have a long history of changing the language standards just to suit themselves.
I don't know what level you are in the class, but I have a few tips for you. I'll phrase them so that they answers are a good exercise for the student
* Look into const-correctness.
* You don't need to compare a bool to 1. You can just use bool. Plus, any integer or pointer type has an implicit cast to bool.
* Don't reuse your CURSOR pointer as a temporary index. Create a new pointer inside the for loop.
* In C++, a struct is the same thing as a class, with all of its members public by default. You can create constructors and member functions in a struct.
* Optimize your function arguments. Pass by const reference instead of by copy. You will need to use pass by copy at a later date, but don't worry about that now.
* Look into initializer lists.
* In C++ NULL and 0 are always the same.
* Return the result of an expression instead of true or false. Technically this isn't officially Return Value Optimization, but it is a good habit.
Of course, get it running first, then make it fancy.

Layout Problem, Help Need

I developed one custom Report, which will print on pre print stationary. Really Problem here is when i send to printer it will printer properly on 8/12 By 11 Page, but i don't what is the reason it is not printing on Page after 7 Inch, even i thought i increase layout width it dos't Print after 7 Inch on Page, can i know why it is doing like these, any clue, please let me know.
Report Verions : 6i
Main Section : Width => 8.5
Height => 12.5
Orientation => Portrait
Report Width => 80
Report Height => 90
Your Help Rally appreicate in advance.
Thanks,
Praveen

You may need to contact support and actually show them the report to really solve the problem, but here are a few things to check first:
a) Check the report margins, make sure that they will allow the report body to display past 7".
b) Check that the frames and repeating frames are set to horizontally variable, or expand so that they can grow if required.
Hope this helps,
Danny

