Enable traffic only during office hours

hi,
is there a way to allow traffic on wireless network only during network hours ? i did not seen this feature in our controllers, is there any other way to disable the wireless network after office hours and schedule to get it enable next day before office hour.
thanks,
anvar

is there a way to allow traffic on wireless network only during network hours
Yes there are five (5) popular methods. And it will depend on what equipment you've got and/or how technically confident you are. The methods are:
You can enable time-based access on your Windows AD;
You can use time-based ACL and apply the ACL on the VLAN interface of your wireless network;
If you have WCS/NCS/PI, you can enable time-and-date to enable/disable the radios of the AP;
If you have WCS/NCS/PI, you can enable time-and-date to enable/disable the SSID; and finally
If your switch is Cisco then you can let the APs power down using EnergyWise.
Method 2 is popular and easy if you don't have Cisco WCS/NCS/PI. Option 4 is the most "destructive" because there's a chance your AP won't be powering up. This holds true of your AP is listed among the "Cisco Memory Component Issue".

Similar Messages

How do I get around or reset security questions that I have forgotten ie What was your first car ,without ringing during office hours?

How do I get past forgotton security questions for buying from store. ie What was your first car.

If you have a valid rescue email address, there’ll be a link to send a reset email to it. Use it, wait a few hours, and check the spam filter.
If not, wait for Apple’s office hours and then phone them.
If you’re desperate to make a purchase and have a credit card or unredeemed iTunes Store gift card, make a new Apple ID. iTunes Store credit and previous purchases can’t be transferred between them.
(110466)

Packet filtering and traffic shaping during peak h...

I play the online game World of Tanks and an currently exteriancing severe lagg and disconnects, the problem does not appear to be with the game/service provider but with BT, i need to know does BT use "packet filtering" and "traffic shaping" during peak hours and if so why has it suddenly started.
This game use's P2P to keep the latency down for players so have been advised to contact BT and ask them are they limiting these types of connections.
Most games do not use these types of connections, but World of Tanks one does and again,been told BT just don't like them, due to the amount of connections they attempt to forge in order to have a stable latency.
I need to know if this is going to continue as pay to play the game, therefore would have to consider changing my ISP to virgin who dont use "packet filtering" and "traffic shaping" during peak hours .
Quick advice would be appreciated.

It's absolutely horrible. i turned off wifi all other devices and every other open program just to reduce my latency for 120ms to 80ms.
Still suffer from huge packet loss.
It would be absolutely horrible if they have started throttling worldoftanks.eu servers. Phone support is no help all they torld me to do is restart my router
I hope this is fixed soon. There are many posts on the WoT eu official forums and everyone that is effected appears to be a BT customer.
Some have mentioned it could be the damaged undersea cable.
I don't have any problems with torrents being throttled or anything like that. only worldoftanks.eu being throttled.

Autocheck during business hours?

Is it possible to let my email automatically be checked only during business hours ?

Sure you can. When you leave work, go into settings and switch to manual, and when you get to work, switch it to auto-check

Enable email account only for certain hours?

is there a way to enable an email account for specific hours in a day?
I check my work email during work hours, and would like to disable that account after work. I have been doing this manually, but I was hoping there is a way to schedule when the email account is active...
Thanks in advance
I looked in settings > mail > fetch, but if the account is active, manual checking will still connect after hours...Basically, if I'm not at work, I don't want to know

thanks for the definitive answer, I will request this...
Of course, I would also like a similar feature in Mail, but that doesn't seem forthcoming either

Ipod Only Playing During Certain Hours

Ok, so my iPod is acting up and I am not sure what to do. I can only listen to my iPod during certain hours. This includes both with the headphone jack and also with the FM Transmitor. Tried looking through the menu on the actual iPod to see if there was a setting option or something that I accidentally pushed, but no. The counter is running, however no sound is coming out. Any ideas what might be causing this or how to fix it?

Unfortunately, they would have to create a new "temporary" event each work day. Alternatively, you can send them a permanent invite, and they can go to Settings > Location Services > Find my Friends OFF when they don't want to be tracked.

