Encode ProRes From Tape

Can I encode from video tape (not from camera) and make ProRes file, both 422 and 4444?  I use to use Final Cut for this but...well, you know.

What do you mean by "encode from video tape?" Do you mean capture? I think you can, if you have the appropriate hardware, e.g. a third-party capture card, and FCP installed. Obviously, this is only available on the Mac, which I'm assuming you're using since you referred to FCP.
Or do you mean something else?

Similar Messages

  • Encoding ProRes HD to ProRes 16x9 SH

    I have not found a preset for this in Compressor, am I missing it?
    Anyone else doing this?
    We have been editing HDV and exporting via HDV/DVCam tape where the company authoring the DVD then down converts in the Sony HVR-M25U and captures DV then MPEG encodes directly from the FCP project.
    Two things, we are tired of dealing with all of the foibles associated with HDV (conforming) and the quality of this workflow is marginal.
    Since they are encidong from FCP we could just as easily deliver an SD ProRes file which would remove the necessity for long conforming times and better quality.
    Anyone have a recipe for this?

    So, HDV to SD? What frame rate to what frame rate?

  • Recovery of VHD file from tape immediately gives null error, ID 1001, and job fails.

    I am attempting to recover a VHD from tape.   When I finish the recovery wizard and it starts to create the job, I get an immediate popup error with an ID: 1001 and a "More Information" link that goes to a "page not found" on technet.
     There is no actual errror message or other info in the dialog box.  When I click ok, the dialog and recovery wizard disappear, and no job seems to have been created. 
    I've seen a couple of other posts about this, but didn't find any solutions.  I did run a tape verification against the recovery point in question, and it completed.  (I don't see where it says passed/failed, just completed.  I assume the
    job would have failed if it found a problem?)
    I've also tried a couple of other recovery points, on different tapes, but am getting the same results. 
    Any idea what is going wrong?

    Hi,
    Can you provide DPM version and update rollup version.  Are there any events from MSDPM after the error, if so, can you supply the event details ? 
    As a workaround,  you can restore the VHD by going to Management>Tape Library>Right Click on the Tape>select backup set for the data source containing the VHD and then click on the COPY button.  That will restore to
    a network location and you can then copy it to the hyper-v server and replace the VHD manually.
    Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT]
    This posting is provided "AS IS" with no warranties, and confers no rights.

  • Five days ago I received an email from an anonymous sender with the subject: Your Apple ID was just used to buy full album Elton John 312.99. Your receipt No. 37930343160405752. the content began: Content-Transfer-Encoding: base64 From (my email add

    Five days ago I received an anonymous email with the subject:
    Your Apple ID was just used to buy full album Elton John £12.99.Your receipt No.37930343160405752
    The content started: Content-Transfer-Encoding: base64 From:(my email address) followed by a very,very,very long stream of gobbledygook. There is no record of it in my i-tunes purchases or my credit card statement but that might only be because I have not updated my credit card details. Should I be worried that my account has been compromised? Does anyone know how I can get through to the right section of Apple to deal with this - all the emails I get say no-reply so I don't have an email address to contact them on.
    I would be most grateful if anyone could help me with this.
    Thanks in advance
    Walwal

    It's a phishing attempt to try and get your account and payment details - forward it to Apple : [email protected] , and then delete it
    Phishing emails : Identifying fraudulent "phishing" email - Apple Support
    Genuine emails : Identifying legitimate emails from the iTunes Store - Apple Support

  • RMAN recovery from tape and disk?

    Hey Guys,
    Here is my scenario: -
    I have Oracle 10g and I am using RMAN to backup to disk and then I use Networker to backup on tapes from disk (retention is set to 30 days on tapes). On RMAN - my retention policy is set to recovery window of 5 days after which it deletes the obsolete backup from disk and updates the control file.
    My Questions:
    1. If I have to recover any datafile or tablespace 20 days ago how can I restore it on Production. Since I am also backing up control files on tapes but my current control file will not have 20 days old information. Is there any way that I can restore my old backup?
    2.How can I test my tape backup which is older than 5 days. In other words how can I restore my database from tape on another server/
    Please suggest.