Windows 7 Adobe Air Uninstall problem - Help Needed

I can't uninstall Adobe Air from my control panel or manually from the cmd prompt [AdobeAIRInstaller.exe -uninstall] I get an error box that
says that the Adobe Air Installer has stopped working.
Problem signature:
Problem Event Name:    APPCRASH
Application Name:    Adobe AIR Installer.exe
Application Version:    2.7.1.19610
Application Timestamp:    4e3c2b43
Fault Module Name:    mlang.dll
Fault Module Version:    6.1.7600.16385
Fault Module Timestamp:    4a5bda21
Exception Code:    c0000005
Exception Offset:    0000bbff
OS Version:    6.1.7601.2.1.0.256.1
Locale ID:    1033
Additional Information 1:    0a9e
Additional Information 2:    0a9e372d3b4ad19135b953a78882e789
Additional Information 3:    0a9e
Additional Information 4:    0a9e372d3b4ad19135b953a78882e789
Here is my install log:
[2011-08-02:01:11:23] Runtime Installer begin with version 2.7.0.19480 on Windows 7 x86
[2011-08-02:01:11:23] Commandline is: -update "c:\program files (x86)\adobe media player\adobe media player.exe"
[2011-08-02:01:11:23] Installed runtime (1.5.3.9120) located at C:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-02:01:11:23] Installed app (com.adobe.amp.4875E02D9FB21EE389F73B8D1702B320485DF8CE.1) located at c:\program files (x86)\adobe media player\adobe media player.exe
[2011-08-02:01:11:26] Relaunching with elevation
[2011-08-02:01:11:26] Launching subprocess with commandline c:\users\ratliff\appdata\local\temp\air2261.tmp\adobe air installer.exe -ei
[2011-08-02:01:11:28] Runtime Installer begin with version 2.7.0.19480 on Windows 7 x86
[2011-08-02:01:11:28] Commandline is: -stdio \\.\pipe\AIR_5572_0 -ei
[2011-08-02:01:11:28] Installed runtime (1.5.3.9120) located at C:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-02:01:11:28] Starting silent runtime update. Updating runtime from version 1.5.3.9120 to version 2.7.0.19480
[2011-08-02:01:11:28] Installing msi at c:\users\ratliff\appdata\local\temp\air2261.tmp\setup.msi with guid {FDB3B167-F4FA-461D-976F-286304A57B2A}
[2011-08-02:01:11:29] Runtime Installer end with exit code 0
[2011-08-02:01:11:29] Elevated install completed
[2011-08-02:01:11:31] Launching subprocess with commandline c:\program files (x86)\adobe media player\adobe media player.exe
[2011-08-02:01:11:31] Runtime Installer end with exit code 0
[2011-09-06:09:04:13] Runtime Installer begin with version 2.7.1.19610 on Windows 7 x86
[2011-09-06:09:04:13] Commandline is:
[2011-09-06:09:04:13] Installed runtime (2.7.0.19480) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-09-06:09:04:16] Relaunching with elevation
[2011-09-06:09:04:16] Launching subprocess with commandline c:\users\ratliff\appdata\local\temp\aira35e.tmp\adobe air installer.exe -ei
[2011-09-06:09:04:16] Runtime Installer begin with version 2.7.1.19610 on Windows 7 x86
[2011-09-06:09:04:16] Commandline is: -stdio \\.\pipe\AIR_3156_0 -ei
[2011-09-06:09:04:16] Installed runtime (2.7.0.19480) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-09-06:09:04:17] Starting silent runtime update. Updating runtime from version 2.7.0.19480 to version 2.7.1.19610
[2011-09-06:09:04:17] Reinstalling c:\users\ratliff\appdata\local\temp\aira35e.tmp\setup.msi
[2011-09-06:09:04:18] Runtime Installer end with exit code 0
[2011-09-06:09:04:18] Elevated install completed
[2011-09-06:09:04:20] Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -installupdatecheck
[2011-09-06:09:04:20] Runtime Installer end with exit code 0
[2011-09-06:09:04:20] Runtime Installer begin with version 2.7.1.19610 on Windows 7 x86
[2011-09-06:09:04:20] Commandline is: -installupdatecheck
[2011-09-06:09:04:20] Installed runtime (2.7.1.19610) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-09-06:09:04:20] Performing pingback request
[2011-09-06:09:04:21] Pingback request completed with HTTP status 200
[2011-09-06:09:04:21] Starting runtime background update check
[2011-09-06:09:04:21] Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/2.7.1.19610/update
[2011-09-06:09:04:21] Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/2.7.1.19610/update to C:\Users\Ratliff\AppData\Roaming\Adobe\AIR\Updater\Background
[2011-09-06:09:04:21] Runtime update not available
[2011-09-06:09:04:21] Unpackaging cancelled
[2011-09-06:09:04:21] Runtime Installer end with exit code 0
I suspect this is causing a few of my other programs to crash as well.
Please Help!
Jamie

Hi Jamie,
The install log looks fine, but the last entry was September 9th. I suspect the crash is occuring before the new log entries can be made.
Could you please open a new bug report on this over at bugbase.adobe.com? We'll want to get a crash dump so we can try to figure out what might be causing this to happen. You didn't mention what OS you were running, but I found this tech doc on the net that describes how do generate the .dmp file:
Creating Dr. Watson crash dumps
Thanks,
Chris

9i Developer suite login problem. help needed ASAP

i installed oracle 9i developer suite, my problem is i can't login. this is the error ora12560: TNS: oracle adapter error.
or
if i put the hostname it displays a no listener error and closes. i tried to create a listener in net configuration assistant, but i can't see it in services.
i'm using windows XP. and not conneted to any machine.
do i need any changes on my window settings?
please help...
thanks
here is my listener.ora
ABC =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = abc)(PORT = 1521))
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = abc)(PORT = 1521))
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = C:\OraHome)
(PROGRAM = extproc)
tnsnames.ora
TEST.ABC =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = ABC)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = test.ABC)
ORACLE =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = abc)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = oracle)

check your operating system network protocole is TCP/IP is installed if so check is there any problem with these protocoles. this error is encounter generally due operating system network protocoles it is not an oracle error. here is discription.
TNS-12560 TNS:protocol adapter error
Cause: A generic protocol adapter error occurred.
Action: Check addresses used for proper protocol specification. Before reporting this error, look at the error stack and check for lower level transport errors.For further details, turn on tracing and re-execute the operation. Turn off tracing when the operation is complete.