Unable to allow traffic from remote office - Cisco RV220W

Hi there,
I have just bought the RV220W Cisco router firewall because my DLINK-1600 got broken and now I am unable to allow access to the machines located behind this router from the machines located at a remote office. Any help would be much appreciated!!
This is the situation:
1. Two remote offices A and B connected by a VPN tunnel (this connection is managed by an external provider and it is properly functioning)
2. IP range A office: 192.168.236.0/24
3. IP range B office: 192.168.237.0/24
4. Office A: CISCO RV220W router/firewall (the one that I´ve just bought as the old dlink has broken). This RV220W is connected to a cisco router (managed by provider) that is the one with the VPN tunnel to the other office. The CISCO router does not do NAT. On the other end (Office B) there is another CISCO router managed by the provider.
5. Everything was working smoothly until our old router/firewall got broken and that is when I bought the rv220w. I have set up the CISCO RV220W at office A and the machines can ping the machines located at office B and can browse the internet, i.e., the traffic going out is OK and in that sense everything works smoothly.
6. The problem is that the machines located at office B cannot access the machines located behind the CISCO RV220W and I know it is a problem of the firewall as if I capture traffic coming from office B, I can see that it is dropped by the CISCO RV220W.
7. I have tried to enable an access rule in the firewall to allow traffic from office B (see picture below) but it does not seem to work. In the field, Send to Local Server (DNAT IP) I have entered the WAN IP of my router (you cannot leave it blank) … this rule does not work at all. I think that is not properly configured but I don´t know how to do it.
8. As you see, the problem is that I don´t know how to set up a rule to allow specific traffic coming from the WAN (traffic from remote office – 192.168.237.0/24) to the LAN at office A - 192.168.236.0/24.
In the old router/firewall I just had to create a rule specifying the source interface (WAN) and network (Office B) and the destination interdace (LANOfficeA) and network (Office A). It does not seem that here I can do the same. i mean, you always have to point to a server ip inside the LAN??
I know it has to be a very easy thing to do but at this moment I am completely stuck. If anyone can give me some advice would be great.
Thanks a lot for your help in advanced!
Eva

Hi Eva, the default inbound policy cannot be changed. It will block all inbound traffic. To my knowledge there is not a way around this. Access rules are the only way to 'poke' a hole through the firewall but as you note, it is for a specific host. Values such as .0 and .255 do not work.
-Tom
Please mark answered for helpful posts

Yes Verizon has contacted me by phone. I never scheduled a call time nor did I call them. They also are not making it easy to contact them through email. I need to discuss a way to assure that my phone is never called again during work hours without a

Yes Verizon has contacted me by phone. I never scheduled a call time nor did I call them. They also are not making it easy to contact them through email. I need to discuss a way to assure that my phone is never called again during work hours without a prearranged meeting. I will not speak on the phone nor use a live chat. I want email as I want this documented offical and no other means offeres me that assurance. I'd also like to discuss comensation for being harrassed with phone calls.

Well if you pay your bill the calls would not happen.
You need only tell them not to call you during working time.
The Fair Debt Collections Practices Act states you must tell them it is not convenient.
Now if marketing calls you can opt out at the Verizon web portal under your My Verizon account.
You will not get compensation for them to call you. Nice try.
However they could just shut your phone off and then you will call them.
Email is not an option.
Good Luck

Outgoing Call block on operator 7961 after office-hours

Hi guys,
we have call block enabled on our ccme 4.2 for 900 pattern and all users use pin to
make international calls.Now we want to block all 9.T pattern after office hours for operator phones only .please advise

Thanks Nadeem for your reply but the issue is i want to block outgoing calls
after office only for reception phone. other phones should work normal
we are blocking 24/7 international call using call blocking,users use login pin
so if i put other pattern of 9.T For local ,national and international to block after office-hours all phones will get blocked and all uses have to use pin after office to make calls
plus cant put after-hours exempt then cannot control users with international pin dialing
plz advise

How can I disable web/data access during certain hours?