    If you need to restore the whole database to a point in time that is 20 days old, you "only" need:
    1. to identify the right control file backup
    2. restore this control file backup with Networker
    3. start the instance in mount mode
    4. list required datafiles and archived redo logs backup sets listed in this control file with LIST BACKUP
    5. restore these backup sets with Networker
    6. restore and recover database with RMAN with the right SET UNTIL clause.
    If you need to restore only 1 tablespace, that's Tablespace Point In Time Recovery (TSPITR) and is another story.
    I don't think you can only restore 1 datafile that is 20 days old and leave other datafiles up-to-date (unless there is only 1 datafile in the tablespace and in this case this is TSPITR).

  • How to restore a Rman backup from Tape

    Hi,
    We need to restore the database backup taken through RMAN on 24-JUNE-2013 from tape as this backup is not currently available on disk.
    Can you please help me on the following,
    1) how i can check if the same backup on 24-JUNE-2013 is available on Tape.
    2) If yes how i can restore to Disk.
    Because we need to create a new Clone instance from the backup taken on 24-JUNE-2013.
    We are having 12.1.3 Application on Exalogic and 11.2.0.3 Database on Exadata machine.
    Our support is highly appreciated.
    Thanks

    user11969666 wrote:
    Hi,
    We need to restore the database backup taken through RMAN on 24-JUNE-2013 from tape as this backup is not currently available on disk.
    Can you please help me on the following,
    1) how i can check if the same backup on 24-JUNE-2013 is available on Tape.
    2) If yes how i can restore to Disk.
    Because we need to create a new Clone instance from the backup taken on 24-JUNE-2013.
    We are having 12.1.3 Application on Exalogic and 11.2.0.3 Database on Exadata machine.
    Our support is highly appreciated.
    Thanks
    Your questions are answered in the Backup and Recovery User's Guide -- Contents
    Thanks,
    Hussein

  • Database Restore & Recovery from tape

    Hi Fellows
    I'm about to attempt a recovery from backup tape to a test server, as a 'tape recovery' test. The files I've marked for recovery include (directories including all sub-tree);
    Datafiles directory
    $ORACLE_HOME/sid/ directory where the sid is the database sid
    Control Files
    adump, Bdump, cdump and udump directories
    Archivelogs directory
    Flashrecovery area directory
    Redo logs directory
    initfile and spfile
    With these files recovered (from one point in time), and the dbconsole shut down prior to restore (for the sid) should the database be able to startup afterwards? Is there any other actions I should make? Thanks, David

    Thanks for your responses Alok and Santosh
    I'm pretty sure the files I have selected should be able to recover the database. The recovery, I think is rightly said, can only be done within Oracle. I'll look into a test of RMAN (I know it should be better) recovery once I've tested this as a 'straight from tape' recovery.
    Thanks again, David
    Alok and Santosh
    I thought I'd put this in as 'aftermath' of the attempted recovery;
    I had the server team restore the files stated (basically everything - redo, archivelogs, datafile, controlfiles, init and sp files, even the dump files) - and repalced them into directories made the same as the other server. When I started it, I was able to go into a 'Oracle Suggested' full database recovery, which was successful. I then checked the expdp dump files, 1 taken at the same time of backup as rman - and one directly after the restore), and compared rows - exactly the same. So appears to have worked.
    Many thanks, David
    Message was edited by:
    David_W

  • Splitting events when capturing footage from tape

    Using Final Cut Pro x, I want to capture footage from tape which is of a more then one event. what is the best way of doing this so as to avoid all of the footage captured as one event.

    One way of doing this is to simply go into the Import from Camera window and select the clips that belong to one event then hit the Import Selection button.  A window will come up asking you which event you want to import to and also give you the option to create a new event.  After the little clocks fill up on each of the selected clips, that import is done.  Now you can select the other clips and import them in the same way specifying a new event when you are asked where they are to go.  Best wishes.
    stpehen

  • How much loss in capturing from tape?

    Looks like the days of tape are numbered.  If they haven't already, everyone will be using tapeless formats before too long.  I have a large library of HD (miniDV format) tape.  When clients want raw footage, I copy tape-to-tape using two camcorders and send a copy of the raw footage.  That will soon be impossible, because no one will be able to play the tapes. What's left is to use CS4 to capture the tape footage directly to a hard drive or memory stick and send that. I have no idea how much loss of data there is doing that, and hope someone might have some numbers to share.
    Thanks.