( jrew.exe encounterd problem,help needed )

MY DEARS
I AM FACING A PROBLEM ON MY P4 LAPTOP AND DESKTOP COMPUTOR ON A PRGRAMM ON SURGERY CD ,WHICH ON START UP DIPLAYS MESSAGE ( jrew encountered a problem,needs to close-)
WHAT IS THE SOLUTION .HELP IS APPERECIATED.
MANY REGARDS FOR HELPER.
DR QAMAR

Hi Jamie,
The install log looks fine, but the last entry was September 9th. I suspect the crash is occuring before the new log entries can be made.
Could you please open a new bug report on this over at bugbase.adobe.com? We'll want to get a crash dump so we can try to figure out what might be causing this to happen. You didn't mention what OS you were running, but I found this tech doc on the net that describes how do generate the .dmp file:
Creating Dr. Watson crash dumps
Thanks,
Chris

Multiple problems - help needed please

I've got so many problems that I've completely confused myself. So, if anyone can help….
I was previously using a D-Link D-320T DSL modem on BT Broadband in the UK. The modem was set up in bridge mode, and hooked up via ethernet to my Airport Extreme (n). The AEBS would use PPPoE and successfully connected to the internet, as well as handling all my network needs.
Everything worked and everything was fine, allowing screen sharing and file sharing between my Mac Mini, MacBook and MacBook Pro.
Earlier this week, the internet connection dropped and I couldn't find the cause. Resetting the router and hooking it up directly to my Mac Mini, I connected to it (192.168.1.1) and had it connect to the internet itself.
It did so, and distributed IP addresses to the Mac Mini…but after 30 seconds my internet connection dropped, and looking in network preferences, I found that the modem had jumped from a router address of 192.168.1.1, to an 82.xx.xx.xx address, which was clearly the public IP address forwarded by my ISP. So it seemed like it was working in a sort of bridge mode still.
I reset the router numerous times, tried switching it into full bridge mode etc, but the AEBS was unable to use it to connect via PPPoE as before, because the D-Link would play nice for 30 seconds, then jump around with addresses.
Very strange, but I assumed the modem was just broken.
I dug out my spare router, being the Netgear DG632.
I managed to get this hooked up to the internet really quickly, and using an ethernet connection to the Mac Mini, it all appeared fine. However, as I started looking around the internet, I noticed that although google.com would open up, any subsequent links, and indeed any other domains I tried to visit would not open.
Resetting the router seemed to solve this.
I then hooked up my AEBS to the Netgear and, after pondering which way to use it, I found the only way I could get it to play nice was to have the AEBS in bridge mode itself, meaning that the Netgear would do all the routing work.
The MacBook connected to the airport, and all seemed okay….
…However, I then noticed that the internet connection would randomly drop. Web pages would not open (in any browser), and downloads which were under way could be seen in the Safari download manager to suddenly crash.
The same was true on the Mac Mini - web browsing stopped at random. I had however hooked this up to the airport via an ethernet cable, I noticed that, although the "internet" wasn't working, other connections like torrents were still active.
Reconnecting the Netgear router directly to the Mac Mini allowed me to see in its diagnostics that it still held a connection to the ISP and still had an external IP address.
Again, a reset of the router seemed to resolve things….but only for a few hours. And whilst the Mac Mini seemed resilient, the airport connection to the MacBook was terrible. (I haven't even tried using the MBP yet).
Furthermore, I noticed that networking between devices had severely been crippled. Although the Mac Mini and MacBook were visible to each other in the shared devices section of finder, clicking the link meant waiting literally four minutes for a connection to establish, and screen sharing timed out, from either direction.
I then tried assigning everything static IP addresses, but this seemed to confuse matters with the router.
Under the impression that the Netgear clearly couldn't handle the job of routing my network, I tried to set it up in bridge mode and use the AEBS as before.
Reading around the internet (on my iPhone at this stage), I realised there was no obvious "bridge mode" option, but I was told to set the device mode as router, and then say "no" when it asks if there are any login details for the ISP (under Basic Router Settings). This was done.
However, setting up the AEBS with PPPoE had no success, and the connection was never made.
At this stage, I'm living with a crippled network and two routers, neither of which do what I want.
Can anybody advise me on a solution to fix either router/modem?
I want to use the modem in bridge mode and have the AEBS handle everything as before, as it was perfect.
At this stage, which a frazzled brain (after messing with everything for several hours), something step-by-step would be great.
Help! (and thanks)