I have added a feature to my wireless account restricting my daughter's text/data/surfing access during evening hours. I thought I was pretty clever and assumed she would only have access to her music on her iPhone. Turns out she can still access all she wants using our home WIFI so my sceme is rendered useless. Other than confiscating her phone each evening, does anyone know how I can restrict wifi on her phone during certain hours?
Also, does anyone have a nano? Thinking she could use that for music and to set her alarm, but I don't think the nano has an alarm function.
Thanks for your input!

No way to restrict it during certain hours. You can restrict it always, or never. Parental supervision is one solution. It's a losing battle to try to outwit children. It's better to require trust, with consequences if trust is breached.

Traffic only allowed one-way for VPN connected computers

Hello,
I currently have an ASA 5505. I have set it up as a remote access SSL VPN. My computers can connect to the VPN just fine. They just can't access the internal LAN (192.168.250.0). They can't ping the inside interface of the ASA, or any of the machines. It seems like all traffic is blocked for them. The strange thing is that when someone is connected to the VPN, I can ping that VPN-connect machine from the ASA and other machines inside the LAN. It seems the traffic only allows one way. I have messed with ACL's with no avail. Any suggestions please?
DHCP Pool: 192.168.250.20-50 --> For LAN
VPN Pool: 192.168.250.100 and 192.168.250.101
Outside interface grabs DHCP from modem
Inside interface: 192.168.1.1
Current Running Config:
: Saved
ASA Version 8.2(5)
hostname HardmanASA
enable password ###### encrypted
passwd ####### encrypted
names
interface Ethernet0/0
switchport access vlan 20
interface Ethernet0/1
switchport access vlan 10
interface Ethernet0/2
switchport access vlan 10
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
switchport access vlan 10
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan10
nameif inside
security-level 100
ip address 192.168.250.1 255.255.255.0
interface Vlan20
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
pager lines 24
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool 192.168.250.100-192.168.250.101 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 10 interface
nat (inside) 10 192.168.250.0 255.255.255.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 192.168.250.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh 192.168.250.0 255.255.255.0 inside
ssh timeout 5
ssh version 2
console timeout 0
dhcpd dns 8.8.8.8
dhcpd address 192.168.250.20-192.168.250.50 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
svc image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
svc image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2
svc image disk0:/anyconnect-linux-2.5.2014-k9.pkg 3
svc enable
tunnel-group-list enable
group-policy DfltGrpPolicy attributes
dns-server value 8.8.8.8
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
tunnel-group AnyConnect type remote-access
tunnel-group AnyConnect general-attributes
address-pool VPN_Pool
tunnel-group AnyConnect webvpn-attributes
group-alias AnyConnect enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:30fadff4b400e42e73e17167828e046f
: end

Hello,
I seem to be having the same kind of issue although I cannot ping from either end.
Ive set up a l2tp/ipsec vpn which I am able to connect to and get ip from my ip pool (radius authentication is working).
I tried running:
access-list NAT_0 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
nat (inside) 0 access-list NAT_0
but i get an error msg saying that the syntax of the nat command is deprecated. Im running ASA version 8.4.
Ive fiddled around abit to find the correct syntax but have been unsuccessfull so far.
Any help would be much appreciated
This is a part of my config:
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network AD1
host 192.168.1.31
description AD/RADIUS
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network vpn_hosts
subnet 192.168.2.0 255.255.255.0
access-list AD_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
access-list split-acl standard permit 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.1.0 255.255.255.0
access-list inside_0_outbound extended permit ip object NETWORK_OBJ_192.168.1.0_24 object vpn_hosts
ip local pool POOL2 192.168.2.2-192.168.2.10 mask 255.255.255.0
nat (inside,outside) source static any any destination static NETWORK_OBJ_192.168.1.0_25 NETWORK_OBJ_192.168.1.0_25 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static NETWORK_OBJ_192.168.1.0_25 NETWORK_OBJ_192.168.1.0_25 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static vpn_hosts vpn_hosts
object network obj_any
nat (inside,outside) dynamic interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 ########## 1
no vpn-addr-assign aaa
no vpn-addr-assign dhcp