    A Firewire transfer from tape to computer is a copy operation... so there is no loss of quality
    Of course, those files are "about" 13Gig per hour for DV (I don't know the size for HDV) so sending a file to someone is going to mean several DVD's to write the files, in 4Gig segments, or copying to a USB hard drive and sending that back and forth

  • How to upload Unicode encoding files from web?

    Hi everyone,
    I do not manage to upload Unicode encoding CSV files from web. Currently I use class CL_HTMLB_MANAGER to upload file from web. It works fine with ANSI encoding files, but file content is not uploaded correctly with Unicode encoding files. Especially I get innumerable characters u201C#u201D throughout the string that contains the file content (For example instead of u201CSAP CATALOG CSV 2.0u201D I get u201CÿþS#A#P# #C#A#T#A#L#O#G# #C#S#V# #2#.#0#u201D).
    I did not find in forums a solution to my issue that is why I am now asking for your help.
    How can I upload Unicode encoding files from web? Do you know another way to upload file from web that is Unicode compatible?
    Remark: I tried to upload Unicode encoding files from SAP GUI using function module GUI_UPLOAD and upload is successful.
    Here is the code that I currently used.
    DATA:     lr_event_ex     TYPE REF TO if_htmlb_data,
               fileupload      TYPE REF TO cl_htmlb_fileupload,
               lr_upload_model TYPE REF TO /ccm/cl_bsp_upload_model,
               lr_error        TYPE REF TO /ccm/cx_file_upload.
    lr_event_ex =  cl_htmlb_manager=>get_event_ex( runtime->server->request ).
    IF lr_event_ex->event_name = 'fileUpload' AND lr_event_ex->event_type = 'upload'.
      fileupload ?= lr_event_ex.
      FREE lr_event_ex.
    * get the model
      lr_upload_model ?= me->get_model( model_id = 'mupl' ).
      IF NOT fileupload->file_name IS INITIAL.
    *   upload data
        TRY.
            CALL METHOD lr_upload_model->upload_data
              EXPORTING
                iv_file_name = fileupload->file_name
              CHANGING
                cv_xcontent  = fileupload->file_content.
          CATCH /ccm/cx_file_upload INTO lr_error.
        ENDTRY.
        FREE fileupload.
      ENDIF.
    ENDIF.
    Thank you in advance for helping me.
    Best regards,
    Vanessa

    Hi There,
    Please check the details for the same.
    Link: http://helpx.adobe.com/creative-cloud/help/sync-files.html#Sync or upload files
    Troubleshoot sync:     
    Error: "Unable to sync files"
    Creative Cloud File Sync | Known issues
    Thanks,
    Atul Saini

  • Preferred video format...from tape to...?

    I have a client that will transcode from tape to digital file for me. Since I want great quality video what is the best format and specs I should ask them to deliver so I can edit directly with FCP?

    Depends on the tape format. DV, HDV, DVCPRO HD...all can be captured natively. Digibeta, Beta, HDCAM, D5...all need to be captured into another format...Uncompressed.
    So...what have you got?
    Shane

  • When I capture from tape, express 4 now breaks my captured material into separate shots, an icon in the browser for each. Before it captured the whole clip till I hit escape, and created just one Icon. How to i get back the way it was.

    When I capture material from tape with final cut express 4, it used to create one icon for the whole clip. Now, when i capture, it breakes  the material down into many browser icons, shot by shot. I dont want that. How to I return to what I ahd before/

    What you describe is normal behavior for HDV capture using FCE.
    DV captures as one clip or may split the clip if there are timecode breaks on the tape.
    HDV always breaks clips at the shot changes using FCE.
    HDV cameras can downconvert to DV even if HDV was used to record the footage so it's important to know what the camera outputs during FCE capture.
    Maybe this is why you have had mixed results with the differing capture windows?
    Al