I have also recently developed problems with my airport network. I was playing my air tunes when it started freezing so i reset my airport extreme and expresses. When I tried to setup my networks again I en counted problems like airport utility couldn't find the extreme base station or when it did it couldn't read the setting. I eventually managed to create a network then when i tried to connect to the network it either asks for the password (even though its saved in keychain) When I enter the password it keeps saying "connection time out". I then turn airpot off & on and it the sometimes reconnects automatically without requiring a password.
My internet then will sometime start working again but then drop out completely or take an age to load.
The network will then sometimes disappear from the network list and I'm unable to see it at all.
No matter how many time i reset the base station it doesn't make a difference.
I my broadband modem is also a wireless router and Im experiencing similar problems with that. I took my laptop to work and tried to connect to the network at work and it seems to work ok except it did ask for a password the time out but did it only once.
I did download a security update recently but im not sure if its that that is causing it
please help me as well as I'm stuck without my network

Basic java problem help needed please

the problem is :
to produce a program which will show membership rates for a golf club..
membership yearly rate new member joining fee
category
full 650 3000
associate 200
ladies 350 2000
under 18 175
new members must pay a joining fee in addition to the yearly rate as shown
full/ladies members also prepay 150
write a program which will enter details of members,calculate and output the total amount each member should pay.
output number of members in each category
the total income for each category....
i need this program to show each category individually...cant do it at all..been at it a week....must be me && and || signs...i think...plz can someone help me as im really stuck now...thank you so much..
import java.util.Scanner;
public class assignmentquestion3 {
public static Scanner key=new Scanner(System.in);
public static void main(String []args){
int fullfee=800,newfullfee=3800,associatefee=200,newla diesfee= 2350,ladiesfee= 350,under18fee = 175;
int selectcat=0;
int reply = 0;
int addmember=0;
int currentfulltotalmem=0,newfulltotalmem=0,associatet otalmem=0,ladiestotalmem=0,under18totalmem=0;
int assoctotalcash=0,ladiestotalcash=0,under18totalcas h=0;
int fullprepay=150;
int ladiesfull=2500;
int completefull = 0;
int ladiescurrent=500;
int under18=175;
//Main introduction screen for the user and selections available. do while loops only allowing numbers 1,2,3 or 4.
do{
do{
System.out.printf("\n\t %90s","********************Membership Rates For The Golf Club********************");
System.out.printf("\n\n %105s","This program will allow users to enter details of members as well as calculating and.");
System.out.printf("\n%106s","outputing the total amount each member should pay. The program allows users to view the");
System.out.printf("\n%106s","total number of members in each category and the total income for each category.");
System.out.printf("\n\n\t %75s","Please select your membership category: ");
System.out.printf("\n\n\t %68s","Please press '1' for FULL");
System.out.printf("\n\n\t %68s","Please press '2' for ASSOCIATE");
System.out.printf("\n\n\t %68s","Please press '3' for LADIES");
System.out.printf("\n\n\t %68s","Please press '4' for UNDER 18");
System.out.printf("\n\n\t %68s","Please enter 1,2,3 or 4: ");
selectcat=key.nextInt();
}while (selectcat>4 || selectcat<1);
do{
System.out.printf("\n\n\t %75s","Are you a Current Member (press 1) or a New Member (press 2): ");
reply=key.nextInt();
}while (reply<1 || reply>2);
//if number '1' for 'FULL' category is selected by the user and reply is 'yes'(1) then new full member fee is shown to user
if (selectcat==1 ||reply==1)
System.out.printf("\n\n\t %68s","CURRENT FULL MEMBERSHIP SELECTED");
System.out.printf("\n\n\t %68s","Current full membership fees yearly are "+fullfee+"");
System.out.printf("\n\n\t %68s","Full members must also pre-pay "+fullprepay+" on a card can be used in the club facilities such as bar and shop ");
System.out.printf("\n\n\t %72s","The total of this membership is: "+fullfee+"");
currentfulltotalmem=currentfulltotalmem+1;
System.out.printf("\n\n\t %72s","The total number of 'CURRENT FULL MEMBERSHIPS = "+currentfulltotalmem+"");
completefull=completefull+fullfee;
System.out.printf("\n\n\t %68s","The total amount of income for 'FULL MEMBERSHIPS' within the club = "+completefull+"");
//if number '1' is selected by the user and reply is 'no' (2) then full member fee is shown to user