Thank you. Save or print this page for your records. We'll also send you an email confirmation. Case ID: 421912520 You have chosen to call Apple later. When you're ready, call the phone number below during business hours and refer to your Case ID for fas

Thank you.
Save or print this page for your records. We'll also send you an email confirmation.
Case ID: 421912520
You have chosen to call Apple later. When you're ready, call the phone number below during business hours and refer to your Case ID for faster support.
1-800-MY-IPHONE
6:00 a.m. to 11:00 p.m. Central
iPhone
Restore or update not working as expected
You can review this case in the Cases & Repairs section.
Additional Resources
Return to Apple Support home.
Visit your Support Profile.
Create another support request.
Your contact information
Onechai John
<Email Edited by Host>

They already have your number and/or email address and maybe have sold it several times already to others as well. They also use number generators - software that will automatically create them - some work and some don't, they don't care, they send out millions and a few will fall for it and send them money. The only way to "hide" would be to change both and your password, but then it would happen again at some point.

Hi I'm using iPhone 5s ..I don't use much but face battery issues ..usage comes only for 3 hours if I use wifi ..can someone tell if you are facing this issue ..

Hi I'm using iPhone 5s ..I'm facing problems with battery ..usage time is only 3-4 hours if I use wifi and I don't use much ..can somebody please tell if you're experiencing the same problem ..average users get around 9-10 hours or even more

Hello MengyaLiu, and welcome to the forum,
I’m honestly not sure why our delivery team would have told you they were on their way to your home and then not arrive without an explanation as to why. Our delivery agents should be notifying you of all necessary changes in their delivery schedules, as we realize the inconvenience any possible delay may cause, so it’s regrettable to hear we failed you in this regard. I truly apologize for any frustration this oversight may have caused.
While I’ve personally documented your feedback here at the corporate office to ensure something of this nature doesn’t happen in the future, I’m glad to hear our delivery team was able to make this right and successfully delivered your TV yesterday. Please feel free to let us know how it went and if you have any further questions for me. I’ll be glad to help.
Best wishes,
Alex|Social Media Specialist | Best Buy® Corporate
Private Message

Nada Happened During One Hour

Hello all!
I was just wondering if others have had the same issue: since I upgraded for the OS 3.0 on my iPhone 3G, regularly I couldn't send text messages. The "Sending" bar would stop at 90% ish and send I would receive the "failure to send message" notification.
It happened sometimes only so I was not worried. But then, 2 days ago my phone froze completely during one hour: couldn't send any text message to anyone, couldn't browse internet or send emails, couldn't launch any application using 3G.
So I decided to restore my iPhone and upgraded to 3.1 at the same time. Looks to be working fine for now .
I just wanted to share my experience that's all
V.
P.S. Some of my data were not restored with everything else

Hi Canon Forum.
I know this is a replay to a non related thread, but since it was not possible to make a new thread, I have to do it this way.
I have a serious connection problem with my MVX4i Canon Camcorder.
First my hardware:
O/S: Win7 64bit
What happens:
I've installed the drivers but I keep getting the error "cannot detect camera".
In my device manager it claims that the drivers cannot be installed and even though I manually search for them (on the installation CD or the installation directory) it refuses to install them.
What I have tried:
I've tried using different USB ports - no luck
Used different USB cables - no luck
Tried uninstalling EVERYTHING, disconnecting camcorder and installed drivers again - no luck
I've tried drivers from your website instead of the CD - no luck.
What in gods name can I do to get my PC to connect with my camcorder??

Refurbished Gen5 touch, battery only lasting 12 hours of music on low is this normal?

Apple store refurbished Touch Gen 5 touch with new iOS only lasting 12 hours of music play on low, in airplane mode turned on. Is this normal? Or do I need to charge than fully discharge afew times. Thank-you for any assistance.

That is a little low. Was the screen on during that time?
Was wifi on?
The following included actions to maximize battery life.
Apple - Batteries - iPod
What life do you get after fully charging and almost fully discharging a couple of times.

Enable traffic only during office hours

Similar Messages

Maybe you are looking for