  • Sun Solaris 10 restore OS from tape

    Hi, can somebody help. Problem as below. Can't boot OS (solaris 10) after restoring it to new disk from tape.
    Boot device: /pci@1f,700000/scsi@2/disk@1,0 File and args:
    SunOS Release 5.10 Version Generic_118833-24 64-bit
    Copyright 1983-2006 Sun Microsystems, Inc. All rights reserved.
    Use is subject to license terms.
    Hardware watchdog enabled
    Hostname: esora40
    ERROR: svc:/system/filesystem/root:default failed to mount /usr (see 'svcs -x' for details)
    [ system/filesystem/root:default failed fatally (see 'svcs -x' for details) ]
    Requesting System Maintenance Mode
    (See /lib/svc/share/README for more information.)
    Console login service(s) cannot run
    Root password for system maintenance (control-d to bypass):
    single-user privilege assigned to /dev/console.
    Entering System Maintenance Mode
    Nov 22 14:13:35 su: 'su root' succeeded for root on /dev/console
    su: No shell /bin/ksh. Trying fallback shell /sbin/sh.
    -sh: /bin/i386: not found
    -sh: /usr/sbin/quota: not found
    -sh: /bin/cat: not found
    -sh: /bin/mail: not found

    Try boot -m verbose and see if it provided any clues.
    Otherwise, you havent provided enough info for anyone to suggest anything.
    I'm not aware of any "generic" solaris 10 issues in this area, so its probably something specific to your environment.
    Post the content of /etc/vfstab.
    And the output of format when booted from cd/network.
    And a df output when the filesystem are mounted.

  • Restore controlfile from tape backup without autobackup setting on

    I am testing a scenraio of restoring control file if we loose all control files.
    My RMAN settings for CONTROLFILE AUTOBACKUP is OFF. But, I have taken a backup of controlfile using 'BACKUP CURRENT CONTROL FILE' .
    When I tried to restore control file. I am receiving following error:
    RMAN> run {
    2> allocate channel c101 type sbt_tape;
    3> restore controlfile ;
    4> }
    allocated channel: c101
    channel c101: sid=153 devtype=SBT_TAPE
    channel c101: VERITAS NetBackup for Oracle - Release 6.0 (2006110304)
    Starting restore at 24-MAY-2007 13:44:59
    using channel ORA_DISK_1
    RMAN-00571: ===========================================================
    RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
    RMAN-00571: ===========================================================
    RMAN-03002: failure of restore command at 05/24/2007 13:44:59
    RMAN-06563: control file or SPFILE must be restored using FROM AUTOBACKUP
    My question is, How can I restore control file from tape backup without CONTROLFILE AUTOBACKUP setting ON.
    It sounds like, There is no way we can restore control file from tape backup if you've not set the CONTROLFILE AUTOBACKUP is ON.
    Please advice

    When all controlfiles are lost and a recovery catalog is NOT used, RMAN has no information , where to find the controlfile backup. It's not enough to specify the channel, such a channel could hold many different backups from many different databases. You have tell , which database and which backupset. Modify your run block:
    SET DBID <DBID of the database,for which you want to restore the controlfile>;
    RESTORE CONTROLFILE FROM <name_of_backupiece_which_contains_the_controlfile backup>';
    Werner

  • Restore backupsets from tape.

    Hi,
    We are on a 2 node RAC cluster, ASM. We run backups through rman.
    Scenerio:
    Rman backup runs and create backupsets in ASM diskgroup. We again run a tape backup to backup the backupsets to tape and delete the backupset from disk.
    My question:
    How can i restore the backupsets back to disk, if i have to restore a database?
    I use the following to backup the backupsets to tape:
    backup backupset completed before 'sysdate-2' delete input
    But i'm not sure of what command to use to restore the backupsets back from tape to disk if i need to restore the database? Any help appriciated.
    Thanks
    Karthik

    Hi,
    You are keeping latest backups on disk and in case of any Disk failure, when you run RESTORE/RECOVER it will use the backups from disk.
    In case if RMAN need more files then automatically restores needed archived logs from tape to disk during recovery.
    Please keep backups in a separate ASM diskgroup, which should not contain active database files such as datafiles, control files, and online redo logs.
    Regards,
    Satishbabu Gunukula
    http://oracleracexpert.blogspot.com

Maybe you are looking for