else if (selectcat==1 &&reply==2)
System.out.printf("\n\n\t %68s","NEW FULL MEMBERSHIP SELECTED");
System.out.printf("\n\n\t %68s","Full membership fees yearly are "+newfullfee+"");
newfulltotalmem=newfulltotalmem+1;
System.out.printf("\n\n\t %68s","The total number of 'NEW FULL MEMBERSHIPS = "+newfulltotalmem+"");
completefull=completefull+newfullfee;
System.out.printf("\n\n\t %68s","The total amount of income for 'FULL MEMBERSHIPS' within the club = "+completefull+"");
//if number '2' is selected by the user then associate member fee is shown to user
if (selectcat==2 &&(reply==1 || reply==2))
System.out.printf("\n\n\t %75s","ASSOCIATE MEMBERSHIP SELECTED");
System.out.printf("\n\n\t %75s","ASSOCIATE membership fees yearly are "+associatefee+"");
associatetotalmem=associatetotalmem+1;
System.out.printf("\n\n\t %75s","The total number of 'ASSOCIATE MEMBERSHIPS' WITHIN THE CLUB = "+associatetotalmem+"");
assoctotalcash=assoctotalcash+associatefee;
System.out.printf("\n\n\t %68s","The total amount of income for 'ASSOCIATE MEMBERSHIPS' within the club = "+assoctotalcash+"");
//if number '3' is selected by the user and reply is 'yes' then new ladies member fee is shown to user
if (selectcat==3 &&reply==1)
System.out.printf("\n\n\t %68s","LADIES CURRENT MEMBERSHIP SELECTED");
System.out.printf("\n\n\t %68s","Ladies full membership fees yearly are "+ladiesfee+"");
System.out.printf("\n\n\t %68s","Ladies must also pre-pay "+fullprepay+" on a card can be used in the club facilities such as bar and shop ");
System.out.printf("\n\n\t %68s","The total of this membership is: "+ladiescurrent+"");
ladiestotalmem=ladiestotalmem+1;
System.out.printf("\n\n\t %75s","The total number of 'LADIES MEMBERSHIPS' WITHIN THE CLUB = "+ladiestotalmem+"");
ladiestotalcash=ladiestotalcash+ladiescurrent;
System.out.printf("\n\n\t %68s","The total amount of income for 'LADIES MEMBERSHIPS' within the club = "+ladiestotalcash+"");
//if number '3' is selected by the user and reply is 'no' then the current ladies member fee is shown to user
else
if (selectcat==3 && reply==2)
System.out.printf("\n\n\t %68s","LADIES NEW MEMBERSHIP SELECTED");
System.out.printf("\n\n\t %68s","LADIES NEW MEMBERSHIP fees yearly are "+newladiesfee+"");
System.out.printf("\n\n\t %68s","Ladies must also pre-pay "+fullprepay+" on a card can be used in the club facilities such as bar and shop ");
System.out.printf("\n\n\t %68s","The total of this membership is: "+ladiesfull+"");
ladiestotalmem=ladiestotalmem+1;
System.out.printf("\n\n\t %75s","The total number of 'LADIES MEMBERSHIPS' within the club = "+ladiestotalmem+"");
ladiestotalcash=ladiestotalcash+ladiesfull;
System.out.printf("\n\n\t %68s","The total amount of income for 'LADIES MEMBERSHIPS' within the club = "+ladiestotalcash+"");
//if number '4' is selected by the user then under 18 member fee is shown to user
else if (selectcat==4 &&(reply==1||reply==2))
System.out.printf("\n\n\t %75s","UNDER 18 MEMBERSHIP SELECTED");
System.out.printf("\n\n\t %75s","UNDER 18 yearly membership fees are "+under18fee+"");}
System.out.printf("\n\n\t %68s","The total of this membership is: "+under18+"");
under18totalmem=under18totalmem+1;
System.out.printf("\n\n\t %75s","The total number of 'UNDER 18 MEMBERSHIPS' within the club = "+under18totalmem+"");
under18totalcash=under18totalcash+under18;
System.out.printf("\n\n\t %68s","The total amount of income for 'UNDER 18 MEMBERSHIPS' within the club = "+under18totalcash+"");
//allowing user to select '0' to add another member or any other key to exit program
System.out.printf("\n\n\t %68s","Please Press '0' to add another member or any other key to exit.: ");
addmember=key.nextInt();
}while (addmember==0 ||addmember>1);}}
the problem im having is whenever i make the choices 1,2,3,4 (CATEgorys) AND hit 1 or 2(current or new member selections) it brings up more than one category...
for example when i hit 1(Category full) and 1(current member)..it displays this:
Are you a Current Member (press 1) or a New Member (press 2): 1
CURRENT FULL MEMBERSHIP SELECTED
Current full membership fees yearly are 800
Full members must also pre-pay 150 on a card can be used in the club facilities such as bar and shop
The total of this membership is: 800
The total number of 'CURRENT FULL MEMBERSHIPS = 1
The total amount of income for 'FULL MEMBERSHIPS' within the club = 800
The total of this membership is: 175
The total number of 'UNDER 18 MEMBERSHIPS' within the club = 1
The total amount of income for 'UNDER 18 MEMBERSHIPS' within the club = 175
Please Press '0' to add another member or any other key to exit.:
under 18 membership as well?...does this for other selections too...is it my arithmetic operators?....my if loops?...

Multi-post [http://forums.sun.com/thread.jspa?threadID=5346248&messageID=10498270#10498270]
And it still doesn't compile.

SQL problem - help needed ASAP!!

Hey guys,
Doing a college project... would really appreciate some help. I am trying to use a variable in the where clause of a select cursor in PL/SQL. The code is this:
procedure results(p_search_entry varchar2, p_search_field varchar2) is
cursor c_results is
select * from physics_b where p_search_field = p_search_entry;
begin
for cv_results in c_results
loop
-- loop through actions
end loop;
The problem is that I don't know how to get the where clause to accept the variable passed into the procedure as the field name. Does anyone know the syntax for this?
Thanks very much!
Niall

This isn't the correct forum for this kind of question. The SQL and PL/SQL forum PL/SQL is probably best.
That said, you can't do what you want that way.
You can do
procedure results (p_search_entry in varchar2)
cursor c_result is
select * fro physics_b where subject=p_search_entry;(assuming subject is a column in physics_b)
You can't use a variable to represent a column directly. You need to build the statement as a string and then use execute immediate.
statement:='select * fro physics_b where '||p_search_field||' = :1';
-- this bit is probably bad syntax.
execute immediate statement using p_search_entry;Look up execute immediate and bind variables

EMU 1212m installation problems! Help needed!

Similar Messages

Maybe you are looking for